Structural effects of dopants and polymerization methodologies on the solid‐state ordering and morphology of polyaniline

The solid‐state three‐dimensional ordering of polyaniline–dopant complexes was investigated with four structurally different sulfonic acid dopants. The doped materials were produced in three different ways: polyaniline emeraldine base doped with sulfonic acid (aqueous route), in situ polymerization at the organic–water solvent interface (interfacial route), and in situ polymerization in organic and aqueous solvent mixtures (bilayer route). p‐Toluenesulfonic acid (PTSA), 5‐sulfosalicilic acid (SSA), camphorsulfonic acid (CSA), and dodecylbenzene sulfonic acid (DBSA) were employed as dopants. The conductivity of the aqueous‐route samples showed 10 and 100 times higher conductivity than the interfacial and bilayer routes, respectively. WXRD studies suggested that the crystallinity of the doped samples was dependent on both the structure of the dopants and the polymerization techniques. DBSA increases the polyaniline interplanar distance and produced highly crystalline materials via the aqueous and bilayer routes but failed with the interfacial route because of poor solubility in water. CSA, PTSA, and SSA produced highly crystalline samples by the interfacial route but failed with the aqueous (except for CSA) and bilayer routes. SEM analysis revealed that the doped materials of the interfacial route had excellent continuous morphology and uniform submicrometer‐size particle distributions in comparison with those of the aqueous and bilayer routes. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1321–1331, 2005     

Tubular polypyrrole synthesized by in situ doping polymerization in the presence of organic function acids as dopants

Tubular polypyrrole (PPy) could be synthesized by in situ doping polymerization in the presence of β‐naphthalene sulfonic acid (NSA) as dopant. The resultant tubular PPy–NSA not only exhibits high room temperature conductivity (ς_RT = 10 S/cm) but is also soluble in m‐cresol. The molecular structure of PPy–NSA is identical to the characteristic structure of PPy synthesized by a conventional method. It has been demonstrated that NSA dopant with large molecular size and plate–lebe structure is a key factor to control formation of tubular PPy–NSA. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1443–1449, 1999     

Soluble conductive polypyrrole synthesized by in situ doping with β-naphthalene sulphonic acid

Soluble polypyrrole (PPy) with high conductivity (27 S/cm) has been prepared by chemical polymerization of pyrrol monomer in the presence of β-naphthalene sulphonic acid (NSA) as a dopant. The solubility of the resulting conducting polymer of PPy-NSA in m-cresol increases with increasing the concentration of NSA in the polymerization media, and the highest solubility of PPy-NSA in m-cresol is about 1.2 g/100 mL. The room-temperature conductivity of PPy-NSA significantly increases with the concentration of NSA when the concentration of NSA is less than 0.1 mol/L, while it slightly decreases with increasing the concentration of NSA after the concentration of NSA is higher than 0.1 mol/L. UV-VIS spectra and ESR measurements demonstrate that both polaron and bipolaron are present as a charge carrier. The resulting PPy-NSA exhibits unusual fibrillar morphology with a diameter of about 0.5 μm, which is quite different from the granular morphology of PPy doped with dodecyl benzene sulfonic acid (DBSA) and HCl. Moreover, the polymerization conditions greatly influence the morphology of the obtained PPy-NSA. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 3689–3695, 1997     

Studies on formation mechanism of polypyrrole microtubule synthesized by template‐free method

The influence of the polymerization time and rate as well as the solution's ionic strength on the morphology, conductivity, and molecular structure of the polypyrrole (PPy) microtubule [synthesized by the template‐free method in the presence of β‐naphthalene sulfonic acid (β‐NSA) as the dopant] were investigated. It was found that the formation of the PPy‐NSA microtubule was a slow and self‐assembled growth process. Moreover, the β‐NSA dopant played a “templatelike” role in the formation of tubular PPy‐NSA, which might be relative to its surfactant characters. This assumption was further confirmed by the phenomenon that the morphology of PPy‐NSA could be modified by increasing the ionic strength by adding inorganic salt. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 997–1004, 2001     

Synthesis and characterization of new azobenzenesulfonic acids doped conducting polyaniline

