Validation of a method for extraction of polycyclic aromatic hydrocarbons from sewage sludge and analysis by GC-MS

In the present study, the solid–liquid extraction with low temperature purification was validated for the determination of 16 polycyclic aromatic hydrocarbons from sewage sludge by gas chromatography-mass spectrometry. Recoveries ranged 70–114% for naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, benzo[a]anthracene and chrysene, while the compounds benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene, dibenzo[a,h]anthracene and benzo[g,h,i]perylene showed recoveries of between 40 and 70%. The relative standard deviation was less than 13% for all of the compounds. Negative matrix effect was observed on the 10 compounds with less retention time in the chromatographic analysis and positive matrix effect noticed on the others. The limits of quantification were from 2 to 20 μg kg^?1, about 30 times less than the maximum residue limit allowed in sludge by the European Union. The validated method produced quantification of 11 PAHs in one sludge sample at concentrations ranging 20–2000 μg kg^?1.     

采用新型固相萃取柱快速测定食用植物油中苯并［a］芘

研究了Bond Elut ENV新型固相萃取柱在食用植物油中苯并[a]芘快速检测中的应用,建立了快速测定食用植物油样品中苯并[a]芘残留量的固相萃取/液相色谱/荧光检测法。样品用正己烷溶解,固相萃取净化,SUPELCOSILTMLC-PAH(25 cm×4.6 mm,5μm)色谱柱分离,以乙腈-水(95∶5)为流动相,荧光检测(λex=297 nm,λem=408 nm),外标法定量。苯并[a]芘的检出限为0.3μg/kg,在1.0～50.0μg/L范围内线性关系良好,相关系数为0.999 6,方法的回收率为79%～102%,相对标准偏差不高于9.4%。该方法准确、实用、简便、快速,在食用植物油的苯并[a]芘残留量检测方面有广泛的应用前景。     

超高效液相色谱-大气压化学电离-三重四极杆质谱联用法快速测定食品中苯并[a]芘

建立了快速检测食品中苯并[a]芘的超高效液相色谱-三重四极杆质谱联用(UPLC-MS/MS)分析方法。样品用正己烷提取后,经分子印迹固相萃取柱净化,以甲醇和水作为流动相进行梯度洗脱,在XBridge BEH C18柱上实现分离,大气压化学电离(APCI)-三重四极杆质谱正离子MRM方式检测,以苯并[a]芘-d12作为内标的稳定同位素稀释法定量。方法的线性范围为0.07~50μg/kg,定量限为0.07μg/kg。平均加标回收率为86%~104%,相对标准偏差为2.3%~14%。该方法灵敏、准确,适用于食品中苯并[a]芘的测定,已应用于实际样品的检查。     

植物油中苯并芘含量测定研究

为建立固相萃取-液相色谱法测定植物油中苯并芘的检验方法,将植物油中的苯并芘用中性氧化铝固相萃取小柱萃取和净化后用反相色谱柱分离,荧光检测器进行了检测。结果表明,苯并芘质量浓度在0．001～0．1μg／mL范围内与峰面积具有良好的线性关系,相关系数r=0．9999,检测限为0．4μg／kg,回收率在88．1％～94．2％之间,RSD为2．42％,操作简便,对样液的净化效果好,结果准确可靠。     

高效液相色谱-荧光检测法测定橄榄油中4种多环芳烃

建立了高效液相色谱-荧光检测(HPLC-FLD)测定橄榄油中苯并[a]蒽、屈艹、苯并[b]荧蒽、苯并[a]芘4种多环芳烃(PAHs)的分析方法。橄榄油样品经异丙醇稀释,采用具有π-π特异性作用的固相萃取柱净化,Agilent ZORBAX Eclipse PAH色谱柱(100 m m×2.1 m m,1.8μm)分离,以水-乙腈为流动相,梯度洗脱,实现了4种化合物的基线分离,并用基质匹配校准溶液进行外标法定量。4种多环芳烃的线性范围为2.4~40μg/L,相关系数(r)为0.999 0~0.999 9,方法的定量限为0.147~0.413μg/L,加标回收率为95.5%~103.2%,日内和日间精密度(RSD)分别为0.10%~1.69%和2.48%~2.93%(n=5)。该法具有灵敏度高、检出限低、重复性好等特点,适用于橄榄油中4种PAHs快速、准确的定量检测。     

