Sonoluminescence characterization of inertial cavitation inside a BSA phantom treated by pulsed HIFU

The aim of this study was to investigate the inertial cavitation inside a phantom treated by pulsed HIFU (pHIFU). Basic bovine serum albumin (BSA) phantoms without any inherent ultrasound contrast agents (UCAs) or phase-shift nano-emulsions (PSNEs) were used. During the treatment, sonoluminescence (SL) recordings were performed to characterize the spatial distribution of inertial cavitation adjacent to the focal region. High-speed photographs and thermal coagulations, comparing with the SL results, were also recorded and presented. A series of pulse parameters (pulse duration (PD) was between 1 and 23 cycles and pulse repetition frequency (PRF) was between 0.5 kHz and 100 kHz) were performed to make a systematic investigation under certain acoustic power (APW). Continuous HIFU (cHIFU) investigation was also performed to serve as control group. It was found that, when APW was 19.5 W, pHIFU with short PD was much easier to form SL adjacent to the focal region inside the phantom, while it was difficult for cHIFU to generate cavitation bubbles. With appropriate PD and PRF, the residual bubbles of the previous pulses could be stimulated by the incident pulses to oscillate in a higher level and even violently collapse, resulting to enhanced physical thermogenesis. The experimental results showed that the most violent inertial cavitation occurs when PD was set to 6 cycles (5 μs) and PRF to 10 kHz, while the highest level of thermal coagulation was observed when PD was set to 10 cycles. The cavitational and thermal characteristics were in good correspondence, exhibiting significant potentiality regarding to inject-free cavitation bubble enhanced thermal ablation under lower APW, compared to the conventional thermotherapy.     

The pulsed microwave damage trend of a bipolar transistor as a function of pulse parameters

In the present paper we conduct a theoretical study of the thermal accumulation effect of a typical bipolar transistor caused by high power pulsed microwaves(HPMs),and investigate the thermal accumulation effect as a function of pulse repetition frequency(PRF) and duty cycle.A study of the damage mechanism of the device is carried out from the variation analysis of the distribution of the electric field and the current density.The result shows that the accumulation temperature increases with PRF increasing and the threshold for the transistor is about 2 kHz.The response of the peak temperature induced by the injected single pulses indicates that the falling time is much longer than the rising time.Adopting the fitting method,the relationship between the peak temperature and the time during the rising edge and that between the peak temperature and the time during the falling edge are obtained.Moreover,the accumulation temperature decreases with duty cycle increasing for a certain mean power.     

Pulsed microwave damage trend of bipolar transistor as a function of pulse parameters

In the present paper we conduct a theoretical study of the thermal accumulation effect of a typical bipolar transistor caused by high power pulsed microwave (HPM), and investigate the thermal accumulation effect as a function of pulse repetition frequency (PRF) and duty cycle. A study of the damage mechanism of the device is carried out from the variation analysis of the distribution of the electric field and the current density. The result shows that the accumulation temperature increases with PRF increasing and the threshold for the transistor is about 2 kHz. The response of the peak temperature induced by the injected single pulses indicates that the falling time is much longer than the rising time. Adopting the fitting method, the relationship between the peak temperature and the time during the rising edge and that between the peak temperature and the time during the falling edge are obtained. Moreover, the accumulation temperature decreases with duty cycle increasing for a certain mean power.     

