Determination of organophosphate flame retardants and plasticizers in sediment samples using microwave-assisted extraction and gas chromatography with inductively coupled plasma mass spectrometry

A procedure for the determination of 10 organophosphates, used as flame retardants and plasticizers, in sediment samples is presented. Microwave-assisted extraction (MAE) and gas chromatography with inductively coupled plasma mass spectrometry (GC-ICP-MS) were used for sample preparation and analytes determination, respectively. Influence of different variables on the performance of extraction and determination processes is thoroughly discussed. Temperature, type and amount of organic solvent showed a major effect on the yield of MAE. Regarding GC-ICP-MS detection, the combination of pulsed splitless injection with low radio frequency (rf) power, hard extraction conditions (referred to lens voltage) and addition of nitrogen (0.03 L min⁻¹) to the argon plasma provided the best sensitivity. Under final working conditions, recoveries between 78% and 105%, for samples spiked at different concentration levels, and limits of quantification from 2 to 4 ng g⁻¹ were achieved. Analysis of unspiked sediments confirmed the excellent selectivity of the proposed method for real-life polluted sample analysis.     

Pressurized liquid extraction of organophosphate triesters from sediment samples using aqueous solutions

A novel procedure for the extraction of seven organophosphate triesters (OPs), used as flame retardants and plasticizers, from sediment samples has been developed. It is based on the pressurized liquid extraction of the analytes with aqueous solutions, combined with a further concentration step using solid-phase extraction (SPE) and followed by gas chromatography coupled to mass spectrometry (GC-MS) determination. The effects of different variables on the yield and selectivity of the sample preparation process are systematically evaluated. The optimal responses were observed extracting 2 g of sediment with a water:acetonitrile (75:25) solution at 90 °C and 1500 psi for 5 min. The obtained extract was made up to 200 mL with ultrapure water and passed through an OASIS HLB, 60 mg cartridge. Analytes were recovered with 2 mL of ethyl acetate and this extract concentrated to a lower volume, ca. 0.2 mL. Recoveries of the proposed extraction method ranged from 77 to 111%, with relative standard deviations below 10%, for spiked river and marine sediment samples with total carbon contents (TC) up to 4.0%. The limits of quantification (LOQs) of the method varied between 0.5 and 5 ng g⁻¹. Analysis of non-spiked sediment samples revealed the presence of low levels for some of the investigated species, with the highest concentration (47 ng g⁻¹) corresponding to tris(2-chloroethyl) phosphate (TCEP).     

Dispersive liquid–liquid microextraction of five chlorophenols in water samples followed by determination using capillary electrophoresis

Dispersive liquid–liquid microextraction (DLLME) coupled with CE was developed for simultaneous determination of five types of chlorophenols (CPs), namely 2‐chlorophenol (2‐CP), 4‐chlorophenol (4‐CP), 2,4‐dichlorophenol (2,4‐DCP), 2,6‐dichlorophenol (2,6‐DCP), and 2,4,6‐trichlorophenol (2,4,6‐TCP) in water samples. Several parameters affecting DLLME and CE conditions were systematically investigated. Under the optimized DLLME‐CE conditions, the five CPs were separated completely within 7.5 min and good enrichment factors were obtained of 40, 193, 102, 15, and 107 for 4‐CP, 2,4,6‐TCP, 2,4‐DCP, 2‐CP, and 2,6‐DCP, respectively. Good linearity was attained in the range of 1–200 μg/L for 2,4,6‐TCP, 2,4‐DCP, 2−300 μg/L for 4‐CP and 2‐CP, and 1−300 μg/L for 2,6‐DCP, with correlation coefficients (r) over 0.99. The LOD (S/N = 3) and the LOQ (S/N = 10) were 0.31−0.75 μg/L and 1.01−2.43 μg/L, respectively. Recoveries ranging from 60.85 to 112.36% were obtained with tap, lake, and river water spiked at three concentration levels and the RSDs (for n = 3) were 1.31–11.38%. With the characteristics of simplicity, cost‐saving, and environmental friendliness, the developed DLLME‐CE method proved to be potentially applicable for the rapid, sensitive, and simultaneous determination of trace CPs in complicated water samples.     

