Mode locked Er-doped fiber laser with single-wall carbon nanotube saturable absorber

A mode locked Er-doped fiber laser based on a single-wall carbon nanotube saturable absorber is demonstrated. A high quality single-wall carbon nanotubes （SWCNTs） absorber film is fabricated by a polymer composite. The pulse duration is 488 fs with 9.6-nm spectral width at the center of 1564 nm. The repetition rate is 30.4 MHz. The maximum output power is 3 mW. And the single pulse energy is 0.1 nJ.     

碳纳米管锁模双包层光纤激光器的实验研究

本文采用双包层掺镱光纤作为增益介质,用单壁碳纳米管作为饱和吸收体,获得最高输出功率为336 mW的锁模脉冲激光.用飞秒激光诱导水击穿法直接在单模光纤上制备出D形区,通过在D形光纤上滴涂单壁碳纳米管溶液,成功制备出碳纳米管饱和吸收体,并对其饱和吸收特性进行测试,发现其调制深度为27％.利用该饱和吸收体作为锁模器件,制备出具有环形腔结构的锁模光纤激光器.当抽运功率为4W时,获得了脉宽为93.8 fs,中心波长为1083.8 nm,3 dB谱宽为8.6 nm,重复频率为5.59 MHz,平均功率为336 mW的飞秒脉冲激光输出.     

石墨烯可调谐被动调Q掺铒光纤激光器

基于光学沉积方法,制备了石墨烯可饱和吸收体,并利用此可饱和吸收体搭建了环形腔结构的被动调Q掺铒光纤激光器,实现了稳定的调Q激光脉冲输出,其重复频率为5.1~14.2 kHz,最窄激光脉冲宽度为8 s,最大平均功率为162.3 W,且通过调节偏振控制器,中心波长在1556~1558 nm可调。     

147 fs碳纳米管倏逝场锁模全光纤掺铒光纤激光器

利用化学腐蚀法在光纤包层表面成功制备了调制深度为3.9%的单壁碳纳米管饱和吸收体.组建了环形腔结构的全光纤掺铒光纤激光器,以制备的单壁碳纳米管薄膜为锁模元件,利用倏逝场锁模实现了锁模输出.锁模脉冲的中心波长为1556 nm,3 dB光谱带宽为24 nm,脉冲宽度为147 fs,重复频率为150 MHz.在520mW抽运功率下,平均输出功率为21 mW,相应的单脉冲能量为0.14 nJ.     

氧化石墨烯被动调Q掺铒光纤激光器

报道了基于氧化石墨烯的被动调Q掺铒光纤激光器。激光器采用环形腔结构,调Q器件为自制的氧化石墨烯可饱和吸收镜。泵浦功率在81~505 mW范围内时,得到了重复频率68~124 kHz的稳定的调Q脉冲输出,脉宽为0.47~1.60 s。由于泵浦功率限制,激光器最大输出功率为10 mW, 相应单脉冲能量为80.6 nJ。此种基于氧化石墨烯可饱和吸收体的被动调Q光纤激光器体积小、成本低廉、结构简单、稳定性高、光束质量高,具有广阔的应用前景。     

基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器

报道了一种基于石墨烯可饱和吸收体的纳秒锁模掺铥光纤激光器.该激光器采用环形腔结构,利用自制的三层石墨烯薄膜作为可饱和吸收体实现锁模.同时在腔内插入一个窄带光纤光栅,约束腔内起振的纵模数,适当调节抽运功率和偏振控制器的角度,得到了重复频率为3.8 MHz、脉宽在3.8—94.3 ns之间灵活可调的2μm纳秒锁模脉冲输出,整个脉宽调节范围超过90 ns.此外,由于获得的兆赫兹纳秒锁模脉冲时间带宽积在49—1119范围内,即存在强烈的啁啾,因而可作为2μm波段啁啾脉冲放大系统中的种子源使用.     

Multi-wavelength Q-switched erbium doped fiber laser with a short carbon nanotube based saturable absorber

We demonstrate an all-fiber passively multi-wavelength Q-switched Erbium doped fiber laser (EDFL) based on a short Carbon Nanotube based saturable absorber. With the saturable absorber connected in a longer standing wave based fiber laser cavity, stable single, dual, and multiple wavelength Q-switched low threshold EDFL are achieved. Experimental results show that the output pulse of the filtered single wavelength has the same repetition rate as that of the multi-wavelength output while its average output power is lower than that of the multi-wavelength output.     

