Cantilever-based photoacoustic detection of carbon dioxide using a fiber-amplified diode laser

A compact and sensitive photoacoustic setup has been developed based on a recently demonstrated cantilever technique. A micromechanical cantilever transducer is attached to a cylindrical photoacoustic cell and the cantilever’s deflection is monitored with a compact Michelson interferometer. A commercial 1-Watt optical fiber amplifier was used to enhance the performance of the system. A normalized sensitivity of 1.4×10^-10 cm^-1 W Hz^-1/2 was achieved in the detection of carbon dioxide at 1572 nm wavelength. Using 34 mW optical power from a DFB diode laser, the noise-equivalent detection limit for carbon dioxide at this wavelength is 4.0 ppm. Employing the fiber amplifier, we improved the sensitivity to yield measurement of sub-ppm concentrations. PACS 42.62.Fi; 42.55.Px; 82.80.Ch     

可调谐半导体激光吸收光谱法监测二氧化碳的通量

含碳温室气体浓度增加所加剧的温室效应是气候变化的重要原因,大面积范围内二氧化碳气体通量的测量对于评价各类陆地生态系统对大气中主要温室气体浓度的贡献具有重要的意义。可调谐半导体激光吸收(TDLAS)光谱技术具有高分辨率、高灵敏度以及快速响应等特点,是痕量气体高灵敏快速监测的新方法。文章以可调谐分布反馈半导体激光器作为光源,通过波长调制方法对1.573μm附近二氧化碳气体某一吸收线的二次谐波信号测量,结合激光分束技术,实现对不同高度层面700多米光程范围内二氧化碳气体浓度的快速在线检测。结合大口径闪烁仪测量出来的莫宁-奥布霍夫长度和特征速度,通过公式计算得到一天内二氧化碳气体的通量在-1.5～2.5mg·(m2·s)-1范围内的波动,突破了目前对近地面痕量气体通量的监测只能提供局地结果的状况,使大面积范围内痕量气体通量的测量成为可能。     

Simultaneous detection of trace gases using multiplexed tunable diode lasers and a photoacoustic cell containing a cantilever microphone

We report what we believe to be a novel demonstration of simultaneous detection of multiple trace gases by near-IR tunable diode laser photoacoustic spectroscopy using a cell containing a cantilever microphone. Simultaneous detection of carbon monoxide (CO), ethyne (C₂H₂), methane (CH₄) and combined carbon monoxide/carbon dioxide (CO+CO₂) in nitrogen-based gas mixtures was achieved by modulation frequency division multiplexing the outputs of four near-IR tunable diode lasers. Normalized noise-equivalent absorption coefficients of 3.4×10^?9, 3.6×10^?9 and 1.4×10^?9 cm^?1?W?Hz^?1/2 were obtained for the simultaneous detection of CO, C₂H₂ and CH₄ at atmospheric pressure. These corresponded to noise-equivalent detection limits of 249.6 ppmv (CO), 1.5 ppmv (C₂H₂) and 293.7 ppmv (CH₄) respectively over a measurement period of 2.6 s at the relevant laser power. The performance of the system was not influenced by the number of lasers deployed, the main source of noise arising from ambient acoustic effects. The results confirm that small-volume photoacoustic cells can be used with low optical power tunable diode lasers for rapid simultaneous detection of trace gases with high sensitivity and specificity.     

Resonant photoacoustic detection of trace gas with DFB diode laser

A resonant photoacoustic detection system based on a low-power distributed feedback diode laser is developed. This sensor has been applied to the detection of acetylene (C₂H₂) using a specifically designed photoacoustic cell operating on its second longitudinal mode. The minimum detectable limit of about 10 parts-per-million volume (SNR=1) is achieved with an average laser power of 3.5 mW at atmospheric pressure, and an integration time constant of 3 ms; thus, the minimum detectable absorption coefficient normalised by power and bandwidth is 4.0×10⁻⁸ W cm⁻¹/√Hz. The optimum operating pressure buffered with N₂ is also investigated. The realisation of our system is described and experimental results are compared with different modulation techniques and other results reported in the literature. A number of issues arising from the conventional use of mechanical chopping of the beam can be effectively suppressed in wavelength modulation PA spectroscopy (WM-PAS) and second harmonic detection.     

可调谐半导体激光吸收光谱遥测二氧化碳通量的研究

可调谐半导体激光吸收光谱技术(TDLAS)具有高分辨率、高灵敏度以及响应时间快等优点.以室温下工作的近红外可调谐半导体激光器为光源,通过波长调制方法对1 578 nm附近CO2气体吸收线的二次谐波信号测量,结合双开放光路技术,实现对不同高度层面700多米长光程范围内CO2气体浓度的快速在线检测.结合大口径闪烁仪测量的莫宁-奥布霍犬长度和特征速度,通过经验公式计算得到CO2气体的通量在-60～60 mg·m-2·s-1范围内波动.实验数据与涡动相关比较表明,两者数据整体变化趋势一致,该方法可以获得较理想的结果.突破了目前对近地面痕量气体通量的监测只能提供局地结果的现象,使大面积范围内痕量气体通量的测量成为可能.     

