Performance of Dispersion-Compensated Optical Transmission Systems Based on Different Electrical Drivers

In this article, the simulation results have been presented for dispersive optical communication with different electrical drivers. The length of single-mode fiber has been put in a run that is compensated by dispersion-compensated fiber. The results have been presented and it is observed that of all the electrical drivers, the NRZ rectangular is best suited for dispersive optical communication systems. For this electrical driver, the parameters like BER remain constant and low. For other drivers, the BER decreases more for RZ super-Gaussian. Similarly, the Q factor increases with runs for all types of drivers except for NRZ rectangular, for which it decreases. For all the drivers, it is clear that as the runs are varied, the eye opening penalty increases, that is, there is less eye opening as the length of single-mode fiber is increased. It is also seen that the dispersion-compensated fiber compensates for the dispersion very effectively irrespective of the type of driver. Of the two formats, return to zero (RZ) and non-return to zero (NRZ), the earlier has more eye-opening penalty as the distortion is more and is clearly visible in all the rectangular, super-Gaussian, and raised cosine RZ formats. Of the three RZ formats, it is observed that RZ rectangular has the least eye-opening penalty. The non-return to zero format has less distortion and, of the two rectangular and raised cosine, the NRZ rectangular has less eye-opening penalty.     

Performance of Dispersion-Compensated Optical Transmission Systems Based on Different Electrical Drivers

In this article, the simulation results have been presented for dispersive optical communication with different electrical drivers. The length of single-mode fiber has been put in a run that is compensated by dispersion-compensated fiber. The results have been presented and it is observed that of all the electrical drivers, the NRZ rectangular is best suited for dispersive optical communication systems. For this electrical driver, the parameters like BER remain constant and low. For other drivers, the BER decreases more for RZ super-Gaussian. Similarly, the Q factor increases with runs for all types of drivers except for NRZ rectangular, for which it decreases. For all the drivers, it is clear that as the runs are varied, the eye opening penalty increases, that is, there is less eye opening as the length of single-mode fiber is increased. It is also seen that the dispersion-compensated fiber compensates for the dispersion very effectively irrespective of the type of driver. Of the two formats, return to zero (RZ) and non-return to zero (NRZ), the earlier has more eye-opening penalty as the distortion is more and is clearly visible in all the rectangular, super-Gaussian, and raised cosine RZ formats. Of the three RZ formats, it is observed that RZ rectangular has the least eye-opening penalty. The non-return to zero format has less distortion and, of the two rectangular and raised cosine, the NRZ rectangular has less eye-opening penalty.     

Compensating spectral loss variations in EDFA amplifiers for different modulation formats

In this paper, we investigate the performance of the optical system consisting of chain of EDFA amplifiers for different data formats such as non-return-to-zero (NRZ), return to zero (RZ) and Manchester. Their effect on the spectral loss variations produced in fiber output is analyzed. We show that when the RZ raised cosine and Manchester raised cosine modulation formats are used, the non-linear ties are produced in power spectrum plots which severely distort the signals obtained at the output of the chain of the EDFA amplifiers. On the other hand, the NRZ raised cosine modulation format best compensates the spectral loss variations in the power spectrum plots obtained at the output. We further show that NRZ raised cosine has good eye opening as compared to other modulation formats.     

New design of spectral amplitude coding in OCDMA with zero cross-correlation

A zero cross-correlation (ZCC) code is proposed to reduce the impact of system impairment and multiple access interference (MAI) in spectral amplitude coding optical code division multiple access (SAC-OCDMA) system. Bit-error-rate (BER) performance is derived taking into account the effect of some noises. The key to an effective OCDMA system is the choice of efficient address codes with good or almost zero correlation properties for encoding the source. The use of ZCC code can eradicate phase induced intensity noise (PIIN) which will contribute to better BER. Thus, we demonstrate, theoretically, the performance of optical ZCC code. It is shown that optical ZCC code can accommodate more users simultaneously for the typical error rate of optical communication system of 10⁻⁹. The result indicates that the established system not only preserves the capability of suppressing MAI, but also improves bit-error-rate performance as compared to the conventional coders.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical soliton transmission links at different chirps

This paper presents the comparative investigation and suitability of various data formats for optical soliton transmission links at 10 Gb/s for different chirps (−0.7 to 0.7). Here the investigations focused on data formats: NRZ, RZ soliton, RZ raised cosine and RZ super Gaussian. The comparative results and suitability of data formats is based on various performance measures such as Q-factor, eye opening, BER and jitter. It has been indicated that RZ super Gaussian yields the highest value of Q (34.08 dB), good eye opening and lowest BER.     

