一种InP双异质结双极晶体管小信号物理模型及其提取方法

研究了InP双异质结双极晶体管（DHBT）的能带结构对集电极电容的影响,解决了传统方法不能准确提取InP DHBT集电极电容的问题.考虑了基极-发射极和集电极-发射极引线间的交叠电容,并从物理上区分了InP DHBT的本征电阻、外部电阻与寄生电阻,建立了一个基于物理的InP基DHBT小信号模型.同时提出了一套直接提取模型参数的方法,该方法无需引入数学优化,具有清晰的物理意义.提取的结果在很宽的偏置范围内准确地拟合了器件特性,验证了模型的准确性与提取方法的有效性. 关键词： InP双异质结双极晶体管 集电极电容 小信号模型 参数提取     

异质结界面电荷对突变InP/InGaAs异质结双极晶体管热场发射影响研究

异质结界面电荷的存在改变了异质结的内建势, 这引起了界面势垒尖峰高度和形状的扰动, 从而使异质结界面载流子的输运产生相应的变化, 最终导致异质结双极晶体管 (HBT) 性能的改变. 基于热场发射-扩散模型, 对异质结界面电荷对InP/InGaAs HBT性能的改变做了研究, 得到结论是正极性的界面电荷有利于InP/InGaAs HBT的直流和高频特性的改善, 而负极性的界面电荷则使器件的直流和高频特性变差. 关键词： InP/InGaAs异质结双极晶体管 界面电荷 内建势 热场发射     

An electromagnetic simulation assisted small signal modeling method for InP double-heterojunction bipolar transistors

We present a convenient and practical electromagnetic (EM) assisted small-signal model extraction method for InP double-heterojunction bipolar transistors (DHBTs). Parasitic parameters of pad and electrode fingers are extracted by means of 3D EM simulation. The simulations with a new excitation scheme are closer to the actual on-wafer measurement conditions. Appropriate simulation settings are calibrated by comparing measurement and simulation of OPEN and SHORT structures. A simpler $\pi $-type topology is proposed for the intrinsic model, in which the base-collector resistance $R_\mu$, output resistance $R_{\rm ce}$ are deleted, and a capacitance $C_{\rm ce}$ is introduced to characterize the capacitive parasitic caused by the collector finger and emitter ground bar. The intrinsic parameters are all extracted by exact equations that are derived from rigorous mathematics. The method is characterized by its ease of implementation and the explicit physical meaning of extraction procedure. Experimental validations are performed at four biases for three InGaAs/InP HBT devices with $0.8\times 7 $μm, 0$.8\times 10 $μm and $0.8\times 15 $μm emitter, and quite good fitting results are obtained in the range of 0.1-50 GHz.     

A G-band terahertz monolithic integrated amplifier in 0.5-μm InP double heterojunction bipolar transistor technology

Design and characterization of a G-band(140–220 GHz) terahertz monolithic integrated circuit(TMIC) amplifier in eight-stage common-emitter topology are performed based on the 0.5-μm In Ga As/In P double heterojunction bipolar transistor(DHBT). An inverted microstrip line is implemented to avoid a parasitic mode between the ground plane and the In P substrate. The on-wafer measurement results show that peak gains are 20 dB at 140 GHz and more than 15-dB gain at 140–190 GHz respectively. The saturation output powers are-2.688 dBm at 210 GHz and-2.88 dBm at 220 GHz,respectively. It is the first report on an amplifier operating at the G-band based on 0.5-μm InP DHBT technology. Compared with the hybrid integrated circuit of vacuum electronic devices, the monolithic integrated circuit has the advantage of reliability and consistency. This TMIC demonstrates the feasibility of the 0.5-μm InGaAs/InP DHBT amplifier in G-band frequencies applications.     

Extracting dark current components and characteristics parameters for InGaAs/InP avalanche photodiodes

The dark current of separate absorption grading charge multiplication (SAGCM) InGaAs/InP avalanche photodiodes has been numerical analyzed. SRH current, TAT current, BBT current and avalanche amplification combined together as the dark current have been extracted by simulation separately. The trend of punch-through voltage and breakdown voltage have been discussed, meanwhile the influence of structure parameters also has been investigated.     

Photon-counting laser ranging with InGaAs/InP avalanche photodiode in the passively quenched and 1-GHz sinusoidally gated

We experimentally studied photon-counting laser ranging at 1550 nm using InGaAs/InP avalanche photodiode based single-photon detectors (SPDs). The SPDs operated in the passive quenching and 1-GHz sinusoidal gating Geiger modes, corresponding to continuous and quasi-continuous photon-counting ranging, respectively. Despite that the passively quenched SPD provided relatively high effective detection efficiency, quasi-continuous photon-counting ranging excelled the continuous one with fast acquisition speed and improved depth resolution due to the short deadtime and low timing jitter of the SPD in 1-GHz sinusoidally gated mode.     

不同偏置影响锗硅异质结双极晶体管单粒子效应的三维数值仿真研究

针对国产锗硅异质结双极晶体管(SiGe HBT),采用半导体器件三维计算机模拟工具,建立单粒子效应三维损伤模型,研究不同偏置状态对SiGe HBT单粒子效应的影响.分析比较不同偏置下重离子入射器件后,各端口电流瞬变峰值和电荷收集量随时间的变化关系,获得SiGe HBT单粒子效应与偏置的响应关系.结果表明:不同端口对单粒子效应响应的最劣偏置不同,同一端口电荷收集量和瞬变电流峰值的最劣偏置也有所差异.载流子输运方式变化和外加电场影响是造成这种现象的主要原因.     

