Wavelength stabilization of a 980-nm semiconductor laser module stabilized with high-power uncooled dual FBG

An optimized dual fiber Bragg grating (FBG) is proposed for 980-nm semiconductor lasers without thermoelectric coolers to restrict temperature-induced wavelength shift.The mathematical model of the temperature-induced wavelength shift of the laser with the dual FBG is built using the external cavity feedback rate equations.The external cavity parameters are optimized for achieving the stability mode-locking laser output.The spectral characteristics of the dual FBG stabilized laser are measured to range from 0 to 70 °C.The side mode suppression ratio (SMSR) is more than 45 dB,while the full-width at half-maximum (FWHM) is less than 1 nm.The peak wavelength shift is less than 0.1 nm.The dual FBG wavelength shift proportional coefficient is between 0.1086 and 0.4342.     

Low-threshold performance of fiber Bragg grating external-cavity semiconductor lasers using genetic algorithms

The lowest threshold current of the external-cavity semiconductor laser with fiber Bragg grating using genetic algorithms is investigated. Effects of the external cavity length, coupling efficiency and anti-reflection coating reflectivity on static characteristics, such as L-I curves and side mode suppression ratios (SMSR) are investigated by using multi-mode rate equation. It is found that the reflectivity of the anti-reflection coating for low-threshold performance needs to be increased at the cost of the stability of the fiber grating external-cavity semiconductor laser. The optimal external cavity length obtained by genetic algorithms can be used to obtain the lowest threshold current for sacrificing a little SMSR. However, with the decrease of AR-coating reflectivity, output powers and SMSRs are slightly dependent on the external cavity length.     

波长可调谐超短光脉冲的简便高质的生成技术

提出了一种以处于增益开关调制状态下的法布里珀罗(Fabry-Pérot)半导体激光器作为光源,采用简单的自激注入锁定方式,以生成波长可调谐的超短光脉冲的实验系统。该实验装置中,激光器的外腔包括两个串联在一起的布拉格光纤光栅,一个掺铒光纤放大器(EDFA),一个光耦合器和两个环行器,其作用是选模,以及增强并控制反馈回激光器内腔的光强。该实验系统简单而高效,在24nm的波长调谐范围内获得了边模抑制比高于40dB的单模光脉冲输出;而在1521.8nm和1550.0nm之间28.2nm的波长调谐范围内,边模抑制比高于35dB。所得到的各个单波长激光脉冲的时域半峰全宽为140~260ps,各个脉冲的光谱半峰全宽皆为0.1nm。     

Influences of geometry parameter on mode suppression ratio of fiber grating external cavity semiconductor laser

According to equivalent external cavity approximation model, after taking into account the joint contribution of semiconductor laser, external cavity and fiber grating (FG) to the phase condition, the mode distribution of the fiber grating external cavity semiconductor laser (FGESL) can be determined. As a result, the effect of the FG external cavity length (L) on the side mode suppression ratio (SMSR) of the FGESL is investigated theoretically. The results show that with the injected current and the coupling efficiency increase of the SMSR has taken on rise at all. For strong feedback (R₂ = 10^?4), the SMSR become more flattened with more than 40 dB, but, for weak feedback condition, The SMSR have lesser than 35 dB by an oscillation during rising course. Under the condition of short external cavity, the SMSR is in deep relation to the external cavity length, but the SMSR of longer external cavity is smaller than the SMSR of shorter external cavity on the whole and for 8–11 mm of the external cavity length, the SMSR of the FGESL has better (SMSR > 40.8 dB), and the SMSR become more flattened.     

