Broadened glass transition in a liquid-crystalline polymer studied by thermally stimulated currents,AC dielectric,dynamic mechanical,and DSC methods

Thermally stimulated currents (TSC), a. c. dielectric, dynamic mechanical (DMTA), and differential scanning calorimetry (DSC) methods were used to study the glass transition in a thermotropic liquid-crystalline copolyester. All the techniques were consistent in the determination of the main glass transition temperature. Using the high sensitivity of the TSC thermal sampling method, it was shown that cooperative glass transition-like relax-ations occur down to 100°C below the main glass transition. DSC was sensitive only to a broadening of the glass transition to about ca. 30°C, so it was concluded that the thermal sampling method is sensing a very small fraction of cooperatively relaxing species which cannot be detected by DSC. Ac dielectric measurements and DMTA also indicated that the glass transition was broad, but difficulties with overlapping transitions prevented quantitative determination of the breadth of the glass transition. The results suggest that the broad glass transition, in this mostly amorphous LCP, is due to chemical heterogeneity of the copolyester chain. Other evidence indicates that the broadening is not due to the oriented nature of the glassy state. Some discussion is presented concerning how the heterogeneous nature of the LCP glass leads to compensation of the Arrhenius curves obtained by the thermal sampling method. © 1993 John Wiley & Sons, Inc.     

不同软段结构聚氨酯-酰亚胺嵌段共聚物的合成及热性能研究

用二步法合成了不同软段 (PPO ,PEG ,PEPA)聚氨酯 酰亚胺 (PUI)嵌段共聚物 ,FTIR光谱表征了所有合成PUI分子主链均含有酰亚胺链段 ,并研究了PUI嵌段共聚物的热性能受软段类型及长度的影响 .DSC研究表明聚酯型PUI的软硬段之间的相容性比聚醚型PUI好 ,随相同软段分子量的增加 ,PUI体系的软硬段兼容性变差 ,并显示了相分离的特征 ;热失重 (TGA)研究得出不同软段的PUI样品的热稳定性大小顺序为 :PEPA PUI >PEG PUI>PPO PUI ;动态力学 (DMTA)研究给出了所合成的PUI样品在 5 0～ 2 0 0℃范围内均出现了较长的模量平台显示出有较好的耐热性 ,且随硬段含量的升高其储能模量不断增强     

UV curable epoxy acrylate-clay nanocomposites

UV curable epoxy acrylates were reinforced with two different organically modified montmorillonites (MMTs) and an unmodified MMT. Conversion and rate of polymerization was monitored by real time infrared spectroscopy (RTIR) and photo-DSC. Microstructures were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM) and optical clarity. Optical clarity of the films containing clay was quite good as only a slight decrease was observed. Physical properties of the reinforced films were examined by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), hardness and tensile testing. Enhancements in glass transition temperature (T_g), thermal stability and mechanical properties were observed. The films reinforced with the unmodified MMT exhibit the most significant enhancements in properties.     

Thermal properties of microcrystalline cellulose-filled PET–PTT blend polymer composites

Polymer composite materials were prepared from poly(ethylene terephthalate)–poly(trimethylene terephthalate) blends as the matrix and different microcrystalline cellulose (MCC) filler levels (0–40 wt%) using melt compounding followed by compression molding. The composites were analyzed using dynamic mechanical thermal analysis (DMTA), differential scanning calorimetry (DSC) and thermogravimetric analysis (TG). The DSC results indicated that there is no consistent or significant influence of the MCC addition on the glass transition (T _g), melting (T _m), and crystallization temperature of the composites. With increasing MCC content, dynamic mechanical properties improved because of the reinforcing effect of the MCC. The tan δ peak values from the DMTA were not significantly changed as the MCC content increased. TG indicated that the onset temperature of rapid thermal degradation decreased with increasing MCC content. It was also found that the thermal stability of the composites slightly decreased as the MCC content increased.     

Glass transition temperatures of polyurethane-urea elastomers based on N,N′-ethylenethiourea and N,N′-ethyleneurea as chain extenders

Glass transition temperatures of polyurethane-urea elastomers (PU) based on two urea derivatives, have been investigated with differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) methods. The DMTA measurements have been proved as more useful to determine an optimal annealing time and to controlling polyurethane-urea synthesis then the DSC analysis.