基于电阻抗层析成像的高强度聚焦超声温度监测技术

作为一种对正常组织无损伤且不易引起癌细胞转移的非入侵肿瘤治疗手段,高强度聚焦超声(HIFU)治疗过程中焦域的温度监测是实现剂量精准控制的关键.本文基于生物组织的温度-电阻抗的关系,将电阻抗层析成像(EIT)和HIFU治疗相结合,提出了一种利用组织焦平面的表面电压实现电阻抗重构的检测技术.建立了HIFU治疗和EIT综合系统模型,在考虑组织的声吸收条件下,对三维Helmholtz方程在柱坐标下的声场计算进行了二维简化,并引入Pennes生物热传导方程来计算HIFU焦域的声压和温升分布特性;引入生物组织的温度-电阻抗关系,基于麦克斯韦电磁场理论,建立了具有温度分布HIFU焦域的电流和电压计算模型,利用恒流注入的边界条件实现电场计算,获得焦平面的表面电压分布.在数值计算中,利用实验聚焦换能器参数,模拟了在固定声功率下组织焦域的声场和温度场分布,以及中心和偏心聚焦条件下不同治疗时刻的电导率分布;然后通过对称电极的循环电流注入,计算了组织模型焦平面内的电流密度和电势分布,获得了焦平面圆周分布的表面电极电压;进一步采用修正的牛顿-拉夫逊算法,利用32×32的表面电极电压实现了焦平面内电导率分布的重建.结果表明,基于温度-电阻抗关系的EIT电导率重建技术不但能准确定位HIFU焦域中心,还能恢复HIFU治疗中焦域的温度分布,证明了EIT用于HIFU治疗中温度监测的可行性,为其疗效评估和剂量控制提供了一种无创电阻抗测量和成像新方法.     

利用傅里叶变换红外光谱分析高温对木材-胶粘剂界面性能的影响

胶合木层板间界面起传递应力的作用,是构件承载的重要参数,其高温胶合性能决定了构件的抗火性能。以兴安落叶松结构材,以及结构用间苯二酚-酚醛树脂胶粘剂(PRF)和三聚氰胺-脲醛树脂胶粘剂(MUF)为研究对象,研究了20～280 ℃中木材含水率、密度、顺纹弦向抗剪强度和木材-胶粘剂界面胶合性能等216个试件在高温中的物理力学性能变化规律,通过傅里叶变换红外光谱分析高温中胶粘剂官能团变化,揭示了高温对木材-胶粘剂界面性能的劣化机理。结果表明,20～150 ℃时,兴安落叶松主要发生由水分释放导致的木材密度降低等物理反应,木材颜色未发生明显变化;150～200 ℃时,木材热降解开始,密度下降速度变缓,木材颜色逐渐加深;温度继续升高时,木材热降解加剧,颜色急剧加深,木材密度损失快速增加;当温度升至280 ℃时,木材发生炭化、完全转化为黑色,密度降至常温的72.49%。高温对兴安落叶松顺纹弦向抗剪强度有明显的劣化作用;20 ℃时木材抗剪强度为9.654 MPa,20～110 ℃时木材抗剪强度下降较快,150 ℃时降至常温的60.68%;150～280 ℃时,木材顺纹抗剪强度急剧下降,280 ℃时降至1.054 MPa。木材-胶粘剂界面的高温性能与胶粘剂的耐热性能密切相关;常温时,兴安落叶松与PRF和MUF均有较好的胶合性能,其界面抗剪强度分别为9.071和9.619 MPa,木破率均在80%以上;随着温度的升高,两种胶粘剂的界面抗剪强度均明显降低,木材-PRF界面较木材-MUF具有更好的耐高温性能。20～150 ℃时,两种胶粘剂界面抗剪强度劣化规律与木材抗剪强度相似,150 ℃时木材-PRF和木材-MUF的界面抗剪强度分别为常温的60.61%和60.92%,木破率均高于70%。150～280 ℃时,木材-PRF界面抗剪强度劣化规律仍与木材顺纹抗剪强度相似,280 ℃时降至0.774 MPa;木材-MUF界面胶合性能受温度影响更大,220 ℃时其木破率为10%,280 ℃时界面抗剪强度降至0 MPa。傅里叶变换红外光谱图中,20～150 ℃时PRF化学结构无明显变化;温度高于150 ℃时主要发生胶粘剂的进一步交联,以及醚键和亚甲基桥的断裂,PRF开始热解,但化学结构仍较完整;20～150 ℃时MUF的化学结构无明显变化,温度高于200 ℃时,羟甲基特征峰减弱、异氰酸酯基团产生,热降解剧烈,PRF较MUF具有更高的耐热性能。研究结果将为木结构工程合理选择原材料提供数据支撑,并为完善木结构抗火设计理论和方法提供依据。     

Sonochemiluminescence observation and acoustic detection of cavitation induced by pulsed HIFU at a tissue–fluid interface

