A full-duplex radio-over-fiber link with 12-tupling mm-wave generation and wavelength reuse for upstream signal

A full-duplex radio-over-fiber (RoF) link with a novel scheme to generate 60 GHz mm-waves from a 5 GHz RF signal source is investigated. In the RoF downlink, the required frequency of the RF oscillator is reduced greatly. Since the optical carrier is not modulated by downstream data, part of it is reused to carry upstream data and the upstream data is transmitted to the central station using optical single-sideband modulation. In this way, a single wavelength is used for both downstream and upstream transmissions. Based on this scheme, a full-duplex RoF link is built and its transmission performance is analyzed. Theoretical analysis and numerical simulation show that the downstream signal cannot only eliminate code form distortion caused by time shift of the code edges, but also reduce the influence of the fading effect as the 60 GHz DSB optical mm-wave signal is transmitted along the fiber, and the upstream signal is immune to both fading effect and time shift of the code edges.     

Photonic generation of 60 GHz-band vector signals for RoF systems based on optical vector signal down-conversion

A novel photonic method of 60 GHz-band vector signal generation for RoF systems based on optical vector signal down-conversion is proposed and experimentally demonstrated in this paper. In the proposed method, the target vector signals are first generated in the optical domain with the help of mature commercial optical devices and then directly distributed to the base stations (BSs) through the fiber link. The generated vector signals can be automatically down-converted to the 60 GHz band in the BSs after O/E conversion, and then directly transmitted to the users without any further processing. With the proposed method, higher spectrum efficiency and system capacity will be obtained compared with the traditional OOK RoF systems while almost no extra system complexity and cost is brought in. According to the characteristics of different types of vector signals, two particular modulation schemes are provided, which are then verified by corresponding simulations and experiments. In the experimental 60 GHz RoF system, the 622 MSym/s 60 GHz-band 8-QAM and 4-QAM signals generated with two different schemes respectively are successfully transmitted over 50 km SMF and 5 m wireless channel without any compensation, and the power penalty are both about 1.7 dB at the BER of 10^− 9.     

A novel approach for simultaneous millimeter wave generation and high bit rate data transmission for Radio over Fiber (RoF) systems

We propose a novel method for simultaneous transmission of OC-192 (9.95328 Gbps) digital data and 60 GHz RF generation in a Standard Single Mode Fiber (SSMF) link utilizing Stimulated Brillouin Scattering (SBS). The system comprises of a 1550 nm DFB Laser diode, Mach Zehnder modulator (MZM), 50 km SSMF and Optical receiver. The receiver includes laser diode for optical pump, a regenerator for data retrieval and a RF bandpass filter for RF generation. This system requires minimum number of RF and optical components for the generation of 60 GHz RF. The remotely generated 60 GHz RF signal may be used for wireless transmission of data. The entire link is simulated in Optisystem software to analyze the system performance.     

A bidirectional 60 GHz RoF system based on FWM in a semiconductor optical amplifier

In this study, a bidirectional 60 GHz RoF systems based on four-wave mixing (FWM) in semiconductor optical amplifier (SOA) is proposed. Two key techniques are included in such a scheme, namely, generation of 60 GHz modulating signals and distribution of 60 GHz local oscillator. The analytical model is theoretically analyzed and then confirmed by numerical simulations. Results of this study demonstrate that such a scheme can offer realistic solutions to support future mobile broad-band applications.     