Breath ammonia detection based on tunable fiber laser photoacoustic spectroscopy

A new detection method for ammonia in high concentration of CO₂ and H₂O is reported, which uses a wavelength modulated photoacoustic spectrometer based on a near-infrared tunable erbium-doped fiber laser in combination with an optical fiber amplifier. The multi-wavelength (1522.44 nm, 1522.94 nm and 1545.05 nm) photoacoustic signal measurement is established to detect multi-spectrum signal in samples. The problem of ammonia detection in high concentration of CO₂ and H₂O is resolved at atmospheric pressure. The minimum detection limit of 16 ppb (signal-to-noise ratio = 1) in simulated breath samples (5.3% CO₂ and 6.2% H₂O (100% relative humidity at 37°C)) is achieved.     

Fiber-optic ring-down spectroscopy using a tunable picosecond gain-switched diode laser

Visible and near-infrared laser light pulses were coupled into two different types of optical fiber cavities. One cavity consisted of a short strand of fiber waveguide that contained two identical fiber Bragg gratings. Another cavity was made using a loop of optical fiber. In either cavity ∼40 ps laser pulses, which were generated using a custom-built gain-switched diode laser, circulated for a large number of round trips. The optical loss of either cavity was determined from the ring-down times. Cavity ring-down spectroscopy was performed on 200 pL volumes of liquid samples that were injected into the cavities using a 100 μm gap in the fiber loop. A detection limit of 20 ppm of methylene blue dye in aqueous solution, corresponding to a minimum absorptivity of εC<6 cm^-1, was realized. PACS 42.62.Fi; 42.81.-i     

Application of a broadband blue laser diode to trace NO2 detection using off-beam quartz-enhanced photoacoustic spectroscopy

We applied for the first time, to our knowledge, broadband off-beam quartz-enhanced photoacoustic spectroscopy (BB-OB-QEPAS) to trace NO2 detection using a broadband blue laser diode centered at 450?nm. A detection limit of 18?ppbv (parts in 10(9) by volume) for NO2 in N2 at atmospheric pressure was achieved with an average laser power of 7?mW at a 1?s integration time, which corresponds to a 1?σ normalized noise equivalent absorption coefficient of 4.1×10(-9) cm(-1)?W=Hz(1=2). An Allan variance analysis was performed to investigate the long-term stability of the BB-OB-QEPAS-based NO2 sensor.     

Intracavity photoacoustic gas detection with an external cavity diode laser

The first use of an external cavity diode-laser light source in combination with a photoacoustic detector for high-sensitivity gas detection is described. This combined system is applicable for detecting gases with absorption coefficients as low as 5 x 10^–8 cm^–1 by operating the photoacoustic cell in an intracavity mode. Measurements were made on the 1.13 m absorption lines of water vapour. For quantitative measurements, it was found to be necessary to introduce a reference cell into the system.     

Application of a widely electrically tunable diode laser to chemical gas sensing with quartz-enhanced photoacoustic spectroscopy

A near-infrared diode laser with sample-grating distributed Bragg reflectors was used as a widely tunable spectroscopic source for multispecies chemical sensing. Quartz-enhanced photoacoustic spectroscopy was utilized to obtain high absorption sensitivity in a compact gas cell. CO2, H2O C2H2, and NH3 were monitored. A noise equivalent sensitivity of 8 x 10(-9) cm(-1) W(-1) Hz(-1/2)for NH3 detection was achieved, which corresponds to a NH3 mixing ratio of 4.4 parts in 10(6) by volume (ppmv) with a 1-s time constant and available 5.2-mW optical power in the gas cell.     

Non-contact detection of explosives by means of a tunable diode laser spectroscopy

As explosives are unstable, their decay products may be targeted for detection by means of tunable diode laser spectroscopy (TDLS). A model in which an explosive is placed inside an envelope with a hole in it has been studied. It has been shown that outside the envelope the concentration of the decay products may exceed that of the vapors of an explosive, by several orders. Decay products of explosives have been investigated using Fourier-transform spectrometry and TDLS. The following decay products have been identified: NO, N₂O, CO, NH₃. Analysis of the temperature dependencies of their occurrence rates has allowed estimation of the activation energies, which appear to be close to 1 eV. An experimental model of the diode laser spectrometer designed for noncontact detection of explosives has been developed. The possibility of such detection has been demonstrated experimentally. PACS 42.62.Fi; 07.07.Df; 42.55.Px     

Cavity-enhanced absorption: detection of nitrogen dioxide and iodine monoxide using a violet laser diode

