Separation of phenolic acids from sugarcane rind by online solid‐phase extraction with high‐speed counter‐current chromatography

Sugarcane rind contains some functional phenolic acids. The separation of these compounds from sugarcane rind is able to realize the integrated utilization of the crop and reduce environment pollution. In this paper, a novel protocol based on interfacing online solid‐phase extraction with high‐speed counter‐current chromatography (HSCCC) was established, aiming at improving and simplifying the process of phenolic acids separation from sugarcane rind. The conditions of online solid‐phase extraction with HSCCC involving solvent system, flow rate of mobile phase as well as saturated extent of absorption of solid‐phase extraction were optimized to improve extraction efficiency and reduce separation time. The separation of phenolic acids was performed with a two‐phase solvent system composed of butanol/acetic acid/water at a volume ratio of 4:1:5, and the developed online solid‐phase extraction with HSCCC method was validated and successfully applied for sugarcane rind, and three phenolic acids including 6.73 mg of gallic acid, 10.85 mg of p‐coumaric acid, and 2.78 mg of ferulic acid with purities of 60.2, 95.4, and 84%, respectively, were obtained from 150 mg sugarcane rind crude extracts. In addition, the three different elution methods of phenolic acids purification including HSCCC, elution–extrusion counter‐current chromatography and back‐extrusion counter‐current chromatography were compared.     

Determination of Tetracyclines in Honey Using Liquid Chromatography with Ultraviolet Absorbance Detection and Residue Confirmation by Mass Spectrometry

A determination method has been optimized and validated for the simultaneous analysis of tetracycline （TC）, oxytetracycline （OTC）, chlortetracycline （CTC） and doxycycline （DC） in honey. Tetracyclines （TCs） were removed from honey samples by chelation with metal ions bound to small Chelating Sepharose Fast Flow columns and eluted with Na2EDTA-Mcllvaine pH 4.0 buffers. Extracts were further cleaned up by Oasis HLB solid-phase extraction （SPE）, while other solid-phase extraction cartridges were compared. Chromatographic separation was achieved using a polar end-capped C 18 column with an isocratic mobile phase consisting of oxalic acid, acetonitrile and methanol. LC with ultraviolet absorbance at 355 nm resulted in the quantitation of all four tetracycline residues from honey samples fortified at 15, 50, and 100 ng/g, with liner ranges for tetracyclines of 0.05 to 2 μg/mL. Mean recoveries for tetracyclines were greater than 50% with R.S.D. values less than 10% （n= 18）. Detection limits of 5, 5, 10, 10 ng/g for oxytetracycline, tetracycline, chlortetracycline and doxycycline, respectively and quantitation limits of 15 ng/g for all the four tetracyclines were determined. Direct confirmation of the four residues in honey （2-50 ng/g） was realized by liquid chromatography-tandem mass spectrometry （LC/MS/MS）. The linear ranges of tetracyclines determined by LC/MS/MS were between 5 to 300 ng/mL, with the linear correlation coefficient r〉 0.995. The limits of detection of 1 to 2 ng/g were obtained for the analysis of the TCs in honey.     

β‐Cyclodextrin polymer@Fe3O4 based magnetic solid‐phase extraction coupled with HPLC for the determination of benzoylurea insecticides from honey,tomato, and environmental water samples

In this work, a magnetic β‐cyclodextrin polymer was successfully prepared and used as an adsorbent for the magnetic solid‐phase extraction of six benzoylurea insecticides (diflubenzuron, triflumuron, hexaflumuron, teflubenzuron, flufenoxuron, and chlorfluazuron) from honey, tomato, and environmental water samples. The influence of the main experimental conditions on the extraction was studied. Under the optimized conditions, the β‐cyclodextrin polymer@Fe₃O₄ showed an excellent extraction performance for the benzoylurea insecticides. A good linearity was obtained for the analytes in the range of 3.0–800 ng/g for honey samples, 0.3–160 ng/g for tomato samples, and 0.1–80.0 ng/mL for water samples, with the correlation coefficients above 0.9998. Satisfactory repeatabilities were achieved, with the relative standard deviations less than 5.7%. The limits of detection (S/N = 3) of the method for the benzoylurea insecticides were 0.2–0.8 ng/g for honey samples, 0.04–0.10 ng/g for tomato samples, and 0.02–0.05 ng /mL for water samples. The method was successfully used for the determination of the six benzoylurea insecticides residues in honey, tomato, and environmental water samples with a satisfactory result.     

