Mesoporous Silica‐coated Magnetic Nanoparticles for Mixed Hemimicelles Solid‐phase Extraction of Phthalate Esters in Environmental Water Samples with Liquid Chromatographic Analysis

To extract, preconcentrate and determine the trace level of environmental contaminants, a novel mixed hemimicelles solid‐phase extraction (MHSPE) method based on mesoporous silica‐coated magnetic nanoparticles (Fe₃O₄/meso‐SiO₂ NPs) as adsorbent was developed for extraction of phthalate esters from water samples. The Fe₃O₄/meso‐SiO₂ NPs were synthesized by using a combination of hydrothermal method and sol‐gel method. The obtained Fe₃O₄/meso‐SiO₂ NPs possessed a large surface area (570 m²/g), superparamagnetism, and uniform mesopores (2.8 nm). MHSPE parameters, such as the amount of surfactant, pH of sample, shaking and separation time, eluent and breakthrough volume that may influence the extraction of analytes greatly, were further investigated. Under the optimized conditions, the extraction was completed in 20 min and a concentration factor of 500 was achieved by extracting 250 mL water sample. Detection limits obtained of butyl‐benzyl phthalate (BBP), di‐n‐butyl phthalate (DnBP), di‐(2‐ethylhexyl) phthalate (DEHP) and di‐n‐cotyl phthalate (DnOP) were 12, 21, 12, and 32 ng/L, respectively. The proposed method exhibited high extraction efficiency and relatively short time for extracting the target compounds.     

Selective enrichment of catecholamines using iron oxide nanoparticles followed by CE with UV detection

This study examines the use of unmodified magnetite nanoparticles (Fe₃O₄ NPs) for selective extraction and enrichment of the catecholamines dopamine (DA), noradrenaline (NE), and adrenaline (E), prior to analysis using capillary electrophoresis with UV detection. Coordination between Fe³⁺ on‐the‐surface Fe₃O₄ NPs and the catechol moiety of catecholamines enables Fe₃O₄ NPs to capture catecholamines from an aqueous solution. We obtained maximum loading of catecholamines on the NP surface by adjusting the pH of the solution to 7.0. In addition, catecholamine loading on the Fe₃O₄ NPs increased in conjunction with NP concentrations. H₃PO₄ was found to be efficient for the removal of adsorbed catecholamines on the NP surface. Adding 1.2% poly(diallyldimethylammonium chloride) to the background electrolyte resulted in a baseline separation of the liberated catecholamines within 20 min. Under optimal extraction and separation conditions, the limit of detections at a S/N ratio of 3 for E, NE, and DA were 9, 8, and 10 nM, respectively. Significantly, the combination of a phenylboronate‐containing spin column and the proposed method was successfully applied to the determination of NE and DA in human urine and NE in Portulaca oleracea L. leaves.     

Ultrafast Preparation of Monodisperse Fe3O4 Nanoparticles by Microwave‐Assisted Thermal Decomposition

Thermal decomposition, as the main synthetic procedure for the synthesis of magnetic nanoparticles (NPs), is facing several problems, such as high reaction temperatures and time consumption. An improved a microwave‐assisted thermal decomposition procedure has been developed by which monodisperse Fe₃O₄ NPs could be rapidly produced at a low aging temperature with high yield (90.1 %). The as‐synthesized NPs show excellent inductive heating and MRI properties in vitro. In contrast, Fe₃O₄ NPs synthesized by classical thermal decomposition were obtained in very low yield (20.3 %) with an overall poor quality. It was found for the first time that, besides precursors and solvents, magnetic NPs themselves could be heated by microwave irradiation during the synthetic process. These findings were demonstrated by a series of microwave‐heating experiments, Raman spectroscopy and vector‐network analysis, indicating that the initially formed magnetic Fe₃O₄ particles were able to transform microwave energy into heat directly and, thus, contribute to the nanoparticle growth.     