Miniaturized dynamic liquid-liquid extraction of organophosphate triesters from blood plasma using the hollow fibre-based XT-tube extractor

A miniaturized liquid–liquid extractor for bioanalytical sample preparation is described. The extractor consists of a polypropylene hollow fibre mounted inside polytetrafluoroethylene (PTFE) tubing by means of a cross (X) connector and a tee (T) connector. All parts are commercially available, inexpensive, and easily assembled. The aqueous sample, injected into a carrier flow, is pumped along the outside of the fibre and the organic phase, which also wets the pores of the hollow fibre wall, is pumped inside. Eight organophosphate triester (OPE) plasticisers/flame retardants were extracted from 50 µL spiked blood plasma that had been mixed with 50 µL formic acid to denature plasma proteins. The organic phase was a mixture of hexane and methyl tert-butyl ether (MTBE). A high concentration of formic acid in the sample and of MTBE in the organic phase had positive effects on the recovery of some OPE. When investigating the recovery as a function of extraction time it was found that the extraction reached a maximum after 10 min, at a flow-rate of 15 µL min^–1. Recoveries varied between 40 and 80% with RSD around 4% for most compounds. The whole 150-µL extract was injected into a GC–MS system equipped with a programmed-temperature vaporization (PTV) injector. With the MS in selected-ion monitoring (SIM) mode, the LOD for triphenyl phosphate and 2-ethylhexyl diphenyl phosphate were 0.3 and 0.2 ng mL^–1, respectively. More than 40 plasma extractions were performed with the same fibre without any detectable change in extraction efficiency.     

Development of a dispersive liquid-liquid microextraction method for organophosphorus flame retardants and plastizicers determination in water samples

A fast, inexpensive and efficient sample preparation method for the determination of 10 organophosphorus compounds in water samples is presented. Analytes were extracted using the dispersive liquid-liquid microextraction (DLLME) technique and determined by gas chromatography with nitrogen-phosphorus detection (GC-NPD). The influence of several variables (e.g. type and volume of dispersant and extraction solvents, ionic strength, shaking time and mode, etc.) on the performance of the sample preparation step was carefully evaluated. Under final working conditions, 1 mL of acetone containing a 2% of 1,1,1-trichloroethane (20 microL) was added to 10 mL of water with 20% of sodium chloride. The ternary mixture was centrifuged at 3500 rpm to allow phase separation. After removing the aqueous supernatant, an aliquot of the settled extract was injected in the GC-NPD system. Under the above conditions, the method provided enrichment factors between 190 and 830 times (depending on the considered compound), relative standard deviations below 10%, except for tris(2-ethylhexyl) phosphate (TEHP), and quantification limits between 0.01 and 0.08 ng/mL. Matrix effects were assessed using different water samples, and accuracy was evaluated by comparison with solid-phase microextraction.     

Development of an ultra-high-performance liquid chromatography-tandem mass spectrometry method for high throughput determination of organophosphorus flame retardants in environmental water

Widely used as flame retardants, organophosphate esters (OPEs) are now broadly present in the indoor and outdoor environments. Currently available liquid chromatography-tandem mass spectrometry (LC-MS/MS) methods share some drawbacks with gas chromatography (GC) methods, including time consuming, limited target OPEs, incomplete separation capability for some OPEs and low throughput. In this study, a fast and high throughput LC-MS/MS method was developed. For the first time, all the twelve OPEs that have been studied in literature, ranging from the very polar and volatile trimethyl phosphate to the very hydrophobic and non-volatile tris(2-ethylhexyl) phosphate, were separated within 11 min. Different from previous studies, we found that the blank contamination was mainly from organic mobile phase rather than the enrichment process, and it can be efficiently eliminated by using acetonitrile rather than methanol as the organic phase of the mobile phase. The signal to noise ratio (S/N) was significantly improved by using 0.1% formic acid as an organic modifier. The method exhibited high throughput and sensitivity and can baseline separate 11 of the 12 OPEs studied within 11 min with LOQs ranging from 2 to 6 ng/L. The relative standard deviations were in the range of 2-10%. For both reagent water and river water, the spiked recoveries of OPEs ranged from 70 to 110%, except for the very polar and volatile trimethyl phosphate that has recovery below 10%. The developed procedure was successfully applied to study the OPE contamination of the Songhua River, and it was found that all the target OPEs were detected with total concentrations of around 1 μg/L in the river waters.     

