Drop‐coating deposition Raman spectroscopy of liposomes

Drop‐coating deposition Raman (DCDR) spectroscopy was tested as a potential technique for studying liposomes at very low sample concentrations. We used model liposomes prepared either from 1,2‐distearoyl‐sn‐glycero‐3‐phospocholine or from soybean asolectin, which is composed of various lipids and thus represents a good model of natural membranes. In both cases, deposited samples formed a dried drop with a circular shape with a ring of concentrated liposomes at the edge. Spectral mapping showed that maximum Raman intensity originated from the inner part of the edge ring, while Raman signal gradually decreased in both radial directions. The Raman spectra exhibited excellent reproducibility of spectral characteristics at different locations in the drop, indicating similar conformation and ordering of hydrocarbon lipid chains in the sample. Our results suggest that DCDR spectroscopy can be used for studying lipids in situ, and sensitivity of this technique is at least two orders of magnitude higher than that of conventional Raman microscopy. Copyright © 2011 John Wiley & Sons, Ltd.     

Drop‐coating deposition Raman spectroscopy of porphyrins

We report an improvement of the Raman detection sensitivity of porphyrins by factor of 10⁵ using drop‐coating deposition Raman spectroscopy (DCDR). We were able to obtain Raman spectra from ~20 nM initial (deposited) concentrations of cationic and anionic porphyrin. This detection limit is comparable with or even better than that of surface‐enhanced Raman scattering spectroscopy using Ag nanoparticles. Moreover, DCDR spectrum of protoporphyrin IX, which is known as a marker in clinical diagnostics of cancer, was also obtained from 10 nM deposited concentration. To our knowledge, it is the first demonstration of the resonance DCDR spectroscopy. Copyright © 2015 John Wiley & Sons, Ltd.     

Detection of biologically active diterpenoic acids by Raman Spectroscopy

Three poorly detectable, biologically active diterpenoic acids, kaurenoic, abietic, and gibberellic acid, were studied by using different modes of Raman spectroscopy. Because of their structural similarities, in the absence of strongly polarizable groups, conventional Raman spectroscopy is not suitable for their unambiguous identification, especially not in solution. We attempted to increase the sensitivity by applying UV‐resonance Raman spectroscopy and surface‐enhanced Raman spectroscopy (SERS) techniques. The UV‐Raman spectra of the three compounds in ethanol/water 50:50 showed only very few enhanced Raman lines. SERS spectra with 514‐nm excitation with Ag colloids were also relatively weak. The best SERS spectra were obtained with 785‐nm excitation on a novel nanostructured substrate, ‘black silicon’ coated with a 400‐nm gold layer. The spectra showed clear differences, and these ‘fingerprints’ would be suitable for the unambiguous identification of these diterpenoic acids. Copyright © 2009 John Wiley & Sons, Ltd.     

Investigation into the protein composition of human tear fluid using centrifugal filters and drop coating deposition Raman spectroscopy

Drop coating deposition Raman spectroscopy (DCDRS) is a simple method of analysing weak protein solutions. This study is another step in evaluating the analysis of tear fluid by DCDRS as a future medical diagnostic technique. The main aims of this study are to determine whether the DCDR spectra from tear samples contain signals from more than one protein (so relative levels can be measured) and, if so, are the proteins homogeneously distributed in the dried ring of the deposited material. Tear samples were collected from four healthy volunteers and pooled prior to analysis. Proteins were separated by mass into three groups using centrifugal filters. These groups contained proteins with (1) masses greater than 100 kDa, (2) masses between 100 and 50 kDa and (3) masses between 50 and 3 kDa. DCDR spectra from each of these protein group solutions displayed significant differences, confirming that the mass separation had been successful. When used as basis vectors for least‐squares fitting, these spectra (and that of urea) produced excellent fits to the normal tear spectra. Least‐squares fitting of spectra from the same point on a single sample and from several drops of the same sample showed that the tear DCDR spectra were highly reproducible. Raman point mapping of the tear ring showed significant radial ring variation, especially towards the outer edge of the ring. The specific peak changes in the protein signal across the ring suggested that the difference in the outer edge was due to protein desiccation as opposed to inhomogeneous protein deposition. Copyright © 2008 John Wiley & Sons, Ltd.     

