The preparation of optical fibre nanoprobe and its application in spectral detection

As an important component of scanning near-field optical microscope (SNOM), optical fibre nanoprobe has been applied to many fields extensively. A melt-stretched etching method is proposed to produce optical fibre nanoprobe with low cost. Firstly, optical fibre tip with micrometer-sized diameter is created by the melt-stretched measure. Next, it is dipped into hydrofluoric acid (HF), and a fine optical fibre nanoprobe will be made after a short-time etching. Owing to the taper structure of tip, it can be etched again in acid if a nanoprobe is not constructed when the first etching is completed. In addition, optical fibre nanoprobe is applied to spectral investigation, and the fluorescence spectroscopy of rhodamine B (Rh B) solution is collected by an optical investigation system with a bifurcated fibre.     

Influence of cross-phase modulation and four-photon parametric mixing on the relative motion of optical pulses

Two mechanisms of self-confinement of wave packets on different frequencies in a monomode optical fibre are investigated. It is shown that the equations describing the processes possess a Hamiltonian structure. A new class of asymptotically free soliton solution is found. Two spectral bandwidths for self-confinement of the optical pulses are determined.     

Influence of cross phase modulation and four-photon parametric mixing on the relative motion of optical pulses

Two mechanisms of self-confinement of wave packets on different carrying frequencies in monomode optical fibre are investigated. It is shown that the equations describing the processes possess a Hamiltonian structure. A new class of asymptotically free soliton solutions are found. Two spectral bandwidths for self-confinement of the optical pulses are determined.     

耦合结构有机微腔的光致发光特性

耦合光学微腔(Coupled optical microcavity,CMC)是一种特殊结构的微腔,在耦合微腔中,两个独立的微腔相邻耦合在一起.通常一个腔是无源的,另一个腔是有源的.首次研究了有机材料在耦合微腔中的自发发射特性.实验采用的有机发光材料为八羟基喹啉铝Tris(8-quinolinolato)aluminium(Alq₃),器件的结构为Glass/DBR_A/Filler/DBR_B/Alq₃/DBR_C.底部腔是无源的,组成为DBR_A/Filler/DBR_B.顶部腔是有源的,由DBR_B/Alq₃/DBR_C构成.其中反射镜DBR_A、DBR_B、DBR_C以及填充层(Filler)均由光学介质材料构成.通过结构设计使两个腔的谐振波长均位于530nm.耦合微腔器件与单层Alq₃薄膜相比较,Alq₃薄膜的光致发光光谱是峰值位于511nm的宽谱带,而在耦合微腔器件中观察到的是具有两个腔模式,峰值波长分别位于518,553nm的增强并窄化的光谱.这是由于两个腔的光场耦合引起了腔模式分裂.结果表明耦合微腔能极大地改变有机材料的自发发射特性,可以用来提高器件的发光效率.     

Design of dual-core resonant leaky optical fibre based gain flattening filters for erbium doped fibre amplifiers

We propose optical fibre based filters employing dual-core resonant leaky structure for gain equalization of erbium doped fibre amplifier (EDFA). Spectral loss variation of the structure has been utilized to suppress gain peak and, thus, flatten overall gain profile in the C-band. We show 15.7 dB flat gain with ± 1.6 dB ripple in the wavelength range from 1525 nm to 1555 nm using a single filter and 18±0.7 dB gain using two cascaded filters.     

Non-stoichiometric metals with strongly varying electron concentration: Gd-monochalcogenides and LaS

The reflectivity of single crystals of Gd monochalcogenides and of LaS has been measured at 300 K in the spectral region between 0.03 and 12eV. Special attention has been given to the chemical analysis of the materials and the determination of the deviation from stoichiometry. The optical constants have been determined by means of a Kramers-Kronig relation. A coupled mode of plasmons with interband transitions has been observed. The separation into interband transitions and free electron behaviour permitted the determination of the number of free carriers and their effective mass. It can be shown that the carrier concentration changes much more drastically than the stoichiometry. By comparison with LaS the position of the 4f⁷ levels of GdS was found to be 9 eV below the Fermi level.     