Zinc-oxide/PDMS-clad tapered fiber saturable absorber for passively mode-locked erbium-doped fiber laser

We propose and demonstrate a passively mode-locked erbium-doped fiber laser(EDFL) based on zincoxide/polydimethylsiloxane(Zn O/PDMS) saturable absorber(SA) that evanescently interacts with the light on a tapered fiber. The Zn O/PDMS composite is coated on the whole surface of the tapered fiber to guarantee the maximum efficiency of the SA device, with a measured insertion loss of 0.87 d B and a modulation depth of 6.4%. The proposed laser can generate soliton mode-locking operation at a threshold power of 33.07 m W. The generated output pulse yields a repetition rate and pulse width of 9.77 MHz and 1.03 ps, respectively. These results indicate that the proposed Zn O/PDMS-clad tapered fiber could be useful as an efficient, compatible, and low-cost SA device for ultrafast laser applications.     

Single-walled carbon nanotubes on side polished fiber as a universal saturable absorber for various laser output states

We demonstrated four different laser operational states in the same passive fiber ring laser cavity by controlling solely the polarization state in a saturable absorber. The demonstrated laser operational states were continuous wave, mode-locking, Q-switching, and Q-switched mode-locking. The saturable absorber was fabricated by spin-coating a single-walled carbon nanotubes (SWCNT)/polymer composite on a side polished fiber providing enhanced nonlinear interaction with the SWCNT. The wide tuning range of the saturable absorber allows the simple means to generate different forms of laser output from a single laser cavity.     

Low-repetition-rate,all-polarization-maintaining Yb-doped fiber laser mode-locked by a semiconductor saturable absorber

A low-repetition-rate, all-polarization-maintaining(PM)-fiber sub-nanosecond oscillator is presented, which is simple and low-cost, composed of standard components. The ring cavity is elongated by 114-m-long standard PM fiber, and passively mode-locked by a fiber pigtailed semiconductor saturable absorber. Linearly polarized pulses with 1.66 MHz repetition rate and 22 dB polarization extinction ratio are generated at a wavelength of 1030 nm, which is determined by an intracavity filter. In addition, to demonstrate that the oscillator is a good seed for high energy pulse generation, an all-fiber master oscillator power amplifier is built and amplified pulses with energy about 2 μJ are obtained.     

Periodic intensity variations on the pulse-train of a passively mode-locked fiber ring laser

We investigate the evolvement of the periodic intensity variations of the pulse-train in a fiber ring laser mode-locked by the nonlinear polarization rotation technique. It is found that the phenomenon of such intensity fluctuations is related to the orientation of the polarization controllers when the pump power is fixed. The numerical results show that the mechanism of the periodic intensity variations is caused by the interaction of the nonlinear polarization rotation and the passive polarizer in the cavity.     

Raman fiber laser pumped by a semiconductor disk laser and mode locked by a semiconductor saturable absorber mirror

A 1.6μm mode-locked Raman fiber laser pumped by a 1480nm semiconductor disk laser is demonstrated. Watt-level core pumping of the single-mode fiber Raman lasers with low-noise disk lasers together with semiconductor saturable absorber mirror mode locking represents a highly practical solution for short-pulse operation.     

Bound soliton pulses in passively mode-locked fiber laser

A passively mode-locked soliton fiber ring laser was successfully demonstrated, and bound soliton pulses with an FWHM pulsewidth of 326 fs and fixed separation of 938 fs were first observed. The number of bound soliton pairs in the cavity can be controlled under lower pump power. The transmission effects were investigated by injecting bound soliton pulses into a single mode fiber.     

Stable single- and dual-wavelength fiber laser mode locked and spectrum shaped by a Fabry-Perot saturable absorber

We show that the spectral response of a Fabry-Perot semiconductor saturable absorber depends on laser beam focusing. We used this effect to achieve stable passive mode-locked operation in a simple and environmentally stable fiber laser by introducing spectral filtering and forcing near-resonant operation. By reducing the free spectral range and increasing the nonlinear response of the Fabry-Perot saturable absorber, we obtained dual-wavelength mode-locked operation.     