The aim of this study is to investigate the mechanism of the erosion process induced by 1.2 MHz pulsed high-intensity focused ultrasound (pulsed HIFU). By using Sonochemiluminescence (SCL) photograph, the initiation and maintenance of active cavitation were observed. In order to understand the role of both inertial cavitation and stable cavitation, a passive cavitation detection (PCD) transducer was used. Since the exposure variables of HIFU are important in the controlled ultrasound tissue erosion, the influence of pulse length (PL) and duty cycle (DC, T_on:T_off) has been examined. The results of tissue hole, SCL observation and acoustic detection revealed that the erosion was highly efficient for shorter PL. For higher DCs, the area of SCL increased with increasing PL. For lower DCs, the area of SCL increased with increasing PL from 10 to 20 μs and then kept constant. For all PLs, the intensity of SCL decreased with lower DC. For all DCs, the intensity of SCL per unit area (the ratio of SCL intensity to SCL area) also decreased with increasing PL from 10 to 80 μs, which suggested that the higher the intensity of SCL is, the higher the efficiency of tissue erosion is. At DC of 1:10, the position of the maximum pixel in SCL pictures was distant from the tissue–fluid interface with the increasing PL because of shielding effect. By the comparison of inertial cavitation dose (ICD) and the stable cavitation dose (SCD), the mechanisms associated with inertial cavitation are very likely to be the key factor of the erosion process.     

Effect of the duty ratio on the indium tin oxide (ITO) film deposited by in-line pulsed DC magnetron sputtering method for resistive touch panel

The indium tin oxide (ITO) film was deposited on PET (polyethylene terephthalate) film using in-line pulsed DC magnetron sputtering system with different duty ratios. The reverse time and the frequency of pulsed DC power were changed to obtain the different duty ratios. From the electrical and optical properties such as the sheet resistance, resistivity, thickness and transmittance, the pulsed DC sputtered ITO/PET films were also superior to the DC sputtered ITO/PET films. The reverse time had little effect on the properties of the ITO/PET film and the frequency of pulsed DC power had an immerse effect on the properties of the ITO/PET films. The optimal ITO/PET film was obtained when the frequency was 200 kHz, the reverse time was 1 μs, and the duty ratio was about 80%.     

半导体泵浦铷蒸气激光器国内首次出光北大核心CSCD

采用体光栅对商用线阵半导体激光器进行线宽压缩,得到线宽0.1nm、中心波长780.2nm、最高连续输出功率80W的泵浦激光输出。为了降低热效应,通过外加斩波器将泵浦光转化为脉冲模式,脉宽440μs,占空比为1∶5。采用长度为5mm的铷金属饱和蒸气作为增益介质,并在常温下充入33kPa乙烷和47kPa氦气,进行了出光实验。在泵浦峰值功率35.4W,铷吸收池温度120℃时,得到峰值功率600mW的795nm铷激光输出,斜率效率为1.7%。     

Volume transfer constant (K) maps from dynamic contrast enhanced MRI as potential guidance for MR-guided high intensity focused ultrasound treatment of hypervascular uterine fibroids

Higher perfusion of uterine fibroids at baseline is recognized as cause for poor efficacy of MR-guided high intensity focused ultrasound (HIFU) ablation, and higher acoustic power has been suggested for the treatment of high-perfused areas inside uterine fibroids. However, considering the heterogeneously vascular distribution inside the uterine fibroids especially with hyper vascularity, it is not easy to choose the correct therapy acoustic power for every part inside fibroids. In our study, we presented two cases of fibroids with hyper vascularity, to show the differences between them with different outcomes. Selecting higher therapy acoustic powers to ablate high-perfused areas efficiently inside fibroids might help achieving good ablation results. Volume transfer constant (K^trans) maps from dynamic contrast-enhanced (DCE) imaging at baseline helps visualizing perfusion state inside the fibroids and locating areas with higher-perfusion. In addition, with the help of K^trans maps, appropriate therapy acoustic power could be selected by the result of initial test and therapy sonications at different areas with significantly different perfusion state inside fibroids.     