---

Zusammenfassung Mittels DSC und DMTA wurden die Glasumwandlungspunkte von Polyurethan-Harnstoff Elastomeren (PU) auf der Basis zweier Harnstoffderivate untersucht. DMTA-Messungen erwiesen sich als nutzbringender zur Bestimmung einer optimalen Temperungsdauer und zur überwachung der Polyurethan-Harnstoff-Synthese als die DSC-Analyse.

     

Thermal analysis of the structure of segmented polyurethane elastomers

Polyurethanes were prepared from 4,4′-methylenebis (phenyl isocyanate) (MDI), 1,4-butanediol (BD), and poly(tetrahydrofurane) polyether polyol (PTHF) by melt polymerization. The –OH functional group ratio of polyol/total diol was kept constant at 0.4, while the ratio of the isocyanate and hydroxyl groups (NCO/OH) changed between 0.940 and 1.150. The thermal analysis of the polymers by DSC and DMTA measurements indicated several transitions. The three glass transition temperatures observed were assigned to the relaxation of the aliphatic –CH₂– groups of the polyol, and to that of the soft and hard segments, respectively. The glass transition temperature of the soft and hard phase changed with the NCO/OH ratio indicating changes in phase structure and composition confirmed also by the maximum in the number of relaxing soft segments. Changes in the relatively small number of end-groups result in considerable modification of mechanical properties. Strength is determined by molecular mass and interactions, while stiffness depends mainly on phase structure. Surprisingly enough, –OH excess yields stiffer polymers, since the interaction of the –OH groups results in a decrease in the amount of the soft phase. A unique correlation was found between tensile modulus and the number of relaxing soft segments.     

Blends of isotactic polypropylene and natural terpene resins. I. Phase structure,thermal, and dynamic‐mechanical properties

This article discusses the influence of two natural terpene resins (NTR), poly(α‐pinene) (PαP A115) and poly(d‐limonene) (PL C115), on morphology, miscibility, thermal, and dynamic‐mechanical properties of their blends with isotactic polypropylene (iPP). The NTR have interesting physical and chemical properties, and they are approved for food contact application. From the results of differential scanning calorimetry and dynamic‐mechanical thermal analysis it was deduced that both the resins were completely miscible with the amorphous iPP up to the composition investigated here (70/30 wt %). Scanning electron microscopy (SEM) analysis instead showed that the 70/30 iPP/PαP A115 blend and 80/20 and 70/30 iPP/PL C115 blends contained very small domains homogeneously distributed into the matrix. It is hypothesized that the domains are likely formed by the terpene‐rich phase, and the matrix by the iPP‐rich phase (besides the crystallized iPP phase). The iPP‐rich phase and the NTR‐rich phase would have the glass transition temperatures so close that they cannot be resolved by DSC and DMTA. Finally, for the iPP/PαP A115 system an upper critical solution temperature (UCST) is proposed. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 867–878, 1999     

Thermal analysis of cellulose acetate modified with caprolactone

Cellulose acetate (CA) was modified with caprolactone (CL) under various reaction conditions in an internal mixer. The thermal behavior and relaxation transitions of the samples were determined by dynamic mechanical analysis and differential scanning calorimetry. Various relaxation transitions were detected in externally and internally modified cellulose acetate by DMTA. These were assigned to the glass transition of the main chain, to the movement of single glucose units and to hydroxymethyl groups. The β′ transition must belong to structural units larger than a single glucose ring and their formation must depend on sample preparation conditions. No transition could be assigned to grafted polycaprolactone (PCL) chains by DMTA. Contrary to other groups, we could not detect even the transitions of modified CA by DSC. Only the crystallization of oligomeric PCL homopolymer was observed mostly when it diffused to the surface of the sample.     