New azobenzene sulfonic acid dopants were synthesized by diazotized coupling reaction of sulphanilic acid diazonium salt with commercially available raw materials such as phenol, m-cresol and 4-phenylphenol. The structures of the dopants are confirmed by NMR and FT-IR. Polyaniline emeraldine base was doped by these new azobenzenesulfonic acid dopants in two different solvent medium such as methanol and N-methylpyrrolidinone to produce green emeraldine salt. The doping process was confirmed by FT-IR and UV-vis spectroscopy. The effect of composition of dopant on the conductivity of the polyaniline was investigated and the results suggest that the conductivity increases with the increase in the dopant concentration and attained maxima for more than 38% in the feed. The conductivity measurements reveal that all the dopants equally effective in producing in high conductivity in the range of 0.02 S/cm and the conductivity of the doped samples are insignificant to the structural difference in the dopant. WXRD and SEM analysis indicate that the doped samples are highly amorphous and porous in nature. The thermal analysis by TGA indicate that all the doped materials were highly stable up to 300 °C for high temperature applications.     

Polypyrrole/poly(N‐isopropylacrylamide‐co‐acrylic acid) thermosensitive and electrically conductive composite microgels

The electrically conductive polypyrrole/dodecylbenzene sulfonic acid/poly(N‐isopropylacrylamide‐co‐acrylic acid) (PPy/DBSA/poly(NIPAAm‐co‐AA)) composite microgels were synthesized by a chemical oxidation of pyrrole in the presence of DBSA as the primary dopant, and poly(NIPAAm‐co‐AA) microgels as the polymeric codopant and template, in which APS was used as the oxidant. It was proposed to prepare “intelligent” polymer microgel particles containing both thermosensitive and electrically conducting properties. The polymerization of pyrrole took place directly inside the microgel networks, leading to formation of composite microgels and the morphology was observed by transmission electron microscope. PPy particles interacted strongly with microgels, as the acid groups of microgels acted as the polymeric codopant. The composite microgels thus formed showed electrically conducting behavior dependent on humidity and temperature. At temperatures lower than lower critical solution temperature, the conductivity decreased with increasing the humidity and a small hysteresis phenomenon was observed. The hysteresis became indistinct when temperature was near volume phase transition temperature. However, after the treatment of high temperature and high humidity, the conductivity increased surprisingly due to the structure reorganization inside the composite microgels. The distinctive functionality of the PPy composite microgels was expected to be utilized in many attractive applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1648–1659, 2006     

Hollow microstructures of polypyrrole doped by poly(styrene sulfonic acid)

Microstructures with hollow interiors, such as microspheres, microcrocks, microbowls, and micropumpkins, were prepared through the direct electrochemical oxidation of pyrrole in an aqueous solution of poly(styrene sulfonic acid) (PSSA). Scanning electron microscopy demonstrated that the microstructures possessed hollow interiors. The addition of polymeric doping ions made the skins of the microstructures very smooth, and several novel structures were observed. The morphology of the microstructures was simply modulated through changes in the electrochemical conditions. Raman and Fourier transform infrared characterizations indicated that the microstructures were made of conductive polypyrrole (PPy) doped by polymeric anions of poly(styrene sulfonate), and X‐ray diffraction showed that the microstructures were amorphous. Thermogravimetric analysis indicated that PPy–PSSA composite films with microstructures had higher thermal stability than pure PPy, PPy‐coated PSSA microspheres, and naphthalene sulfonic acid doped PPy microstructures. Furthermore, PPy–PSSA composite films with microstructures showed cation‐exchange behavior during the redox process in aqueous solutions of sodium dodecyl benzenesulfonate. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 3170–3177, 2004     

Microstructure, distribution and properties of conductive polypyrrole/cellulose fiber composites

Highly intrinsic conductive polypyrrole/cellulose fiber composites (CF) were successfully prepared through in situ chemical oxidation polymerization simply by increasing fiber concentration at the same dosage of pyrrole, oxidant and dopant (based on the weight of dry fiber). FeCl₃ and anthraquinone-2-sulfonic acid sodium salt (AQSNa) were utilized as oxidant and dopant. As fiber concentration increased from 1 % (CF1) to 20 % (CF20), N and S content increased from 0.24 and 0.25 % to 1.24 and 0.89 %, and great increase in the retention of PPy and AQSNa was confirmed by elemental analysis. In addition, on the surface of conductive fiber, PPy of compact fibroid structure was detected instead of interconnected globular structure at higher fiber concentration. Furthermore, scanning transmission electron microscope and X-ray photoelectron spectroscopy (XPS)-depth profile analysis demonstrated denser and more uniformly distributed PPy inside fiber wall for CF20, while PPy tended to deposit on the surface of fiber for CF1. Fourier transform infrared spectroscopy, together with XPS certified that the PPy with longer conjugation length and higher doping level across the conductive fiber was obtained at higher fiber concentration. The doping level for CF10 decreased from 21.55 to 16.39 % with increasing fiber wall thickness, while that of CF20 decreased slightly from 30.73 to 24.10 %. The resulting CF20 showed lowest surface resistivity of 0.433 KΩ/square, as well as improved electro-conductivity stability. The incorporation of more PPy in CF improved the thermal stability.     