Ionic‐liquid‐based dispersive liquid–liquid microextraction combined with magnetic solid‐phase extraction for the determination of aflatoxins B1, B2, G1, and G2 in animal feeds by high‐performance liquid chromatography with fluorescence detection

A novel two‐step extraction technique combining ionic‐liquid‐based dispersive liquid–liquid microextraction with magnetic solid‐phase extraction was developed for the preconcentration and separation of aflatoxins in animal feedstuffs before high‐performance liquid chromatography coupled with fluorescence detection. In this work, ionic liquid 1‐octyl‐3‐methylimidazolium hexafluorophosphate was used as the extractant in dispersive liquid–liquid microextraction, and hydrophobic pelargonic acid modified Fe₃O₄ magnetic nanoparticles as an efficient adsorbent were applied to retrieve the aflatoxins‐containing ionic liquid. Notably, the target of magnetic nanoparticles was the ionic liquid rather than the aflatoxins. Because of the rapid mass transfer associated with the dispersive liquid–liquid microextraction and magnetic solid phase steps, fast extraction could be achieved. The main parameters affecting the extraction recoveries of aflatoxins were investigated and optimized. Under the optimum conditions, vortexing at 2500 rpm for 1 min in the dispersive liquid–liquid microextraction and magnetic solid‐phase extraction and then desorption by sonication for 2 min with acetonitrile as eluent. The recoveries were 90.3–103.7% with relative standard deviations of 3.2–6.4%. Good linearity was observed with correlation coefficients ranged from 0.9986 to 0.9995. The detection limits were 0.632, 0.087, 0.422 and 0.146 ng/mL for aflatoxins B₁, B2, G1, and G2, respectively. The results were also compared with the pretreatment method carried out by conventional immunoaffinity columns.     

Acrylamide‐functionalized graphene micro‐solid‐phase extraction coupled to high‐performance liquid chromatography for the online analysis of trace monoamine acidic metabolites in biological samples

Monoamine acidic metabolites in biological samples are essential biomarkers for the diagnosis of neurological disorders. In this work, acrylamide‐functionalized graphene adsorbent was successfully synthesized by a chemical functionalization method and was packed in a homemade polyether ether ketone micro column as a micro‐solid‐phase extraction unit. This micro‐solid‐phase extraction unit was directly coupled to high‐performance liquid chromatography to form an online system for the separation and analysis of three monoamine acidic metabolites including homovanillic acid, 5‐hydroxyindole‐3‐acetic acid, and 3,4‐dihydroxyphenylacetic acid in human urine and plasma. The online system showed high stability, permeability, and adsorption capacity toward target metabolites. The saturated extraction amount of this online system was 213.1, 107.0, and 153.4 ng for homovanillic acid, 5‐hydroxyindole‐3‐acetic acid, and 3,4‐dihydroxyphenylacetic acid, respectively. Excellent detection limits were achieved in the range of 0.08–0.25 μg/L with good linearity and reproducibility. It was interesting that three targets in urine and plasma could be actually quantified to be 0.94–3.93 μg/L in plasma and 7.15–19.38 μg/L in urine. Good recoveries were achieved as 84.8–101.4% for urine and 77.8–95.1% for plasma with the intra‐ and interday relative standard deviations less than 9.3 and 10.3%, respectively. This method shows great potential for online analysis of trace monoamine acidic metabolites in biological samples.     