Uniform oscillations of supercontinua

Uniform oscillations of supercontinua, generated with microstructured fibre, have been observed and investigated. The oscillations are uniform in the sense that the optical power through the fibre changes with a regular and periodic waveform and the spectral bandwidth of the transmitted light changes correspondingly. The oscillations are continuous over periods of hours and the spectral width ranges from the octave-spanning condition (～310-THz wide at 20 dB below the maximum) to zero broadening of the input light. The corresponding contrast ratio of the fluctuating output light signal is as high as 0.75. Silica photonic crystal fibre with hexagonal air-hole structure and core diameter of 2.0 μm was used for the supercontinuum generation. The oscillations are produced when at least 15 mm of fibre is allowed to extend from the mount of the fibre launcher. Arguments in terms of thermal behaviour are used in an attempt to explain the fluctuations of light through the microstructured fibre. This appears to be the first occasion in which such behaviour has been reported.     

Evolution of optical solitons in nonlinear dispersive lossy fibres

A variational technique has been applied to the evolution of optical solitons in a nonlinear dispersive lossy fibre. An analytical model has been developed to describe the interaction of two co-propagating orthogonally polarized optical pulses in a lossy fibre, governed by a pair of coupled nonlinear Schroedinger equations, and the threshold amplitude at which the solitons form a bound state has been obtained.     

Characteristics of Er and Er-Yb-Cr doped phosphate microsphere fibre lasers

In this paper both Er and Er-Yb-Cr doped phosphate microspheres have been successfully created through precise melting of the ends of fibre tapers, drawn, respectively, from Er and Er-Yb-Cr doped phosphate glasses. When coupled with a fibre taper, a microsphere fibre laser cavity can thus be configured creating a system pumped by a 980 nm laser diode and using an optical spectrum analyzer to monitor the spectral characteristics of the laser output. The performance and characteristics of the Er and Er-Yb-Cr microsphere lasers thus created are discussed in detail and cross-compared in this paper. Both lasers have shown low-threshold in terms of the pump power and the laser output wavelengths and a close investigation of the system has shown that the output power and laser stability are closely related to the size of the microsphere, the pump power and the microsphere material composition.     

An all-fibre multi-parameter sensor for composite structures based on a chirped fibre Bragg grating

An all-fibre multi-parameter sensor for composite structures based on a chirped optical fibre Bragg grating (CFBG) has been studied theoretically and experimentally. The principle of multi-parameters sensing with a single CFBG is based on that the centre wavelength and the FWHM (full width at half maximum) in the reflection spectrum of a CFBG vary linearly with the temperature and/or the axial stress. A wavelength matched optical fibre long period grating (LPG) and another wavelength matched reference CFBG (CFBGR) have been used to interrogate the signal of the sensor CFBG (CFBGS). The temperature and strain of the composite structure have been monitored real-time with one CFBG as a single sensor head. The temperature resolution of 0.12°C and the strain resolution of 1.1μ? for a composite structure have been realized in experiments. The experiment results agree well with the theoretical analyses.     

半导体光纤温度传感器

本文利用半导体材料的吸收光谱随温度变化的特性,研制了数字显示光纤测温仪。经过反复试验,该仪器在-20°～200℃温度范围内的测温精度为±2℃。     

Full-range tunable optical delay line based on coupled and side-coupled resonators

An optical delay line based on a new kind of structure comprising coupled resonators and side-coupled resonators has been proposed and demonstrated. The structure has unique advantages in realizing tunable optical delay lines. The tuning range has covered almost the full range of the optical delay line, from minimum delay at which only one ring of the light pulse structure requires transmission, to maximum delay at which all rings are required. In addition, the input signal delivered from the input to output port travels the structure twice, thereby providing buffer delay that is twice longer than general coupled resonators.     

Polymer optical fibre Bragg gratings based fibre laser

For the first time the fibre laser constructed from a polymer optical fibre Bragg grating is reported. The single frequency laser with the peak power of −5 dBm and signal to noise ratio greater than 45 dB has been achieved. Further examination demonstrates the excellent characteristics of the fibre laser. First, the fibre laser can be easily tuned over 35 nm by the simple axial tension method. Second, the fibre laser has the high strain sensitivity of 1.48 pm/με with the dynamic measurement range as large as 2.37%.     

Preparation and electronic structure of phase pure K3C60

Phase pure K₃C₆₀ films have been grown using vacuum distillation. The structure of such films could be shown to be face centered cubic consistent with X-ray diffraction studies. The electronic structure of the films has been studied using electron energy-loss spectroscopy in transmission. From C1s core excitation measurements the unoccupied density of states has been determined. Performing the dielectric function has been derived in a wide energy range (0–45 eV). It is shown that the low energy part of the optical conductivity cannot be understood within a simple free electron model but that interband transitions between the three conduction bands have to be taken into account. The spectral weight of interband transitions between valence and conduction bands shows strong momentum dependence due to optical selection rules demonstrating the molecular-like nature of the electronic states.     