Potentiometric Ag+ Sensors Based on Conducting Polymers: A Comparison between Poly(3,4‐ethylenedioxythiophene) and Polypyrrole Doped with Sulfonated Calixarenes

Potentiometric Ag⁺ sensors were prepared by galvanostatic electropolymerization of 3,4‐ethylenedioxythiophene (EDOT) and pyrrole (Py) on glassy carbon electrodes by using sulfonated calixarenes as doping ions. Poly(3,4‐ethylenedioxythiophene) (PEDOT) and polypyrrole (PPy) doped with p‐sulfonic calix[4]arene (C4S), p‐sulfonic calix[6]arene (C6S) and p‐sulfonic calix[8]arene (C8S) were compared. PEDOT and PPy doped with poly(styrene sulfonate) (PSS) were also included for comparison. The analytical performance of the conducting polymer‐based Ag⁺ sensors was studied by potentiometric measurements. All conducting polymer and dopant combinations showed sensitivity and selectivity to Ag⁺ compared to several alkali, alkaline‐earth, and transition‐metal cations. The type of the conducting polymer used for the fabrication of the electrodes was found to have a more significant effect on the selectivity of the electrodes to Ag⁺ than the ring size of the sulfonated calixarenes used as dopants. Selected conducting polymer‐based sensors were studied by cyclic voltammetry (CV) and energy dispersive analysis of X‐rays (EDAX) measurements. Results from the EDAX measurements show that both PEDOT‐ and PPy‐based membranes accumulate silver.     

Conductivity and flame retardancy of polyaniline-deposited functional cellulosic paper doped with organic sulfonic acids

Two kinds of organic sulfonic acids, i.e., p-toluenesulfonic acid (PTSA) and sulfosalicylic acid (SSA), were used as doping acid to prepare the polyaniline-deposited functional cellulosic paper, and both the conductivity and flame retardancy of the functional cellulosic paper were investigated. The results indicated that both the conductivity and the flame retardancy of the paper composite had a close relationship with the incorporation of doping acid. Both the conductivity and the oxygen index (OI) value increased with the increase of the acid concentration. SSA performed much better than PTSA and the inorganic acids studied previously for both the conductivity and the OI value of functional cellulosic paper. The conductivity of the paper doped with SSA was more stable than that of the paper doped with PTSA, and the OI value only decreased about 1 % within 40 days for the functional cellulosic paper doped with the two doping acids. Compared with the polyaniline-deposited paper doped with PTSA, both the much higher doping level and the much smaller and more compact polyaniline particles deposition were probably responsible for the significantly better conductivity and flame retardancy of the polyaniline-deposited paper doped with SSA.     

Electrical conductivity change of polyaniline–dodecyl benzene sulfonic acid complex with temperature

Polyaniline–dodecylbenzene sulfonic acid (PAn–DBSA) complex was thermally treated and its conductivity and structure change were investigated. The conductivity increased linearly from 1.1 × 10⁻⁴ to 3.0 × 10⁻¹ S/cm on thermal heating until 140°C, but decayed above 200°C. The increase was caused by an additional thermal doping resulting from an increasing mobility of undoped dopants. After the thermal doping, the formation of the layered structure of PAn–DBSA is made. The decrease was caused by the thermal decomposition of dopants. The conductivity changes at a high temperature was strongly dependent on the nature of the dopant. The results were confirmed by means of X-ray patterns and Fourier transform infrared spectra obtained in the heating and cooling processes of polyaniline.     

