Thermal degradation of epoxy-silica organic-inorganic hybrid materials

Degradation kinetics of organic-inorganic hybrid materials based on epoxy resin were investigated by thermogravimetric analysis (TGA). The hybrid materials were prepared from diglycidyl ether of bisphenol A (DGEBA) and 3-glycidyloxypropyltrimethoxysilane (GLYMO) polymerised simultaneously by poly(oxypropylene)diamine (Jeffamine D230). Nanometric level of homogeneity in the hybrids was verified by electron microscopy. Energy of activation of degradation for the hybrids with varying inorganic content, as well as for the unmodified epoxy-amine system, was determined by the isoconversional Kissinger-Akahira-Sunose method, and was found to be significantly higher for the hybrid materials than for the unmodified epoxy-amine system. The degradation process was described by empirical kinetic models. The results indicated that presence of the inorganic network influences the mechanism of degradation of organic phase. Greater thermal stability of hybrid materials was confirmed by other parameters obtained from TGA curves.     

DSC study of cure kinetics of DGEBA-based epoxy resin with poly(oxypropylene) diamine

Summary A kinetic study of cure kinetics of epoxy resin based on a diglycidyl ether of bisphenol A (DGEBA), with poly(oxypropylene) diamine (Jeffamine D230) as a curing agent, was performed by means of differential scanning calorimetry (DSC). Isothermal and dynamic DSC characterizations of stoichiometric and sub-stoichiometric mixtures were performed. The kinetics of cure was described successfully by empirical models in wide temperature range. System with sub-stoichiometric content of amine showed evidence of two separate reactions, second of which was presumed to be etherification reaction. Catalytic influence of hydroxyl groups formed by epoxy-amine addition was determined.     

Coating and Gas Permeation Properties of Urushiol-Based Organic/Inorganic Hybrid Films

The silica and urushiol based organic/inorganic hybrid was prepared with TEOS and urushiol by sol-gel process. GLYMO, as a silane-coupling agent, was used to obtain crack-free homogeneous films in various molar ratios, and to improve the adhesion between corona-treated BOPP substrate and the coatings. Two kinds of coating solutions were prepared; one was composed of TEOS and urushiol, the other was a mixture of TEOS, GLYMO and urushiol. Urushiol created less cracks on the film in a narrow range of molar ratios. As the amounts of urushiol were increased, the coating solutions quickly became heterogeneous. GLYMO was sufficient to prevent microcracks on the coated film and provided homogeneous coating solution. TEOS/urushiol and TEOS/GLYMO/urushiol coating solution gave insignificant effect on the permeability coefficients of oxygen, nitrogen and carbon dioxide, because the unsaturated alkyl side chain of urushiol might retard the formation of a dense structure between the inorganic silicate and the organic urushiol phase. From the antibacterial test of uncoating PP substrate and the coated film with hybrid solution, the reduction of bacteria of coating film was calculated to be 99.8%.     

Curing behavior and kinetics of epoxy resins cured with liquid crystalline curing agent

This article describes the synthesis of a liquid crystalline curing agent 4,4′-bis-(4-amine-butyloxy)-biphenyl (BABB), and its application as a curing agent for the epoxy resin (DGEBA) in comparison with normal curing agent, 4,4′-diaminobiphenyl (DABP). BABB was investigated with polarized optical microscopy, differential scanning calorimetry, and small-angle X-ray scatting, and the results showed that BABB displayed smectic liquid crystalline phase. The curing behaviors of DGEBA cured with BABB and DABP were studied by using differential scanning calorimetry (DSC), polarized optical microscopy (POM), and dynamic mechanical analysis (DMA). The results indicated that BABB showed a higher chemical reactivity than DABP. The kinetics was studied under isothermal conditions using an isoconversional method, and the isothermal DSC data can be fitted reasonably by an autocatalytic curing model. The nematic droplet texture was observed for the resulting polymer network of DGEBA/BABB system, while the DGEBA/DABP system showed an isotropic state. The storage modulus of DGEBA/BABB system was enhanced in comparison with DGEBA/DABP system because of the formation of LC phase, whereas the glass transition temperatures decreased because of the introduction of flexible spacer group.     