Trennung polyzyklisher aromatischer kohlenwasserstoffe durch hochdruckflössigkeitschromatographie: Vergleich einer bestimmung von benzo[a]pyren nach trennung an saäulen mit quervernetztem celluseacetat und einem reversed-phase system

Separation of polycyclic aromatic hydrocarbons by high-pressure liquid chromatography. Comparison of the determination of benzo(a)pyrene with separation on columns of cross-linked cellulose acetate and a reversed-phase system.

The behaviour of a new high-pressure liquid chromatographic support, i.e. a cross-linked cellulose acetate, as selective separation material for polycyclic aromatic hydrocarbons is discussed. The determination of benzo[a]pyrene is described by an example of separating a so-called benzpyrene fraction. The separation of the benzpyrene fraction was possible by combining column systems with aluminium oxide, cross-linked cellulose acetate or a reversed-phase system. By means of a fluore- scence detector 0.1-0.8 ng benzo[a]pyrene could be detected in 5μl injection volume.     

固相萃取-高效液相色谱-荧光法测定方便面和烤肠中的苯并[a]芘

建立了固相萃取-高效液相色谱-荧光法检测方便面和烤肠中苯并[a]芘的方法。采用正己烷作为提取溶剂,经苯并[a]芘专用固相萃取柱HiCapt Benzo富集净化,高效液相色谱-荧光法对样品中苯并[a]芘进行分离分析。苯并[a]芘的质量浓度在0.5~20.0μg/kg范围内与色谱峰面积呈良好的线性关系,相关系数R2为0.9997。方便面和烤肠中苯并[a]芘的加标回收率分别为92.2%~98.3%和95.9%~97.9%,日内和日间相对标准偏差分别为3.34%~5.01%和2.11%~4.07%。与传统方法相比,该方法快速简单、有机溶剂消耗少,在油炸烟熏食品的苯并[a]芘分析中具有较大应用前景。     

Rapid validated method for the analysis of benzo[a]pyrene in vegetable oils by using solid-phase microextraction-gas chromatography-mass spectrometry

A solid-phase microextraction method coupled with comprehensive gas chromatography and time-of-flight mass spectrometry for the determination of polycyclic aromatic hydrocarbons in vegetable oils has recently been reported. The present paper tested the possibility to use the solid-phase microextraction method coupled with one-dimensional gas chromatography-mass spectrometry of the only benzo[a]pyrene. Furthermore, an in-house validation for benzo[a]pyrene, used as a marker, as requested by the European regulation no. 208/2005, was carried out. Statistical tests were performed to elaborate the data. Linearity was satisfactory (r(2)=0.999), between about 0.5 and 15 microg/kg. Detection limit and quantification limit were 0.17 and 0.46 microg/kg, respectively. In-day and inter-day repeatability were less than 6% in both cases.     

Polycyclic aromatic hydrocarbons (PAHs) in edible oils by gas chromatography coupled with mass spectroscopy

The occurrence of polycyclic aromatic hydrocarbons (PAHs) in nine edible oils of three categories of oil samples, such as soy bean oil, mustard oil and coconut oil, has been studied to determine the contamination degree of this type of oil samples. Eight major carcinogenic polycyclic aromatic hydrocarbons (PAHs), such as naphthalene, anthracene, phenanthrene, fluorene, pyrene, crysene, benzo(a)pyrene and benzo(a)anthracene, were identified and quantified in the extract of edible oils collected from Bangladeshi Markets by gas chromatography and mass spectroscopy. All of the carcinogenic PAHs are not present in the edible oils. A few of the carcinogenic PAHs are present in the oils but it is within the permissible limit. The results for the recoveries of naphthalene, fluorene, phenanthrene, anthracene, pyrene, crysene, benzo(a)anthracene and benzo(a)pyrene were in the range of 56–84%. The limit of detection (LOD) of the GC–MS method, established at signals three times that of the noise for naphthalene, fluorene, phenanthrene, anthracene, pyrene, crysene, benzo(a)anthracene and benzo(a)pyrene, was 2.0–2.5 ng, respectively.     