Comparative investigation and suitability of various data formats for 10 Gb/s optical AWG multiplexer and AWG demultiplexer based transmission links

In this paper, we have analyzed the performance and feasibility for the metropolitan area network based on arrayed waveguide grating (AWG) multiplexers and arrayed waveguide grating (AWG) demultiplexers operating at the bitrate of 10 Gb/s. In the network, the data is successfully transmitted to a distance of 50 km with a very low BER of 1 × 10⁻⁴⁰ thus improving the performance over AWG star based networks. Here, we have observed that arrayed waveguide gratings based multiplexers and demultiplexers for WDM applications prove to be capable of precise multiplexing and demultiplexing of a large number of channels with relatively low losses. This paper also presents the comparative investigation and suitability of various data formats like NRZ Rectangular, NRZ Raised cosine, RZ Rectangular, RZ Raised cosine and RZ super Gaussian for optical transmission link. It has been shown that RZ Raised cosine yields the highest value of Q, good eye opening and lowest BER.     

Minimizing correlation effect using zero cross correlation code in spectral amplitude coding optical code division multiple access

The use of minimal multiple access interference (MAI) in code design is investigated. Applying a projection and mapping techniques, a code that has a zero cross correlation (ZCC) between users in optical code division multiple access (OCDMA) is presented in this paper. The system is based on an incoherent light source—LED, spectral amplitude coding (SAC), and direct detection techniques at the receiver. Using power spectral density (PSD) function and Gaussian approximation, we obtain the signal-to-noise ratio (SNR) and the bit-error rate (BER) to measure the code performance. Making a comparison with other existing codes, e.g., Hadamard, MFH and MDW codes, we show that our code performs better at BER 10⁻⁹ in terms of number of simultaneous users. We also demonstrate the comparison between the theoretical and simulation analyses, where the results are close to one another.     

PIN versus Avalanche photodiode gain optimization in zero cross correlation optical code division multiple access system

In this paper, we show details of zero cross correlation (ZCC) code development and investigate performance by measuring bit-error-rates compared to other optical code division multiple access (OCDMA) codes using Avalanche photodiode (APD) and PIN photodetector. We present a configuration to determine how optical OCDMA systems can be applied with PIN and APD photodetector. Analysis of Avalanche photodiode gain optimization is discussed in ZCC code system. We also present analytical and numerical theoretical results for data transmission of spectrally encoded incoherent OCDMA signal and how signal-noise is being affected by using these two photodetectors.     

Performance analysis of NRZ, RZ, CRZ and CSRZ data formats in 10 Gb/s optical soliton transmission link under the impact of chirp and TOD

This paper presents the performance analysis of non-return-to-zero (NRZ), return-to-zero (RZ), chirped return-to-zero (CRZ) and carrier suppressed return-to-zero (CSRZ) data formats in optical soliton transmission link under the impact of chirp and third-order dispersion (TOD). The performance of these data formats has been analyzed on the basis of certain performance metrics, viz, bit error rate (BER), Q² (dB), OSNR, eye opening, etc. It has been reported here that the performance of CRZ and CSRZ modulation format is better as compared to NRZ and RZ in a soliton transmission link. Further, CSRZ modulation format has been found to deliver optimum performance on the basis of performance evaluation metrics reported in this paper. In case of NRZ and CSRZ, comparatively narrow power spectrum has been observed. Best eye opening, highest value of Q² (dB) of 18 dB and lowest value of BER of the order of 10⁻¹⁶ has been reported in case of CSRZ among the considered data formats. The results have been obtained by varying noise figure from 3.0 to 9.0. No considerable effect of noise was observed. It was observed that at very narrow and ultra short pulse width, OSNR value suffers heavily and reduced to even negative values in dB, thus inducing a high degree of OSNR power penalty. The results were obtained by varying chirp factor from −0.6 to +0.6. Negative chirp resulted in improved OSNR as compared to positive chirp. RZ data format yielded a broader optical spectrum, comparatively low spectral efficiency and poor OSNR thus it was found that RZ format is not suitable for optical soliton transmission under the impact of chirp and TOD.     

