Synthesis, microstructure and photoluminescence of Eu/Tb activated Y2SiO5 nanophosphors by new silicate sources

Y_2−xTb_xSiO₅ and Y_2−xEu_xSiO₅ nanophosphors with seven different kinds of silicate sources were synthesized by sol-gel method. The structures have been investigated to be composed of nanometer-size grains of 30-60 nm through X-ray diffraction (XRD) and scanning electron microscopy (SEM) was used to compare the different morphology of patterns from seven different silicon sources. The photoluminescence of Y_2−xTb_xSiO₅ was investigated as a function of silicate sources and the results revealed that these nanometer materials showed the characteristic emission ⁵D₄ → ⁷F_J (J = 6, 5, 4, 3) of Tb ions. The characteristic emission ⁵D₀ → ⁷F_J (J = 1, 2, 4) of Eu ions was also found in the materials of Y_2−xEu_xSiO₅.     

Structural and optical properties of thin films porous amorphous silicon carbide formed by Ag-assisted photochemical etching

In this work, we present the formation of porous layers on hydrogenated amorphous SiC (a-SiC: H) by Ag-assisted photochemical etching using HF/K₂S₂O₈ solution under UV illumination at 254 nm wavelength. The amorphous films a-SiC: H were elaborated by d.c. magnetron sputtering using a hot pressed polycrystalline 6H-SiC target. Because of the high resistivity of the SiC layer, around 1.6 MΩ cm and in order to facilitate the chemical etching, a thin metallic film of high purity silver (Ag) has been deposited under vacuum onto the thin a-SiC: H layer. The etched surface was characterized by scanning electron microscopy, secondary ion mass spectroscopy, infrared spectroscopy and photoluminescence. The results show that the morphology of etched a-SiC: H surface evolves with etching time. For an etching time of 20 min the surface presents a hemispherical crater, indicating that the porous SiC layer is perforated. Photoluminescence characterization of etched a-SiC: H samples for 20 min shows a high and an intense blue PL, whereas it has been shown that the PL decreases for higher etching time. Finally, a dissolution mechanism of the silicon carbide in 1HF/1K₂S₂O₈ solution has been proposed.     

Growth and spectral properties of Nd:GdVO4 laser crystal

In this paper, the Czochralski growth, absorption spectra, and photoluminescence spectra of Nd:GdVO₄ crystals are studied. From its absorption spectra, Nd:GdVO₄ is found to exhibit an anisotropic optical absorption effect, and its effective Judd-Ofelt parameters are calculated: Ω₂=10.281×10⁻²⁰ cm², Ω₄=5.426×10⁻²⁰ cm² and Ω₆=9.943×10⁻²⁰ cm². By these parameters, the absorption oscillator strengths, emission oscillator strengths, transition probabilities, fluorescence branch ratios, energy lifetimes, and integrated emission cross-sections are also derived. The photoluminescence spectra of Nd:GdVO₄ crystal consist of a wide emission band of host and the characteristic emission bands of Nd³⁺. Based on the excitation spectrum, both the two evident peaks locating at 345 and 371 nm are ascribed to the characteristic excitation of Nd³⁺, and an energy transfer from the host to its doping Nd³⁺ ions is indicated.     