双光纤光栅外腔半导体激光器相干失效研究

根据双光纤Bragg光栅(FBG)外腔半导体激光器相干失效的物理过程, 运用速率方程和双FBG耦合模理论, 分析了双FBG外腔半导体激光器相干失效产生和控制的条件, 提出了实现和控制双FBG外腔半导体激光器相干失效多模稳定工作的方法. 双FBG外腔半导体激光器在相干失效下具有多模的稳定工作状态, 相干失效长度缩短, 相干失效长度内光谱稳定. 实验测量结果表明, 外腔反射率为3%时, 从非相干失效状态到相干失效状态, 半峰值全宽度从0.5 nm突然展宽到0.9 nm. 在相干失效状态下, 功率稳定, 边模抑制比大于45 dB, 在0℃–70℃工作温度范围内峰值波长漂移小于0.5 nm, 最小相干失效长度小于0.5 m. 双FBG外腔半导体激光器相干失效的应用对提高光纤放大器和光纤激光器的性能具有重要意义. 关键词： 非线性 半导体激光器 双光纤Bragg光栅 相干失效     

A theoretical model used to analyze the output characteristics of fiber grating external cavity semiconductor lasers

Using the ray trace method, the expression of the output spectrum of the fiber grating external cavity semiconductor laser (FGESL) has been deduced and the fine structure of the output spectrum has been investigated. Due to the fiber grating (FG) external cavity, within the reflection bandwidth of the FG, the energy distribution varies seriously, there exist many peaks and the number of peaks is related to the length of the external cavity. With increase in the bias current, the output power and side-mode suppression ratio (SMSR) of FGSEL tend to increase accompanied by fluctuation, and the fluctuation will weaken with the decrease in the reflectivity of the front facet of the semiconductor laser.     

电流调谐光纤光栅外腔分布布拉格反射激光器

报道一种新颖的波长可调谐光纤光栅外腔分布拉格反射激光器。把经过金属管封装的光纤面布拉格光栅作为激光二极管的外腔反射镜,得到的单模激光输出不仅线宽窄,边模抑制比高,而且,调节流过金属管的电流,可在5nm范围内的6个不同波长间转换。     

稳定可调谐的单纵模多环形腔掺铒光纤激光器

提出了一种多环形腔(MRC)结构的稳定可调的单纵模(SLM)掺铒光纤激光器,多环形腔结构由双环形有源腔和两个次级无源腔组成.这种激光器是利用光纤法布里珀罗可调滤波器(FFP-TF)以及光学光栅滤波器(OGF)两种滤波器和多环形腔结构相结合来共同选模.可实现波长调节范围为1528～1565 nm,在整个波长调节范围内边模抑制比大于44.53 dB,在1554 nm附近边模抑制比可以达到最大值51.18 dB, 输出功率为-8.84 dBm,通过应用多环型腔结构,激光器的输出很稳定,在18 min的观察时间内,中心波长的变化小于0.02 nm,输出功率的变化小于0.04 dBm,实现了稳定且可调谐的单纵模输出.     

超低频率全正色散半导体可饱和吸收镜被动锁模光纤激光器

 通过延长激光器环形腔腔长,利用高浓度掺杂的单模掺镱光纤,搭建了超低重复频率、全正色散结构的半导体可饱和吸收镜被动锁模光纤激光器。激光器的中心波长、重复频率、平均功率及单脉冲能量分别为1 064 nm,281.5 kHz,11 mW和39 nJ。为了稳定中心波长,实现自启动,激光器腔体内接入了一个带通滤波器。该激光器运行稳定,无调Q不稳定现象,极大减小了半导体可饱和吸收镜被损坏的机会。     

光纤光栅外腔半导体激光器的多参量优化分析

采用多参量优化的多目标遗传算法优化了光纤光栅外腔半导体激光器（FGECL）管芯的两个端面反射率和外腔长度.研究了FGECL的阈值特性,并对多个参量优化和单个参量优化的结果进行了比较分析.表明获取最低阈值电流,要以激光器的电光转换效率和输出光功率为代价,从而得到高边模抑制比、窄光谱线宽、良好动态特性和高调制速率的FGECL.并且发现当两端面的反射率增加,同时激射波长在外腔长度中形成稳定谐振时,激光器的阈值电流达到最小值,但相应的电光转换效率和出光功率会急剧地减小.     