Performance analysis of optical WDM system based on unequal spaced channel allocation (USCA) scheme

Unequal spaced channel allocation (USCA) is a technique to reduce Four wave mixing (FWM). In this paper, system performance of 8 channel WDM system considering different optical transmitter formats (RZ, NRZ, Raised cosine and Gaussian) using USCA has been evaluated in terms of Q-factor. The simulation results reveal that four wave mixing is minimum for NRZ format. Also the effect of changing the laser power and increasing the bit rate has been observed.     

一种跳频扩时码的构造及性能分析

以一维二次同余码(QCC)作为扩时模式，以光正交码(OOC)和QCC码作为频域跳频模式，通过时域和频域的组合，构造了适用于光码分多址(OCDMA)系统的QCC/QCC和QCC/OOC 2种跳频扩时码，并对码的容量及其相关性进行了分析。与一维QCC码相比，QCC/QCC跳频扩时码的容量扩大了p 1倍（p为码重），相关性得到改善，并且码字异相自相关限λa=1，互相关限λc=2；QCC/OOC跳频扩时码具有更大的码容量和更好的相关性，码字异相自相关限λa=0，所有码字按一定规律可分成p 1组（p为码重），每组内码字的互相关限λa=1，不同组间码字的互相关限λa=2。所得结果为光码分多址系统中跳频扩时码的构造提供了一种新的方法。     

一种新的大容量的二维光正交码

构造了一种扩展的双曲线性同余码(EHLC)并分析了其码字性能.用该码作为时间扩频伪随机序列和以素数码(PC)作为波长跳频伪随机序列,再构成一种新的二维光正交码EHLC/PC.然后分析了EHLC/PC码字的性能,并与EQC/PC作了比较.相比之下,前者的互相关性能略有下降,但码字容量大大增加.因此,EHLC/PC适合于用户数较多的OCDMA系统.     

Analysis of intensity modulation performance in WDM-PON network

This paper mainly does research and analysis on anti-dispersive performance and anti-nonlinear performance for intensity modulation formats such as NRZ, RZ, CS-RZ, DRZ, MD-RZ in 40 Gbps high-speed single-channel optical transmission system. It compares the five pattern modulation formats in dispersion tolerance, nonlinear tolerance, and advantages and disadvantages in transmission distance. Anti-nonlinear effect ability of CSRZ and RZ are stronger than that of NRZ code; in the single-channel transmission system, DRZ and improved modulation format MDRZ have better resistance for anti-nonlinear performance, so they are suitable for long-distance transmission. RZ has the minimum dispersion tolerance. NRZ has higher spectrum efficiency than RZ, and thus have a better dispersion tolerance. CSRZ code has higher spectral efficiency, higher dispersion tolerance and nonlinear tolerance than RZ code, making it more suitable for long distance transmission.     

A novel encoder/decoder design scheme utilizing differential detection in OCDMA systems

In this paper, we report the use of differential detection in optical code-division multiple access (OCDMA) systems which use encoders and decoders based on unbalanced codes and utilize bipolar modulation/differential detection to demonstrate a significant improvement in system performance. Differential detection has been reported earlier also requiring a large number of one-chips in the code for (balanced codes) or with unbalanced codes with very long temporal dimensions requiring a large number of delay elements (either the delay lines in the ladder-type structures or the gratings in the multiple fiber gratings) making the encoder/decoder structures. We use single pulse per row codes to design our system and carry out the simulations for showing the results. The improved BER performance is achieved that can be traded for increasing the number of codes. Using optical simulation tool, the OCDMA system has been simulated for four users. The results of this system utilizing differential detection and another system that uses the same coding scheme but employing direct detection, for the same number of interfering users, are shown for comparison. The BER and the power penalty plots are shown for the two systems. Also, it is shown that performance degradation occurs due to the linear and non-linear effects of the fiber medium. The BER worsens more rapidly with link length for direct detection case, whereas for differential detection with an initial improvement of 8 dB, the increase in BER is insignificantly small for a link length of 500 km.     