Reaction kinetics and network characterization of UV-curing polyester acrylate inorganic/organic hybrids

Polyester acrylate inorganic/organic hybrids were prepared using a sol-gel precursor, coupling agent, and reactive diluent. The hybrids were cured via a UV-free radical initiator. Design of experiments (DOE) was utilized to investigate reaction kinetics and complex variable interactions. The effects of the silicate groups on the free radical photo-curing reaction kinetics were investigated utilizing a time-resolved Fourier transform infrared (FT-IR) spectroscopy and a differential scanning calorimeter equipped with a photocalorimetric accessory (photo-DSC). Microgel and inorganic network formation during the UV-initiated free radical crosslinking reactions was suggested to describe the complex gel-point behavior. It was proposed that the formation of the inorganic silicate groups retarded the organic crosslinking reactions. The UV-cured inorganic/organic hybrid films exhibited more homogeneous film morphology compared to the organic counterparts. In the hybrid films, a core-shell like inorganic/organic particle morphology was observed. The UV-crosslinked organic phase forms the core, whereas, the inorganic silicate forms the surrounding shell.     

聚醚型氨酯酰亚胺/二氧化硅杂化材料的合成与性能研究

利用Sol Gel共聚合反应制备出聚醚型氨酯酰亚胺 (PUI) /二氧化硅 (SiO2 )杂化材料 .利用NMR、FTIR、TG、DSC及SEM等测试手段对性能进行了基本表征 .FTIR研究结果发现在 10 0℃下能同时完成有机相PUI的亚胺化和无机相SiO2 凝胶网络的Sol Gel转变 .TG及SEM发现SiO2 含量为 9wt%时SiO2 聚集相粒径在 0 2～1 0 μm之间 ,耐热性明显提高并达到最佳 ;发现SiO2 含量的增加其颗粒粒径不断增大 ,并不断聚集成大粒径SiO2 相 ,有机和无机相分离明显 .DSC研究显示 ,SiO2 相的引入 ,对杂化材料聚醚软段富集相的Tg 不产生明显影响 .     

Epoxy/poly(benzyl methacrylate) blends: miscibility, phase separation on curing and morphology

Diglycidyl ether of bisfenol-A (DGEBA)/polybenzyl methacrylate (PBzMA) blends cured with 4,4’-diaminodiphenylmethane (DDM) were studied. Miscibility, phase separation, cure kinetics and morphology were investigated through differential scanning calorimetry (DSC) and scanning electron microscopy (SEM). Non-reactive DGEBA/PBzMA blends are miscible over the whole composition range. The addition of PBzMA to the reactive (DGEBA+DDM) mixture slows down the curing rate, although the reaction mechanism remains autocatalytic. On curing, initially miscible (DGEBA+DDM)/PBzMA blends phase separate, arising two glass transition temperatures that correspond to a PBzMA-rich phase and to epoxy network. Cured epoxy/PBzMA blends present different morphologies as a function of the PBzMA content.     

Preparation and properties of polybenzoxazole-silica nanocomposites via sol-gel process

A novel organic/inorganic hybrid material has been prepared through the sol-gel process. A high temperature polymer, polybenzoxazole (PBO), was chosen as the organic phase due to its inherent low dielectric constant and low water absorption. The inorganic phase was generated via sol-gel reaction from a silica precursor, phenyltriethoxysilane (PTEOS). Due to the hydroxyl groups in the PBO precursor backbone and the water release during the cyclization of the precursor, the sol-gel reaction proceeded without the addition of water and any catalyst. After curing at 350 °C, we obtained the PBO/silica nanocomposites. From TEM and SEM photographs, the silica particles dispersed in the PBO matrix were nano-sized. With an addition of 100 wt% of PTEOS, the T_g of PBO was increased 35 °C. The dielectric constant of the hybrid materials increased with the increasing amount of PTEOS.     