大模场面积光子晶体光纤耗散孤子锁模激光器

研制了一种基于掺Yb3+的双包层大模场面积偏振光子晶体光纤的耗散孤子锁模激光器.利用数值模拟分析了光纤激光器中耗散孤子动力学过程,与全正色散锁模激光器相比,脉冲窄化机理更加丰富,半导体可饱和吸收镜(SESAM)的非线性吸收,啁啾脉冲的光谱滤波以及光纤的增益色散同时起作用,这些因素使耗散孤子锁模更加容易实现,并且稳定运行.其中,光谱滤波的耗散过程是稳定锁模机制的主导因素,滤波片能够在频域和时域同时窄化脉冲,并且去除脉冲啁啾,限制脉冲在腔内始终小于1ps.在实验上实现了无色散补偿腔中直接输出脉冲宽度777fs,最高平均功率达到1W,重复频率48·27MHz,对应单脉冲能量20nJ的飞秒激光.     

Passively harmonic mode-locked fiber laser with controllable repetition rate based on a carbon nanotube saturable absorber

We have proposed and demonstrated a passively harmonic mode-locked fiber laser based on a single-walled carbon nanotube saturable absorber (SWCNT-SA) that has a controllable repetition rate. With the pump power fixed, we have experimentally observed harmonically mode-locked optical pulses with repetition rates that can be controlled over the range from the fundamental to the seventh-order mode through careful adjustment of the polarization controller only. From the experimental results, we deduce that the likely origin of the self-stabilization is the result of global and local soliton interactions induced by the continuous wave (CW) components.     

Observation of wavelength-switchable solitons in an all-polarization-maintaining erbium-doped fiber cavity based on graphene saturable absorber reflector

We present the generation of wavelength-switchable single-polarization solitons in an all-polarization-maintaining erbium-doped fiber laser mode-locked by a graphene saturable absorber. Ultrashort pulses centered at the wavelength of 1531.6 nm with the duration of 816 fs and centered at the wavelength of 1557.8 nm with the duration of 402 fs are separately obtained from the same fiber laser cavity. The cavity loss adjusted by the gold reflector plays a crucial role in wavelength switching.     

氧化石墨烯被动锁模掺镱光纤激光器多脉冲现象的实验研究

利用氧化石墨烯作为可饱和吸收体,在被动锁模全正常色散掺镱光纤激光器中研究了多脉冲的现象,在同一抽运功率不同偏振态下,实验获得了矩形脉冲谐波锁模、耗散孤子谐波锁模、准谐波锁模,脉冲峰值周期性调制,脉冲簇、脉冲束、混沌多重脉冲的多脉冲现象,插入激光腔内的2nm窄带滤波器具有限制增益带宽、对脉冲塑形、诱导多脉冲产生的作用,调节偏振控制器相当于改变腔内增益,是实现不同类型多脉冲现象的主要原因,本实验研究有利于加深对多脉冲动力学行为在正常色散区域氧化石墨烯锁模掺镱光纤激光器中的理解。     

Passively mode-locked erbium-doped fiber laser via a D-shape-fiber-based MoS_2 saturable absorber with a very low nonsaturable loss

We report on the generation of conventional and dissipative solitons in erbium-doped fiber lasers by the evanescent field interaction between the propagating light and a multilayer molybdenum disulfide(MoS_2) thin film. The MoS_2 film is fabricated by depositing the MoS_2 water–ethanol mixture on a D-shape-fiber(DF) repetitively. The measured nonsaturable loss, saturable optical intensity, and the modulation depth of this device are 13.3%, 110 MW/cm~2, and 3.4% respectively.Owing to the very low nonsaturable loss, the laser threshold of conventional soliton is as low as 4.8 mW. The further increase of net cavity dispersion to normal regime, stable dissipation soliton pulse trains with a spectral bandwidth of 11.7 nm and pulse duration of 116 ps are successfully generated. Our experiment demonstrates that the MoS_2-DF device can indeed be used as a high performance saturable absorber for further applications in ultrafast photonics.