Noise reduction in electronic speckle pattern interferometry fringes by merging orthogonally polarised speckle fields

The noise in sawtooth fringes generated by electronic speckle pattern interferometry (ESPI) is investigated. When deformations of depolarising objects are studied, the scattered object light can be decomposed into two orthogonal linearly polarised speckle patterns which are partially decorrelated. Their correlation coefficient decreases with increasing depolarisation coefficient of the object. By suitable merging of the phase distributions of these two speckle fields on the basis of a modulation depth analysis, the rms phase error in the ESPI sawtooth fringes can be reduced significantly.     

One-wavelength in-plane rotation analysis in electronic speckle pattern interferometry

The analysis of in-plane rigid-body rotations requires phase-shifting methods to determine the direction of rotation in conventional electronic speckle pattern interferometry (ESPI). The phase-shifting procedure makes the real-time measurements impossible. A quasi-real-time method is published recently, where the usual symmetric illumination is combined with a wavelength change before the second exposure. The present paper proposes a device sparing an alternative to this. The symmetric illumination is retained but the wavelength change is replaced by simple illumination direction changes.     

Wavelet filtering applied to time-average digital speckle pattern interferometry fringes

In this paper we are presenting a filtering scheme using Symlet wavelet to remove the speckle noise from the time-averaged digital speckle pattern interferometry fringes. To demonstrate the potential of Symlet wavelet filtering, experiments are conducted to remove the speckle noise from the fringes recorded for the surface of computer hard disk. Experimental results demonstrate that this filtering removes the speckle noise to the large extent.     

Evaluation of the 1D empirical mode decomposition method to smooth digital speckle pattern interferometry fringes

The 1D empirical mode decomposition method is applied to reduce speckle noise in the correlation fringes produced in digital speckle pattern interferometry. This method is based on the decomposition of a signal in a sum of well-behaved fast and slow oscillation modes through a sifting process, which generates a fully data-driven technique. Consequently, this is an adaptive approach and the use of basis functions in the analysis process is not required. The denoised signal is given by the residue obtained after the fast oscillation modes are removed. The performance and limitations of the denoising technique are analyzed using computer simulated fringes and these results are compared with those obtained using a wavelet sub-band removal approach. An application of the EMD method to denoise experimental correlation fringes is also presented.     

Sound field monitoring by tomographic electronic speckle pattern interferometry

Time-averaging electronic speckle pattern interferometry (ESPI) allows to record the phase modulation of light that has propagated through a sound field. When such data are collected from different projection directions the three-dimensional spatial distribution of amplitude and phase of the sound are obtained by tomographic back projection. The performance of such a setup increases with the number of projection directions, the number of effective resolution elements in the detector, and the number of recordings taken in averaging. These efforts, however, compete with the need for acceptable recording and processing times. Recent improvements in time-averaging ESPI enable even demanding applications in sound field monitoring. This is demonstrated in the design of a 38.5 kHz ultrasound source composed of a large number of individual piezoelectric transducer elements and intended to generate highly directive audio sound by nonlinear mixing in air (parametric array). The success of this method relies essentially on a non-intrusive control of the spatial homogeneity of the ultrasound field. Tomographic ESPI data have guided in a delicate alignment of the transducer elements yielding the expected narrowing of the angular radiation of the audio sound.     

用电子散斑干涉法测量材料热膨胀系数

 利用双光束电子散斑干涉法（ESPI）对试件受热变形进行了实时观测，针对一次实验过程中得到的图片较多（300～500幅）的特点，在图像处理时摒弃了以往的手动识别等位移线的办法，用MATLAB语言编写了批处理程序，能够在采集的大量散斑图片中自动快速准确地标定等位移线，得到相应的位移和应变，并结合实时测量的温度值，获得了45钢和LY12铝合金在不同温升率下的热膨胀系数及其随温度的变化。实验结果表明，在涉及的温升率范围内，温升率的改变对材料热膨胀系数的影响不明显，材料的热膨胀系数随温度的升高略有上升。     

The design of a non-cube beam-splitter used for electronic speckle pattern interferometry

A non-cube beam-splitter (NCBS) is proposed, by which an incident beam can be separated largely in a direction and then the lights from the test object and the lights from a reference surface placed adjacently to the test object can be combined to construct a simple electronic speckle pattern interferometry (ESPI) system. Two mainly useful quantitative ways, to calculate the phase change of the test object, the phase-shift and the fringe carrier method with Fourier transform, can be achieved in the ESPI system with the NCBS. Experiments with phase-shifting and fringe carrier method are completed. The experimental results show that the monolithic design of the proposed NCBS is effective in ESPI measurement and immunity to vibrations.     

一种可实现电子散斑干涉的新型大错位方棱镜

设计了一种可实现电子散斑干涉的大错位方棱镜.将普通方棱镜的一个面磨去一个楔角后变为斜面,该斜面和相邻的一个面镀反射膜,其他二个面镀增透膜.垂直入射的光线经过分光后变成二束光,分别经过平面反射和斜面反射,出射的二束光线就分开了.将该大错位方棱镜置于CCD镜头前,一个物体可以成二个错位的像;相邻的二个物体可叠加成像.错位量由楔角决定,错位量足够大,可实现大错位电子散斑干涉.根据试件大小和成像距离,楔角的大小可选择在1°到10°之间.对中心加载周边固定圆盘进行了电子散斑载频干涉实验,证明了大错位方棱镜能够高质量地实现电子散斑干涉,实现位移场测量.     