Mixed hemimicelles solid-phase extraction of chlorophenols in environmental water samples with 1-hexadecyl-3-methylimidazolium bromide-coated Fe3O4 magnetic nanoparticles with high-performance liquid chromatographic analysis

In this paper, 1-hexadecyl-3-methylimidazolium bromide (C₁₆mimBr)-coated Fe₃O₄ magnetic nanoparticles (NPs) as an adsorbent of mixed hemimicelles solid-phase extraction was investigated for the preconcentration of two chlorophenols (CPs) in environmental water samples prior to HPLC with UV detection at 285 nm. The high surface area and excellent adsorption capacity of the Fe₃O₄ NPs after modification with C₁₆mimBr were utilized adequately in the SPE process. By the rapid isolation of Fe₃O₄ NPs through placing a strong magnet on the bottom of beaker, the time-consuming preconcentration process of loading large volume sample in conventional SPE method with a column can be avoided. A comprehensive study of the adsorption conditions such as the zeta-potential of Fe₃O₄ NPs, added amounts of C₁₆mimBr, pH value, standing time and maximal extraction volume were also presented. Under optimized conditions, two analytes of 2,4-dichlorophenol (2,4-DCP) and 2,4,6-trichlorophenol (2,4,6-TCP) were quantitatively determined. The method was then used to determine the two CPs in real environmental water samples. The accuracy of method was evaluated by recovery measurements on spiked samples. Good recovery results (74–90%) were achieved. It is important to note that satisfactory preconcentration factors and extraction recoveries for the two CPs were obtained with only a small amount of Fe₃O₄ NPs (40 mg) and C₁₆mimBr (24 mg).     

Preparation of alumina-coated magnetite nanoparticle for extraction of trimethoprim from environmental water samples based on mixed hemimicelles solid-phase extraction

In this study, a new type of alumina-coated magnetite nanoparticles (Fe₃O₄/Al₂O₃ NPs) modified by the surfactant sodium dodecyl sulfate (SDS) has been successfully synthesized and applied for extraction of trimethoprim (TMP) from environmental water samples based on mixed hemimicelles solid-phase extraction (MHSPE). The coating of alumina on Fe₃O₄ NPs not only avoids the dissolving of Fe₃O₄ NPs in acidic solution, but also extends their application without sacrificing their unique magnetization characteristics. Due to the high surface area of these new sorbents and the excellent adsorption capacity after surface modification by SDS, satisfactory concentration factor and extraction recoveries can be produced with only 0.1 g Fe₃O₄/Al₂O₃ NPs. Main factors affecting the adsolubilization of TMP such as the amount of SDS, pH value, standing time, desorption solvent and maximal extraction volume were optimized. Under the selected conditions, TMP could be quantitatively extracted. The recoveries of TMP by analyzing the four spiked water samples were between 67 and 86%, and the relative standard deviation (RSD) ranged from 2 to 6%. Detection and quantification limits of the proposed method were 0.09 and 0.24 μg L⁻¹, respectively. Concentration factor of 1000 was achieved using this method to extract 500 mL of different environmental water samples. Compared with conventional SPE methods, the advantages of this new Fe₃O₄/Al₂O₃ NPs MHSPE method still include easy preparation and regeneration of sorbents, short times of sample pretreatment, high extraction yields, and high breakthrough volumes. It shows great analytical potential in preconcentration of organic compounds from large volume water samples.     

Reprint of: Extraction of fluoxetine from aquatic and urine samples using sodium dodecyl sulfate-coated iron oxide magnetic nanoparticles followed by spectrofluorimetric determination

A new method based on the combination of magnetic solid phase extraction (MSPE) and spectrofluorimetric determination was developed for isolation and preconcentration of fluoxetine form aquatic and biological samples using sodium dodecyl sulfate (SDS) coated Fe₃O₄ nanoparticles (NPs) as a sorbent. The unique properties of Fe₃O₄ NPs including high surface area and strong magnetism were utilized effectively in the MSPE process. Effect of different parameters influencing the extraction efficiency of fluoxetine including the amount of Fe₃O₄ and SDS, pH value, sample volume, extraction time, desorption solvent and time were optimized. Under optimized condition, the method was successfully applied to the extraction of fluoxetine from water and urine samples and absolute recovery amount of 85%, detection limit of 20 μg L⁻¹ and a relative standard deviation (RSD) of 1.4% were obtained. The method linear response was over a range of 50–1000 μg L⁻¹ with R² = 0.9968. The relative recovery in different aquatic and urine matrices were investigated and values of 80% to 104% were obtained. The whole procedure showed to be conveniently fast, efficient and economical for extraction of fluoxetine from environmental and biological samples.     