Measurement of glass transition temperature by mechanical (DMTA), thermal (DSC and MDSC), water diffusion and density methods: A comparison study

Glass transition measured by DMTA from the change in slope in storage modulus was 55 °C, which was 10.5 °C lower than the value measured by tan δ peak. Initial glass transition measured by DSC, increased exponentially and reached a constant value of 55 °C at or higher heating rate of 30 °C/min. Transition temperature, measured by MDSC, remained constant up to heating rate 15 °C/min and then decreased. The glass transition values determined from reversible heat flow was 60 °C. The break in diffusivity and density (i.e. volume) was observed at 50 °C below the glass transition temperature measured by thermal and mechanical methods.     

Thermo‐mechanical Properties of PEO‐PU/PAN Semi‐Interpenetrating Polymer Networks and their LiClO4 Salt‐Complexes

This paper is an investigation on the thermo‐mechanical properties of a new class of materials, which holds promise for its potential use as solid polymer electrolytes, i.e., SPE material. A series of poly(ethylene oxide)‐polyurethane/poly(acrylonitrile) (PEO‐PU/PAN) semi‐IPNs, along with their LiClO₄ salt complexes, were characterized for their thermal, mechanical and dimensional stability using DSC, TG‐DTA, UTM and DMTA. The glass transition temperature (T_g) of both the undoped and doped semi‐IPNs, obtained by DSC, remained well below room temperature (～?50°C to ?35°C), satisfying one of the essential requirements to serve as a SPE host matrix. The crystallization process in the PEO segments of the PEO‐PU/PAN semi‐IPNs was prevented at higher salt concentrations, which is attributed to the Li⁺ ion mediated pseudo‐crosslinks. Good thermal stability of the semi‐IPNs was evident from the degradation onset temperature (T₀～240°C) with a three‐stage degradation process, which is independent of the PAN content as observed from differential thermogravimetric studies. The incorporation of PAN in the PEO‐PU networks results in improved mechanical properties, such as tensile strength and modulus while retaining the flexibility of the semi‐IPNs. The peak temperatures and storage modulus obtained from DMTA correlates well with the observations of DSC and tensile measurements.     

Copolymers of PBT and nylon 4T

Polybutylene terephthalate–nylon 4T copolymers (PBT–PA 4T) are synthesized from the diamide of diaminobutane and dimethyl terephthalate (DMT) with butane diol and more DMT in a concentration range of up to 50% PA 4T. The polymerization conditions were similar to those for PBT: first, a melt polymerization, followed by solid-state post-condensation. The materials were studied by differential scanning analysis (DSC) (melting and crystallization behavior) and dynamic mechanical thermal analysis (DMTA) (glass transitions and torsion moduli). The water absorptions were determined at 100% RH. By increasing the PA 4T content in the copolymers, melting temperatures increased strongly, heats of fusion decreased slightly, and glass transition temperatures increased linearly. The torsion moduli above the glass transition temperature were higher. © 1993 John Wiley & Sons, Inc.     

Study on degrees of mesomorphic zone of polymerII. Determination of the degree of mesomorphic zone of eucommia ulmoides gum and natural rubber by dynamic mechanical thermal analysis and differential scanning calorimetry

In a foregoing article, a new method based on dynamic mechanical thermal analysis(DMTA)for determining the degrees of crystallinity of the natural rubber (NR) and the eucommia ulmoides (EU) gum, with different crosslink densities, has been established. In order to verify the effectiveness of this method, in the present paper, the degrees of crystallinity of NR and EU gum with different crosslink densities will be determined by differential scanning calorimetry (DSC). The results indicate that the degrees of crystallinity determined by DMTA are much higher than those of DSC. This is because the degree of crystallinity determined by DMTA involves not only the ratio of the crystalline zone, but also the ratio of the mesomorphic zone, while the degree of crystallinity tested by DSC includes only the ratio of the crystalline zone. So, the degree of crystallinity, the degree of mesomorphic zone and the degree of amorphous zone of NR and EU gums with different crosslink densities can be quantitatively determined by the combination of DMTA and DSC. The results show that the degree of crystallinity, the degree of mesomorphic zone and the degree of amorphous zone of NR (crystallized at −25 °C for 12 h) and EU gum are 33%, 53%, 14% and 34%, 54%, 13%, respectively. For NR, increasing the crosslink density or decreasing the induced time will decrease the degree of crystallinity and the degree of mesomorphic zone simultaneously, but will increase the degree of amorphous zones. For EU gum, increasing the crosslink density will decrease the degree of crystallinity and increase the degree of amorphous zone, but keep the degree of mesomorphic zone invariably consistent within the critical crystallization point, which is approximately 55%. At the end of the paper, the impact of crystallization on the mechanical properties of EU gum and NR is discussed as well.     