改进的QuEChERS-液相色谱法检测蔬菜中的苯并(α)芘

采用改进的QuEChERS,对蔬菜样品进行提取、净化,用高效液相色谱仪/荧光检测器检测,建立了蔬菜中苯并(α)芘的测定方法.样品用乙腈提取,PSA+中性Al2O3小柱净化,以10mL正己烷-乙腈(95:5,体积比)洗脱小柱,外标法定量.苯并(α)芘的含量在1.0～20.0μg/kg范围内与峰面积呈良好线性,相关系数(r...     

Determination of benzo[a]pyrene in edible oils using phase‐transfer‐catalyst‐assisted saponification and supramolecular solvent microextraction coupled to HPLC with fluorescence detection

For the analysis of edible oils, saponification is well known as a useful method for eliminating oil matrices. The conventional approach is conducted with alcoholic alkali; it consumes a large volume of organic solvents and impedes the retrieval of analytes by microextraction. In this study, a low‐organic‐solvent‐consuming method has been developed for the analysis of benzo[a]pyrene in edible oils by high‐performance liquid chromatography with fluorescence detection. Sample treatment involves aqueous alkaline saponification, assisted by a phase‐transfer catalyst, and selective in situ extraction of the analyte with a supramolecular solvent. Comparison of the chromatograms of the oil extracts obtained by different microextraction methods showed that the supramolecular solvent has a better clean‐up effect for the unsaponifiable matter from oil matrices. The method offered excellent linearity over a range of 0.03– 5.0 ng mL⁻¹ (r > 0.999). Recovery rates varied from 94 to 102% (RSDs <5.0%). The detection limit and quantification limit were 0.06 and 0.19 μg kg⁻¹, respectively. The proposed method was applied for the analysis of 52 edible oils collected online in China; the analyte contents of 23 tested oil samples exceeded the maximum limit of 2 μg kg⁻¹ for benzo[a]pyrene set by the Commission Regulation of the European Union.     

Optimization of Pretreatment Procedures for Analysis of Polycyclic Aromatic Hydrocarbons in Charcoal-Grilled Pork

A method for analysis of 13 polycyclic aromatic hydrocarbons in charcoal-grilled pork was established by high performance liquid chromatography with ultraviolet detection. The cleanup and preconcentration steps include ultrasonic extraction, saponification, liquid-liquid extraction, and solid-phase extraction. Under the optimization experimental conditions, polycyclic aromatic hydrocarbons would be determined at trace level with recoveries between 68.5% and 102.8%. Additionally, the influence of grilling time on polycyclic aromatic hydrocarbons content was investigated. It was testified that when the roasting time reached 4 minutes under the experimental conditions, the content of carcinogen benzo(a)pyrene had exceeded the limit of the European Union.     

Development of a solid‐phase microextraction fiber by the chemical binding of graphene oxide on a silver‐coated stainless‐steel wire with an ionic liquid as the crosslinking agent

Graphene oxide was bonded onto a silver‐coated stainless‐steel wire using an ionic liquid as the crosslinking agent by a layer‐by‐layer strategy. The novel solid‐phase microextraction fiber was characterized by scanning electron microscopy, energy‐dispersive X‐ray spectroscopy and Raman microscopy. A multilayer graphene oxide layer was closely coated onto the supporting substrate. The thickness of the coating was about 4 μm. Coupled with gas chromatography, the fiber was evaluated using five polycyclic aromatic hydrocarbons (fluorene, anthracene, fluoranthene, 1,2‐benzophenanthrene, and benzo(a)pyrene) as model analytes in direct‐immersion mode. The main conditions (extraction time, extraction temperature, ionic strength, and desorption time) were optimized by a factor‐by‐factor optimization. The as‐established method exhibited a wide linearity range (0.5–200 μg/L) and low limits of determination (0.05–0.10 μg/L). It was applied to analyze environmental water samples of rain and river water. Three kinds of the model analytes were quantified and the recoveries of samples spiked at 10 μg/L were in the range of 92.3–120 and 93.8–115%, respectively. The obtained results indicated the fiber was efficient for solid‐phase microextraction analysis.     