Dispersive liquid–liquid microextraction based on amine‐functionalized Fe3O4 nanoparticles for the determination of phenolic acids in vegetable oils by high‐performance liquid chromatography with UV detection

A novel dispersive liquid–liquid microextraction method based on amine‐functionalized Fe₃O₄ magnetic nanoparticles was developed for the determination of six phenolic acids in vegetable oils by high‐performance liquid chromatography. Amine‐functionalized Fe₃O₄ was synthesized by a one‐pot solvothermal reaction between Fe₃O₄ and 1,6‐hexanediamine and characterized by transmission electron microscopy and Fourier transform infrared spectrophotometry. A trace amount of phosphate buffer solution (extractant) was adsorbed on bare Fe₃O₄‐NH₂ nanoparticles by hydrophilic interaction to form the “magnetic extractant”. Rapid extraction could be achieved while the “magnetic extractant” on amine‐functionalized Fe₃O₄ nanoparticles was dispersed in the sample solution by vortexing. After extraction, the “magnetic extractant” was collected by application of an external magnet. Some important parameters, such as pH and volume of extraction and desorption solvents, the extraction and desorption time needed were carefully investigated and optimized to achieve the best extraction efficiency. Under the optimal conditions, satisfactory extraction recoveries were obtained for the six phenolic acids in the range of 84.2–106.3%. Relative standard deviations for intra‐ and inter‐day precisions were less than 6.3 and 10.0%, respectively. Finally, the established method was successfully applied for the determination of six phenolic acids in eight kinds of vegetable oils.     

Separation of chiral compounds using magnetic molecularly imprinted polymer nanoparticles as stationary phase by microchip capillary electrochromatography

In this work, a simple and rapid approach was developed for separation and detection of chiral compounds based on a magnetic molecularly imprinted polymer modified poly(dimethylsiloxane) (PDMS) microchip coupled with electrochemical detection. Molecularly imprinted polymers were prepared employing Fe₃O₄ nanoparticles (NPs) as the supporting substrate and norepinephrine as the functional monomer in the presence of template molecule in a weak alkaline solution. After extracting the embedded template molecules, Fe₃O₄@polynorepinephrine NPs (MIP–Fe₃O₄@PNE NPs) showed specific molecular recognition selectivity and high affinity towards the template molecule, which were then used as stationary phase of microchip capillary electrochromatography for chiral compounds separation. Mandelic acid and histidine enantiomers were used as model compounds to test the chiral stationary phase. By using R‐mandelic acid as the template molecule, mandelic acid enantiomer was effectively separated and detected on the MIP‐Fe₃O₄@PNE NPs modified PDMS microchip. Moreover, the successful separation of histidine enantiomers on the MIP–Fe₃O₄@PNE NPs modified microchip using L‐histidine as template molecule was also achieved.     

Determination of sulfadimethoxine in milk with aptamer‐functionalized Fe3O4/graphene oxide as magnetic solid‐phase extraction adsorbent prior to HPLC

An aptamer (Apt) functionalized magnetic material was prepared by covalently link Apt to Fe₃O₄/graphene oxide (Fe₃O₄/GO) composite by 1‐ethyl‐3‐(3‐dimethylaminopropyl) carbodiimide hydrochloride and N‐hydroxysuccinimide, and then characterized by FTIR spectroscopy, X‐ray diffraction, and vibration sample magnetometry. The obtained composite of Fe₃O₄/GO/Apt was employed as magnetic solid‐phase extraction adsorbent for the selective preconcentration of sulfadimethoxine prior to analysis by high‐performance liquid chromatography. Under the optimal conditions (sample pH of 4.0, sorbent dosage of 20 mg, extraction time of 3 h, and methanol‐5% acetic acid solution as eluent), a good linear relationship was obtained between the peak area and concentration of sulfadimethoxine in the range of 5.0 to 1500.0 µg/L with correlation coefficient of 0.9997. The limit of detection (S/N = 3) was 3.3 µg/L. The developed method was successfully applied to the analysis of sulfadimethoxine in milk with recoveries in the range of 75.9‐92.3% and relative standard deviations less than 8.1%. The adsorption mechanism of Fe₃O₄/GO/Apt toward sulfadimethoxine was studied through the adsorption kinetics and adsorption isotherms, and the results show that the adsorption process fits well with the pseudo‐second‐order kinetic model and the adsorbate on Fe₃O₄/GO/Apt is multilayer and heterogeneous.     