Thermal and mechanical characteristics of polyurethane/curaua fiber composites

Polyurethane composites reinforced with curaua fiber at 5, 10 and 20% mass/mass proportions were prepared by using the conventional melt-mixing method. The influence of curaua fibers on the thermal behavior and polymer cohesiveness in polyurethane matrix was evaluated by dynamic mechanical thermal analysis (DMTA) and by differential scanning calorimetry (DSC). This specific interaction between the fibers and the hard segment domain was influenced by the behavior of the storage modulus E′ and the loss modulus E″ curves. The polyurethane PU80 is much stiffer and resistant than the other composites at low temperatures up to 70°C. All samples were thermoplastic and presented a rubbery plateau over a wide temperature range above the glass transition temperature and a thermoplastic flow around 170°C.     

The mechanical properties of a model hydrogenated nitrile butadiene rubber (HNBR) following simulated sweet oil exposure at elevated temperature and pressure

A typical carbon black reinforced hydrogenated nitrile butadiene rubber (HNBR) was exposed to a mix of hydrocarbons (toluene, heptane and cyclohexane) at elevated temperatures and pressure in order to chemically age the material. The effect of this exposure on the mechanical properties is reported; the most significant change is a dramatic increase in tensile stiffness for specimens exposed at 160 °C for 12 weeks. Differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA) revealed changes in the glass transition behaviour of this material, with a general reduction in the magnitude of the glass transition with increasing ageing time. In addition, gravimetric studies of the swollen specimens after removal from the hydrocarbon mix showed that the more aged specimens underwent significantly slower drying rates compared to less aged specimens. These results may be explained by an increase in crosslink density in the materials being the main mechanism occurring during chemical ageing of these HNBR compounds.     

Thermal diffusivity of eutectic of alkali chloride and ice in the freezing-thawing process by temperature wave analysis

Thermal diffusivity of eutectic formed in aqueous alkali chloride solutions (NaCl, KCl, RbCl and CsCl) was determined by temperature wave analysis (TWA) during the freezing-thawing process of aqueous alkali chloride solution. An obvious change of thermal diffusivity in freezing-thawing processes of eutectic was observed with the super-cooling phenomena for each alkali chloride solute. The rate of thermal diffusivity decrease during the eutectic melting in comparison to the total decrease from the solid to the liquid state was observed larger than that of the heat of fusion measured by DSC, especially in the dilute concentration. It was confirmed that thermal diffusivity was sensitively influenced by the highly structure of the coexistence of eutectic crystallization and ice.     

Thermomechanical properties of cured isophtalic polyester resin modified with poly(ε-caprolactone)

The effect of a low profile additive, poly(ε-caprolactone) (PCL), on the thermal and mechanical properties of unsaturated polyester resins (UP) was investigated by differential scanning calorimetry (DSC), dynamic mechanical thermal analysis (DMTA), and tensile tests. The morphology of the systems has been studied by scanning electronic microscopy (SEM). Two PCL molecular mass were selected (PCL2: M _n = 2000 g mol⁻¹ and PCL50: M _n = 50000 g mol⁻¹) to analyze the influence of the molecular mass and the content of PCL on the UP resins and to establish the relation between thermomechanical behavior and morphology. DSC and DMTA glass transition temperatures (T _g) of the UP cured samples containing PCL indicate that PCL2 is miscible with UP whereas for UP + PCL50 system, T _g values are very close to the ones corresponding to neat UP. Besides in UP + PCL2 systems, one phase morphology is observed in which PCL2 would act as solvent of the reacting mixture along curing process; however, UP + PCL50 systems present phase-separated morphology. The presence of PCL2 and PCL50 in UP resin leads to a decrease of the tensile strength and the Young′s modulus as much notorious as the PCL concentration increases. For UP + PCL2 system the elongation at fracture increases in relation to neat UP, increasing as well with the PCL content.     

