Adsorptive stripping measurements of germanium(IV) in the presence of pyrogallol

The adsorptive stripping voltammetric determination of germanium(IV) based on the adsorptive accumulation of the germanium(IV)-pyrogallol complex on a hanging mercury drop electrode is reported. The reduction current of the adsorbed germanium complex is measured by differential-pulse cathodic stripping voltammetry. The peak potential is at -0.42 V vs. Ag AgCl (saturated KCL). The effects of various parameters (ligand concentration, supporting electrolytic composition and concentration, accumulation potential and collection time) on the response are discussed. With controlled accumulation for 3 min, the detection limit is 1.2 x 10(-9) M germanium. The relative standard deviation (at 1.2 x 10(-8) M germanium) is 3.6%. Possible interferences are evaluated. The applicability of the method to the determination of germanium(IV) in ore samples was also successfully carried out.     

Speciation of antimony by adsorptive stripping voltammetry using pyrogallol

This paper describes a new procedure for the determination of Sb (III) and Sb (V) by differential pulse adsorptive stripping voltammetry (DPAdSV) using pyrogallol as a complexing agent. The selection of the experimental conditions was made using experimental design methodology. The detection limits obtained were 1.03 × 10⁻¹⁰ and 9.48 × 10⁻⁹ mol dm⁻³ for Sb (III) and Sb (V), respectively.In order to carry out the simultaneously determination of both antimony species a partial least squares regression (PLS) is employed to resolve the voltammetric signals from mixtures of Sb (III) and Sb (V) in the presence of pyrogallol. The relative error in absolute value is less than 0.5% when concentrations of several mixtures are calculated. Moreover, the solution is analyzed for any possible effects of foreign ions. The procedure is successfully applied to the speciation of antimony in pharmaceutical preparations and water samples.     

An Electrochemical Sensor Based on Silver Nanoparticles‐Benzalkonium Chloride for the Voltammetric Determination of Antiviral Drug Tenofovir

A simple voltammetric nanosensor was described for the highly sensitive determination of antiviral drug Tenofovir. The benzalkonium chloride and silver nanoparticles were associated to build a nanosensor on glassy carbon electrode. Surface characterictics were achieved using scanning electron microscopic technique. The voltammetric measurements were performed in pH range between 1.0 and 10.0 using cyclic, adsorptive stripping differential pulse and adsorptive stripping square wave voltammetry. The linear dependence of the peak current on the square root of scan rates and the slope value (0.770) demonstrated that the oxidation of tenofovir is a mix diffusion‐adsorption controlled process in pH 5.70 acetate buffer. The linearity range was found to be 6.0×10⁻⁸–1.0×10⁻⁶ M, and nanosensor displayed an excellent detection limit of 2.39×10⁻⁹ M by square wave adsorptive stripping voltammetry. The developed nanosensor was successfully applied for the determination of Tenofovir in pharmaceutical dosage form. Moreover, the voltammetric oxidation pathway of tenofovir was also investigated at bare glassy carbon electrode comparing with some possible model compounds (Adenine and Adefovir).     

Electro-oxidation of herbicide halosulfuron methyl on glassy carbon electrode and applications

Halosulfuron methyl, a fast-acting herbicide and is absorbed into leaf tissue within 1-2 days and translocated through the vascular system, interrupting amino acid production within the plant, can be detected using glassy carbon electrode the technique of adsorptive stripping voltammetry. The adsorptive stripping voltammetric behavior of halosulfuron methyl was investigated in pH range 1.0-10.0. Halosulfuron methyl was irreversibly oxidized at a glassy carbon electrode. Electrochemical techniques including adsorptive stripping voltammetry and cyclic voltammetry were employed to study the oxidation mechanism. The experimental parameters such as the accumulation potential, accumulation time and frequency were optimized. The linear range, detection limit and quantification for halosulfuron methyl were evaluated by adsorptive stripping voltammetry. Under the optimized conditions, the peak current is linear to halosulfuron methyl concentration in the range 4.1-50.0 μg mL⁻¹. Limit of detection and limit of quantification were 1.23 and 4.10 μg mL⁻¹, respectively. The interference of inorganic species and other some pesticides on the voltammetric response have been studied. The applicability to spiked soil and natural water was described and the recoveries for the standards added are 103.8% and 108.2%, respectively. The method is successfully applied for the determination of halosulfuron methyl in commercial formulation.     