Cost-effective and dispersion-tolerant cascade modulation for millimeter-wave-over-fiber applications

In millimeter-wave-over-fiber (MWoF) feeder systems, the received millimeter-wave signals at the remote antennas (RAs) can suffer from signal fading by chromatic dispersion of optical fiber. This can be substantially mitigated by Mach-Zehnder modulator (MZM) based photonic up-conversion technique. In this technique, the data signals at intermediate frequency (IF) are frequency up-converted to millimeter-wave frequency by an MZM biased at its transmission null point. However, this scheme requires a costly, high-speed MZM, which will hinder the widespread of this technique for cost-sensitive MWoF applications. Hence, we propose and demonstrate a cost-effective way of reducing the cost of MWoF optical transmitters based on photonic up-conversion technique. We employ a dual wavelength source composed of a directly modulated laser and a polarimetric filter. This source is used to generate a millimeter-wave tone signal and to frequency up-convert the IF data signals to millimeter-wave frequency. The dual wavelength source is also shared with numerous RAs for further cost reduction. Our experimental demonstration performed with 30 Msymbol/s 16-quadrature amplitude modulation signals shows that we can transmit the 20 GHz millimeter-wave signals over 25 km standard single-mode fiber without any transmission penalty.     

All-optical synchronization of a 40 GHz self-pulsating distributed Bragg reflector laser to return-to-zero 10, 20 and 40 Gbit/s data streams

This paper presents experimental investigations of the all-optical synchronization of a distributed Bragg reflector (DBR) laser self-pulsating at 40 GHz on various injected bit-rate signals. Even though there is no modulation applied to this laser, it exhibits a modulation of its output emission, measured at 39.7 GHz with a linewidth of 30 MHz. Such performance is exploited in all-optical clock recovery for a return-to-zero data stream at 40 Gbit/s. The SP-DBR laser wavelength and the injected signal wavelength are 10 nm apart. All-optical synchronization is demonstrated at 40 Gbit/s with a linewidth of less than 20 MHz for injected signals at 10 and 20 Gbit/s, respectively. Thus the SP-DBR laser proves to be very versatile and can be synchronized on various bit-rate data signals.     

Impact of interferometer delay time on the performance of ODSB-SC RoF system with wavelength interleaving

In this paper, we investigate the impact of interferometer delay time in a 5 Gb/s optical double sideband-suppressed carrier (ODSB-SC) RoF system transmitting two wavelength interleaved radio frequency (RF) signals at 10 and 15 GHz over an optical fiber. Here, an optical Mach–Zehnder modulator is used for both optical carrier suppression and signal modulation. At the receiver, delay interferometer is used for the separation of RF frequency signals. We analyze the performance of the RoF system by varying the value of delay time of interferometer from 0.02 to 0.14 ns. The result shows that the RoF system performance is optimum for the time delay of 0.1 ns. Further, the optical spectrums, RF spectrums and eye diagrams of two interleaved RF signals have been compared.     

All optical arbitrary waveform generation by optical frequency comb based on cascading intensity modulation

We propose and experimentally demonstrate an all optical arbitrary waveform generation by optical frequency comb (OFC) based on cascading intensity modulation. By selecting spectral lines of interest from OFC through optical filters, 10 GHz, 20 GHz, and 60 GHz sinusoidal signals with low phase noise and more complex waveforms, including ultra-short pulse, half-wave cosine, and single frequency modulated MMW signals, are generated easily.     

Single AWG based clock extraction from WDM signals with mixed formats and mixed bit-rates

A simple and flexible simultaneous clock extraction for WDM signals with mixed modulation formats and bit-rates is proposed and demonstrated using a single commercial arrayed waveguide grating (AWG), which acts both detuned multi-channel filter and demultiplexer for the input signals. By using an AWG with 100 GHz spacing, clock extraction from transmitted multi-channel nonreturn to zero (NRZ) and NRZ differential phase shift keying (NRZ-DPSK) signals at mixed bit-rates from 10 to 40 Gb/s with 200 GHz spacing is achieved simultaneously. By cascading a clock recovery module, clock signal can be easily recovered from the preprocessed signals with enhanced clock tones.     