PMMA/SiO_2透明块体材料的制备及其热性能

以正硅酸乙酯为前驱体,采用无溶剂水解技术,制备出了均一、稳定、透明的SiO_2溶胶,通过透射电子显微镜分析,粒径在100 nm左右;在溶胶中加入甲基丙烯酸甲酯(MMA)和偶氮二异丁腈(AIBN),采用热固化制备了透明的块体PMMA/SiO_2杂化材料,通过差热(DSC)和热重分析(TGA)研究了杂化材料的热性能. DSC结果表明,当体系中的SiO_2质量分数超过20%时,杂化材料无明显的玻璃化转变现象. TGA结果表明,杂化材料的分解温度提高约110 ℃. 透射电子显微镜观察结果表明,无机相均匀分散在有机相中,两相之间没有明显的相分离现象.     

Influence of fluorinated acids bonding on surface properties of crosslinked epoxy-based polymers

Two series of crosslinked fluorinated epoxy-based materials containing variable fluorine contents (from 0 to 6 wt.% F) were prepared using formulations based on a fluorinated acid (FA), epoxy monomer and a diamine. The epoxy monomer was based on diglycidyl ether of bisphenol A (DGEBA) while the curing agent was propyleneoxide diamine (Jeffamine D-230). The selected FA were: 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptanoic acid (FA1), perfluoro-heptanoic acid (FA2), and perfluoro-nonanoic acid (FA3). One of the series synthesized, FA-DGEBA/Jeffamine, is characterized by covalent attachment of the FA to the polymer by an ester bond. The other series, FA-Jeffamine/DGEBA, is characterized by ionic interaction between FA and polymer chains. The influence on thermal and surface properties of the architecture and chain-length of FA, and the nature of the linkage between FA and network precursors, was analyzed and discussed. It was found that both series showed high oleophobicity, but depending on the linkage between the fluorinated acid and the network, it was possible to develop hydrophobic or hydrophilic materials. The fluorine enrichment with the perfluoroalkyl substitutions was proved by XPS. By this technique it was possible also to analyze the concentration of ammonium groups at the surface.     

Cure Kinetics of DGEBA with Hyperbranched Poly （3-hydroxyphenyl） Phosphate as Curing Agent Studied by Non-isothermal DSC

IntroductionEpoxy resins are widely used in the fields of coa-tings,adhesives,insulating materials,etc..Diglycidylether of bisphenol A(DGEBA)is the most importantepoxy resin in industry because of its fluidity,physicaland mechanical properties after cure,…     

Epoxy/POSS organic-inorganic hybrids: ATR-FTIR and DSC studies

Organic-inorganic hybrid nanocomposites were prepared by reaction of an octaepoxy-silsesquioxane, OECh, with an epoxy-amine system. OECh was used to partially replace the thermosetting resin, diglycidyl ether of bisphenol A, DGEBA, in its reaction with an aromatic diamine, 4,4′-(1,3-phenylenediisopropylidene) bisaniline, BSA. The OECh was characterized by different techniques. The curing kinetics of ternary systems formed by DGEBA, OECh and BSA, was followed by Attenuated Total Reflectance-Fourier Transform Infrared Spectroscopy, ATR-FTIR. All the mixtures were prepared with a stoichiometric ratio between epoxy and amine groups. The degree of reaction of glycidyl epoxy ring along the curing cycle selected was obtained from the infrared spectra. A peak-height method based on the ratio of the height of the characteristic to reference absorbance peak was used. The curing kinetic of different blends was obtained by differential scanning calorimetry, DSC. Three different methods, the differential of Kissinger, the integral of Flynn-Wall-Ozawa and the phenomenological model of Kamal, were used in order to obtain the kinetic parameters of the cure reaction. It is observed that the presence of POSS accelerates the rate of opening of glycidyl epoxy rings from DGEBA. The behaviour of the mixture during the curing process can be explained with an autocatalytical model, corrected with the contribution of the diffusion of the molecules during the course of the reaction.     