One‐step synthesized magnetic MIL‐101(Cr) for effective extraction of triazine herbicides from rice prior to determination by liquid chromatography‐tandem mass spectrometry

The magnetic metal‐organic framework MIL‐101(Cr) material‐based solid‐phase extraction method coupled with high‐performance liquid chromatography and tandem mass spectrometry was applied to extract seven triazine herbicides in rices. Fe₃O₄/MIL‐101(Cr) was synthesized using reduction‐precipitation method, in which steps including pre‐synthesis and modification of Fe₃O₄ nanoparticles were by‐passed. Various parameters including extraction solvent type and volume, ultrasonic extraction time, amount of Fe₃O₄/MIL‐101(Cr) microspheres, adsorption time, desorption volume and time were investigated. Under optimal conditions, the proposed method had the limit of detection (S/N = 3) and the limit of quantification (S/N = 10) of 1.08–18.10 and 3.60–60.20 pg/g, respectively. Relative standard deviations calculated for all herbicides with concentrations of 2 and 20 ng/g were in the range of 0.5 to 13% (n = 3). In addition, at the two above‐mentioned concentrations, the method achieved relative recoveries percentages of 79.3 to 116.7% when applied to determine the triazine herbicides in real samples spiked. This rapid, green, non‐polluting, pre‐concentrated extraction method was successfully developed and applied to analyze herbicides in rice samples.     

Aptamer‐functionalized Fe3O4 magnetic nanoparticles as a solid‐phase extraction adsorbent for the selective extraction of berberine from Cortex phellodendri

The extraction adsorbent was fabricated by immobilizing the highly specific recognition and binding of aptamer onto the surface of Fe₃O₄ magnetic nanoparticles, which not only acted as recognition elements to recognize and capture the target molecule berberine from the extract of Cortex phellodendri , but also could favor the rapid separation and purification of the bound berberine by using an external magnet. The developed solid‐phase extraction method in this work was useful for the selective extraction and determination of berberine in Cortex phellodendri extracts. Various conditions such as the amount of aptamer‐functionalized Fe₃O₄ magnetic nanoparticles, extraction time, temperature, pH value, Mg²⁺ concentration, elution time and solvent were optimized for the solid‐phase extraction of berberine. Under optimal conditions, the purity of berberine extracted from Cortex phellodendri was as high as 98.7% compared with that of 4.85% in the extract, indicating that aptamer‐functionalized Fe₃O₄ magnetic nanoparticles‐based solid‐phase extraction method was very effective for berberine enrichment and separation from a complex herb extract. The applicability and reliability of the developed solid‐phase extraction method were demonstrated by separating berberine from nine different concentrations of one Cortex phellodendri extract. The relative recoveries of the spiked solutions of all the samples were between 95.4 and 111.3%, with relative standard deviations ranging between 0.57 and 1.85%.     

Organometallic assembling of chitosan‐Iron oxide nanoparticles with their antifungal evaluation against Rhizopus oryzae

The ever‐increasing resistance of plant microbes towards fungicides and bactericides has been causing serious threat to plant production in recent years. For the development of an effective antifungal agent, we introduce a novel hydrothermal protocol for synthesis of chitosan iron oxide nanoparticles (CH‐Fe₂O₃ NPs) using acetate buffer of low pH 5.0 for intermolecular interaction of Fe₂O₃ NPs and CH. The composite structure and elemental elucidation were carried out by using X‐ray power diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive X‐ray (EDX), Transmission Electron Microscopy (TEM), Fourier Transformed Infrared Spectroscopy (FTIR) and Ultraviolet Visible Absorption Spectroscopy (UV–vis spectroscopy). Additionally, antifungal activity was evaluated both In vitro and In vivo against Rhizopus oryzae which is causing fruit rot disease of strawberry. We compared different concentrations (0.25%, 0.50%, 075% and 1%) of CH‐Fe₂O₃ NPs and 50% synthetic fungicide (Matalyxal Mancozab) to figure out suitable concentration for application in the field. XRD analysis showed a high crystalline nature of the NPs with average size of 52 nanometer (nm). SEM images revealed spherical shape with size range of 50–70 nm, whereas, TEM also revealed spherical shape, size ranging from 0 nm to 80 nm. EDX and FTIR results revealed presence of CH on surface of Fe₂O₃ NPs. The band gap measurement showed peak 317–318 nm for bare Fe₂O₃ NPs and CH‐Fe₂O₃ NPs respectively. Antifungal activity in both In vitro and In vivo significantly increased with increase in concentration. The overall results revealed high synergetic antifungal potential of organometallic CH‐Fe₂O₃ NPs against Rhizopus oryzae and suggest the use of CH‐Fe₂O₃ NPs against other Phyto‐pathological diseases due to biodegradable nature.     