Composites of polypyrrole with conducting and ferromagnetic behaviors

Composites of polypyrrole (PPy) with electrical and ferromagnetic behaviors were synthesized by a chemical method in the presence of p‐dodecylbenzene sulfonic acid sodium salt (NaDS) as a surfactant and dopant. The magnetic properties of the resulting composites showed ferromagnetic behavior, such as high saturated magnetization (M_s = 3.06–43.7 emu/g), and coercive force (H_c = 9–57 Oe). The saturated magnetization linearly increased with increases in the Fe content. No influence of the counterion on this relationship was observed. The conductivity of the composites at room temperature depended on the counterion and doping degree. The highest conductivity of 10⁰ S/cm was achieved under the optimal synthetic conditions. A structural characterization by elemental analysis, Fourier transform infrared, and X‐ray diffraction proved that nanometer‐sized (16–20‐nm) iron oxide (Fe₃O₄) in the composites was responsible for the ferromagnetic behavior of the composites, whereas the high conductivity of the composites contributed to the difficult deprotonation of the doping PPy with DS⁻ counterion in a basic reaction medium. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2734–2739, 2000     

Response of protonic acid‐doped poly(o‐anisidine)/poly(vinyl alcohol) composites to relative humidity and role of dopant anions

Various protonated poly(o‐anisidine) (PoAN)/poly(vinyl alcohol) (PVA) composites were prepared with different types of acids: sulfuric (SA), p‐toluene sulfonic (TSA), camphor sulfonic (CSA), and p‐dodecylbenzene sulfonic (DBSA). In the visible spectrum of each composite in dimethyl sulfoxide, three absorption peaks were observed at 440, 620, and 860 nm. The peaks at 440 and 860 nm, which were enhanced with the increasing content of acid‐doped PoAN in the PVA matrix, were attributed to the radical cation and localized polaron generated in the conducting polymer. However, the peak at 620 nm was ascribed to the emeraldine base (EB) form of PoAN; that is, a portion of the acid was detached from the conducting polymer to form EB‐PoAN and free acid. The linear dependence of the logarithmic electrical conductivity on the variation of humidity, which was observed for all the composites, was caused by the salt–base transition of the conducting polymer, that is, by the movement of free acid between the active sites of the conducting polymer and the strongly bound water existing in PVA, which in turn depended directly on the environmental humidity. The response time of the composites to humidity was shortened with a decrease in the size of the dopant anions: DBSA > CSA > TSA > SA. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 4343–4352, 2000     

Polyaniline doped with different sulfonic acids by in situ doping polymerization

Doped polyaniline (PANI) was synthesized by an “in situ doping polymerization” method in the presence of different sulfonic acids, such as methanesulfonic acid (MSA), p‐methylbenzene sulfonic acid (MBSA), β‐naphthalenesulfonic acid (β‐NSA), α‐naphthalenesulfonic acid (α‐NSA), 1,5‐naphthalenedisulfonic acid (1,5‐NSA), and 2,4‐dinitronaphol‐7‐sulfonate acid (NONSA). Morphology, solubility in m‐cresol, and electrical properties of the doped PANI were measured with the variation of the molecular structure of the selected sulfonic acids. Granular morphology was obtained when the sulfonic acids without a naphthalene ring, such as MSA and MBSA, were used. Regular tubular morphology was obtained only when β‐NSA was used. The tubular morphology can be modified by changing the substitutes, the number, and location of sulfo‐group(SOH) on the naphthalene ring. These results indicated that naphthalene ring in the selected sulfonic acids plays an important role in forming the tubular morphology of the doped PANI by the “in situ doping polymerization” method. All resulting PANI salts were soluble in m‐cresol, with the solubility depending on the molecular structure of the selected dopants. Room‐temperature conductivity for the doped PANI ranges from 10⁻¹ to 10⁰S/cm. Temperature dependence of conductivity shows a semiconductor behavior, and it can be expressed by one dimenson Variable Range Hopping (VRH) model. 1 © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1277–1284, 1999     

Capacitive characteristics of nanocomposites of conducting polypyrrole and functionalized carbon nanotubes: effects of in situ dopant and film thickness

The nanocomposites of functionalized single-walled carbon nanotubes (FSWNTs) and conducting polypyrrole (PPy) doped by FSWNTs, Cl⁻, toluenesulfonate (TOS⁻), and dodecylbenzenesulfonate (DBS⁻), respectively, were electrochemically co-deposited to evaluate their applicability in supercapacitors. The effects of the dopants, with focus on their mass, size and surfactivity, and film thickness on the capacitive characteristics were investigated in 3 M KCl aqueous solution. Although the nanostructure of composites can admittedly improve the capacitive properties, dopant anion was demonstrated to be a more essential factor. The specific capacitance of PPy-TOS/FSWNT nanocomposites was greater than that of pristine PPy/FSWNT nanocomposites and PPy-DBS/FSWNT nanocomposites by ten and 100 times, respectively. Furthermore, PPy-TOS/FSWNT nanocomposites exhibited the lowest dependence of capacitance on the charging–discharging rate and composite thickness due to its high electronic and ionic conductivity resulting from the appropriate doping level and size of TOS^- as well as the synergic effect of PPy-TOS and FSWNTs. In addition, PPy-TOS/FSWNT nanocomposites presented a remarkably stable cycling performance.     