Homomorphic partial differential equation filtering method for electronic speckle pattern interferometry fringes based on fringe density

Noise reduction is one of the most exciting problems in electronic speckle pattern interferometry. We present a homomorphic partial differential equation filtering method for interferometry fringe patterns. The diffusion speed of the equation is determined based on the fringe density. We test the new method on the computer-simulated fringe pattern and experimentally obtain the fringe pattern, and evaluate its filtering performance. The qualitative and quantitative analysis shows that this technique can filter off the additive and multiplicative noise of the fringe patterns effectively, and avoid blurring high-density fringe. It is more capable of improving the quality of fringe patterns than the classical filtering methods.     

用数字滤波消除散斑条纹图噪声

本文讨论了散斑摄影条纹图的噪声来源及模型,设计合适的数字滤波器.采取正交实验手段,全面分析了噪声、条纹对比度和密度对条纹方向及间距测量精度的影响.     

Measurement of modal damping by electronic speckle shearing interferometry

A time-average electronic speckle shearing interferometer (ESSI) has been used for modal damping measurement. This is effected by a new fringe enhancement technique. The damping factor of a cantilever measured by using this technique agrees well with the value measured by using the accelerometer method. The study shows that time-average speckle interferometry can be used as a convenient tool for modal damping measurement.     

散斑干涉相位条纹图的频域滤波处理

为了解决在数字散斑干涉技术测量时,散斑干涉相位条纹图像中大量噪声对相位解包裹结果和精度产生严重影响的问题,介绍了一种条纹正余弦分解和频域低通滤波结合的方法,实现了散斑干涉相位条纹图的高精度滤波。该方法的基本思路是在对相位图像进行滤波处理前,先将相位图通过正余弦函数进行映射转换成两幅图,分别经过频域滤波,然后再合成为相位图。这种分解频域滤波方法可以在滤波的同时,有效保留相位跳变信息。实验结果表明：与传统的图像降噪方法相比,该方法能够在保留图像“尖峰”信息的基础上,较好地滤除图像中的散斑噪声,方法简单有效,有效解决了传统滤波方法应用在相位条纹图中,相图灰度信息丢失10%~40%的问题。     

Comparison between instantaneous and integral intensities in dynamic speckle pattern interferometry

A new speckle measurement technique called temporal speckle pattern interferometry or time sequential speckle pattern interferometry has been developed recently. Its principle is that by capturing the temporal speckle patterns related to the object deformation or displacement, the whole-field displacement, the amplitude of the vibrating object and the shape of the tested object can be calculated through speckle intensity fluctuation scanning technique or Fourier-transforming method. In this paper, we combine the analytical and numerical methods to simulate the properties of the time demodulation in temporal speckle patterns interferometry techniques. The performance of three kinds of temporal phase sequences, power, exponential and harmonic phase sequences, are studied with the parameters of temporal speckle intensity fluctuation, the value of the spatial phase term, optical integral time of the recording camera and the initial phase of the temporal speckle intensities. The results indicate that the normalized value and period change of the instantaneous intensity are nearly coincident with that of the integral intensity for the harmonic temporal phase sequences and are different for the power and exponential temporal phase sequences.     

Measurement of the off-plane displacement of carbon steel corrosion with twin-object-beam electronic speckle interferometry

In this paper, twin-object-beam electronic speckle interferometry is used to study the longitudinal corrosion of carbon steel. The displacement expression of this technique is deduced and optical fibers are used to reduce the influence of the optical system and improve the quality of speckle pattern. Twin-object-beam electronic speckle interferometry cannot only quantitatively cipher out off-plane displacement as a result of corrosion, but also estimate the change of corrosion speed.     

Improved evaluation of electronic speckle pattern interferograms by photogrammetric image analysis

Electronic speckle pattern interferometry (ESPI) is a well-established tool for non-destructive testing. It allows the quantitative determination of surface deformations and micro-movements with a sub-micrometer resolution. In the case of objects which are extended in depth, however, the evaluation and interpretation of the resulting correlation fringe patterns can be affected by perspective image distortions as well as by a varying image size. In this paper a method for combination of ESPI with a photogrammetric 3D coordinate measurement is presented. In this way, interferogram data are precisely allocated in 3D-space. Furthermore, it is possible to take into account a spatially varying sensitivity vector. The utilizability of the method is demonstrated by a deformation measurement on a stone sculpture.     

电子散斑干涉载频调制形貌测量方法的分析

根据电子散斑干涉载频调制测量物体形貌的基本原理,物体表面的微小偏转可引入包含物体高度信息的载波干涉条纹。将物体的偏转视为变形,对物体变形与载波干涉条纹之间的关系进行了讨论,得出了离面位移引入载波和面内位移引入含有物体高度信息相位的结论。发现利用典型电子散斑干涉系统测量物体形貌效果最好,并通过实验得到了验证。     

Variational denoising method for electronic speckle pattern interferometry

Traditional speckle fringe patterns by electronic speckle pattern interferometry (ESPI) are inherently noisy and of limited visibility, so denoising is the key problem in ESPI. We present the variational denoising method for ESPI. This method transforms the image denosing to minimizing an appropriate penalized energy function and solving a partial differential equation. We test the proposed method on computer-simulated and experimental speckle correlation fringes, respectively. The results show that this technique is capable of significantly improving the quality of fringe patterns. It works well as a pre-processing for the fringe patterns by ESPI.     

Measuring thickness change of transparent plate by electronic speckle pattern interferometry and digital image correlation

The thickness change of transparent plates was measured by electronic speckle pattern interferometry (ESPI) method and digital image correlation (DIC) method. An out-of-plane ESPI system was developed based on the Michelson interferometer, and a new thickness measurement method was designed, which is on the basis of Snell's law of refraction and DIC. The main principles and experimental procedures of these two methods were presented. The thickness change of polymethyl specimens under uniaxial tensile loading were measured by the optical techniques and compared with each other. The results reveal that the data obtained with DIC method achieve better linearity than ESPI.