Uric acid detection by means of SERS spectroscopy on dried Ag colloidal drops

Uric acid concentration in human bodily fluids is an important marker for disorders such as gout, pre‐eclamsia or cardiovascular disease. However, currently used methods for its detection either lack sensitivity or require sophisticated, bulky and expensive equipment. In this work, we show that by using surface‐enhanced Raman scattering spectroscopy (SERS) on dried Ag colloidal drops and with 1064 nm excitation, concentrations of uric acid in aqueous solutions down to 10⁻⁶ M can be detected. Such sensitivity is sufficient for medical applications as concentration of uric acid in various bodily fluids are in the range of 10⁻³–10⁻⁴ M. Drying of the colloidal drops is known to result in the formation of ‘coffee‐ring’ structures that allow obtaining high enhancements but poor reproducibility. Here, the formation of the structures was avoided by choosing aluminum oxide as a base substrate and by controlling environment conditions. Despite the fact that variations of signal enhancement from sample to sample prevent quantitative analysis from being performed, the results of this work imply that strict control of sample preparation conditions could lead to obtaining reproducible SERS enhancements. Results of density functional theory calculations of uric acid tautomer – five‐atom silver cluster complexes performed for the first time show that the differences between Raman and SERS spectra of uric acid can be mainly explained by tautomerization of the molecule and its bonding to the silver surface. Assignment of spectral bands is important for correct SERS signal interpretation and detection of uric acid in biological fluids in the future studies. Copyright © 2016 John Wiley & Sons, Ltd.     

A facile method for the synthesis of large‐size Ag nanoparticles as efficient SERS substrates

Silver nanoparticles (Ag NPs) enjoy a reputation as an ultrasensitive substrate for surface‐enhanced Raman spectroscopy (SERS). However, large‐scale synthesis of Ag NPs in a controlled manner is a challenging task for a long period of time. Here, we reported a simple seed‐mediated method to synthesize Ag NPs with controllable sizes from 50 to 300 nm, which were characterized by scanning electron microscopy (SEM) and UV–Vis spectroscopy. SERS spectra of Rhodamine 6G (R6G) from the as‐prepared Ag NPs substrates indicate that the enhancement capability of Ag NPs varies with different excitation wavelengths. The Ag NPs with average sizes of ~150, ~175, and ~225 nm show the highest SERS activities for 532, 633, and 785‐nm excitation, respectively. Significantly, 150‐nm Ag NPs exhibit an enhancement factor exceeding 10⁸ for pyridine (Py) molecules in electrochemical SERS (EC‐SERS) measurements. Furthermore, finite‐difference time‐domain (FDTD) calculation is employed to explain the size‐dependent SERS activity. Finally, the potential of the as‐prepared SERS substrates is demonstrated with the detection of malachite green. Copyright © 2016 John Wiley & Sons, Ltd.     

Silver‐decorated carbon nanotube networks as SERS substrates

We report on investigations upon a surface‐enhanced Raman scattering (SERS) substrate produced from a two‐dimensional single‐walled carbon nanotube (SWNT) network decorated with Ag nanoparticles. Using the strong and unique Raman spectrum of SWNTs as a reference, the SWNT/Ag nanostructure can be considered to provide two regions: one with an ultrasensitive SERS response for single‐molecule SERS (SMSERS) study; and another with uniform SERS enhancement over an area of several square millimeters for general SERS measurements. We report the appearance of an anomalous Raman feature at around 2180 cm⁻¹ in the high‐sensitivity region which exhibits the characteristics of SMSERS. The SERS performance of the uniform area was characterized using pyridine vapor adsorbed onto the substrate. The presence of the SWNT/Ag nanostructure enhanced the Raman intensity by over seven orders of magnitude, a factor comparable to or exceeding that obtained on SERS substrates reported by other groups. The results indicate great potential to produce highly sensitive, uniform SERS substrates via further fine‐tuning of the nanostructure. Copyright © 2011 John Wiley & Sons, Ltd.     

Raman scattering of L‐tryptophan enhanced by surface plasmon of silver nanoparticles: vibrational assignment and structural determination

Vibrational bands of L ‐tryptophan which was adsorbed on Ag nanoparticles (∼10 nm in diameter) have been investigated in the spectral range of 200–1700 cm⁻¹ using surface‐enhanced Raman scattering (SERS) spectroscopy. Compared with the normal Raman scattering (NRS) of L ‐tryptophan in either 0.5 M aqueous solution (NRS‐AS) or solid powder (NRS‐SP), the intensified signals by SERS have made the SERS investigation at a lower molecular concentration (5 × 10⁻⁴ M ) possible. Ab initio calculations at the B3LYP/6‐311G level have been carried out to predict the optimal structure and vibrational wavenumbers for the zwitterionic form of L ‐tryptophan. Facilitated with the theoretical prediction, the observed vibrational modes of L ‐tryptophan in the NRS‐AS, NRS‐SP, and SERS spectra have been analyzed. In the spectroscopic observations, there are no significant changes for the vibrational bands of the indole ring in either NRS‐AS, NRS‐SP, or SERS. In contrast, spectral intensities involving the vibrations of carboxylate and amino groups are weak in NRS‐AS and NRS‐SP, but strong in SERS. The intensity enhancement in the SERS spectrum can reach 10³–10⁴‐fold magnification. On the basis of spectroscopic analysis, the carboxylate and amino groups of L ‐tryptophan are determined to be the preferential terminal groups to attach onto the surfaces of Ag nanoparticles in the SERS measurement. Copyright © 2008 John Wiley & Sons, Ltd.     