Extrinsic equivalent circuit modeling of InP HEMTs based on full-wave electromagnetic simulation

With the widespread utilization of indium-phosphide-based high-electron-mobility transistors (InP HEMTs) in the millimeter-wave (mmW) band, the distributed and high-frequency parasitic coupling behavior of the device is particularly prominent. We present an InP HEMT extrinsic parasitic equivalent circuit, in which the conductance between the device electrodes and a new gate-drain mutual inductance term L_mgd are taken into account for the high-frequency magnetic field coupling between device electrodes. Based on the suggested parasitic equivalent circuit, through HFSS and advanced design system (ADS) co-simulation, the equivalent circuit parameters are directly extracted in the multi-step system. The HFSS simulation prediction, measurement data, and modeled frequency response are compared with each other to verify the feasibility of the extraction method and the accuracy of the equivalent circuit. The proposed model demonstrates the distributed and radio-frequency behavior of the device and solves the problem that the equivalent circuit parameters of the conventional InP HEMTs device are limited by the device model and inaccurate at high frequencies when being extracted.     

Physical modeling of direct current and radio frequency characteristics for In P-based InAlAs/InGaAs HEMTs

Direct current(DC) and radio frequency(RF) performances of InP-based high electron mobility transistors(HEMTs)are investigated by Sentaurus TCAD. The physical models including hydrodynamic transport model, Shockley–Read–Hall recombination, Auger recombination, radiative recombination, density gradient model and high field-dependent mobility are used to characterize the devices. The simulated results and measured results about DC and RF performances are compared, showing that they are well matched. However, the slight differences in channel current and pinch-off voltage may be accounted for by the surface defects resulting from oxidized InAlAs material in the gate-recess region. Moreover,the simulated frequency characteristics can be extrapolated beyond the test equipment limitation of 40 GHz, which gives a more accurate maximum oscillation frequency( f_(max)) of 385 GHz.     

锗硅/硅异质结材料的化学气相淀积生长动力学模型

基于化学气相淀积(CVD)的Grove理论和Fick第一定律,提出并建立了锗硅(SiGe)/硅(Si)异质结材料减压化学气相淀积(RPCVD)生长动力学模型.与以前锗硅/硅异质结材料生长动力学模型仅考虑表面反应控制不同,本模型同时考虑了表面反应和气相传输两种控制机理,并给出了两种控制机理极限情况下的模型.本模型不仅适用于低温锗硅/硅应变异质结材料生长的表征,也适用于表征高温锗硅/硅弛豫异质结材料生长的表征.将模型计算值与实验结果进行了对比,无论是625℃低温下的应变SiGe的生长,还是900℃高温下的弛豫 关键词： SiGe/Si异质结材料 化学气相淀积生长动力学模型 Grove理论 Fick第一定律     

基于1/f噪声的NPN晶体管辐照感生电荷的定量分离

本文针对NPN双极性晶体管, 在研究辐照感生的氧化层电荷及界面态对晶体管基极电流和1/f噪声的影响的基础上, 建立辐照感生氧化层电荷及界面态与基极电流和1/f噪声的定量物理模型. 根据所建立的模型, 提出一种新的分离方法, 利用1/f噪声和表面电流求出氧化层电荷密度, 利用所求得氧化层电荷密度和表面电流求出界面态密度. 利用本方法初步实现了辐照感生氧化层电荷及界面态的定量计算.     

Effects of rapid thermal annealing on the energy levels of InAs/InP self-assembled quantum dots

We have studied the effects of thermal annealing on the electrical properties of InAs/InP self-assembled quantum dots (QDs) using deep level transient spectroscopy (DLTS). It was found from the DLTS measurements that the activation energy of the QD signal varied from 0.47 to 0.60 eV and the emission cross section changed from 1.01×10⁻¹⁵ to 9.63×10⁻¹⁴ cm² when the annealing temperature increased up to 700 °C. As a result of the thermal annealing process at the temperature ranging from 500 to 600 °C, the higher activation energy and the larger emission cross section of the QD related signal were observed for the annealed samples compared to those for the as-grown sample. On the basis of the capture barrier height for the QDs structure being lowered from 0.24 to 0.06 eV at the annealing temperature of 700 °C, thermal damage was considered as the reason. The appropriate annealing process can provide a clue for the engineering of the energy levels in the self-assembled QD structures.     

基于通用数据采集卡的水声应答器设计

水声应答器(Acoustic Transponder/Responder)是一类常用的水声设备,主要功能是完成水下设备的定位和导航,广泛应用在水声系统测试、目标模拟以及水声科学试验中。本文以NI公司的PCI-6052采集卡和工控机构成信号处理模块,设计出了一种可灵活配置的水声应答系统(ESRAE,Extensible Sound Responder for Acoustic Experiments),通过环境噪声电平的跟踪估计和脉冲判决技术实现了复杂海洋条件下脉冲检测、回发功能,并在海洋水声信道测量试验中得到了成功的应用。