Application of magnetized MOF‐74 to phthalate esters extraction from Chinese liquor

In this study, magnetized MOF‐74 (Ni) was prepared using an ultrasound‐assisted synthesis method. This novel functional magnetic adsorbent was characterized using various techniques. Using the prepared material as adsorbents, a magnetic solid‐phase extraction method coupled with high‐performance liquid chromatography was proposed for determining four phthalate esters in Chinese liquor samples. The extraction parameters, including solution pH, adsorbent amount, extraction time, and eluent type and volume, were optimized. Under the optimized conditions, proposed method showed good linearity within the range of 1.53–200 μg/L for diphenyl phthalate, 2.03–200 μg/L for butyl benzyl phthalate, 7.02–200 μg/L for diamyl phthalate, and 6.03–200 μg/L for dicyclohexyl phthalate, with correlation coefficients > 0.9944, low limits of detection (0.46–2.10 μg/L, S/N = 3), and good extraction repeatability (relative standard deviations of 3.7%, n = 6). This method was successfully used to analyze phthalate esters in Chinese liquor samples with recoveries of 74.4–104.8%. Two phthalate esters were detected in two samples, both at concentrations that satisfied the Chinese national standard, indicating this method has practical application prospects. The extraction efficiency of this method was also compared with conventional solid‐phase extraction using commercial C₁₈ cartridges. The results demonstrated that the proposed magnetic solid‐phase extraction is a simple, time‐saving, efficient, and low‐cost method.     

Microwave‐assisted preparation of magnetic nanoparticles modified with graphene oxide for the extraction and analysis of phenolic compounds

Here in, magnetic nanoparticles combined with graphene oxide adsorbent were fabricated via a microwave‐assisted synthesis method, and used in the solid‐phase extraction of three phenolic compounds (phenol, 4‐nitrophenol, and m‐methylphenol) in environmental water samples. Various instrumental methods were employed to characterize the magnetic nanoparticles modified with graphene oxide. The influence of experimental parameters, such as desorption conditions, amount of adsorbent, extraction time, and pH, on the extraction efficiency was investigated. Owing to the high surface area and excellent adsorption capacity of the prepared material, satisfactory extraction was achieved. Under optimum conditions, a linear response was observed in the concentration range of 1.000–100.0 μg/L for phenol, 0.996–99.6 μg/L for 4‐nitrophenol, and 0.975–97.5 μg/L for m‐methylphenol, with correlation coefficients in the range of 0.9995–0.9997. The limit of detection (signal‐to‐noise ratio of 3) of the method varied between 0.5 and 0.8 μg/L. The relative standard deviations were <5.2%. The recovery percentages of the method were in the range of 89.1–104.3%. The results indicate that the graphene oxide‐modified magnetic nanoparticles possess high adsorptive abilities toward phenolic compounds in environmental water samples.     

Effervescence‐assisted dispersive solid‐phase extraction using ionic‐liquid‐modified magnetic β‐cyclodextrin/attapulgite coupled with high‐performance liquid chromatography for fungicide detection in honey and juice

In this study, a simple effervescence‐assisted dispersive solid‐phase extraction method was developed to detect fungicides in honey and juice. Most significantly, an innovative ionic‐liquid‐modified magnetic β‐cyclodextrin/attapulgite sorbent was used because its large specific surface area enhanced the extraction capacity and also led to facile separation. A one‐factor‐at‐a‐time approach and orthogonal design were employed to optimize the experimental parameters. Under the optimized conditions, the entire extraction procedure was completed within 3 min. In addition, the calibration curves exhibited good linearity, and high enrichment factors were achieved for pure water and honey samples. For the honey samples, the extraction efficiencies for the target fungicides ranged from 77.0 to 94.3% with relative standard deviations of 2.3–5.44%. The detection and quantitation limits were in the ranges of 0.07–0.38 and 0.23–1.27 μg/L, respectively. Finally, the developed technique was successfully applied to real samples, and satisfactory results were achieved. This analytical technique is cost‐effective, environmentally friendly, and time‐saving.     