Design and implementation of 2-dimensional wavelength/time codes for OCDMA

In this paper, two-dimensional (2D) wavelength/time codes are designed and implemented. The 2D codes are constructed by a technique based on folding of Golomb rulers. The performance evaluation of OCDMA system based on wavelength/time code has been analyzed by measuring the values of bit error rates and eye diagrams for different number of active users. It is shown that eye opening decreases and BER increases with increase in number of active users. It is also shown that BER further increases with increase in number of active users when number of decoders increases on receiver side. Hence, it is concluded that multiple access interference (MAI) is the dominant source of BER and there is graceful degradation in system performance when number of simultaneously active users increases. The received optical power is also measured at different transmission distance. It has been observed that received optical power decreases with increase in length of fiber due to attenuation.     

Simulative analysis of co-existing 2.5 G/10 G asymmetric XG-PON system using RZ and NRZ data formats

In this paper, a fiber optic communication system has been employed using co-existing 10 G/2.5 G asymmetric gigabit passive optical network (XG-PON) architecture. In this system, bidirectional optical fiber has been used for upstream and downstream data transmission. The system performance has been investigated for non-return-to-zero (NRZ) and return-to-zero (RZ) data formats operating at varying bit rates by varying the length of the fiber for analyzing the feasibility of this co-existence. The results have been compared for NRZ and RZ formats for upstream and downstream data in terms of Q value and eye opening. It is observed that RZ modulation format is superior as compared to conventional NRZ format and the faithful transmission of signal has been carried up to 90 km at 1577 nm for downstream and 140 km at 1270 nm for upstream.     

一种基于扩展素数码和单重合序列的二维光正交码EPC/OCS

以扩展素数码(EPC)作为时间扩频伪随机序列,单重合序列(OCS)作为波长跳频伪随机序列,构造了一种新的二维光正交码EPC/OCS,并分析了码字的互相关性能.与修正素数跳频码MPHC相比,EPC/OCS的波长数并不局限于素数,可以是任意整数,不仅构造灵活,而且可充分利用MW OCDMA系统的有效波长数.当系统的有效波长数大于某个素数时,EPC/OCS不仅码字容量大于MPHC,而且互相关性能也有所改善.理论分析表明,EPC/OCS可降低MW OCDMA系统误码率.     

基于2D-OOC的OCDMA系统的地址码结构研究

提出了二维光正交码 (2D OOC)设计方案 ,围绕光码分多址 (OCDMA)技术实用化的两个主要指标—最大并发用户数和系统误码率的改进和提高 ,系统地研究了基于 2D OOC的OCDMA的性能 ,分析了 2D OOC码字的相关性 ,导出了系统的最大用户容量 ,详细研究了 2D OOC系统以多址干扰为主的系统误码率 .研究表明 :较之一维时域扩频码或一维谱域扩频码 ,2D OOC系统性能大大提高 ,在大信息量传输时 ,适当选择码长和码重 ,系统总容量可高达Tbits/s量级 ,性能优于基于 1D OOC的OWDM和OCDMA混合系统 .     

基于2D-OOC的OCDMA系统的地址码结构研究

提出了二维光正交码(2D-OOC)设计方案,围绕光码分多址(OCDMA)技术实用化的两个主要指标-最大并发用户数和系统误码率的改进和提高,系统地研究了基于2D-OOC的OCDMA的性能,分析了2D-OOC码字的相关性,导出了系统的最大用户容量,详细研究了2D-OOC系统以多址干扰为主的系统误码率.研究表明:较之一维时域扩频码或一维谱域扩频码,2D-OOC系统性能大大提高,在大信息量传输时,适当选择码长和码重,系统总容量可高达Tbits/s量级,性能优于基于1D-OOC的OWDM和OCDMA混合系统.     

Implementation and performance analysis of three dimensional (3D) space/wavelength/time single pulse per plane codes with direct detection

In this paper, we present space/wavelength/time single pulse per plane (SPP) codes with direct detection (SPPDD) and implemented it as two dimensional codes by using W²T scheme. We analyze these codes by varying the number of space channels (S) and keeping other two dimensions, wavelength (W) and time (T) constant and report that it gives better results when (W > S). It is found that the space channels S = 2 and S = 3 provide better BER rate than other space channels and also analyze these 3D codes by using different data modulation formats. It is found that OCDMA system with NRZ data modulation format performs better than RZ.