Dispersive admicelle solid‐phase extraction based on sodium dodecyl sulfate coated Fe3O4 nanoparticles for the selective adsorption of three alkaloids in Gegen‐Qinlian oral liquid before high‐performance liquid chromatography

A novel dispersive admicelle solid‐phase extraction method based on sodium dodecyl sulfate‐coated Fe₃O₄ nanoparticles was developed for the selective adsorption of berberine, coptisine, and palmatine in Gegen‐Qinlian oral liquid before high‐performance liquid chromatography. Fe₃O₄ nanoparticles were synthesized by a chemical coprecipitation method and characterized by using transmission electron microscopy. Under acidic conditions, the surface of Fe₃O₄ nanoparticles was coated with sodium dodecyl sulfate to form a nano‐sized admicelle magnetic sorbent. Owing to electrostatic interaction, the alkaloids were adsorbed onto the oppositely charged admicelle magnetic nanoparticles. The quick separation of the analyte‐adsorbed nanoparticles from the sample solution was performed by using Nd‐Fe‐B magnet. Best extraction efficiency was achieved under the following conditions: 800 μL Fe₃O₄ nanoparticles suspension (20 mg/mL), 150 μL sodium dodecyl sulfate solution (10 mg/mL), pH 2, and vortexing time 2 min for the extraction of alkaloids from 10 mL of diluted sample. Four hundred microliters of methanol was used to desorb the alkaloids by vortexing for 1 min. Satisfactory extraction recoveries were obtained in the range of 85.9–120.3%, relative standard deviations for intra‐ and interday precisions were less than 6.3 and 10.0%, respectively. Finally, the established method was successfully applied to analyze the alkaloids in two batches of Gegen‐Qinlian oral liquids.     

Advanced Sensing of Antibiotics with Magnetic Gold Nanocomposite: Electrochemical Detection of Chloramphenicol

The sensing and accurate determination of antibiotics in various environments represents a big challenge, mainly owing to their widespread use in medicine, veterinary practice, and other fields. Therefore, a new, simple electrochemical sensor for the detection of antibiotic chloramphenicol (CAP) has been developed in this work. The amplification strategy of the sensor is based on the application of magnetite nanostructures stabilized with carboxymethyl cellulose (Fe₃O₄‐CMC) and decorated with nanometer‐sized Au nanoparticles (NPs) (Fe₃O₄‐CMC@Au). In this case, CMC serves as a stabilizing agent, preventing the aggregation of Fe₃O₄ NPs, and hence, enabling the kinetic barrier for electron transport to be overcome, and the Au NPs serve as an electron‐conducting tunnel for better electron transport. As a proof of concept, the developed nanosensor is used for the detection of CAP in human urine samples, giving a recovery value of around 97 %, which indicates the high accuracy of the as‐prepared nanosensor.     

Microscale solid phase extraction of glyphosate and aminomethylphosphonic acid in water and guava fruit extract using alumina-coated iron oxide nanoparticles followed by capillary electrophoresis and electrochemiluminescence detection