Determination of organophosphate flame retardants and plasticizers in lipid-rich matrices using dispersive solid-phase extraction as a sample cleanup step and ultra-high performance liquid chromatography with atmospheric pressure chemical ionization mass spectrometry

A fast, robust and highly sensitive analysis method for determination of trace levels of organophosphate ester (OPE) flame retardants and plasticizers in lipid-rich samples was presently developed, and based on ultra-high performance liquid chromatography-tandem mass spectrometry coupled to a positive atmospheric pressure chemical ionization source (UHPLC-MS/MS-APCI(+)). The target OPEs in the sample were extracted from the biota samples, such as egg and liver, by ultrasonic extraction, and cleaned up further by dispersive solid phase extraction (d-ESP). As a result, background contamination was largely reduced. Different dispersive ESP sorbents were tested and primary secondary amine (PSA) bonded silica sorbents showed the best recoveries for these target OPEs. The recoveries obtained were in the range 54–113% (RSD < 17%), with method limits of quantification (MLOQs) ranging between 0.06 and 0.29 ng/g in egg, and 0.05 and 0.50 ng/g w.w. in liver sample. The matrix effects (MEs) associated with using APCI(+) and ESI(+) sources were investigated. APCI(+) showed much less ion suppression than ESI(+) for the determination of these OPEs. For egg and liver samples, the APCI(+) ME values ranged from 40% to 94%, while ESI(+) ME values ranged from 0% to 36%. Although APCI(+) was used for the determination of OPEs, the ionization mechanism might mainly be a thermospray ionization process. This UHPLC-MS/MS-APCI(+) method showed good response linearity for calibration (R2 > 0.99). The proposed method was applied to real environmental bird egg and fish samples, where several OPE were quantifiable and different OPE patterns was observed between samples.     

Application of dispersive liquid–liquid microextraction followed by HPLC–MS/MS for the trace determination of clotrimazole in environmental water samples

A method for the analysis of clotrimazole was developed with dispersive liquid–liquid microextraction for sample pre‐concentration and HPLC–MS/MS for analysis. A linear ion trap was used for the confirmation of clotrimazole identity in the samples. The developed method enables the analysis of clotrimazole in river water and sewage effluent from wastewater treatment plants with a LOQ of 0.7 ng/L. Environmental monitoring of clotrimazole was undertaken. Samples from river water and sewage effluents were analysed over a one‐year period. Clotrimazole was found in every tested sample with concentration range from 1 to 31 ng/L. The amount of clotrimazole in tested samples was highly dependent on sampling season. The highest results were obtained in summer and autumn.     

Suitability of solid-phase microextraction for the determination of organophosphate flame retardants and plasticizers in water samples

The feasibility of solid-phase microextraction (SPME) for the determination of several organophosphorus flame retardants and plastizicers in water samples by gas chromatography-nitrogen phosphorous detection (GC-NPD) is evaluated. These compounds have a wide range of polarities and volatilities and require a thorough optimisation of the different SPME parameters. Considering also possible contamination and carryover sources, the best compromise microextraction conditions were found to be direct extraction of 22 ml samples, containing 300 mg/ml of NaCl, with a PDMS-DVB coated fibre at room temperature. Although equilibrium was not achieved, an extraction time of 40 min allowed obtaining a good sensitivity (quantification limits between 0.010 and 0.025 ng/ml), comparable to that achieved by solid-phase extraction (SPE) of 1l samples, producing both similar values of precision and accuracy. Furthermore, the SPME method has shown to be free of matrix effects, avoiding the need of employing the standard addition procedure for quantification, and was suitable for the determination of eight of the nine considered compounds. Only tris-(2-ethylhexyl)-phosphate was neither determinable by SPME nor by SPE. Finally, the application of the developed methodology to the analysis of wastewater samples, showed that important concentrations of these compounds (up to 10 ng/ml) have been detected in treated sewage water, being discharged into the aquatic environment.     

A procedure for determination of cobalt in water samples after dispersive liquid–liquid microextraction

In this work, a procedure for preconcentration of cobalt using dispersive liquid–liquid microextraction (DLLME) with the reagent Br-TAO as complexing reagent was developed. The procedure is based on a ternary system of solvents, where appropriate amounts of the extraction solvent, disperser solvent and the chelating agent Br-TAO are directly injected into an aqueous solution containing Co(II). A cloudy mixture is formed and the ions are extracted in the fine droplets of the extraction solvent. After extraction, the phase separation is performed with a rapid centrifugation, and cobalt is determined in the enriched phase by FAAS. Under the optimized conditions, the detection limit obtained was 0.9 µg L^{− 1}. The enrichment factor and the consumptive index were 16 and 0.31 mL, respectively. The accuracy of the method was tested by the determination of cobalt in certified reference material of spinach leaves, NIST 1570a. The proposed procedure was successfully applied to the determination of cobalt in water samples.     