Simultaneous screening and quantification of aminoglycoside antibiotics in honey using mixed‐mode liquid chromatography with quadrupole time‐of‐flight mass spectroscopy with heated electrospray ionization

An analytical method based on liquid chromatography with quadrupole time‐of‐flight mass spectrometry has been developed for the simultaneous determination of six aminoglycoside antibiotics in honey. The sample pretreatment included extraction with aqueous trichloroacetic acid followed by solid‐phase extraction on Strata‐X polymeric reversed phase cartridges. Liquid chromatography separation was performed on an Obelisc R zwitterionic type mixed‐mode column. An ionBooster™ heated electrospray source was used and showed enhanced ionization efficiency in comparison to a conventional electrospray source. The observed signal enhancement ranged from 3‐ (neomycin) to 16‐fold (gentamicin C1). A data‐dependent mass spectrometry acquisition approach was employed, in which the full mass spectrometry dataset provided quantification and a scheduled precursor list was used to trigger an alternating data‐dependent acquisition of MS² spectra for confirmation purposes. The described method was validated in accordance to CD 2002/657/EC. Decision limit values were in the range 11.2–33.6 ng/g, and satisfactory performance characteristics were obtained for recovery (65–76%), repeatability (3.8–7.3%), and linearity (≥0.995). The method was applied to the analysis of 49 real honey samples from the country of Georgia. Streptomycin was detected in two samples at 117 and 35 ng/g, and gentamicin C1 was detected in one sample at 32 ng/g.     

Multi‐walled carbon nanotube modified dummy‐template magnetic molecularly imprinted microspheres as solid‐phase extraction material for the determination of polychlorinated biphenyls in fish

Novel multi‐walled carbon nanotube modified dummy‐template molecularly imprinted microspheres (MWCNTs@DMMIPs) were successfully synthesized as adsorbents for six kinds of polychlorinated biphenyls (PCBs). MWCNTs@DMMIPs were prepared by a surface molecular imprinting technique. Core–shell Fe₃O₄@SiO₂ nanoparticles were employed as magnetic support. 3,4‐Dichlorobenzene acetic acid was used as a dummy template instead of PCBs, methacrylic acid was used as functional monomer and ethylene glycol dimethacrylate was used as the cross‐linker. The resulting absorbent was characterized by various methods. The adsorbent was employed for extracting PCBs and exhibited good selectivity and high adsorption efficiency. Furthermore, it was reusable and capable of magnetic separation. Adsorption kinetics fit well with a pseudo‐second‐order kinetic equation and also exhibited a three‐stage intra‐particle diffusion model. The Freundlich model was used to describe the adsorption isotherms. The materials were successfully applied to the magnetic dispersive solid‐phase extraction of six kinds of PCBs followed by gas chromatography with mass spectrometry determination in fish samples, the limit of detection of six kinds of PCBs were 0.0028–0.0068 μg/L and spiked recoveries ranged between 73.41 and 114.21%. The prepared adsorbent was expected to be a new material for the removal and recovery of PCBs from contaminated foods.     

Loading controlled magnetic carbon dots for microwave‐assisted solid‐phase extraction: Preparation,extraction evaluation and applications in environmental aqueous samples

An adsorbent of carbon dot@poly(glycidyl methacrylate)@Fe₃O₄ nanoparticles has been developed for the microwave‐assisted magnetic solid‐phase extraction of polycyclic aromatic hydrocarbons in environmental aqueous samples prior to high‐performance liquid chromatography with UV/visible spectroscopy detection. Poly(glycidyl methacrylate) was synthesized by atom transfer radical polymerization. The chain length and amount of carbon dots attached on them can be easily controlled through changing polymerization conditions, which contributes to tunable extraction performance. The successful fabrication of the nano‐adsorbent was confirmed by transmission electronic microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and vibrating sample magnetometry. The extraction performance of the adsorbent was evaluated by using polycyclic aromatic hydrocarbons as model analytes. The key factors influencing the extraction, such as microwave power, adsorption time, desorption time and desorption solvents were investigated in detail. Under the optimal conditions, the microwave‐assisted method afforded magnetic solid‐phase extraction with short extraction time, wide dynamic linear range (0.02–200 μg/L), good linearity (R² ≥ 98.57%) and low detection limits (20–90 ng/L) for model analytes. The adsorbent was successfully applied for analyzing polycyclic aromatic hydrocarbons in environmental aqueous samples and the recoveries were in the range of 86.0–124.2%. Thus, the proposed method is a promising candidate for fast and reliable preconcentration of trace polycyclic aromatic hydrocarbons in real water samples.     