Preparation of SERS active Ag nanoparticles encapsulated by phospholipids

A cost‐effective way of fabricating lipid‐coated surface‐enhanced Raman spectroscopy (SERS) substrate having reproducible high SERS activity was proposed. Ag nanoparticle embedded in 1,2‐dioleoyl‐sn‐glycero‐3‐phosphocholine (DOPC) and 1,2‐dioleoyl‐3‐trimethylammonium‐propane (DOTAP) membranes was produced by direct deposition of a 5‐nm‐thick layer of Ag onto the solid‐supported phospholipid membrane, and subsequent dissolution of the Ag nanoparticle‐embedded membrane in iso‐octane allowed easy one‐pot fabrication of DOPC‐ or DOTAP‐coated Ag nanoparticles. In particular, DOTAP produced nearly monodisperse lipid‐encapsulated Ag nanoparticles (9 nm in diameter) exhibiting reproducible high SERS activity (detecting up to 10 nM of rhodamine 6G and 0.5 μM of glutathione). In addition, the process was modified to incorporate variety of Raman active molecules (rhodamine 6G, malachite green, 4‐aminothiopheonol, 4‐mercaptopyridine) into the particle‐encapsulating lipid bilayer. The DOTAP/Raman dye‐coated Ag nanoparticles also generated high SERS activity to enable potential application of the DOTAP/Raman dye‐coated Ag nanoparticles feasible in different areas. Copyright © 2014 John Wiley & Sons, Ltd.     

Identification of berberine in ancient and historical textiles by surface‐enhanced Raman scattering

The highly fluorescent natural dye berberine can be easily identified in microscopic textile samples by surface‐enhanced Raman spectroscopy employing citrate‐reduced Ag colloid. The ordinary Raman (OR) and SERS spectra of berberine are presented and discussed in the light of a DFT calculation. Using FT‐Raman and FT‐SERS we could reliably compare relative intensity shifts and investigate the adsorption geometry of berberine on Ag nanoparticles. The significant enhancement in the FT‐SERS spectrum of the out‐of‐plane ring system bending deformation mode at 729 cm⁻¹ relative to a group of in‐plane vibrations at around 1500 cm⁻¹ was interpreted as evidence of a ‘flat‐on’ adsorption geometry. SERS was successfully used to identify berberine in silk fiber samples coated with colloidal Ag following a pretreatment with HCl vapor. The SERS method allowed us to detect berberine in a microscopic sample of a single silk fiber from a severely degraded and soiled 17th Century Chinese textile fragment. Copyright © 2007 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman spectra of the neonicotinoid pesticide thiacloprid

Thiacloprid is a widely used pesticide belonging to the neonicotinoid class, which is characterized by a selective activity against insects and a reduced acute toxicity for humans. The importance of the environmental impact of neonicotinoids is being intensively researched, in order to evaluate the danger they pose for useful insects. Physical methods which allow the characterization of neonicotinoids in diluted aqueous solutions are therefore desirable. We present a study of Raman and surface‐enhanced Raman scattering (SERS) spectroscopy on thiacloprid in solid state, in acetone solution, and adsorbed onto silver and gold hydrosols at μM concentration. Density functional theory calculations allow the individualization of the most stable molecular structure, both in gas phase and in solution, and of the corresponding Raman spectra. The vibrational assignments lead to an interpretation of the differences between SERS and ordinary Raman spectra based on the possible interactions between the molecule and the metal surface, the main one involving the iminocyano group. Formation of a charge‐transfer complex is suggested by the dependence of the SERS spectra on the laser excitation wavelength. We evaluate the applicability of SERS spectroscopy to the chemical analysis of thiacloprid comparing SERS with current analytical methods. Copyright © 2013 John Wiley & Sons, Ltd.     