Fast and efficient VUV/UV emissions from (Ba,La)F2:Er crystals

We report observation of fast and efficient VUV/UV luminescence from the mixed (Ba,La)F₂:Er crystals. The broad bands, peaking at 162.5, 181.9, 194.2, 202.8, 216.1, 233.5 and 281.5 nm and decaying, at 10 and 293 K, with time constants of 46 and 35 ns respectively, are due to spin-allowed transitions from the low-spin (LS) state of the 4f¹⁰5d configuration.We also observed a weak and slow broad band emission peaking at 170 nm due to the spin-forbidden transition from the high-spin (HS) state of the 4f¹⁰5d configuration.While at room temperature the excitation into any of the three identified LS bands (J=8, 7 and 6) dominating the excitation spectrum yields fast VUV and UV emissions, at 10 K the excitation into higher lying J=7 and 6 bands generates slow and sharp line emissions. The positions of these lines fit energies of transitions originating from the ²G_7/2 multiplet at 66140 cm⁻¹. The emission from the ²G_7/2 multiplet has been never, to the best of our knowledge, observed before.The efficient and fast VUV and UV emissions from the higher (LS, J=8) with almost no contribution from the lower (HS, J=8) level of the 4f¹⁰5d configuration are possible because the modified crystal field in (Ba,La)F₂ shifts the level of the (LS, J=8) state below the ²F_5/2 multiplet which, therefore, does not contribute to nonradiative relaxation between the LS and HS levels.We conclude that the ²G_7/2 and ²F_5/2 levels have major impact on VUV and UV emissions from the Er³⁺ ion in (Ba,La)F₂ contributing to complex emission pattern described in this report Their key role, elucidated by the VUV and UV luminescence spectroscopy, is consistent with predictions from a simple configuration coordinate model based on experimental results and calculations of the 4f¹¹ energy levels.     

Photoluminescence scanning on InAs/InGaAs quantum dot structures

The photoluminescence spectra of InAs quantum dots (QDs) embedded into four types of In_xGa_1−xAs/GaAs (x = 0.10, 0.15, 0.20 and 0.25) multi quantum well MBE structures have been investigated at 300 K in dependence on the QD position on the wafer. PL mapping was performed with 325 nm HeCd laser (35 mW) focused down to 200 μm (110 W/cm²) as the excitation source. The structures with x = 0.15 In/Ga composition in the In_xGa_1−xAs capping layer exhibited the maximum photoluminescence intensity. Strong inhomogeneity of the PL intensity is observed by mapping samples with the In/Ga composition of x ≥ 0.20-0.25. The reduction of the PL intensity is accompanied by a gradual “blue” shift of the luminescence maximum at 300 K as follows from the quantum dot PL mapping. The mechanism of this effect has been analyzed. PL peak shifts versus capping layer composition are discussed as well.     

Spectral properties of Nd:Ca2Nb2O7 crystal

This paper reports the spectral properties of Nd³⁺:Ca₂Nb₂O₇. The spectral parameters of Nd³⁺ in Nd³⁺:Ca₂Nb₂O₇ crystal have been investigated based on Judd-Ofelt theory. The spectral parameters were obtained. The parameters of line strengths Ω_λ are Ω₂=4.967×10⁻²⁰ cm², Ω₄=5.431×10⁻²⁰ cm², Ω₆=5.693×10⁻²⁰ cm². The radiative lifetime, the fluorescence lifetime and the quantum efficiency are 122 μs, 103 μs and 84.4%, respectively. The fluorescence branch ratios calculated: β₁=0.425, β₂=0.479, β₃=0.091, β₄=0.004. The emission cross section at 1068 nm is 6.204×10⁻²⁰ cm².     

Simulation and fabrication study of porous silicon photonic crystal

The present work reports design and fabrication of porous silicon based one-dimensional (1D) photonic crystal. Distributed Bragg reflector (DBR) is a 1D photonic crystal composed of multilayer stack of high and low refractive index layers. Design of porous silicon DBR is a complex one and requires appropriate control in optical parameters of its constituent layers. In order to design DBR, two porous silicon single layer samples were fabricated using current density of 10 and 50 mA/cm². Optical characterization of single layer samples showed series of interference fringes. Reflective interferometric Fourier transform spectroscopy (RIFTS) method was employed to determine optical constants of porous silicon single layers. DBR simulation was carried out based on transfer matrix method. DBR was then fabricated using optical parameters obtained from RIFTS method. Reflection bandwidth of prepared DBR was found to be 216 nm, which is comparable to the simulated value of 203 nm.     