聚苯醚羧酸盐的聚集态结构

本文用热学、力学和散射方法研完了聚苯醚羧酸盐的链结构、羧化聚苯醚(C-PPO)在二氧六环溶液中用0.5 NaOH或CsOH的醇水溶液中和成钠型或铯型的C-PPO离聚体,用DSC测定一系列羧酸盐含量的C-PPO离聚体的玻璃化转变温度得到形成离子微区的临界阳离子浓度约为5mol％;动态力学谱中在高于玻璃化转变温度域出现的α松弛峰亦证明了微相结构的存在;SAXS结果表明其离子微区的尺寸约为30(?),其尺寸大小和离聚体中阳离子浓度无     

聚苯醚羧酸盐的链结构

本文用热学,力学和光散射方法研究了聚苯醚羧酸盐的链结构。羧化聚苯醚(CPPO)在二氧六环溶液中用0.5N NaOH(或 CsOH)的醇水溶液中和成钠型或铯型的 CPPO 离聚体,用 DSC测定一系列羧盐含量的 CPPO 离聚体的玻璃化转变温度得到形成离子微区的临界阳离子浓度约为5mol%,动态力学谱中在高于玻璃化转变温度域出现的α松弛峰亦证明了微相结构的存在。SAXS 结果表明其离子微区的尺寸约为3nm,其尺寸大小和离聚体中阳离子浓度无关。     

Poly(ethylene-co-vinyl alcohol) and poly(methyl methacrylate) blends: Phase behavior and morphology

In this work blends of poly(ethylene-co-vinyl alcohol) (EVOH) with different ethylene contents (27, 32, 38 and 44 mol%) and poly(methyl methacrylate) (PMMA) were prepared by mechanical mixing in the melted state. The miscibility and melting behavior as a function of blend composition and the ethylene content in EVOH copolymers were investigated by means of differential scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA). The morphology of the cryofractured surfaces was examined by scanning electron microscopy (SEM). DSC and DMTA data show that EVOH/PMMA blends are immiscible, independent of EVOH and blend composition. The SEM analysis in agreement with DMTA analysis indicates that the morphology of phases depends on the blend composition, with phase inversion occurring as the concentration of one or other polymer component increases. However, the copolymer composition apparently does not affect the domain size distribution for blends containing 20 wt% of EVOH or 20 wt% of PMMA. A better phase adhesion is observed mainly for blends with 50 wt% of each polymer component.     

Effect of halloysite nanotube on microstructure,rheological and mechanical properties of dynamically vulcanized PA6/NBR thermoplastic vulcanizates

Dynamically vulcanized thermoplastic vulcanizate (TPV) nanocomposites based on polyamide-6 (PA6) and acrylonitrile butadiene rubber (NBR) reinforced by halloysite nanotubes (HNT) were prepared via a direct melt mixing process. The effects of HNT on the physical, mechanical, and rheological properties of nanocomposites were investigated. The prepared PA6/NBR/HNT nanocomposites were characterized using X-ray diffraction (XRD), scanning electron microscopy (SEM), differential scanning colorimeter (DSC), dynamic mechanical thermal analysis (DMTA), and rheological measurements. The morphology study of prepared nanocomposites shows that the introduction of HNT into the PA6 phase causes a decrease in the size of NBR droplets. The mechanical measurements revealed that Young’s modulus of TPV nanocomposites increased with the HNT loading up to 54%. DMTA results show that the introduction of 10 wt% of HNT into the PA6/NBR TPV leads to a 30% increase in storage modulus. The rheological measurements revealed that the storage modulus of nanocomposites has an increase of more than 200% in the presence of 7 wt% of HNT loading. Analytical stiffness modeling of Young’s modulus of the TPV nanocomposites was investigated using Hui–Shia and Wu models. Both models have some deviations from experimental results and been modified to predict Young’s modulus of the nanocomposites containing HNT with more precisions. The viscosity behavior of TPV nanocomposites was studied using a Carruea–Yasuda model and showed that the yield stress of nanocomposites increases with higher HNT loadings, indicating the formation of a nanotube network along with NBR phase network.