Coupling of homogeneous liquid–liquid extraction and dispersive liquid–liquid microextraction for the extraction and preconcentration of polycyclic aromatic hydrocarbons from aqueous samples followed by GC with flame ionization detection

In the present study, a simple and rapid method for the extraction and preconcentration of some polycyclic aromatic hydrocarbons in water samples has been developed. In this method, two sample preparation methods were combined to obtain high extraction recoveries and enrichment factors for sensitive analysis of the selected analytes. In the first stage of the method, a homogeneous solution containing an aqueous solution and cyclohexyl amine is broken by the addition of a salt. After centrifugation, the upper collected phase containing the extracted analytes is subjected to the following dispersive liquid–liquid microextraction method. Rapid injection of the mixture of cyclohexyl amine resulted from the first stage and 1,1,2‐trichloroethane (as an extraction solvent) into an acetic acid solution is led to form a cloudy solution. After centrifuging, the fine droplets of the extraction solvent are settled down in the bottom of the test tube, and an aliquot of it is analyzed by gas chromatography. Under the optimum extraction conditions, enrichment factors and limits of detection for the studied analytes were obtained in the ranges of 616–752 and 0.08–0.20 μg/L, respectively. The simplicity, high extraction efficiency, short sample preparation time, low cost, and safety demonstrated the efficiency of this method relative to other approaches.     

Combination of dispersive liquid-liquid microextraction with flame atomic absorption spectrometry using microsample introduction for determination of lead in water samples

The dispersive liquid-liquid microextraction (DLLME) was combined with the flame atomic absorption spectrometry (FAAS) for determination of lead in the water samples. Diethyldithiophosphoric acid (DDTP), carbon tetrachloride and methanol were used as chelating agent, extraction solvent and disperser solvent, respectively. A new FAAS sample introduction system was employed for the microvolume nebulization of the non-flammable chlorinated organic extracts. Injection of 20 μL volumes of the organic extract into an air-acetylene flame provided very sensitive spike-like and reproducible signals.Some effective parameters on the microextraction and the complex formation were selected and optimized. These parameters include extraction and disperser solvent type as well as their volume, extraction time, salt effect, pH and amount of the chelating agent. Under the optimized conditions, the enrichment factor of 450 was obtained from a sample volume of 25.0 mL. The enhancement factor, calculated as the ratio of the slopes of the calibration graphs with and without preconcentration, which was about 1000. The calibration graph was linear in the range of 1-70 μg L⁻¹ with a detection limit of 0.5 μg L⁻¹. The relative standard deviation (R.S.D.) for seven replicate measurements of 5.0 and 50 μg L⁻¹ of lead were 3.8 and 2.0%, respectively. The relative recoveries of lead in tap, well, river and seawater samples at the spiking level of 20 μg L⁻¹ ranged from 93.8 to 106.2%. The characteristics of the proposed method were compared with those of the liquid-liquid extraction (LLE), cloud point extraction (CPE), on-line and off-line solid-phase extraction (SPE) as well as co-precipitation, based on bibliographic data. Operation simplicity, rapidity, low cost, high enrichment factor, good repeatability, and low consumption of the extraction solvent at a microliter level are the main advantages of the proposed method.     

Application of dispersive liquid-liquid microextraction and high-performance liquid chromatography for the determination of three phthalate esters in water samples

A novel method, dispersive liquid-liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detector (HPLC-VWD), has been developed for the determination of three phthalate esters (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) in water samples. A mixture of extraction solvent (41 μL carbon tetrachloride) and dispersive solvent (0.75 mL acetonitrile) were rapidly injected into 5.0 mL aqueous sample for the formation of cloudy solution, the analytes in the sample were extracted into the fine droplets of CCl₄. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were determined by HPLC-VWD. Some important parameters, such as the kind and volume of extraction solvent and dispersive solvent, extraction time and salt effect were investigated and optimized. Under the optimum extraction condition, the method yields a linear calibration curve in the concentration range from 5 to 5000 ng mL⁻¹ for target analytes. The enrichment factors for DMP, DEP and DnBP were 45, 92 and 196, respectively, and the limits of detection were 1.8, 0.88 and 0.64 ng mL⁻¹, respectively. The relative standard deviations (R.S.D.) for the extraction of 10 ng mL⁻¹ of phthalate esters were in the range of 4.3-5.9% (n = 7). Lake water, tap water and bottled mineral water samples were successfully analyzed using the proposed method.     