Optical demultiplexing of millimeter-wave subcarriers for wireless channel distribution employing dual wavelength FBGs

An optical mm-wave demultiplexer is presented. Double sideband modulation with suppressed optical carrier and filtering properties of dual overwritten fiber Bragg gratings are the fundamentals for optical demultiplexing of mm-wave radio-on-fiber signals: using a single optical carrier, Millimeter-wave signals of 20 and 40 GHz frequencies carrying independent data are created, transmitted over fiber, demultiplexed and wireless distributed to be detected and data recovered in a mobile unit. Double sideband modulation with suppressed optical carrier yields no power penalty due to chromatic dispersion, while the filtering properties of the dual overwritten fiber Bragg gratings allow less than −40 dB electrical power interchannel leakage. Independent 2.5 Gb/s On-Off-keyed data have been successfully transmitted through the 20 and 40 GHz channels.     

Photonic generation of a microwave signal by employing a microfiber ring resonator

A novel approach to generate microwave signals is presented by employing a microfiber ring resonator. The microfiber ring resonator is assembled with a microfiber fabricated by heating and drawing standard single-mode fiber. By cascading microfiber ring resonator acted as a comb filter with a tunable bandpass filter, a wavelength-tunable dual-wavelength single longitudinal-mode laser is achieved. A microwave signal at 15.57 GHz with the linewidth of less than 21 kHz is demonstrated by beating the two wavelengths at a photodetector.     

A novel MI-insensitive and filterless frequency octupling scheme based on two parallel dual-parallel Mach–Zehnder modulators

A novel MI-insensitive and filterless frequency octupling scheme based on two parallel dual-parallel Mach–Zehnder modulators (DP-MZMs) is proposed. The proposed scheme is not sensitive to modulation index and relatively strong MMW signal with good radio frequency spurious suppression ratio (RFSSR) can be obtained without strict requirement on modulation index. Filterless feature makes the scheme quite suitable for wavelength division multiplexing (WDM) applications. For verification, a 60 GHz millimeter wave with 44 dB RFSSR is generated from a 7.5 GHz radio frequency wave by simulation. Performance of the proposed scheme has been characterized under different conditions including DC-bias drifts of MZMs, different amplitudes of RF inputs and different extinction ratios of MZMs.     

EAM-SOA millimeter-wave frequency up-converter for radio-over-fiber applications

We present an optical scheme for photonic frequency up-conversion at the millimeter-wave bands based on Semiconductor Optical Amplifier. The proposed scheme modulates the bias current with the Intermediate Frequency in order to achieve frequency mixing of an incoming optical signal modulated with the Local Oscillator. Theory indicates that the proposed scheme supports data bandwidths in the tens of GHz for LO values above 10 GHz. This scheme allows for photonic integration of the considered optical devices. A laboratory demonstration of the scheme for up-conversion to the 40 GHz band, using narrow-band IF signals, showed relatively low thresholds for the optical input power and bias current level to achieve error free operation: − 14.5 dBm 100 mA for a 64-QAM signal. Spurious-Free Dynamic Range showed an acceptable performance, with a linearity about 52.5 dB·Hz^2/3 for an optical input power of − 6 dBm.     

Mode locking of an erbium-doped fiber laser with intra-cavity polarization modulation

Erbium-doped fiber lasers are normally actively mode-locked through amplitude modulation or phase modulation. In this paper, we demonstrate that the laser can also be mode-locked by employing polarization modulation with a polarization-dependent cavity loss. We obtain a nearly transform-limited mode-locked pulse train at 10 GHz repetition rate with timing jitter as low as 164 fs. The timing jitter is only limited by the timing jitter of the driving signal.     

Photonic generation of microwave signals using dual-wavelength single-longitudinal-mode fiber lasers

Photonic generation of microwave signals is demonstrated with a dual-wavelength single-longitudinal-mode erbium-doped fiber ring laser. Microwave signal with a frequency of 21.07 GHz is obtained by aligning the reflection band of a uniform fiber Bragg grating to the two transmission peaks within a fiber Bragg grating-based Fabry-Perot filter. Stable dual-wavelength single-longitudinal-mode operation is guaranteed by means of the combined filtering effect of a saturable absorber and the Fabry-Perot filter. This approach provides an effective solution to the photonic generation of high-frequency microwave signals.     