Interference of resonance luminescence of exciton polaritons in CuGaS2 crystals

The nonmodulated and wavelength-modulated reflection spectra of CuGaS₂ crystals for the polarization EIIc of 10 K are studied. The states n = 1, 2 and 3 of the excitons Γ₄ (A-excitons) and n = 1, n = 2 of B- and C-excitons are found. The nonmodulated absorption spectra for the polarization E⊥c at 10 K have been studied. The states n = 1, 2 and 3 of Γ₅ excitons are found. The main parameters of the A (Γ₄, Γ₅) and B, C exciton series at the energies of the longitudinal and transverse excitons Γ₄ for the states n = 1 and n = 2, the effective masses of electrons and holes are determined. The photoluminescence peaks were observed at n = 3 and n = 4 of the excitons Γ₅ in the luminescence spectra excited by the line 4880 Å of Ar⁺ laser. In the luminescence spectra the interference is found.     

Nonlinear optical properties of periodic gold nanoparticle arrays

Periodic Au nanoparticle arrays were fabricated on silica substrates using nanosphere lithography. The identical single-layer masks were prepared by self-assembly of polystyrene nanospheres with radius R = 350 nm. The structural characterization of nanosphere masks and periodic particle arrays was investigated by atomic force microscopy. The nonlinear optical properties of the Au nanoparticle arrays were determined using a single beam z-scan method at a wavelength of 532 nm with laser duration of 55 ps. The results show that periodic Au nanoparticle arrays exhibit a fast third-order nonlinear optical response with the nonlinear refractive index and nonlinear absorption coefficient being n₂ = 6.09 × 10⁻⁶ cm²/kW and β = −1.87 × 10⁻⁶ m/W, respectively.     

Si-based two-dimensional photonic crystals coupled to one-dimensional Bragg mirrors

Planar two-dimensional photonic crystals can be combined with a one-dimensional Bragg mirror to control the quality factor and out-of-plane coupling of optical Bloch modes. We have investigated the optical properties of such structures fabricated on silicon. The photonic crystals are fabricated in the upper Si layer deposited on top of quarter-wave thick SiO₂-polycrystalline Si layers. The optical properties are probed by the room-temperature photoluminescence of Ge/Si self-assembled islands as an internal source. We show that an enhancement of the quality factor can be obtained by controlling the thickness of the silicon upper layer in which the two-dimensional photonic crystal is etched and by controlling the air filling factor of the photonic crystal. Quality factors of 2200 around 1100 nm are obtained by this method for defect-free photonic crystals with a square lattice pattern. The experimental results are supported by three-dimensional finite-difference time-domain (FDTD) calculations of the radiated modes for the investigated structures.     

Photoluminescence from C ion-implanted and electrochemical etched Si layers

The microstructural and optical analysis of Si layers emitting blue luminescence at about 431 nm is reported. These structures have been synthesized by C⁺ ion implantation and high-temperature annealing in hydrogen atmosphere and electrochemical etching sequentially. With the increasing etching time, the intensity of the blue peak increases at first, decreases then and is substituted by a new red peak at 716 nm at last, which shows characteristics of the emission of porous silicon. CO compounds are induced during C⁺ implantation and nanometer silicon with embedded structure is formed during annealing, which contributes to the blue emission. The possible mechanism of photoluminescence is presented.     

Effects of seed layer on the structure and property of zinc oxide thin films electrochemically deposited on ITO-coated glass

ZnO films with different morphologies were deposited on the ITO-coated glass substrate from zinc nitrate aqueous solution at 65 °C by a seed-layer assisted electrochemical deposition route. The seed layers were pre-deposited galvanostatically at different current densities (i_sl) ranging from −1.30 to −3.0 mA/cm², and the subsequent ZnO films had been done using the potentiostatic technique at the cathode potential of −1.0 V. Densities of nucleation centers in the seed layers varied with increasing the current density, and the ZnO films on them showed variable morphologies and optical properties. The uniform and compact nanocrystalline ZnO film with (0 0 2) preferential orientation was obtained on seed layer that was deposited under the current density (i_sl) of −1.68 mA/cm², which exhibited good optical performances.     