Green methodology based on dispersive liquid–liquid microextraction and micellar electrokinetic chromatography for 5‐nitroimidazole analysis in water samples

Dispersive liquid–liquid microextraction has been proposed as an extraction technique combined with micellar electrokinetic chromatography (MEKC) for the analysis of eight 5‐nitroimidazole compounds, including some metabolites, in water samples. Determination has been carried out using a diode array detector, employing 20 mM sodium phosphate and 150 mM SDS as separation buffer. Separation has taken place under a voltage of 25 kV and a temperature of 20°C. Samples were prepared in a buffer without micelles and they were hydrodynamically injected at 50 mbar for 25 s, producing a sweeping effect on the analytes for increasing sensitivity. Different factors involved in the dispersive liquid–liquid microextraction procedure were optimized, such as sample pH, nature, and volume of extraction and dispersive solvents in the mixture, percentage of NaCl added to sample and shaking time after the injection of the extraction and dispersive solvents. The method was characterized for water samples, achieving detection limits lower than 2.4 μg/L. Trueness was checked in river, tap, and bottled water. Dispersive liquid–liquid microextraction combined with MEKC constitutes an easy, cheap, and green alternative for 5‐nitroimidazole analysis in environmental water samples.     

Evaluation of solid-phase microextraction with PDMS for air sampling of gaseous organophosphate flame-retardants and plasticizers

As an inexpensive, simple, and low-solvent consuming extraction technique, the suitability of solid-phase microextraction (SPME) with polydimethylsiloxane (PDMS) sorbent was investigated as a quantitative method for sampling gaseous organophosphate triesters in air. These compounds have become ubiquitous in indoor air, because of their widespread use as additive flame retardants/plasticizers in various indoor materials. Results obtained by sampling these compounds at controlled air concentrations using SPME and active sampling on glass fibre filters were compared to evaluate the method. A constant linear airflow of 10 cm s^–1 over the fibres was applied to increase the extraction rate. For extraction of triethyl phosphate with a 100-m PDMS fibre, equilibrium was achieved after 8 h. The limit of detection was determined to be less than 10 pg m^–3. The PDMS–air partition coefficients, K_fs, for the individual organophosphate triesters were determined to be in the range 5–60×10⁶ at room temperature (22–23°C). Air measurements were performed utilising the determined coefficients for quantification. In samples taken from a lecture room four different airborne organophosphate esters were identified, the most abundant of which was tris(chloropropyl) phosphate, at the comparatively high level of 1.1 g m^–3. The results from SPME and active sampling had comparable repeatability (RSD less than 17%), and the determined concentrations were also similar. The results suggest that the investigated compounds were almost entirely associated with the gaseous phase at the time and place sampled.     

A new device for magnetic stirring-assisted dispersive liquid-liquid microextraction of UV filters in environmental water samples

A new method based on dispersive liquid-liquid microextraction (DLLME) in combination with high-performance liquid chromatography (HPLC) has been developed for the analysis of UV filters. A specially designed flask, which has two narrow open necks with one of them having a capillary tip, was employed to facilitate the DLLME process. By adopting such a device, the extraction and subsequent phase separation were conveniently achieved. A binary solvent system of water sample and low-density extraction solvent (1-octanol) was used for the DLLME and no disperser solvent was involved. The extraction was accelerated by magnetic agitation of the two phases. After extraction, phase separation of the extraction solvent from the aqueous sample was easily achieved by leaving the extraction system statically for a while. No centrifugation step involving in classical DLLME was necessary. The analyte-enriched phase, floating above the sample solution, was elevated and concentrated into the narrow open tip of the flask by adding pure water into it via the other port, which was withdrawn with a microsyringe for the subsequent HPLC analysis. Under the optimized conditions, the limits of detection for the analytes were in range of 0.2-0.8 ng mL⁻¹ .The linearity ranges were 8-20,000 ng mL⁻¹ for HB, 7-20,000 ng mL⁻¹ for DB, 8-10,000 ng mL⁻¹ for BP and 5-20,000 ng mL⁻¹ for HMB, respectively. Enrichment factors ranging from 59 to 107 folders were obtained for the analytes. The relative standard deviations (n = 3) at a spiked level of 80 ng mL⁻¹ were between 1.4 and 4.8%. The proposed magnetic stirring-assisted DLLME method was successfully applied to the analysis of lake water samples.     