级联光栅结合Sagnac环的可调谐光纤激光器

提出并验证了一种单-双波长可调谐掺铒光纤激光器。利用级联光纤布拉格光栅(Cascaded Fiber Bragg gratings,Cascaded FBGs)结合Sagnac环结构所产生的复合滤波效应,实现较高精细度滤波,并通过调节环内偏振控制器(Polarization Controller,PC),引入双折射效应,得到波长可调谐的光纤激光器。基于耦合模理论并使用传输矩阵法对该结构的传输特性进行了分析,在此基础上搭建实验系统,验证了理论分析的正确性。实验结果表明:通过调节PC,激光器输出激光的波长范围约为1 555.644～1 556.112 nm,双波长间隔的可调范围约为0.108～0.452 nm,单-双波长的边模抑制比(SMSR)均高于40 dB;在稳定性测试中,输出单-双波长激光的波长最大漂移量小于0.008 nm。该方法具有结构简单、调谐方便、易于实现且精细度较高的优点,可应用于密集波分复用及全光通信系统等领域。     

Dual-cavity dual-output multi-wavelength fiber laser based on nonlinear polarization rotation effect

We demonstrate a multi-wavelength fiber laser based on nonlinear polarization rotation (NPR) in dual-cavity configuration with two output ports. The laser employs a piece of erbium doped fiber (EDF) and semiconductor optical amplifier (SOA) as the gain medium in a separate cavity. By incorporating PCF in the dual cavity the non-linear polarization rotation (NPR) effect is enhanced and thus higher output and more oscillating lasing can be achieved. The laser produces three strong lines with a spacing of 2.40 nm and side mode suppression ratio (SMSR) of more than 10 dB at 1535 nm region. Another output produces 8 lines of optical comb with a spacing of 0.54 at 1570 nm region.     

A narrow-line Erbium-doped fiber laser and its application for testing fiber Bragg gratings

We inspect the spectral features of a diode-pumped Erbium-doped fiber laser (EDFL) with a Fabry-Perot cavity composed of a wavelength-selective coupler in the form of fiber Bragg grating (FBG) and wavelength-insensitive Faraday rotator mirror (FRM). High accuracy for the spectral measurements is provided with the use of an optical heterodyne scheme where the EDFL output is mixed with radiation from a narrow-line semiconductor laser, allowing the detection of the EDFL spectra with a sub-pm resolution. The heterodyne scheme permits precise measurements of the EDFL line-width as a function of the cavity length and pump power. It is worth noticing a narrow-line (a few pm) operation of the EDFL with a short length (<3 m) cavity and low (<5) excess of pump power over the laser threshold. The spectral response of the EDFL to a slow sinusoidal modulation of a physical length of the FBG coupler is analyzed and it is shown that as high as ∼1-nm modulation of the EDFL optical spectrum is attainable at maximal modulation amplitudes. The narrow-line EDFL with a modulated generation wavelength is hereby demonstrated to be a tool for high-resolution measurements of reflection spectra of FBGs, which is to the best of our knowledge a novel application of the EDFL.     

An energy-efficient tie-type architecture for stable and wavelength-tunable SOA-based fiber laser

A new and energy-efficient tie-type architecture for stable and wavelength-tunable semiconductor optical amplifier (SOA)-based fiber ring laser is proposed and experimentally investigated. Here, the tie-type laser configuration is constructed by two Sagnac fiber loops. The proposed laser also can extend the lasing wavelength to longer wavelength (L-band) even only the C-band SOA is used. The proposed tie-type architecture has >5 dB higher output optical power at bias current of 80 mA when compared with the single ring SOA-based fiber laser. In this measurement, the output power, wavelength tuning range, side-mode suppression ratio (SMSR) and output stability of proposed fiber laser have also been analyzed and discussed.     