We present an application of cavity-enhanced absorption spectroscopy with an off-axis alignment of the cavity formed by two spherical mirrors and with time integration of the cavity-output intensity for detection of nitrogen dioxide (NO₂) and iodine monoxide (IO) radicals using a violet laser diode at λ=404.278 nm. A noise-equivalent (1σ≡ root-mean-square variation of the signal) fractional absorption for one optical pass of 4.5×10^-8 was demonstrated with a mirror reflectivity of ∼0.99925, a cavity length of 0.22 m and a lock-in-amplifier time constant of 3 s. Noise-equivalent detection sensitivities towards nitrogen dioxide of 1.8×10¹⁰ molecule cm^-3 and towards the IO radical of 3.3×10⁹ molecule cm^-3 were achieved in flow tubes with an inner diameter of 4 cm for a lock-in-amplifier time constant of 3 s. Alkyl peroxy radicals were detected using chemical titration with excess nitric oxide (RO₂+NO→RO+NO₂). Measurement of oxygen-atom concentrations was accomplished by determining the depletion of NO₂ in the reaction NO₂+O→NO+O₂. Noise-equivalent concentrations of alkyl peroxy radicals and oxygen atoms were 3×10¹⁰ molecule cm^-3 in the discharge-flow-tube experiments. Received: 4 February 2003 / Revised version: 10 March 2003 / Published online: 12 May 2003 RID="*" ID="*"Corresponding author. Fax: +44-1865/275-410, E-mail: vlk@physchem.ox.ac.uk     

An all-solid-state tunable 214.5-nm continuous-wave light source by using two-stage frequency doubling of a diode laser

3 and β-BaB₂O₄ crystals. The power of the generated 214.5-nm light amounts to more than 100 μW. This light source will be used for laser cooling of Cd⁺ ions. Received: 4 August 1997/Revised version: 28 October 1997     

Detection of sulphur dioxide at,and below,the part per billion level using a tunable diode laser

A laser absorption spectrometer is described which employs a wavelength tunable diode laser in conjunction with a multipass White cell. The instrument uses absorption lines in the ₃ band of SO₂ to monitor atmospheric SO₂ concentrations with sensitivities as high as 0.2 parts per billion (ppb) in a laboratory system. A portable instrument with a fast response time and a sensitivity of 1 ppb is described, and the development of a highly practical field instrument, based on pyroelectric detectors, is discussed.Work supported by the Department of National Health and Welfare, Environment Canada, Ontario Ministry of the Environment, and Atmospheric Service, Environment Canada.     

Electronically tunable external-cavity laser diode

We present a new concept for an electronically tunable diode laser. It is based on an external-cavity configuration with simultaneous feedback and intracavity spatial separation of the laser's spectral components. The electronical tunability is achieved by insertion of a liquid-crystal array as an electronically controlled aperture into the region of spatial separation of the spectral components. Wavelength tunability without mechanical movement over a range of 10 nm and two-color operation are demonstrated with a 670-nm laser diode.     

Sensitive harmonic detection of ammonia trace using a compact photoacoustic resonator at double-pass configuration and a wavelength-modulated distributed feedback diode laser

A sensitive detection of ammonia in parts per billion by volume is described. The system based on photoacoustic spectroscopy (PAS) consists of distributed feedback laser diode emitting near 1,531.7 nm and a compact PA cell at double-pass configuration. In order to optimize the signal background ratio of the system, two types of modulations were tested, amplitude and wavelength modulations (WM). Using a digital lock-in amplifier, the 1f and 2f detection in WM could be investigated. A detection limit of 470 parts per million by volume could be achieved at WM-2f. In the sense of quantifing the adsorption–desorption process, the response time of the system and detection accuracy was performed in different flows. Response times between 10 and 49 s, depending on the flow rate, were obtained which enables the PA system to measure low concentrations of ammonia with high accuracy in real time.     

Cost-effective tunable fiber laser based on self-seeded Fabry-Perot laser diode using a Sagnac loop reflector

We propose and demonstrate a simple configuration of wavelength-tunable fiber laser made up of a tunable band-pass filter, a Sagnac loop refiector, and a Fabry-Perot laser diode. Based on the self-seeded operation, the proposed fiber laser can obtain a single-longitudinal-mode output in the wavelength tuning range of 1544.69–1563.39 nm with tuning step of 1.34 nm. The performances of output power （-9 dBm）, optical side-mode suppression ratio （ 65.5 dB）, and power and wavelength stabilities are well exhibited.     

Influence of laser intensity in second-harmonic detection with tunable diode laser multi-pass absorption spectroscopy

Tunable diode laser absorption spectroscopy （TDLAS） has been widely employed in atmospheric trace gases detection. The ratio of the second-harmonic signal to the intensity of laser beam incident to the multi-pass cell is proved to be proportional to the product of the path length and the gas concentration under any condition. A new calibration method based on this relation in TDLAS system for the measurement of trace gas concentration is proposed for the first time. The detection limit and the sensitivity of the system are below 110 and 31ppbv （parts-per-billion in volume）, respectively.