Characterization of 60 GHz Multi Quantum well passively mode-locked laser under optical self-injection locking

The quality and pulse compression of the 60 GHz millimeter wave signals generated by 750 μm long InAlGaAs Multi Quantum Well (MQW) passively mode locked laser under free running and optical self-injection locked conditions are experimentally characterized in terms of longitudinal modes under certain bias currents that range from 24 mA to 90 mA. Initially, the MQW laser is characterized in free running condition with no external injection. The measurements reflect that the free spectral range of laser under test is around 61 GHz and exhibit more than 22 lasing modes. The laser is then integrated into low phase noise self-injection locking oscillator by feeding a part of output RF signal back into the laser cavity to enhance passive mode locking. By doing so the microwave line width of our laser is reduced from 900 kHz to 24 kHz with significant increase in output of resultant beat tones which exhibits strong passive mode locking. This is the first time that the free running microwave line width of MQW laser is reduced up to this level. It is evident from our experimental investigation that as we increase the power and phase correlation between different longitudinal modes inside laser cavity through optical self-injection, the strength of the passively mode locked mechanism is significantly increased and the phase noise of radio frequency signal is drastically reduced.     

A novel tunable optical oscillator for broadband signals

A tunable optical oscillator that generates signals at the micro- to millimeter-wave band for wireless communication applications is suggested. It uses directly modulated semiconductor lasers, in which sideband modes and four-wave mixing (FWM) conjugate modes are injection locked by the simple control of the applied modulation power. The signals at 15 GHz with phase noise of below ?95 dBc/Hz at an offset frequency of 100 kHz were experimentally obtained. The frequency of the generated signal is tunable, and the maximum achievable signal frequency is limited mainly by the bandwidth of the receiver.     

Atomic and molecular spectroscopy with a continuous-wave, doubly resonant, monolithic optical parametric oscillator

Doppler-broadened atomic and molecular spectra were observed with a one octave tunable, continuous-wave, doubly resonant, monolithic optical parametric oscillator (OPO) using 5% MgO-doped LiNbO₃ as a non-linear crystal with a birefringent phase-matching configuration. By tuning the frequency of a pump laser, longitudinal mode selection over 20 successive modes, corresponding to a 60 GHz span, was possible, owing to the simple structure of the monolithic OPO. Continuous frequency tuning was achieved using an external waveguide-type electrooptic phase modulator (EOM). By changing the modulation frequency of the EOM, frequency tuning of the optical sidebands over 12 GHz was possible, which is larger than the one free spectral range of the monolithic cavity of 3 GHz. We could observe the Cs-D₁ (894 nm), Cs-D₂ (852 nm), Rb-D₁ (795 nm), acetylene R9 (1520 nm) and P9 (1530 nm) transitions with the single monolithic OPO.     

64 GHz optical millimeter-wave generation by octupling 8 GHz local oscillator via a nested LiNbO3 modulator

A novel scheme to generate a 64 GHz optical millimeter (mm)-wave via a nested LiNbO₃ Mach-Zehnder modulator with an 8 GHz local oscillator is proposed and simulated. Since the frequency response of the modulator and the local oscillator frequency are greatly reduced, the bandwidth requirements of the optical and electrical components in the transmitter are significantly decreased. The simulation results show that the generated optical mm-wave signal maintains good performance even after being transmitted over 20 km standard single-mode fiber.     

A tunable fiber parametric oscillator for the 2 μm wavelength range employing an intra-cavity thulium doped fiber active filter

We report an efficient fiber parametric oscillator operating in the wavelengths range of 1.97 μm to 2.14 μm. The oscillator is based on narrow band parametric amplification and employs a thulium doped fiber placed at the loops end as an intra-cavity active filter. The filter eliminates any signal generated by stimulated Raman scattering which inherently accompanies the parametric process. Short wavelength parametric oscillations and the pump signal are also absorbed. Only the long wavelength parametric oscillations can build up in the resonantly pumped system which emits 4 ns pulses at ~ 1 MHz with a maximum peak pulse power of 20 W.