Development and optimization of an HPLC–DAD method for quantification of six petroleum hydrocarbon compounds in aqueous samples

Benzene, toluene, and xylene isomers (BTXs) and pyrene, benzo(b)fluoranthene, and benzo(a)pyrene (polycyclic aromatic hydrocarbons) are common pollutants found in many industrial effluents and in aquifers due to fossil fuels spill from underground storage reservoirs. For these reasons, the determination of these compounds has gained importance in the last decades. In this work, a simultaneous, fast, and accurate quantification of six petroleum hydrocarbon compounds (such as BTXs, pyrene, benzo(b)fluoranthene, and benzo(a)pyrene) using a high-performance liquid chromatography–diode array detector method has been demonstrated. The proposed method is suitable for the direct aqueous sample evaluation and also brings advantages, including the use of small volumes of organic solvents, with high resolution, reducing the analysis cost. The method was also checked using synthetic and real samples, including those containing surfactants, commercial gasoline, and river water samples spiked with petroleum hydrocarbon compounds.     

Determination of polycyclic aromatic hydrocarbons from buzzards (Buteo buteo) and tawny owl (Strix aluco) by liquid chromatography with fluorescence detection

Supercritical fluid extraction was applied to the determination of naturally contaminated polycyclic aromatic hydrocarbons (PAHs) in bird tissue by liquid chromatography with fluorescence detection (LC-FL). Recoveries (> 90%) and relative standard deviations (< or = 7.7%) were satisfactory. The levels of 10 PAHs were analyzed in 6 classes of tissues (heart, liver, intestine, muscle, lung, and kidney) of 10 buzzards and 2 tawny owls, predatory birds from the Galicia (northwest Spain). The PAHs found most abundantly were pyrene, fluoranthene, benzo[a]anthracene, and anthracene. Chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[ghi]perylene, and indeno[1,2,3-cd]pyrene were not detected. Intestine, kidney, and lung were more polluted than other tissues.     

Analysis of EU priority polycyclic aromatic hydrocarbons in food supplements using high performance liquid chromatography coupled to an ultraviolet, diode array or fluorescence detector

High performance liquid chromatography coupled to an ultraviolet, diode array or fluorescence detector (HPLC/UV-FLD) has been used to set up a method to detect the 15(+1) EU priority polycyclic aromatic hydrocarbons (PAHs) in food supplements covering the categories of dried plants and plant extracts excluding oily products. A mini validation was performed and the following parameters have been determined: limit of detection, limit of quantification, precision, recovery and linearity. They were in close agreement with quality criteria described in the Commission Regulation (EC) No 333/2007 concerning the PAH benzo[a]pyrene in foodstuffs, except the not fluorescent cyclopenta[c,d]pyrene for which the UV detection leads to a higher limit of detection. Analysis of twenty commercial food supplements covering mainly the class of dried plants was performed to evaluate their PAHs contamination levels and to test the applicability of the method to various plant matrices. Fifty percent of analyzed samples showed concentration exceeding 2 μg kg⁻¹ for one or more PAHs.     

气相色谱-串联质谱法同时测定卷烟滤嘴中15种多环芳烃

建立了气相色谱-串联质谱同时检测卷烟滤嘴中15种多环芳烃的方法。卷烟滤嘴用二氯甲烷振荡萃取后,经0.22μm有机相滤膜过滤,采用DB-5MS色谱柱(30 m×0.25 mm,0.25μm)进行分离,电子轰击源、正离子模式下以多反应监测模式进行检测,内标法进行定量。15种多环芳烃(苊烯、苊、芴、菲、蒽、荧蒽、芘、苯并[a]蒽、屈、苯并[b]荧蒽、苯并[k]荧蒽、苯并[a]芘、二苯并[a,h]蒽、苯并[g,h,i]苝和茚并[1,2,3-c,d]芘)的线性关系良好,相关系数(R~2)为0.991 4~0.999 9。15种多环芳烃在低、中、高3个添加水平下的平均回收率为81.6%~111.2%;除了芴在低添加水平时相对标准偏差为19.2%外,其他相对标准偏差均小于16%。15种多环芳烃的检出限为0.02~0.24 ng/滤嘴,定量限为0.04~0.80 ng/滤嘴。方法前处理简便,具有快速、准确、灵敏度高及重复性好的优点,适用于卷烟滤嘴中多环芳烃的分析。     