Differential pulse and square-wave cathodic stripping voltammetry of xanthine and xanthosine at a mercury electrode.

The surface activity of xanthine (Xan) and xanthosine (Xano) at a hanging mercury drop electrode (HMDE) was studied using out-of-phase ac and cyclic dc voltammetry. The results show that Xan and Xano were strongly adsorbed and chemically interacted with the charged mercury surface, which is the prerequisite step for applying the cathodic adsorptive stripping voltammetric determination of such biologically important compounds. Differential pulse cathodic adsorptive stripping voltammetry (DPCASV) and square-wave cathodic adsorptive stripping voltammetry (SWCASV) were applied for the ultratrace determination of Xan and Xano compounds. Moreover, a rapid and sensitive controlled adsorptive accumulation of Cu(II) complexes of both compounds provided the basis of a direct stripping voltammetric determination of such compounds to submicromolar and nanomolar levels. Operational and solution conditions for the quantitative ultratrace determination of Xan and Xano were optimized in absence and presence of Cu(II). The calibration curve data were subjected to least-squares refinements. The effects of several types of inorganic and organic interfering species on the determination of Xan or Xano were considered.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily Received: 10 July 1997 / Revised: 1 April 1998 / Accepted: 6 April 1998     

Review of adsorptive stripping voltammetric methods for cobalt determination in the presence of a zinc matrix

Different polarographic and voltammetric methods for the determination of Co in the presence of a large excess of zinc are reviewed. Adsorptive stripping voltammetry with in-situ matrix exchange and catalytic adsorptive stripping voltammetric methods are recommended for monitoring Co traces in zinc plant electrolyte. The principles of the catalytic adsorptive stripping voltammetric methods for Co determination are presented. The correct selection of the investigated supporting electrolytes, enabling the monitoring of Co traces in a zinc plant electrolyte by means of catalytic adsorptive methods is also discussed. The catalytic adsorptive voltammetric procedures offer the possibility of the determination of Co or Co and Ni traces in metallic zinc and zinc salts.     

Square-wave cathodic adsorptive stripping voltammetric determination of trace amounts of 2-mercaptobenzimidazole in water samples

A sensitive, simple and reproducible square-wave cathodic adsorptive stripping voltammetric method is developed for the determination of 2-mercaptobenzimidazole (MBIM) in different water samples using a static mercury drop electrode (SMDE) as a working electrode. The solution conditions and instrumental parameters were optimized for the determination of MBIM by square-wave cathodic adsorptive stripping voltammetry. This method is based on a sensitive adsorptive reduction peak of the MBIM at ?0.532 V vs. Ag/AgCl reference electrode in a Britton-Robinson buffer at pH 10.0. The linear concentration range was 20–600 ng ml^?1 when using 0.0 V as the accumulation potential. The detection limit of the method was calculated to be 8.41 ng ml^?1. The precision was excellent with relative standard deviations (n = 20) of 2.30%, 1.71%, 2.25% and 1.33% at MBIM concentrations of 40, 90, 200 and 500 ng ml^?1, respectively. The proposed voltammetric method is used for the determination of MBIM in different spiked water samples.     

Anodic stripping voltammetry of germanium at the hanging mercury drop electrode

The Ge(IV)—Ge(0) system was investigated by cyclic and stripping voltammetry at HMDE in acidic pyrogallol medium and in phosphate, borate and carbonate buffers. It was found that germanium electrodeposited from dilute Ge(IV) solutions dissolved anodically forming two peaks corresponding to the oxidation of the unstable homogeneous and stable heterogeneous amalgams. Both peaks can be exploited analytically for the determination of traces of germanium but due to the complex nature of the germanium amalgam the sensitivity and reproducibility of the determinations are lower compared to the results obtained for metals well-soluble in mercury.     