Analysis of microcystins using high‐performance liquid chromatography and magnetic solid‐phase extraction with silica‐coated magnetite with cetylpyridinium chloride

Microcystins (MCs), produced by freshwater cyanobacteria, can be serious water pollutants, so it is important to monitor their concentration in drinking water. We have developed a method for rapid and accurate determination of microcystin levels in environmental water, using magnetic solid‐phase extraction and high‐performance liquid chromatography with UV detection. The magnetic composite material, which was combined with cetylpyridinium chloride, was prepared by hydrothermal synthesis. The optimal extraction of microcystins in water sample was achieved by optimizing the amount of adsorbent, time of adsorption, ratio of eluting solvent, and volume of eluent. Under the optimal conditions, the limit of detection of MC‐LR was 0.001 μg/L, and the limit of quantification was 0.0028 μg/L. The limit of detection of MC‐RR was 0.001 μg/L, and the limit of quantification was 0.003 μg/L. These values are far lower than those established by the International Health Organization for the maximum concentration of microcystins in drinking water. The magnetic solid‐phase extraction adsorbent used in this method has the advantages of simple preparation, low price, and easy solid–liquid separation, and it can be used for the rapid and sensitive monitoring of trace microcystins in environmental water samples.     

3‐D graphene‐supported mesoporous SiO2@Fe3O4 composites for the analysis of pesticides in aqueous samples by magnetic solid‐phase extraction with high‐performance liquid chromatography

Three‐dimensional graphene‐supported mesoporous silica@Fe₃O₄ composites (mSiO₂@Fe₃O₄‐G) were prepared by modifying mesoporous SiO₂‐coated Fe₃O₄ onto hydrophobic graphene nanosheets through a simple adsorption co‐condensation method. The obtained composites possess unique properties of large surface area (332.9 m²/g), pore volume (0.68 cm³/g), highly open pore structure with uniform pore size (31.1 nm), as well as good magnetic separation properties. The adsorbent (mSiO₂@Fe₃O₄‐G) was used for the magnetic solid‐phase extraction of seven pesticides with benzene rings in different aqueous samples before high‐performance liquid chromatography. The main parameters affecting the extraction such as adsorbent amount, volume of elution solvent, time of extraction and desorption, salt effect, oscillation rate were investigated. Under the optimal conditions, this method provided low limits of detection (S/N = 3, 0.525–3.30 μg/L) and good linearity (5.0–1000 μg/L, R² > 0.9954). Method validation proved the feasibility of the developed adsorbent, which has a high extraction efficiency and excellent enhancement performance for pesticides in this study. The proposed method was successfully applied to real aqueous samples, and satisfactory recoveries ranging from 77.5 to 113.6% with relative standard deviations within 9.7% were obtained.     

Rapid magnetic solid‐phase extraction of Congo Red and Basic Red 2 from aqueous solution by ZIF‐8@CoFe2O4 hybrid composites

Core–shell metal–organic framework materials have attracted considerable attention mainly due to their enhanced or new physicochemical properties compared with their single‐component counterparts. In this work, a core–shell heterostructure of CoFe₂O₄‐Zeolitic Imidazolate Framework‐8 (ZIF‐8@CoFe₂O₄) is successfully fabricated and used as an solid‐phase extraction adsorbent to efficiently extract Congo Red and Basic Red 2 dyes from contaminated aqueous solution. Vibrating sample magnetometry indicates that the saturated magnetization of ZIF‐8@CoFe₂O₄ is 3.3 emu/g, which is large enough for magnetic separation. The obtained hybrid magnetic metal‐organic framework based material ZIF‐8@CoFe₂O₄ can remove the investigated dyes very fast within 1 min of the contact time. The adsorbent ZIF‐8@CoFe₂O₄ also shows a good reusability. After regeneration, the adsorbent can still exhibit high removal efficiency (～97%) toward Congo Red for five cycles of desorption–adsorption. This work reveals the great potential of core–shell ZIF‐8@CoFe₂O₄ sorbents for the fast separation and preconcentration of organic pollutants in aqueous solution before high‐performance liquid chromatography analysis.     