Stilbazolium merocyanine dye determination in different solutions,concentrations and colloids using SERS

Surface‐enhanced Raman scattering (SERS) measurements were carried out on stilbazolium merocyanine dye in methanol and pyridine solvents. Both solutions were measured in a series of concentrations covering a range of 5 × 10⁻⁵ M to 5 × 10⁻⁸ M . In these measurements, Ag and Au colloids were used, and the results have shown that Ag colloids yield better enhancement in the Raman spectra of this dye. Moreover, the effect of adding NaCl solution to the SERS samples was also studied. All measurements were carried out using the state‐of‐the‐art ChiralRaman instrument, which utilizes a 532 nm laser source. We report here on the success of using SERS to obtain Raman spectra of merocyanine dye at very low concentrations in an attempt to find a new approach that can be used for further investigations of the dye. The SERS spectra are reported here, and the results from different solutions, colloids, concentrations and pH values are compared. Copyright © 2006 John Wiley & Sons, Ltd.     

Potential‐induced Raman behavior of individual (R)‐di‐2‐naphthylprolinol molecules on a Ag‐modified Ag electrode

The applicability of surface‐enhanced Raman spectroscopy is demonstrated to probe the adsorption behavior of individual molecules on a Ag electrode. High‐quality SERS spectra of (R)‐di‐2‐naphthylprolinol (DNP) were obtained from ultradilute solutions (10⁻¹² M ) on the Ag‐nanoparticle‐modified Ag electrode, which is attributed to the high electromagnetic (EM) effect of the SERS‐active system as well as to the strong adsorption and interaction of DNP molecules with Ag. The stable SERS spectra present remarkable potential dependence, which gives evidence for the behavior of individual DNP molecules on the Ag surface. Based on statistical analysis for the probability of DNP molecules located in ‘hot spots’, we propose an SERS mechanism for individual molecules in the electrode system, in combination with the hot‐spot model and orientation of the probe molecules. Copyright © 2010 John Wiley & Sons, Ltd.     

Nd：YAG1064nm激发的核黄素在银胶体系中的表面增强拉曼散射谱

Ｎｄ：ＹＡＧ１０６４ｎｍ激发的核黄素在银胶体系中的表面增强拉曼散射谱张崇起，胡风霞，方炎（首都师范大学物理系，首都师范大学综合所，首都师范大学实验中心北京１０００３７）ＦｏｕｒｉｅｒＴｒａｎｓｆｏｒｍＳｕｒｆａｃｅ－ＥｎｈａｎｃｅｄＲａｍａｎＳｐｅｃ...     

Protein adsorption drastically reduces surface‐enhanced Raman signal of dye molecules

There is an increasing interest in developing surface enhancement Raman spectroscopy methods for intracellular biomolecule and for in vitro protein detection that involve dye or protein–dye conjugates. In this work, we have demonstrated that protein adsorption on silver nanoparticle (AgNP) can significantly attenuate the surface‐enhanced Raman spectroscopy (SERS) signal of dye molecules in both protein/dye mixtures and protein/dye conjugates. SERS spectra of 12 protein/dye mixtures were acquired using 4 proteins [bovine serum albumin (BSA), lysozyme, trypsin, and concanavalin A] and three dyes [Rhodamine 6G, adenine, and fluorescein isothiocyanate (FITC)]. Besides the protein/dye mixtures, spectra were also obtained for the free dyes and four FITC‐conjugated proteins. While no SERS signal was observed in protein/FITC mixtures or conjugates, a significantly reduced SERS intensity (up to 3 orders of magnitude) was observed for both R6G and adenine in their respective protein mixtures. Quantitative estimation of the number of dye molecules absorbed onto AgNP implied that the degree of R6G SERS signal reduction in the R6G/BSA sample is 2 to 3 orders of magnitude higher than what could be accounted for by the difference in the amount of the absorbed dyes. This finding has significant implications for both intracellular SERS analyses and in vitro protein detection using SERS tagging strategies that rely on Raman dyes as reporter molecules. Copyright © 2009 John Wiley & Sons, Ltd.     