Spectral-domain intermodal interference under general measurement conditions

Spectral-domain intermodal interference is analysed theoretically at the output of a few-mode optical fibre alone and at the output of the optical fibre in a tandem configuration with a Michelson interferometer. The theoretical analysis is performed under general measurement conditions when a light source of a given spectral bandwidth and a spectrometer of a given spectral bandpass are considered and when first- and second-order intermodal dispersion effects in the optical fibre are taken into account. Thus, the effect of a variable spectral bandpass of a low-resolution spectrometer on the spectral fringe visibility functions for a two-mode optical fibre of known intermodal dispersion is specified.     

Transmission properties of microcoils based on twisted birefringent fibre

We model the linear transmission properties of birefringent optical microcoil resonators (OMRs) by numerically solving polarisation dependent coupled mode equations. When the fibre is twisted, results show spectral bands where strong coupling between the different polarisations occur. The extinction ratio of certain resonances is also found to be enhanced by the exchange of power into another polarisation. Compared to the standard OMR, the choice of fibre twist and level of birefringence provide additional flexibility in tailoring the OMR spectral properties as needed for applications such as filtering, signal processing and sensing.     

一种新型高灵敏度光学微环湿度传感器

提出了以聚酰亚胺（PI）为感湿材料的三耦合点单微环新型湿度传感器。外界湿度变化使得聚酰亚胺SOI微环谐振特性发生变化,最终通过谐振波长的漂移量确定湿度值。讨论了不同部位感湿时系统的传感特性,并且选择了最佳湿敏元件。数值模拟结果表明：与传统的单微环传感器相比,新型传感器具有较高灵敏度和测量范围,Through端口的自由频谱范围可提高3倍。三耦合点单微环谐振器整体结构可作为最佳湿敏元件,该传感器在10%RH~80%RH相对湿度范围内,灵敏度可达到0.98 nm/%RH,该结构为制备高灵敏度可集成微型湿度传感器件提供了一定的理论依据。     

Optical properties and electronic structure of europium chalcogenides

The normal incidence reflectivity of europium chalcogenide single crystals and of Gd doped EuO has been measured at room temperature in the spectral region from 250 μm to 12 eV and has been analyzed in terms of the optical constants. In addition, in a reduced spectral region from 0.5 to 6 eV, the optical constants have been evaluated by means of a polarimetric method, as well above as below the magnetic ordering temperature. To enhance the resolution of the magneto-optical transitions, a modulation technique has been applied with a magnetic field as modulating parameter. The Kramers-Kronig relation has been used to analyze the normal incidence reflectivity and the magnetoreflectance spectra in terms of, respectively, the optical constants and the changes in the real and imaginary part of the dielectric response function. For Gd doped EuO the Kramers-Kronig analysis has revealed plasmon and coupled plasmon-phonon modes. The interband transitions of the europium chalcogenides are discussed within the framework of recent APW and OPW energy band calculations. On the other hand we have derived an energy level scheme of the europium chalcogenides from our optical data.     

自由光谱范围加倍的单微环谐振滤波器

基于两点耦合和光波干涉控制相移思想提出U型波导耦合单微环的谐振滤波器结构。利用传输矩阵法推导了此结构的数学模型,采用Matlab模拟了输出端口谱线形状。当微环与U型波导的两个耦合点之间的距离为微环周长的整数倍时,此新型微环谐振滤波器比传统的双直波导耦合单微环滤波器的自由光谱范围增加1倍。针对该结构参数,同时讨论了耦合系数对输出谱线的影响,得出当耦合系数为0.018时,输出谱线具有最佳的消光比,同时保持窄的带宽和高的品质因子。     

Low-temperature dynamics of amorphous polymers and evolution over time of spectra of single impurity molecules: I. Experiment

The optical dynamics of a doped amorphous system, tetra-tert-butylterrylene in amorphous polyisobutylene, has been experimentally studied by the spectra of single impurity molecules measured at temperatures of 2, 4.5, 7, and 15 K. The study of the temporal evolution of the fluorescence excitation spectra of the molecules under consideration made it possible to unambiguously establish the individual identity of the spectra of particular molecules and to analyze their multiplet structure. Repeated scanning of a selected spectral range with subsequent summation of the data made it possible to considerably reduce the errors that arise upon single scanning of the spectra of single molecules. The majority of the spectral trails detected were in agreement with the model of two-level systems. Jumps of spectral lines due to transitions in such systems were observed at all temperatures.