Ligand fishing of anti‐neurodegenerative components from Lonicera japonica using magnetic nanoparticles immobilised with monoamine oxidase B

In this work, monoamine oxidase B was immobilised onto magnetic nanoparticles to prepare a new type of affinity solid‐phase extraction adsorbent, which was used to extract the possible anti‐neurodegenerative components from the Lonicera japonica flower extracts. Coupled with high‐performance liquid chromatography with mass spectrometry, two monoamine oxidase B ligands were fished‐out and identified as isochlorogenic acid A and isochlorogenic acid C, which were found to be inhibitors of the enzyme for the first time, with similar half maximal inhibitory concentration values of 29.05 ± 0.49 and 29.77 ± 1.03 μM, respectively. Furthermore, equilibrium‐dialysis dissociation assay of enzyme‐inhibitor complex showed that both compounds have reversible binding patterns to monoamine oxidase B, and kinetic analysis demonstrated that they were mixed‐type inhibitors for monoamine oxidase B, with K_i and K_is values of 9.55 and 37.24 μM for isochlorogenic acid A, 9.53 and 35.50 μM for isochlorogenic acid C, respectively. The results indicated that isochlorogenic acid A and isochlorogenic acid C were the major active components responsible for the anti‐degenerative activity of the flowers of L. japonica, while magnetic nanoparticles immobilised monoamine oxidase B could serve as an efficient solid‐phase extraction adsorbent to specifically extract monoamine oxidase B inhibitors from complex herbal extracts.     

Automated solid‐phase extraction of phenolic acids using layered double hydroxide–alumina–polymer disks

The application of layered double hydroxide–Al₂O₃–polymer mixed‐matrix disks for solid‐phase extraction is reported for the first time. Al₂O₃ is embedded in a polymer matrix followed by an in situ metal‐exchange process to obtain a layered double hydroxide–Al₂O₃–polymer mixed‐matrix disk with excellent flow‐through properties. The extraction performance of the prepared disks is evaluated as a proof of concept for the automated extraction using sequential injection analysis of organic acids (p‐hydroxybenzoic acid, 3,4‐dihydroxybenzoic acid, gallic acid) following an anion‐exchange mechanism. After the solid‐phase extraction, phenolic acids were quantified by reversed‐phase high‐performance liquid chromatography with diode‐array detection using a core–shell silica–C18 stationary phase and isocratic elution (acetonitrile/0.5% acetic acid in pure water, 5:95, v/v). High sensitivity and reproducibility were obtained with limits of detection in the range of 0.12–0.25 μg/L (sample volume, 4 mL), and relative standard deviations between 2.9 and 3.4% (10 μg/L, n = 6). Enrichment factors of 34–39 were obtained. Layered double hydroxide–Al₂O₃–polymer mixed‐matrix disks had an average lifetime of 50 extractions. Analyte recoveries ranged from 93 to 96% for grape juice and nonalcoholic beer samples.     

Fabrication of glucose‐derived carbon‐decorated magnetic microspheres for extraction of bisphenols from water and tea drinks

Glucose‐derived carbon‐decorated magnetic microspheres were synthesized by an easy hydrothermal carbonization method and used as a high‐efficiency adsorbent to extract bisphenols in water and tea drinks. The as‐prepared carbon‐decorated magnetic microspheres had a well‐defined core–shell structure with a shell thickness of about 5 nm. The microspheres possessed high saturation magnetization at 60.8 emu/g and excellent chemical stability in aqueous solution. The experimental parameters affecting the extraction efficiency, including extraction time, pH, adsorbent dosage, desorption solvents, desorption time, and solution volume were evaluated. Electrostatic and π–π interactions were the major driving forces during extraction. Overall, a new magnetic solid‐phase extraction method of determining bisphenols was developed on the basis of as‐prepared magnetic microspheres. The method had a wide linear range, low limits of detection (0.03–0.10 µg/L), and high recoveries (85.4–104.6%).     