A microscale solid-phase extraction (SPE) method using alumina-coated iron oxide nanoparticles (Fe₃O₄@Al₂O₃ NPs) as the affinity adsorbent for glyphosate (GLY) and its major metabolite aminomethylphosphonic acid (AMPA) in aqueous solution is reported. One milligram of Fe₃O₄@Al₂O₃ NPs was employed to extract both analytes in 5 ml of aqueous solution. After 5 min extraction, magnetic NPs were isolated from sample solution by employing an external magnet. Followed by rinsing the NPs with 5 μl of 20 mM Na₄P₂O₇ solution for 5 min, the extract was directly analyzed using the derivatization-free CE-electrochemiluminescence (CE-ECL) method. With a sample-to-extract volume ratio of 1000, the enrichment factors for GLY and AMPA were 460 and 64, respectively. The limits of detection (LODs) were 0.3 and 30 ng ml⁻¹ for GLY and AMPA in water, respectively. The developed method was applied to the analysis of GLY in guava fruit. The LOD of GLY in guava was 0.01 μg g⁻¹. Total analysis time including sample pretreatment, SPE and CE-ECL was less than 1 h.     

Peapod‐Type Nanocomposites through the In Situ Growth of Gold Nanoparticles within Preformed Hexaniobate Nanoscrolls

A facile in situ method to grow Au nanoparticles (NPs) in hexaniobate nanoscrolls is applied to the formation of plasmonic Au@hexaniobate and bifunctional plasmonic‐magnetic Au‐Fe₃O₄@hexaniobate nanopeapods (NPPs). Utilizing a solvothermal treatment, rigid multiwalled hexaniobate nanoscrolls and partially filled Fe₃O₄@hexaniobate NPPs were first fabricated. These nanostructures were then used as templates for the controlled in situ growth of Au NPs. The resulting peapod structures exhibited high filling fractions and long‐range uniformity. Optical measurements showed a progressive red shift in plasmonic behavior between Au NPs, Au NPPs, and Au‐Fe₃O₄ NPPs; magnetic studies found that the addition of gold in the Fe₃O₄@hexaniobate NPPs reduced interparticle coupling effects. The development of this approach allows for the routine bulk preparation of noble‐metal‐containing bifunctional nanopeapod materials.     

Supercritical Carbon Dioxide Assisted Deposition of Fe3O4 Nanoparticles on Hierarchical Porous Carbon and Their Lithium‐Storage Performance

A composite of highly dispersed Fe₃O₄ nanoparticles (NPs) anchored in three‐dimensional hierarchical porous carbon networks (Fe₃O₄/3DHPC) as an anode material for lithium‐ion batteries (LIBs) was prepared by means of a deposition technique assisted by a supercritical carbon dioxide (scCO₂)‐expanded ethanol solution. The as‐synthesized Fe₃O₄/3DHPC composite exhibits a bimodal porous 3D architecture with mutually connected 3.7 nm mesopores defined in the macroporous wall on which a layer of small and uniform Fe₃O₄ NPs was closely coated. As an anode material for LIBs, the Fe₃O₄/3DHPC composite with 79 wt % Fe₃O₄ (Fe₃O₄/3DHPC‐79) delivered a high reversible capacity of 1462 mA h g^?1 after 100 cycles at a current density of 100 mA g^?1, and maintained good high‐rate performance (728, 507, and 239 mA h g^?1 at 1, 2, and 5 C, respectively). Moreover, it showed excellent long‐term cycling performance at high current densities, 1 and 2 A g^?1. The enhanced lithium‐storage behavior can be attributed to the synergistic effect of the porous support and the homogeneous Fe₃O₄ NPs. More importantly, this straightforward, highly efficient, and green synthetic route will definitely enrich the methodologies for the fabrication of carbon‐based transition‐metal oxide composites, and provide great potential materials for additional applications in supercapacitors, sensors, and catalyses.     

Solid Phase Extraction of Trace Amounts of Cadmium with Cetyltrimethylammonium Bromide‐Coated Magnetic Nanoparticles Prior to Its Determination by Flame Atomic Absorption Spectrometry

A solid‐phase extraction (SPE) method has been presented for the selective separation and preconcentration of trace amounts of cadmium using cetyltrimethylammonium bromide (CTAB)‐coated Fe₃O₄ nanoparticles (NPs). The method is based on the sorption of cadmium as CdI₄^2? complex on the positively charged surface of the CTAB‐coated Fe₃O₄ NPs. The preconcentrated cadmium is then desorbed from the surface of the sorbent and is determined by flame atomic absorption spectrometry. The influences of the experimental parameters including pH of the solutions, amount of surfactant, iodide concentration, sample volume, eluent type and volume on the recovery of the analyte ions were investigated. Under the optimum conditions by the extraction of 500 mL of aqueous samples, a preconcentration factor of 250 was achieved. The detection limit (3s) was 0.06 μg L^?1, and the relative standard deviations at 0.5 and 5 μg L^?1 levels of cadmium (n = 10) were 3.2 and 1.9% respectively. The proposed method was successfully applied to the determination of cadmium in water samples. The accuracy was evaluated through the recovery experiments and independent analysis by the graphite furnace atomic absorption spectrometry (GFAAS).     