Spin-transfer switching in MgO magnetic tunnel junction nanostructures

Spin-transfer driven switching was observed in MgO based magnetic tunnelling junctions (MTJ) with tunnelling magnetoresistance ratio of up to 160% and the average intrinsic switching current density (J_c0) down to 2 MA/cm², which are the best known results reported in spin-transfer switched MTJ nanostructures. Based on a comparison of results both from MgO and AlO_x MTJs, further switching current decrease via MgO dual structures with two pinned layers is discussed.     

Fine structure on the excitonic emission in AgI nanoparticles embedded in silica glass

Stable photoluminescence (PL) from AgI nanoparticles embedded in silica glass was investigated at room temperature. The Z_1,2 excitonic emission of AgI exhibits fine structure with spacing of ∼0.20 eV (1610 cm⁻¹), which is assigned to the frequency of vibration in interfacial water species. The PL excitation spectrum displays two newly observed bands at 3.45 and 4.35 eV associated with AgI-silica interaction. We suggest that the excitons in AgI are localized in the AgI/SiO₂ interface region before radiative recombination.     

Photoluminescence spectra of nitrogen implanted GaSe crystals

GaSe single crystals were N-implanted along c-axis with ion beams of 10¹⁴ and 10¹⁶ ions/cm² doses having energy values of 60 and 100 keV. The photoluminescence (PL) spectra of undoped and N-implanted GaSe crystals were measured at different temperatures. The PL intensity was observed to decrease with increasing implantation dose while the FWHM of the exciton peaks increased. In heavily doped crystals, due to the interaction with the radiation induced disorders, the wave vector selection rules are satisfied and an indirect exciton PL band is observed 36 meV below the direct exciton states.     

Investigation of porous silicon carbide as a new material for environmental and optoelectronic applications

In this paper, we present an experimental study on the chemical and electrochemical etching of silicon carbide (SiC) in different HF-based solutions and its application in different fields, such as optoelectronics (photodiode) and environment (gas sensors). The thin SiC films have been grown by pulsed laser deposition method. Different oxidant reagents have been explored. It has been shown that the morphology of the surface evolves with the etching conditions (oxidant, concentration, temperature, etc.). A new chemical polishing solution of polycrystalline 6H-SiC based on HF:Na₂O₂ solution has been developed. Moreover, an electrochemical etching method has been carried out to form a porous SiC layer on both polycrystalline and thin SiC films. The PL results show that the porous polycrystalline 6H-SiC and porous thin SiC films exhibited an intense blue luminescence and a green-blue luminescence centred at 2.82 eV (430 nm) and 2.20 eV (560 nm), respectively. Different device structures based on both prepared samples have been investigated as photodiode and gas sensors.     

Room-temperature electrosynthesized ZnO thin film with strong (0 0 2) orientation and its optical properties

ZnO thin film with strong orientation (0 0 2) and smooth surface morphology was electrosynthesized on ITO-coated glass substrate at room temperature under pulsed voltage. Photoluminescence (PL) shows two obvious peaks: violet band and strong green band. The former is due to the free-excitonic transition and the latter is believed to arise from the single ionized oxygen vacancy (V_O⁺). Raman scattering reveals that the 580 cm⁻¹ mode and the shoulder peak mode at 550 cm⁻¹ originate from the N-related local vibration mode (LVM) and E₁ (LO) mode, respectively.     

Spectroscopic investigations of Nd-, Er-, Er/Yb-, and Tm-ions doped SiO2-Al2O3-CaF2-GdF3 glasses