Curing and thermomechanical properties of off-stoichiometric anhydride–epoxy thermosets

In the present work, we report the preparation and characterization of a new family of thermosets based on off-stoichiometric anhydride–epoxy formulations in the presence of an anionic initiator. Diglycidyl ether of bisphenol A (DGEBA) and hexahydro-4-methylphthalic anhydride (HHMPA) have been used as epoxy and anhydride comonomers, respectively, and 1-methylimidazole (1MI) has been used as anionic initiator. The isothermal curing kinetics and the thermal properties of the stoichiometric and the off-stoichiometric systems have been compared. The kinetics of the isothermal curing has been analyzed by differential scanning calorimetry (DSC) using an isoconversional method and the ?esták–Berggren equation to determine the activation energy, the frequency factor and the reaction orders. The materials obtained were characterized by DSC and dynamic mechanical analysis. Gelation during epoxy–anhydride condensation was determined by thermomechanical analysis. At the same curing temperature, the reaction is faster in the system with excess of epoxy groups. However, the glass transition temperatures of the partially cured stoichiometric system are greater. The gelation time of the off-stoichiometric system is shorter than that of the stoichiometric one. The results indicate that the dual-curing character of off-stoichiometric DGEBA/HHMPA thermosets with 1MI as anionic initiator makes them suitable for multistage curing processes with easy control of degree of cure and material properties in the intermediate stage and enhanced final material properties.

     

溶胶-凝胶法合成聚甲基丙烯酸甲酯/二氧化钛杂化聚合物材料

由共聚合在PMMA聚合物链段上引入了－Si(OR)₃功能团,通过溶胶－凝胶过程合成了PMMA/TiO₂杂化聚合物材料.溶剂抽提结果表明有化学键存在的杂化材料体系中凝胶的含量很高.通过FTIR测试对材料结构进行了分析,由TGA、DSC测试分析了杂化材料体系中无机组份的含量对材料性能的影响.     

UV curing of organic–inorganic hybrid coating materials

The effect of UV-curing time on the mechanism of interaction between the various precursor phases in a novel sol–gel-derived organic–inorganic hybrid coating material and the resulting mechanical and thermal properties of this material when coated onto substrates in thin film form have been examined using a variety of chemical and physical characterisation methods. Microstructurally, the hybrid coating materials examined were all a single amorphous phase and were all optically transparent. The degree of interaction between the organic and inorganic phases, the scratch behaviour of the coating materials and the thermal stability of the coating materials were all found to depend strongly on the UV curing time. For the particular proportions of inorganic and organic components used to make up this hybrid coating material, an optimum UV curing time of 10 min under a UV intensity of 46.3 mW cm⁻² was found to produce transparent coatings which adhered well to the substrates and which were robust in scratch tests on aluminium and polycarbonate substrates and abrasion tests on polycarbonate substrates.     

Improvement in fracture behaviors of epoxy resins toughened with sulfonated poly(ether sulfone)

The sulfonated poly(ether sulfone) (SPES) was successfully prepared using chlorosulfonic acid as a sulfonating agent. Diglycidylether of bisphenol-A (DGEBA) epoxy resins were modified with different contents of SPES, and the thermal and mechanical interfacial properties of DGEBA/SPES blends were investigated. As a result, the surface free energy of the blends was increased by the addition of SPES. DSC measurements revealed that the curing reaction was delayed with the increase of SPES content. Whereas, the thermal stabilities of the blends were slightly decreased as the SPES content increased. Meanwhile, the glass transition temperature and fracture toughness of the blends were increased with increasing SPES content, due to the improved intermolecular interactions, such as hydrogen bonding, between the hydroxyl group of DGEBA and the sulfonic group of SPES in the blends. The agreement could be observed by SEM which revealed phase separated morphology of DGEBA/SPES blends.     