高强度聚焦超声用于肿瘤治疗的研究

高强度聚焦超声（ＨＩＦＵ）能在短时间内使病变组织的温度升至７０℃以上,导致病变组织凝固坏死,是一种具有巨大潜力的、非侵入的、有效的肿瘤治疗手段。本文对ＨＩＦＵ的动物试验、临床应用及治疗装置的研究情况进行了总结,分析了该技术尚存在的问题,最后展望了其应用前景。     

Influence of dynamic tissue properties on temperature elevation and lesions during HIFU scanning therapy: Numerical simulation

When large tumors are treated,ablation of the entire volume of tumors requires multiple treatment spots formed by high intensity-focused ultrasound(HIFU)scanning therapy.The heating effect of HIFU on biological tissue is mainly reflected in temperature elevation and tissue lesions.Tissue property parameters vary with temperature and,in turn,the distribution of temperature as well as the heating effects change accordingly.In this study,an HIFU scanning therapy model considering dynamic tissue properties is provided.The acoustic fields and temperature fields are solved combining the Helmholtz wave equation with Pennes bio-heat transfer equation based on the finite element method(FEM)to investigate the effects of various tissue properties(i.e.,the attenuation coefficient,acoustic velocity,thermal conductivity,specific heat capacity,density,and blood perfusion rate)on heating performance.Comparisons of the temperature distribution and thermal lesions under static and dynamic properties are made based on the data of tissue property parameters varying with temperature.The results show that the dynamic changes of thermal conductivity,specific heat capacity,and acoustic velocity may account for the decrease of temperature elevation in HIFU treatment,while the dynamic changes of attenuation coefficient,density,and blood perfusion rate aggravate the increase of temperature on treatment spots.Compared with other properties,the dynamic change of attenuation coefficient has a greater impact on tissue temperature elevation.During HIFU scanning therapy,the temperature elevation and tissue lesions of the first treatment spot are smaller than those of the subsequent treatment spots,but the temperature on the last treatment spot drops faster during the cooling period.The ellipsoidal tissue lesion is not symmetrical;specifically,the part facing toward the previous treatment spot tends to be larger.Under the condition of the same doses,the temperature elevation and the size of tissue lesions under dynamic properties present significant growth in comparison to static properties.Besides,the tissue lesion begins to form earlier with a more unsymmetrical shape and is connected to the tissue lesion around the previous treatment spot.As a result,lesions around all the treatment spots are connected with each other to form a closed lesion region.The findings in this study reveal the influence of dynamic tissue properties on temperature elevation and lesions during HIFU scanning therapy,providing useful support for the optimization of treatment programs to guarantee higher efficacy and safety.     

Effects of pulsed bias duty ratio on microstructure and mechanical properties of TiN/TiAlN multilayer coatings

TiN/TiAlN multilayer coatings were deposited on M2 high speed steel by a pulsed bias arc ion plating system. The effect of pulsed bias duty ratio on the microstructure, mechanical and wear properties was investigated. The amount of macroparticles reduced with the increase of the duty ratio. The surface roughness was 0.0858 μm at duty ratio of 50%. TiN/TiAlN multilayer coatings were crystallized with orientations in the (1 1 1), (2 0 0) (2 2 2) and (3 1 1) crystallographic planes and the microstructure strengthened at (1 1 1) preferred orientation. At duty ratio of 20%, the hardness of TiN/TiAlN multilayer coatings reached a maximum of 3004 HV, which was 3.2 times that of the substrate. The adhesion strength reached a maximum of 77 N at 50% duty ratio. Friction and wear analyses were carried out by pin-on-disc tester at room temperature. Compared with the substrate, all the specimens coated with TiN/TiAlN multilayer coatings exhibited better tribological properties.     

Spatial and temporal observation of phase-shift nano-emulsions assisted cavitation and ablation during focused ultrasound exposure