A novel application of nylon membranes to the luminescent determination of benzo[a]pyrene at ultra trace levels in water samples

Very simple and highly sensitive methods are presented for the determination of benzo[a]pyrene, one of the most carcinogenic polycyclic aromatic hydrocarbons (PAHs). The approaches are based on solid-phase extraction of the analyte on a nylon membrane via a syringe procedure, and its fluorescent or phosphorescent determination on the solid surface. While the native fluorescence of benzo[a]pyrene retained on a nylon surface is measured directly, room-temperature phosphorescence is induced by spotting a few microlitres of thallium(I) nitrate solution on the surface (heavy-atom effect). An enhancement of the phosphorescence signal was corroborated when the measurements were carried under a nitrogen atmosphere. The analytical figures of merit obtained under the best experimental conditions demonstrate the capability of detecting benzo[a]pyrene at a sub-parts-per-trillion (sub-ng L⁻¹) level. The potential interference from other common PAHs and also from different metal ions was studied. The feasibility of determining benzo[a]pyrene in real samples was successfully evaluated through the analysis of spiked tap, underground and mineral water samples of different origins. Recoveries obtained from spiked river waters were successfully compared with those provided by a reference method, through rigorous statistical analysis.     

Vortex‐assisted extraction combined with dispersive liquid–liquid microextraction for the determination of polycyclic aromatic hydrocarbons in sediment by high performance liquid chromatography

A simple, rapid, and efficient method, vortex‐assisted extraction followed by dispersive liquid–liquid microextraction (DLLME) has been developed for the extraction of polycyclic aromatic hydrocarbons (PAHs) in sediment samples prior to analysis by high performance liquid chromatography fluorescence detection. Acetonitrile was used as collecting solvent for the extraction of PAHs from sediment by vortex‐assisted extraction. In DLLME, PAHs were rapidly transferred from acetonitrile to dichloromethane. Under the optimum conditions, the method yields a linear calibration curve in the concentration range from 10 to 2100 ng g^?1 for fluorene, anthracene, chrysene, benzo[k]fluoranthene, and benzo[a]pyrene, and 20 to 2100 ng g^?1 for other target analytes. Coefficients of determinations ranged from 0.9986 to 0.9994. The limits of detection, based on signal‐to‐noise ratio of three, ranged from 2.3 to 6.8 ng g^?1. Reproducibility and recoveries was assessed by extracting a series of six independent sediment samples, which were spiked with different concentration levels. Finally, the proposed method was successfully applied in analyses of real nature sediment samples. The proposed method extended and improved the application of DLLME to solid samples, which greatly shorten the extraction time and simplified the extraction process.     

Room temperature phosphorescence analyses of polycyclic aromatic hydrocarbons using an imaging sensing system combined with a bifurcated optical fiber and a cooled charge coupled device detector

This paper presents a development of a solid support RT phosphorescence procedure for the determination of polycyclic aromatic hydrocarbons, based on the use of a Xenon flash lamp as the excitation source, a fiber optic sensor as a guide of light, an imaging spectrograph and a cooled two dimensional charge coupled device as the detector. Non fluorescent Whatman N degrees 1 filter paper was used as the solid substrate and, thallium nitrate and sodium iodide were used to enhance room temperature phosphorescence of pyrene, benzo (a) anthracene, naphtalene, phenanthrene, dibenzothiophene, fluorene, coronene and fluoranthene. Analytical curves of eight phosphors give linear dynamic ranges from one and a half to two decades and limits of detection of femtomolar to picomolar/spot were reported. Quantitative analyses in mixtures were also carried out using the internal standard method. Results led to a 10% better accuracy for determinations of pyrene and benzo (a) anthracene.