Sol–gel derived hybrid coatings for the improvement of scratch resistance of polyethylene

Organic–inorganic hybrid materials were prepared through the sol–gel approach starting from tetraethoxysilane (TEOS), as silica precursor, and triethoxysilane terminated polymers; before gelling the solutions were applied to polyethylene (PE) films and slabs by spin-coating, without any previous surface pre-treatment of the substrate, and finally the coatings were thermally cured at 60 °C for 24 h. Among the various polymers used to prepare the coatings, only polyethylene-b-poly(ethylene glycol) copolymers gave good results in terms of adhesion to the PE substrates, and hybrid coatings with different organic–inorganic ratios were prepared. As suggested by visual inspection and SEM investigation, and confirmed by the critical loads derived from scratch tests, a good adhesion of the coating to the PE substrates was obtained, probably due to the presence of PE segments in the organic phase of the coating. Transparency as well as SEM and DSC data were in agreement with the formation of a nanostructured hybrid coating, with a high level of interpenetration between organic and inorganic domains. It was also observed that these hybrid coatings are able to improve significantly the scratch resistance and slightly increase the wettability with respect to uncoated PE. This approach to the surface-properties modification of PE appears as a simple and convenient method for the functionalization of PE substrates.     

Study on a novel thermoset nanocomposite form DGEBA–cycloaliphatic diamine and metal nanoparticles

The thermo-physical properties of diglycidyl ether of bisphenol A (DGEBA)/isophoronediamine (IPDA) with iron nanoparticles were investigated using DSC, DMT, and TG analysis. Because of the higher values of the glass transition, it is recognized that the optimum behavior of the three-component system corresponds to the 10% loading level of iron nanoparticles. The addition of iron nanoparticles into the epoxy matrix resulted in a significant increment in the storage modulus and crosslink density. Also, the DGEBA/IPDA/10% iron nanoparticles showed an enhanced thermal stability owing to the introduction of iron nanoparticles as reinforcing filler. Curing reaction of DGEBA/IPDA with 10% iron nanoparticles was investigated by DSC at dynamic mode. Activation energy was calculated based on Kissinger method (66.52 kJ mol^?1). Also, the advanced isoconversional method is utilized to describe the curing reaction process. In the dynamic DSC analyses, the curing kinetics could be successfully described with the two-parameter autocatalytic model (Sěsták–Berggren equation) and the overall reaction order was about 2.78.     

溶胶-凝胶法合成聚(甲基丙烯酸乙酯-甲基丙烯酸环氧丙酯)/SiO_2杂化聚合物材料

通过溶胶 凝胶过程合成了一系列存在相间偶联键的杂化聚合物材料 .IR分析证实了在无机组份与有机组份间存在碳氮键 ,其特征吸收峰在 1 2 5 0cm-1.DSC的测试结果则表明无机组份含量的增加提高了材料的Tg 值 ,从而提高了杂化材料的使用温度 .利用小角X ray散射 (SAXS)和电镜 (TEM)分析了不同无机组份、不同酸度下体系的形态结构 ,结果表明当无机组份与有机组份的摩尔比为 1∶1且体系的酸度适当时相容性最好 .     

Cationic copolymerization of diglycidyl ether of bisphenol A with phthalide or 3,3′‐diphtalide catalyzed by lanthanide triflates

Mixtures of the diglycidylether of bisphenol A (DGEBA) and phthalide (PT) or 3,3′‐diphthalide (DPT) were cured using ytterbium or lanthanum triflate as catalyst. The curing was studied by differential scanning calorimetry (DSC) and Fourier transform infrared in attenuated‐total‐reflection mode (FTIR/ATR). FTIR/ATR was used to monitor the competitive reactive processes and quantify the evolution of the epoxide and lactone groups. The T_g of the crosslinked materials increased when the proportion of lactone in the curing mixture decreased. The kinetics was studied with DSC experiments and isoconversional procedures. The differences in the reactivity of the systems were related to the Lewis acidity of the lanthanide salt used as initiator. The increase in the proportion of lactone leads to an increase in the reaction rate. The shrinkage was determined from the densities before and after curing and its evolution was studied by thermomechanical analysis. The materials obtained were characterized by thermogravimetry and dynamic mechanical thermal analysis. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1711–1721, 2006