Background: Phase-shift nano-emulsions (PSNEs) with a small initial diameter in nanoscale have the potential to leak out of the blood vessels and to accumulate at the target point of tissue. At desired location, PSNEs can undergo acoustic droplet vaporization (ADV) process, change into gas bubbles and enhance focused ultrasound efficiency. The threshold of droplet vaporization and influence of acoustic parameters have always been research hotspots in order to spatially control the potential of bioeffects and optimize experimental conditions. However, when the pressure is much higher than PSNEs’ vaporization threshold, there were little reports on their cavitation and thermal effects.Object: In this study, PSNEs induced cavitation and ablation effects during pulsed high-intensity focused ultrasound (HIFU) exposure were investigated, including the spatial and temporal information and the influence of acoustic parameters.Methods: Two kinds of tissue-mimicking phantoms with uniform PSNEs were prepared because of their optical transparency. The Sonoluminescence (SL) method was employed to visualize the cavitation activities. And the ablation process was observed as the heat deposition could produce white lesion.Results: Precisely controlled HIFU cavitation and ablation can be realized at a relatively low input power. But when the input power was high, PSNEs can accelerate cavitation and ablation in pre-focal region. The cavitation happened layer by layer advancing the transducer. While the lesion appeared to be separated into two parts, one in pre-focal region stemmed from one point and grew quickly, the other in focal region grew much more slowly. The influence of duty cycle has also been examined. Longer pulse off time would cause heat transfer to the surrounding media, and generate smaller lesion. On the other hand, this would give outer layer bubbles enough time to dissolve, and inner bubbles can undergo violent collapse and emit bright light.     

Study of a peak in cavitation activity from HIFU exposures using TA fluorescence

Methods of measuring the sound field and focal region of a 1.05 MHz high intensity focused ultrasound (HIFU) are described in this paper. 1.05 MHz pulsed HIFU with intensity 2400 W/cm(2) with a 1:1 duty cycle ("on" phase equaled "off" phase) was used to irradiate terephthalic acid (TA). Pulse periods of 0.5 ms, 1 ms, 3.3 ms, 10 ms, 15 ms, 33 ms, 0.1s and 1s were used. The irradiation time was 2 min. To indicate the intensity of inertial cavitation activity, the fluorescence intensity of hydroxyterephthalic acid (HTA) was measured. The result shows that the cavitation activity of pulsed HIFU peaks at a pulse period of 10 ms, cavitation activity is significantly greater for pulse periods from 2 to 20 ms than for others.     

连续和重复频率激光对旋转壳体加热效率的数值模拟

 基于有效利用激光能量的目的,采用有限元分析方法分析并比较了重复频率和连续激光对旋转壳体的加热效率。数值计算结果表明：重复频率激光要比连续激光的加热效率高,而且加热效率与重复频率、占空比等有关;在平均功率密度相同的前提下,在频率相同条件下,占空比减小,温度上升加快,即加热效率随占空比的减小而增大;在相同占空比条件下,重复频率越小温度周期变化越明显,振荡峰值越大,当占空比较小时随着辐照时间的增加重复频率对加热效率影响减小。     

An in vitro feasibility study of controlled drug release from encapsulated nanometer liposomes using high intensity focused ultrasound

A liposome with a diameter ranging from 150 to 200 nm has been considered to be one of the optimal vehicles for targeted drug delivery in vivo since it is able to encapsulate drug and also circulate in the blood stream stably. Its small size, however, makes controlled release of its encapsulated content difficult. A feasibility study for applications of high intensity focused ultrasound (HIFU) of the mega-hertz frequency to induce controlled release of its content was carried out. This study, using the dynamic light scattering and transmission electron microscopic observation, demonstrated 21.2% of encapsulated fluorescent materials (FITC) could be released from liposomes with an average diameter of 210 nm when exposed to continuous (cw) ultrasound at 1.1 MHz (I_SPTA = 900 W/cm²) for 10 s and the percentage release efficiency can reach to 70% after 60 s irradiation. This result also reveals that rupture of relatively large liposomes (>100 nm) and generation of pore-like defects in the membrane of small liposomes (<100 nm) due to HIFU excitation might be the main causes of the release; the inertial cavitation took place during the irradiation. The controlled drug release from liposomes by HIFU may be proven to be a potential useful modality for clinical applications.     