Determination of the pesticide Chlorpyrifos by cathodic adsorptive stripping voltammetry

The adsorption behavior and differential pulse cathodic adsorptive stripping voltammetry of the pesticide Chlorpyrifos (CP) were investigated at the hanging mercury drop electrode (HMDE). The pesticide was accumulated at the HMDE and a well-defined stripping peak was obtained at –1.2 V vs Ag/AgCl electrode at pH 7.50. A voltammetric procedure was developed for the trace determination of Chlorpyrifos using differential pulse cathodic adsorptive stripping voltammetry (DP-CASV). The optimum working conditions for the determination of the compound were established. The peak current was linear over the concentration range 9.90 × 10^–8– 5.96 × 10^–7 mol/L of Chlorpyrifos. The influence of diverse ions and some other pesticides was investigated. The analysis of Chlorpyrifos in commercial formulations and treated waste water was carried out satisfactorily     

Square-wave adsorptive stripping voltammetric approaches at two in situ modified electrodes as first analytical methods for the quantitative determination of a new anticancer drug candidate

The two adsorptive stripping voltammetric approaches for detection and quantitative determination of diethyl (2E)-2-{(2E)-[1-(4-methylphenyl)imidazolidin-2-ylidene]hydrazinylidene}butanedioate (DIB)—a novel molecule of medical importance—using two sensitive sensors based on modified glassy carbon electrodes as reusable sensors, were developed for the first time. The proposed electrochemical methods are based on adsorptive/reductive behaviour of DIB at two modified carbonic electrodes: a bismuth film-modified glassy carbon electrode (BiF/GCE) and a lead film-modified glassy carbon electrode (PbF/GCE). The electron gain mechanism for the electrochemical reduction of DIB on both developed sensors was proposed for the first time. To achieve the highest sensitivity in adsorptive stripping determinations, various experimental variables (e.g. the composition and pH of the supporting electrolytes, deposition conditions of bismuth and lead films, concentrations of plating solutions, accumulation times and potentials of DIB, etc.) were extensively examined. The comparison of validation parameters obtained during the determination of DIB at two sensors was presented. The excellent linear correlation was found between the monitored adsorptive stripping voltammetric peak current and the DIB concentration in the range of 15–600 μg L⁻¹ at an accumulation time of 30 s (with LOD = 4.2 μg L⁻¹ and LOQ = 14.0 μg L⁻¹) using the BiF/GCE as a sensor. Furthermore, the excellent linear relationship was confirmed between the monitored adsorptive stripping voltammetric peak current and the DIB concentration in the range of 9–900 μg L⁻¹ at an accumulation time of 10 s (with better LOD = 1.5 μg L⁻¹ and LOQ = 5.0 μg L⁻¹), employing the PbF/GCE as a sensor. The two optimized adsorptive stripping voltammetric approaches—as facile, sensitive, reliable and inexpensive—were successfully used as first methods for the quantitative analysis of a novel anticancer agent (DIB) in its pure pharmaceutically acceptable form. However, the practical applicability of square-wave adsorptive stripping voltammetric determination of the electroactive DIB molecule at a PbF/GCE, as the modified electrode of higher sensitivity, was presented after its successful solid phase extraction from a real serum sample.

     

A novel catalytic adsorptive stripping voltammetric method for the determination of germanium ultratraces in the presence of chloranilic acid and the V(IV)·HEDTA complex

A novel, sensitive catalytic adsorptive stripping voltammetric procedure which can be used to determine trace amounts of germanium is described. The method is based on the interfacial accumulation of the complex formed by Ge(IV) and the product of the reduction of chloranilic acid on the hanging mercury drop electrode or the renewable silver amalgam film electrode, and its subsequent reduction from the adsorbed state followed by the catalytic action of the V(IV)·HEDTA complex. The presence of V(IV)·HEDTA greatly enhances the adsorptive stripping response of Ge. The reduction of the Ge(IV) in the presence of chloranilic acid and V(IV)·HEDTA was investigated in detail and the effects of pH, electrolyte composition, and instrumental parameters were studied. Under optimal conditions, the catalytic peak current of germanium exhibited good linearity for Ge(IV) concentrations in the range of 0.75–60 nM (for 60 s of accumulation at −0.1 V, r² = 0.995) and a low limit of detection (LOD = 0.085 nM). The procedure was successfully applied to determine Ge in water samples.