Supra-assembled membranes for optical resolutions

Optical resolutions through self-assembled membranes were carried out by using poly(pyrrole) (PPy) doped with chiral anionic polymers such as poly(L-glutamic acid) or dextran sulfonic acid. Preferential permeations of either L- or D-Tryptophane occurred through the PPy membranes.     

Synthesis of electrically conductive polypyrrole-polystyrene composites using supercritical carbon dioxide: II. Effects of the doping conditions

A polymer composite of polypyrrole (PPy) and polystyrene (PS) was synthesized in this study. Pyrrole was firstly impregnated within the PS substrate where supercritical carbon dioxide (SCCO₂) at 40 °C and 10.5 MPa was used as the solvent. The resulting polymer composite was then soaked in a solution of metallic salt to form an electrically conductive product. Thermal analyses were carried out in this study. Glass transition temperatures from the DSC curves and thermal decomposition temperatures from the TGA curves were observed. These temperatures rise gradually from pure PS, undoped blend to doped composite that indicates blending took place in SCCO₂, and polymerization was proceeding when the pyrrole/PS blend was soaking in the doping solution. Furthermore, various effects of the doping conditions on the conductivity of the PPy/PS composite were investigated. Water and acetonitrile were used as the solvents where the former yielded a higher conductivity of the product. Various doping temperatures were studied and a maximum conductivity was observed at 25 °C. The conductivity also depends on the nature of the oxidant. A bell-shaped profile of the conductivity with respect to the concentration of each oxidant was obtained. The maximum conductivity of the composites with iron compounds as oxidants decreases in the following order of anions: chloride > sulfate > perchloride > nitrate in aqueous solutions. Comparison of the scanning electron microscope results of the composite was presented where chloride and nitrate anions were used as the oxidant. It was found that the composite with higher conductivity has higher bulk density and less porous morphology.     

Electrochemical synthesis of polypyrrole/polyimide conducting composite using a polyamic acid precursor

Conducting polymer/poly(amic acid) composites were synthesized by casting poly(amic acid) (PAAc)film onto the surface of stainless steel followed by electrochemical deposition of polypyrrole. Polypyrrole/polyimide (PPy/PI) composites were also formed by preimidizing the polyamic acid film prior to electrodeposition of PPy. The electrical resistance of the bottom side of PPy/PAAc composite (2.3 Ω cm) was lower than that of the PPy/PI composite (6.4 Ω cm), the thickness of the matrix was the same. A PI matrix was used for electropolymerization of pyrrole. The electrodeposition was investigated by using different current densities. IR spectroscopy revealed interactions between the PAAc and PPy in the composite.     

Synthesis and characterization of polypyrrole dispersions prepared with different dopants

Stable polypyrrole dispersions were prepared by chemical oxidative polymerization of pyrrole in an aqueous medium containing different anionic salts - sodium benzoate, potassium hydrogen phthalate and sodium hydrogen succinate. Results of the elemental analysis and FT-IR spectroscopy confirmed that the anionic salts are incorporated in the conducting polymers and functioned as the dopants. The retardation of pyrrole polymerization was observed when a certain amount of the salt was used as dopant. SEM images of polypyrrole dispersions indicate large spherical particles (150-180nm). The conductivity of polypyrrole composites has also been investigated.     

染料掺杂聚吡咯微纳米管的合成及其影响因素研究

以水溶性染料酸性红G为掺杂剂, 以三氯化铁为氧化剂, 采用无模板自组装方法制备得到了聚吡咯微/纳米管. 利用FTIR, XRD, SEM, TEM对所合成的聚吡咯微/纳米管的结构形貌进行了表征. 结果表明, 搅拌条件下, 酸性红G原位掺杂得到的聚吡咯管直径在100～910 nm之间, 管长大于50 μm. XRD表明所得聚吡咯微/纳米管为无定形态. 研究了反应时间、反应温度、吡咯浓度、掺杂剂与吡咯浓度比、氧化剂滴加速度等对聚吡咯管形貌的影响, 获得了最佳的反应条件.