Pectin mediated green synthesis of Fe3O4/Pectin nanoparticles under ultrasound condition as an anti-human colorectal carcinoma bionanocomposite

This work described the one-pot synthesis of apple pectin encapsulated Fe₃O₄ nanoparticles (Fe₃O₄/Pectin NPs) which is prepared by co-precipitation of Fe(II/(III) ions in alkaline solution mediated by pectin under ultrasound condition. This process led to formation of magnetic nanoparticles within the network of pectin. Physicochemical characterization of the as-synthesized Fe₃O₄/Pectin NPs was carried out through electron microscopy (SEM and TEM), energy dispersive X-ray spectroscopy (EDX), vibrating sample magnetometer (VSM) and X-ray diffraction (XRD). The in vitro cytotoxic and anti-colorectal cancer effects of biologically synthesized Fe₃O₄/Pectin NPs against Ramos.2G6.4C10, HCT-8 [HRT-18], HCT 116, and HT-29 cancer cell lines were assessed. The anti-colorectal cancer properties of the Fe₃O₄/Pectin NPs could significantly remove Ramos.2G6.4C10, HCT-8 [HRT-18], HCT 116, and HT-29 cancer cell lines in a time and concentration-dependent manner by MTT assay. The IC₅₀ of the Fe₃O₄/Pectin NPs were 317, 337, 187, and 300 µg/mL against Ramos.2G6.4C10, HCT-8 [HRT-18], HCT 116, and HT-29 cancer cell lines. The antioxidant activity of Fe₃O₄/Pectin NPs was determined by DPPH method. The Fe₃O₄/Pectin NPs showed the high antioxidant activity according to the IC₅₀ value. It seems that the anti-human colorectal cancer effect of recent nanoparticles is due to their antioxidant effects.     

Removal of acidic interferences in multi-pesticides residue analysis of fruits using modified magnetic nanoparticles prior to determination via ultra-HPLC-MS/MS

The authors describe magnetite (Fe₃O₄) nanoparticles modified with 3-(N,N-diethylamino) propyltrimethoxysilane (Fe₃O₄-PSA NPs) for use as a sorbent for dispersive solid phase extraction of pesticide residues. The Fe₃O₄-PSA NPs were prepared by silanizing Fe₃O₄ NPs and modifying them with 3-(N,N-diethylamino) propyltrimethoxysilane. Field-emission scanning electron microscopy, FTIR and zeta potential measurements were employed to characterize the modified NPs. They were then used as an adsorbent to remove acidic interferences (such as malic acid and succinic acid), which are major interferences in LC-MS/MS analysis in causing ion suppression in the MS spectra of pesticides. In addition, graphitized carbon black (GCB) was used as an adsorbent to eliminate interferences by pigments. The use of Fe₃O₄-PSA NPs can replace time-consuming centrifugation as used in the so-called QuEChERS (quick, easy, cheap, effective, rugged and safe) method. This improvement is particularly significant in high-throughput analysis. Following the optimization of the quantities of Fe₃O₄-PSA NPs and GCB, the method was applied to the determination of 56 pesticides in (spiked) fruits (apple, kiwi, orange and pear) by ultra-HPLC-MS/MS. The analytical ranges typically extend from 1 to 200 ng∙mL⁻¹, and recoveries range from 60.2 to 130 % at different concentrations of all four kinds of fruits. The LOQs for the pesticides are 10 ng∙kg⁻¹, which makes the method a viable tool for pesticide monitoring in fruits.

Magnetite nanoparticles modified with 3-(N,N-diethylamino) propyltrimethoxysilane (Fe₃O₄-PSA NPs) are shown to be useful materials for removal of acidid interferents from sample matrices. Their use can replace time-consuming centrifugation as used in the traditional QuEChERS method.