     

Square-wave adsorptive stripping voltammetric determination of antihypertensive agent telmisartan in tablets and its application to human plasma

The adsorptive stripping voltammetry of telmisartan was investigated with a hanging mercury drop electrode. This compound produced a catalytic hydrogen wave at ?1.5 V in Britton Robinson buffer of pH 10.38, and the peak current increased with adsorptive accumulation at the electrode. Adsorptive stripping voltammetry with the catalytic hydrogen wave could provide a sensitive novel method for the determination of telmisartan. Various chemical and instrumental parameters affecting the monitored electroanalytical response were investigated and optimized for telmisartan determination. Under these optimized conditions the square-wave adsorptive stripping voltammetric (SW-AdSV) peak current showed a linear dependence on drug concentration over the range 0.05–3.00 μg/mL (1 × 10^?7?6 × 10^?6 M) (r = 0.999) with accumulation for 120 s at ?1.0 V vs. Ag/AgCl. The proposed electrochemical procedure was successfully applied for the determination of telmisartan in pharmaceutical tablets and human plasma. The results of the developed SW-AdSV method were comparable with those obtained by reported analytical procedures.     

Characteristics of Voltammetric Determination and Speciation of Chromium – A Review

This article reviews the voltammetric methods of chromium determination, including adsorptive and catalytic adsorptive stripping voltammetry at liquid mercury, metallic films, and modified carbon paste electrodes. The principle applications of the catalytic adsorptive stripping voltammetric method of chromium(VI) determination in the presence of DTPA and nitrate, most useful in the analysis of chromium traces and its speciation, is presented in detail. Special emphasis is put on the presentation and characterization of the voltammetric procedures which make it possible to conduction speciation studies of chromium(VI) in the presence of a great excess of chromium(III) and surfactants. This survey is based on 173 articles.     

Catalytic adsorptive stripping voltammetry determination of ultra trace amount of molybdenum using factorial design for optimization

A highly sensitive procedure is presented for the determination of ultra-trace concentration of molybdenum by catalytic adsorptive stripping voltammetry. The method is based on adsorptive accumulation of the molybdenum (Mo)-pyrocatechol violet (PCV) complex on to a hanging mercury drop electrode, followed by reduction of the adsorbed species by voltammetric scan using differential pulse modulation. The reduction current is enhanced catalytically by chlorate. The influence of variables was completely studied by factorial design analysis. Optimum analytical conditions for the determination of molybdenum were established. Molybdenum can be determined in the range 1.0 × 10⁻³-100.0 ng ml⁻¹ with a limit of detection of 0.2 pg ml⁻¹. The influence of potential interfering ions on the determination of molybdenum was studied. The procedure was applied to the determination of molybdenum in mineral water and some analytical grade substances with satisfactory results.     

Application of an in situ plated lead film electrode to the analysis of testosterone by adsorptive stripping voltammetry

Adsorptive stripping voltammetry is a very sensitive and selective method for determination of drugs and organic substances in biological fluids. We have shown that determination of testosterone by adsorptive stripping voltammetry is possible using a lead film electrode. The lead film plating process and accumulation of testosterone were performed simultaneously from an acetate buffer solution of pH = 5.2 at a potential of −1.1 V. The measurements were carried out in undeaerated solutions. The detection limit was 9 × 10⁻⁹ mol L⁻¹ for an accumulation time of 120 s; the relative standard deviation for 1 × 10⁻⁷ mol L⁻¹ testosterone was 3.8%. The proposed voltammetric procedure for determination of testosterone could be applied to its determination in a pharmaceutical preparation and human urine samples directly without any separation steps.     

Cathodic adsorptive stripping square-wave voltammetry of the anti-inflammatory drug meloxicam

The adsorptive behavior of the anti-inflammatory drug meloxicam was studied by cyclic, differentia-pulse and square-wave voltammetry on a hanging mercury drop electrode (HMDE). The drug was accumulated at HMDE and a well-defined stripping peak current was obtained at -1.42 V vs. Ag/AgCl (saturated KCl) electrode in acetate buffer solution (pH 5.0). A voltammetric procedure was developed for the determination of meloxicam using square-wave cathodic adsorptive stripping voltammetry (SW-CASV). The optimum working conditions for the determination of the drug were established. The analysis of meloxicam in human plasma was carried out satisfactorily.     