Near‐infrared surface‐enhanced Raman spectroscopy (NIR‐SERS) studies on oxyheamoglobin (OxyHb) of liver cancer based on PVA‐Ag nanofilm

A near‐infrared surface‐enhanced Raman spectroscopy (NIR‐SERS) method was employed for oxyheamoglobin (OxyHb) detection to develop a simple blood test for liver cancer detection. Polyvinyl alcohol protected silver nanofilm (PVA‐Ag nanofilm) used as the NIR‐SERS active substrate to enhance the Raman scattering signals of OxyHb. High quality NIR‐SERS spectrum from OxyHb adsorbed on PVA‐Ag nanofilm can be obtained within 16 s using a portable Raman spectrometer. NIR‐SERS measurements were performed on OxyHb samples of healthy volunteers (control subjects, n = 30), patients (n = 40) with confirmed liver cancer (stage I, II and III) and the liver cancer patients after surgery (n = 30). Meanwhile, the tentative assignments of the Raman bands in the measured NIR‐SERS spectra were performed, and the results suggested cancer specific changes on molecule level, including a decrease in the relative concentrations and the percentage of aromatic amino acids of OxyHb, changes of the vibration modes of the C_aH_m group and pyrrole ring of OxyHb of liver cancer patients. In this paper, principal component analysis (PCA) combined with independent sample T test analysis of the measured NIR‐SERS spectra separated the spectral features of the two groups into two distinct clusters with the sensitivity of 95.0% and the specificity of 85.7%. Meanwhile, the recovery situations of the liver cancer patients after surgery were also assessed using the method of discriminant analysis‐predicting group membership based on PCA. The results show that 26.7% surgeried liver cancer patients were distinguished as the normal subjects and 63.3% were distinguished into the cancer. Our study demonstrated great potentials for developing NIR‐SERS OxyHb analysis into a novel clinical tool for non‐invasive detection of liver cancers. Copyright © 2013 John Wiley & Sons, Ltd.     

SERS detection of red organic dyes in Ag‐agar gel

Micro‐Raman spectroscopy has been widely employed in the last few years for the study of artworks, allowing for the characterization of a high class of pictorial materials. However, the detection of organic dyes by conventional Raman spectroscopy is quite difficult, due to the high fluorescence provided by these compounds. Recently, remarkable improvements have been achieved by the introduction of the surface enhanced Raman spectroscopy (SERS) technique for the analysis of organic dyes. In the present work, a new method is presented, based on the use of a SERS probe made of agar‐agar coupled with silver nanoparticles, for a non‐destructive and minimally invasive micro‐extraction of dyes from textiles. Ag‐agar gel has been tested first on textile mock‐ups dyed with alizarin, purpurin and carminic acid. SERS measurements have been performed adopting laser light excitations at 514.5 and 785 nm of a micro‐Raman setup. Highly structured SERS band intensities have been obtained. After having verified the safety of the method by colorimetric, X‐ray fluorescence and attenuated total reflectance Fourier transform infrared techniques, a real case, a pre‐Columbian piece of textile, have been investigated by Ag‐agar gel. This cutting‐edge method offers new possibilities for a sensitive and non‐destructive analysis of fluorescent materials. Copyright © 2012 John Wiley & Sons, Ltd.     

Thiol‐modified gold‐coated glass as an efficient hydrophobic substrate for drop coating deposition Raman (DCDR) technique

In this paper we report an easy and low‐cost way to prepare a hydrophobic substrate for drop coating deposition Raman (DCDR) spectroscopy. This substrate is formed by a thiol‐modified Au‐coated glass and provides the Raman spectra with the same quality as the commercial Teflon‐coated stainless steel substrate (SpectRIM™, Tienta Sciences, Inc.) for model molecular systems – albumin solution and liposome suspension. Gold layer, similarly to polished steel in the commercial substrate, served as a highly refractive layer strongly increasing the Raman signal. The main advantage of introduced substrate is that it is simple and a low‐cost preparation easily manageable in every standard laboratory. Thus, it represents a promising alternative to commercial Teflon‐coated stainless steel substrate. Copyright © 2016 John Wiley & Sons, Ltd.     

Surface‐enhanced Raman spectra of dimethoate and omethoate

Surface‐enhanced Raman scattering (SERS) spectra are presented and analyzed for two important organophosphate pesticides, dimethoate (DMT) and omethoate (OMT). Very detailed SERS spectra were obtained by aggregated Ag hydrosols, both in aqueous suspension and dried on a glass substrate. The SERS and ordinary Raman spectra of DMT do not resemble each other, suggesting that a chemical reaction immediately occurs when DMT is adsorbed onto the metal surface. We propose that the reaction product is OMT, which is the oxygen analog of DMT, on the basis of the Raman and SERS spectra of OMT. Further support is derived from the calculated Raman spectra of DMT and OMT. Minor wavenumber and intensity differences that are observed between the SERS spectra of DMT reaction product and those of OMT could be related to different metal/adsorbate interaction modes. The results can be useful in the development of new analytical methods for the determination of pesticide residues in food. Copyright © 2010 John Wiley & Sons, Ltd.