Dicationic polymeric ionic‐liquid‐based magnetic material as an adsorbent for the magnetic solid‐phase extraction of organophosphate pesticides and polycyclic aromatic hydrocarbons

Magnetic particles modified with a dicationic polymeric ionic liquid are described as a new adsorbent in magnetic solid‐phase extraction. They were obtained through the copolymerization of a 1,8‐di(3‐vinylimidazolium)octane‐based ionic liquid with vinyl‐modified SiO₂@Fe₃O₄, and were characterized by FTIR spectroscopy, X‐ray diffraction, and vibrating sample magnetometry. The modified magnetic particles are effective in the extraction of organophosphate pesticides and polycyclic aromatic hydrocarbons. Also, they can provide different extraction performance for the selected analytes including fenitrothion, parathion, fenthion, phoxim, phenanthrene, and fluoranthene, where the extraction efficiency is found to be in agreement with the hydrophobicity of analytes. Various factors influencing the extraction efficiency, such as, the amount of adsorbent, extraction, and desorption time, and type and volume of the desorption solvent, were optimized. Under the optimized conditions, a good linearity ranging from 1–100 μg/L is obtained for all analytes, except for parathion (2–200 μg/L), where the correlation coefficients varied from 0.9960 to 0.9998. The limits of detection are 0.2–0.8 μg/L, and intraday and interday relative standard deviations are 1.7–7.4% (n = 5) and 3.8–8.0% (n = 3), respectively. The magnetic solid‐phase extraction combined with high‐performance liquid chromatography can be applied for the detection of trace targets in real water samples with satisfactory relative recoveries and relative standard deviations.     

Fe3O4/reduced graphene oxide‐carbon nanotubes composite for the magnetic solid‐phase extraction and HPLC determination of sulfonamides in milk

A novel magnetic adsorbent Fe₃O₄/reduced graphene oxide‐carbon nanotubes, was prepared by one‐pot solvothermal synthesis method. It was characterized by scanning electron microscopy, X‐ray powder diffraction and vibrating sample magnetometry. The diameter of Fe₃O₄ microparticles was about 350 nm, which were covered by carbon nanotubes and reduced graphene oxide sheets, while carbon nanotubes inserted between the reduced graphene oxide sheets effectively prevented their aggregation. The composite had large surface area and good magnetic property, suiting for magnetic solid‐phase extraction and the determination of sulfonamides, by coupling with high‐performance liquid chromatography. Under the optimized conditions (including extraction time, amount of adsorbent, solution pH, ionic strength and desorption conditions), a good linear was achieved in the concentration range of 5–500 μg/L and the low limits of detection and low limits of quantification were 0.35–1.32 and 1.16–4.40 μg/L, respectively. The enrichment factors were estimated to be 24.72 to 30.15 fold. The proposed method was applied for the detection of sulfonamides in milk sample and the recoveries were 88.4–105.9%, with relative standard deviations of 0.74–5.38%.     

Preparation and quantification of the total phenolic products in Citrus fruit using solid‐phase extraction coupled with high‐performance liquid chromatography with diode array and UV detection

Citrus fruit is an important health‐promoting food that is rich in dietary phenolic metabolites. Traditional Chinese medicines, such as Zhishi and Zhiqiao, come from young and immature fruits of Citrus cultivars. The preparation of diversified bioactive phenolic products and establishment of the corresponding quality control methodology are challenging and necessary. In the current study, four types of solid‐phase extraction sorbents for the enrichment and clean‐up of the phenolic matrix were evaluated. A solid‐phase extraction column coated with Strata‐X was finally used in the procedure. Twenty phenolic compounds were selected to evaluate the extraction performances of the sorbents using high‐performance liquid chromatography analysis. Under the optimized conditions, good linearities were obtained with R² more than 0.9996 for all analytes with LODs of 0.04–1.012 μg/g. Intra‐ and interday relative standard deviation values were less than 3%, and the recovery was equal to or higher than 90.02%. Compared to non‐solid‐phase extraction process, the content of total phenolic products was elevated 35.55–68.48% with solid‐phase extraction. Finally, the developed and validated method was successfully applied to the discrimination of Zhishi samples from different species as well as Zhishi and Zhiqiao samples in different development stages.