Beam localization in HIFU temperature measurements using thermocouples, with application to cooling by large blood vessels

Experimental studies of thermal effects in high-intensity focused ultrasound (HIFU) procedures are often performed with the aid of fine wire thermocouples positioned within tissue phantoms. Thermocouple measurements are subject to several types of error which must be accounted for before reliable inferences can be made on the basis of the measurements. Thermocouple artifact due to viscous heating is one source of error. A second is the uncertainty regarding the position of the beam relative to the target location or the thermocouple junction, due to the error in positioning the beam at the junction. This paper presents a method for determining the location of the beam relative to a fixed pair of thermocouples. The localization technique reduces the uncertainty introduced by positioning errors associated with very narrow HIFU beams. The technique is presented in the context of an investigation into the effect of blood flow through large vessels on the efficacy of HIFU procedures targeted near the vessel. Application of the beam localization method allowed conclusions regarding the effects of blood flow to be drawn from previously inconclusive (because of localization uncertainties) data. Comparison of the position-adjusted transient temperature profiles for flow rates of 0 and 400 ml/min showed that blood flow can reduce temperature elevations by more than 10%, when the HIFU focus is within a 2 mm distance from the vessel wall. At acoustic power levels of 17.3 and 24.8 W there is a 20- to 70-fold decrease in thermal dose due to the convective cooling effect of blood flow, implying a shrinkage in lesion size. The beam-localization technique also revealed the level of thermocouple artifact as a function of sonication time, providing investigators with an indication of the quality of thermocouple data for a given exposure time. The maximum artifact was found to be double the measured temperature rise, during initial few seconds of sonication.     

Development of copper bromide laser master oscillator power amplifier system

Development of master oscillator power amplifier (MOPA) system of copper bromide laser (CBL) operating at 110 W average power is reported. The spectral distribution of power at green (510.6 nm) and yellow (578.2 nm) components in the output of a copper bromide laser is studied as a function of operating parameters. The electrical input power was varied from 2.6 to 4.3 kW, the pulse repetition frequency (PRF) was changed from 16 to 19 kHz, and the pressure of the buffer gas (neon) was kept fixed at 20 mbar. When the electrical input power was increased to 4.3 kW from 2.6 kW, the tube-wall temperature also increased to 488°C from 426°C but the ratio of the green to yellow power decreased to 1.53 from 3.73. The ratio of green to yellow power decreased to 1.53 from 1.63 when the PRF of the laser was increased to 19 kHz from 16 kHz. These observations are explained in terms of electron temperature, energy levels of transitions, and voltage and current waveforms across the laser head.     

High intensity focused ultrasound-induced gene activation in sublethally injured tumor cells in vitro

Cultured human cervical cancer (HeLa) and rat mammary carcinoma (R3230Ac) cells were transfected with vectors encoding green fluorescent protein (GFP) under the control of hsp70B promoter. Aliquots of 10-microl transfected cells (5 x 10(7) cells/ml) were placed in 0.2-ml thin-wall polymerase chain reaction tubes and exposed to 1.1-MHz high intensity focused ultrasound (HIFU) at a peak negative pressure P- = 2.68 MPa. By adjusting the duty cycle of the HIFU transducer, the cell suspensions were heated to a peak temperature from 50 to 70 degrees C in 1-10 s. Exposure dependent cell viability and gene activation were evaluated. For a 5-s HIFU exposure, cell viability dropped from 95% at 50 degrees C to 13% at 70 degrees C. Concomitantly, gene activation in sublethally injured tumor cells increased from 4% at 50 degrees C to 41% at 70 degrees C. A similar trend was observed at 60 degrees C peak temperature as the exposure time increased from 1 to 5 s. Further increase of exposure duration to 10 s led to significantly reduced cell viability and lower overall gene activation in exposed cells. Altogether, maximum HIFU-induced gene activation was achieved at 60 degrees C in 5 s. Under these experimental conditions, HIFU-induced gene activation was found to be produced primarily by thermal rather than mechanical stresses.     

退火处理Fe43Co43Hf7B6Cu1非晶合金的正电子湮没研究

对熔体急冷法制备的Fe₄₃Co₄₃Hf₇B₆Cu₁非晶合金进行了200,300,400和500 ℃保温30 min的退火处理,用正电子湮没寿命谱、X射线衍射、穆斯堡尔谱等方法研究了退火后试样的结构及结构缺陷变化.结果表明,在非晶合金的制备态,正电子主要在非晶基体相空位尺寸的自由体积中湮没,湮没寿命τ₁为158.4 ps,强度I₁关键词： 43Co₄₃Hf₇B₆Cu₁非晶')" href="#">Fe₄₃Co₄₃Hf₇B₆Cu₁非晶 退火处理 正电子湮没寿命 结构与结构缺陷