This paper reports on the absorption, visible and near-infrared luminescence properties of Nd³⁺, Er³⁺, Er³⁺/2Yb³⁺, and Tm³⁺ doped oxyfluoride aluminosilicate glasses. From the measured absorption spectra, Judd-Ofelt (J-O) intensity parameters (Ω₂, Ω₄ and Ω₆) have been calculated for all the studied ions. Decay lifetime curves were measured for the visible emissions of Er³⁺ (558 nm, green), and Tm³⁺ (650 and 795 nm), respectively. The near infrared emission spectrum of Nd³⁺ doped glass has shown full width at half maximum (FWHM) around 45 nm (for the ⁴F_3/2→⁴I_9/2 transition), 45 nm (for the ⁴F_3/2→⁴I_11/2 transition), and 60 nm (for the ⁴F_3/2→⁴I_13/2 transition), respectively, with 800 nm laser diode (LD) excitation. For Er³⁺, and Er³⁺/2Yb³⁺ co-doped glasses, the characteristic near infrared emission bands were spectrally centered at 1532 and 1544 nm, respectively, with 980 nm laser diode excitation, exhibiting full width at half maximum around 50 and 90 nm for the erbium ⁴I_13/2→⁴I_15/2 transition. The measured maximum decay times of ⁴I_13/2→⁴I_15/2 transition (at wavelength 1532 and 1544 nm) are about 5.280 and 5.719 ms for 1Er³⁺ and 1Er³⁺/2Yb³⁺ (mol%) co-doped glasses, respectively. The maximum stimulated emission cross sections for ⁴I_13/2→⁴I_15/2 transition of Er³⁺ and Er³⁺/Yb³⁺ are 10.81×10⁻²¹ and 5.723×10^-21 cm². These glasses with better thermal stability, bright visible emissions and broad near-infrared emissions should have potential applications in broadly tunable laser sources, interesting optical luminescent materials and broadband optical amplification at low-loss telecommunication windows.     

Investigation of spectroscopic properties and thermal stability of Er/Yb-co-doped Bi2O3-B2O3-Ga2O3 glasses

A series of Er³⁺/Yb³⁺-co-doped 60Bi₂O₃-(40−x) B₂O₃ -xGa₂O₃ (BBGA x=0, 4, 8, 12, 16 mol%) glasses have been prepared. The absorption spectra, emission spectra, fluorescence lifetime of Er³⁺:⁴I_13/2 level and thermal stability were measured and investigated. Three Judd-Ofelt intensity parameters Ω_t (t=2,4,6) (Ω₂=(4.67-5.93)×10⁻²⁰ cm², Ω₄=(1.50-1.81)×10⁻²⁰ cm², Ω₆=(0.92-1.17)×10⁻²⁰ cm²) of Er³⁺ ions were calculated by Judd-Ofelt theory. It is found that the Ω₆ first increases with the increase of Ga₂O₃ content from 0 to 8 mol% and then decreases, which is mainly affected by the number of non-bridging oxygen ions of the glass network. The high peak of stimulated emission cross-section () of Er³⁺: ⁴I_13/2→⁴I_15/2 transition were obtained according to McCumber theory and broad full width at half maximum (FWHM=69-76 nm) of the ⁴I_13/2→⁴I_15/2 transition of Er³⁺ ions were measured. The results indicate that these new BBGA glasses can be used as a candidate host material for potential broadband optical amplifiers.     

Enhanced ferroelectric property of (Pb0.95Ca0.05)(Nb0.02Zr0.80Ti0.20)O3 thin films prepared by RF magnetron sputtering

(Pb_0.95Ca_0.05)(Nb_0.02Zr_0.80Ti_0.20)O₃ [PCNZT] thin films were deposited on the Pt(1 1 1)/Ti/SiO₂/Si(1 0 0) substrates by RF magnetron sputtering with and without a LaNiO₃ [LNO] buffer layer. Ca and Nb elements in PZT films enhance the ferroelectric property, LaNiO₃ buffer layer improves the crystal quality of the PCNZT thin films. PCNZT thin films possess better ferroelectric property than that of PZT films for Ca and Nb ion substitution, moreover, PCNZT thin films with a LNO buffer layer possess (1 0 0) orientation and good ferroelectric properties with high remnant polarization (P_r = 38.1 μC/cm²), and low coercive field (E_c = 65 kV/cm), which is also better than that of PCNZT thin films without a LNO buffer layer (P_r = 27.9 μC/cm², E_c = 74 kV/cm). The result shows that enhanced ferroelectric property of PZT films can be obtained by ion substitution and buffer layer.