Quantitation of antioxidants in water samples using ionic liquid dispersive liquid-liquid microextraction followed by high-performance liquid chromatography-ultraviolet detection

A simple and efficient method, ionic liquid-based dispersive liquid-liquid microextraction combined with high-performance liquid chromatography-ultraviolet detection (HPLC-UV), has been applied for the extraction and determination of some antioxidants (Irganox 1010, Irganox 1076 and Irgafos 168) in water samples. The microextraction efficiency factors were investigated and optimized: 1-hexyl-3-methylimidazolium hexafluorophosphate [C(6)MIM][PF(6)] (0.06 g) as extracting solvent, methanol (0.5 mL) as disperser solvent without salt addition. Under the selected conditions, enrichment factors up to 48-fold, limits of detection (LODs) of 5.0-10.0 ng/mL and dynamic linear ranges of 25-1500 ng/mL were obtained. A reasonable repeatability (RSD≤11.8%, n=5) with satisfactory linearity (r(2)≥0.9954) of the results illustrated a good performance of the presented method. The accuracy of the method was tested by the relative recovery experiments on spiked samples, with results ranging from 85 to 118%. Finally, the method was successfully applied for determination of the analytes in several real water samples.     

Pressurised hot-water extraction of brominated flame retardants in sediment samples

Summary A pressurised, hot-water extraction (PHWE) method was developed for brominated flame-retardants in sediments. The effect of extraction time, temperature and pressure on PHWE recovery was investigated, together with solid-phase collection parameters (trapping material, length of trapping column, eluent composition). The concentrated extracts were analysed by GC-MS. PHWE recoveries were compared with those obtained by conventional Soxhlet-extraction. In general, recoveries were much higher with PHWE than with Soxhlet.     

Rapid pretreatment and determination of bisphenol A in water samples based on vortex‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with fluorescence detection

A method for the rapid pretreatment and determination of bisphenol A in water samples based on vortex‐assisted liquid–liquid microextraction followed by high‐performance liquid chromatography with fluorescence detection was proposed in this paper. A simple apparatus consisting of a test tube and a cut‐glass dropper was designed and applied to collect the floating extraction drop in liquid–liquid microextraction when low‐density organic solvent was used as the extraction solvent. Solidification and melting steps that were tedious but necessary once the low‐density organic solvent used as extraction solvent could be avoided by using this apparatus. Bisphenol A was selected as model pollutant and vortex‐assisted liquid–liquid microextraction was employed to investigate the usefulness of the apparatus. High‐performance liquid chromatography with fluorescence detection was selected as the analytical tool for the detection of bisphenol A. The linear dynamic range was from 0.10 to 100 μg/L for bisphenol A, with good squared regression coefficient (r² = 0.9990). The relative standard deviation (n = 7) was 4.7% and the limit of detection was 0.02 μg/L. The proposed method had been applied to the determination of bisphenol A in natural water samples and was shown to be economical, fast, and convenient.     

Dispersive liquid–liquid microextraction using extraction solvent lighter than water

For the first time a dispersive liquid–liquid microextraction method on the basis of an extraction solvent lighter than water was presented in this study. Three organophosphorus pesticides (OPPs) were selected as model compounds and the proposed method was carried out for their preconcentration from water samples. In this extraction method, a mixture of cyclohexane (extraction solvent) and acetone (disperser) is rapidly injected into the aqueous sample in a special vessel (see experimental section) by syringe. Thereby, a cloudy solution is formed. In this step, the OPPs are extracted into the fine droplets of cyclohexane dispersed into aqueous phase. After centrifuging the fine droplets of cyclohexane are collected on the upper of the extraction vessel. The upper phase (0.40 μL) is injected into the gas chromatograph (GC) for separation. Analytes were detected by a flame ionization detector (FID) (for high concentrations) or MS (for low concentrations). Some important parameters, such as the kind of extraction and dispersive solvents and volume of them, extraction time, temperature, and salt amount were investigated. Under the optimum conditions, the enrichment factors (EFs) ranged from 100 to 150 and extraction recoveries varied between 68 and 105%, both of which are relatively high over those of published methods. The linear ranges were wide (10–100 000 μg/L for GC‐FID and 0.01–1 μg/L for GC‐MS) and LODs were low (3–4 μg/L for GC‐FID and 0.003 μg/L for GC‐MS). The RSDs for 100.0 μg/L of each OPP in water were in the range of 5.3–7.8% (n = 5).