滤波对8字腔掺铒光纤激光器锁模运转的影响

构建了基于损耗非对称非线性光学环镜的8字腔掺铒光纤锁模激光器,并讨论了腔内滤波带宽对腔内脉冲演化和激光器输出特性的影响.在非线性光学环镜中引入双向输出耦合器,耦合器和传输光纤位置的不对称产生非互易性,实现锁模运转.利用自制的可调谐滤波器实验研究了滤波带宽对激光器的影响.当滤波带宽为2.1 nm时,腔内脉冲的演化过程受滤波和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲半高全宽分别为583.7fs和2.94 ps.随着滤波带宽增大,滤波的作用逐渐减弱,激光器两路输出脉冲参数逐渐接近,并接近傅里叶变换极限脉冲.当滤波带宽较大时,腔内脉冲的演化过程受增益谱和孤子效应的共同作用,激光器顺时针和逆时针输出脉冲均为变换极限脉冲,半高全宽约为440 fs.通过调节滤波器中心波长实现了对激光器输出脉冲光谱的连续调谐,调节范围大于30 nm.     

A dual-pass Mach–Zehnder interferometer filter using a TCF loop mirror for double-wavelength fiber lasers

A dual-pass Mach–Zehnder interferometer filter using a section of twin-core fiber (TCF) loop mirror is proposed. The filter is theoretically and experimentally studied for various interferometer arm difference when TCF length is constant. Theoretical results are validated by the experimental demonstration and in good agreement with the experimental results. And then, by using the filter in a ring fiber laser, a stable and switchable dual-wavelength lasing is obtained experimentally. The 3-dB bandwidth and the SMSR of the output laser are 0.015 nm and higher than 62.4 dB, respectively. The peak power fluctuation and wavelength shift are also monitored to be less than 0.04 dB and 0.02 nm over an hour at room temperature. Furthermore, the output laser can be switched between single and dual wavelength by carefully adjusting the PCs. The experimental results show that the filter can suppress mode competition effectively, improve the SMSR availably, and enhance the stability of the output lasing.     

光纤光栅外腔半导体激光器纵模特性研究

用速率方程对光纤光栅外腔半导体激光器（ＦＢＧ－ＥＣＬ）的静态工作特性进行模拟计算,获得了这些特性同器件结构参数和工作条件的关系。用自行研制的光纤光栅与增透半导体激光器管芯耦合,获得了边模抑制比大于４０ｂＢ、线宽约为０．１ｎｍ的单纵模工作的实验结果,与计算结果基本吻合。     

All-fiber actively Q-switched fiber laser tuned by a pair of temperature controlled fiber Bragg gratings

We report an all-fiber actively Q-switched erbium-doped fiber laser, where the linear laser cavity mirrors are composed of two fiber Bragg gratings (FBGs). The laser oscillation wavelength could be tuned by this pair of temperature controlled FBGs. The Q-switching is achieved by an all-fiber phase modulation device. Using this system, we could obtain stable Q-switched laser pulses output, which could be optimized by tuning the reflection wavelengths of the two FBGs to be adjacent to each other. Instead of being modulated by the FBG filter in high-speed oscillation, this fiber laser system is operating in the Q-switched regime using an all-fiber phase modulator, producing a more stable laser output spectrum.     

Monochromatization of semiconductor laser diodes using one-dimensional photonic crystals

The results on the development of the single-frequency semiconductor laser with external cavity based on a fiber Bragg grating (one-dimensional photonic crystal) formed in a single-mode fiber waveguide are presented. Stable single-frequency lasing at a wavelength of 977 nm with a spectral half width of 0.2 nm is achieved with a laser power output of 350 mW. The temperature dependence of lasing parameters is studied.     

Quasi-distributed fiber Bragg grating sensor system based on a Fourier domain mode locking fiber laser

A novel quasi-distributed fiber Bragg grating (FBG) sensor system based on Fourier domain mode locking (FDML) fiber laser is proposed and demonstrated. The low reflectivity FBGs with the same Bragg wavelength are connected cascaded in a long fiber working as the sensing elements of the sensor system as well as the wavelength and cavity length selecting elements of the FDML laser. By adjusting the driving frequency of the FDML fiber laser, lasing with different selected cavity lengths will be achieved correspondingly. When the wavelength of the working FBG shifts which includes the sensing information, FBG interrogation can be realized both in wavelength and time domain.