Stripping Voltammetry of Cerium(IIl) with a Chemically Modified Carbon Paste Electrode Containing Functionalized Nanoporous Silica Gel

This research introduces the design of an adsorptive stripping voltammetric method for the cerium(III) determination at a carbon paste electrode, chemically modified with dipyridyl‐functionalized nanoporous silica gel (DPNSG‐CPE). The electroanalytical procedure comprised two steps: the Ce(III) chemical accumulation at ?200 mV followed by the electrochemical detection of the Ce(III)/dipyridyl complex, using anodic stripping voltammetry. The factors, influencing the adsorptive stripping performance, were optimized including the modifier quantity in the paste, the electrolyte concentrations, the solution pH and the accumulation potential or time. The resulting electrode demonstrated a linear response over a wide range of Ce(III) concentration (1.0–28 ng mL^?1). The precision for seven determinations of 4 and 10 ng mL^?1 Ce(III) was 3.2% and 2.5% (relative standard deviation), respectively. The prepared electrode was used for the cerium determination in real samples and very good recovery results were obtained.     

Catalytic Adsorptive Stripping Voltammetric Determination of Cobalt and Nickel as Their α‐Furil Dioxime Complexes

The exploitation of the catalytic‐adsorptive effect in the Co(II)‐dioxime‐nitrite systems provides a significant increase of the Co adsorptive stripping voltammetric response and subsequently the influence of the interfering elements such as Ni and Zn is strongly diminished. The purpose of the present paper was to study voltammetric properties of Co and Ni in a supporting electrolyte containing ammonia buffer, α‐furil dioxime in the absence and in the presence of nitrite, by differential pulse polarography and adsorptive stripping voltammetry. Results of detailed studies aimed at optimizing the analytical parameters for simultaneous catalytic adsorptive stripping voltammetric determination of Co and Ni in the form of complexes with α‐furil dioxime in the presence of Zn matrix are presented. In the supporting electrolyte of composition 0.1 M NH₄Cl, 0.5 M NH₃, 4×10^?5 M αFD, 0.5 M NaNO₂ the linearity range amounts from 0.03 to 2.4 μg/L for Co and from 0.3 to 9 μg/L for Ni for 20 s of accumulation. The method enables the determination of Co and Ni in the presence of a great excess of Zn with the detection limit equal to 0.02 μg/L Co and 0.2 μg/L Ni obtained for a 20 s accumulation time.     

Catalytic adsorptive stripping voltammetry versus electrothermal atomic absorption spectrometry in the determination of trace cobalt and chromium in human urine

Two methods of the determination of cobalt and chromium in human urine of non-occupationally exposed populations—highly sensitive catalytic adsorptive stripping voltammetry (CAdSV) and electrothermal atomic absorption spectrometry (ET-AAS)—are evaluated and compared. The CAdSV methods are based on adsorptive accumulation of a cobalt-nioxime (1,2-cyclohexanedione dioxime) or a chromium-DTPA (diethylenetriammine-N,N,N′,N″,N″-pentaacetic acid) complexes on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of the catalytic reduction current of the adsorbed complex in the presence of sodium nitrite in case of cobalt or in the presence of sodium nitrate in case of chromium determination. In the CAdSV procedure UV-photolysis was used for the sample pre-treatment; the ET-AAS determination did not require any separate preliminary decomposition of the analyte urine samples. The accuracy of the procedures was checked by the analysis of commercially available quality control urine samples. The detection limits (3σ) were 0.13 μg l⁻¹ for Co and 0.18 μg l⁻¹ for Cr in ET-AAS determination and 0.007 μg l⁻¹ for Co and 0.002 μg l⁻¹ for Cr in CAdSV measurements. Precision (R.S.D.) was less than 5% for both methods. The study has shown that the CAdSV is a more reliable and sensitive technique for the determination of very low cobalt and chromium contents in urine, the detection of which is not possible when using the AAS technique.