钨/低活化钢钎焊用铁基非晶钎料与接头微结构

为了连接W和CLF-1 RAFM钢,设计出由低活化元素组成的Fe-B-Si、Fe-B-Si-Sn、Fe-B-Si-Cr-(Sn)、Fe-B-Si-P-(Cr,Sn)、Fe-B-Si-Mn-(Ga,Sn)和Fe-B-Si-(Cr,Mn,Ga,Ta,Sn)系列Fe基非晶钎料,结合熔体快淬技术制备出非晶合金箔带,并对W/CLF-1 RAFM钢接头微结构进行了对比研究。采用X-射线衍射仪对箔带样品与焊缝进行了相鉴定;通过差热分析测量了非晶箔带的熔化温度和液相线温度;利用光学金相和电子探针分析了焊缝组织形貌和元素分布。结果表明,利用Fe-B-Si、Fe-B-Si-Cr和Fe-B-Si-Mn-Sn非晶钎料可获得结构完整的W/CLF-1钢接头;前两种钎料得到的焊缝组织基体相为α-Fe固溶体,而含Mn钎料形成的焊缝基体为马氏体组织;在高温钎焊过程中,这些Fe基非晶钎料中的高B含量促使FeWB、FeW2B2和Fe3B型金属间化合物在焊缝中形成,并有效地阻止了W元素向低活化钢基体长程扩散。所设计的低活化Fe基非晶钎料可用于W和低活化钢的连接和接头性能研究。     

W/Fe/CuCrZr热等静压模块组织及性能分析

为实现面向等离子体材料钨(W)和热沉材料铜铬镐(CuCrZr)合金的可靠连接,对纯铁(Fe)作为W/CuCrZr合金热等静压连接中间层的可行性进行了探索性研究.在850℃/150MPa/135min的热等静压参数下制作了W/Fe/CuCrZr合金的实验模块,分别对连接界面进行了焊接界面、微观形貌、组织成分及剪切力学性能...     

W/RAFM 钢偏滤器靶板的结构分析与寿命预测

探究RAFM 钢作为偏滤器靶板热沉的替换材料，验证其在3 种不同工况下的结构强度并预测其在交变载荷下的疲劳寿命。得出3S_m 法则下W/RAFM 钢偏滤器靶板最大可承受热负荷为8MW·m⁻²。结合中国聚变工程实验堆(CFETR)的设计目标，如果以ITER 偏滤器两年运行周期为设计准则，最大承受热负荷为7MW·m⁻²。考虑到偏滤器靶板区域呈现高热负荷低中子辐照、挡板和DOME板区域低热负荷高中子辐照特性，可以采用W/Cu 和W/RAFM 双路偏滤器靶板的结构设计。     

316L/RAFM钢电子束焊对接接头的微观组织与力学性能研究

在150kV/39mA的焊接参数下进行了316L/RAFM钢电子束焊工艺实验,对接头微观组织与力学性能进行了测试分析。在存在磁偏转的情况下,有效焊接深度达到了18mm,且焊接接头性能良好。     

Fe含量和粒径对Fe/Cu颗粒膜结构和磁性的影响

采用共蒸发法制备不同组分的Fe/Cu颗粒膜,将样品分两组进行退火和不退火处理. 根据测量及分析,确定了不同成分的Fe/Cu颗粒膜的相组成和晶体结构;找出了 Fe/Cu颗粒膜矫顽力与粒径的关系,利用此关系由自发形核理论可知,提高功率,快速蒸镀薄膜,可得到细密颗粒的Fe/Cu颗粒膜,从而降低矫顽力,减少磁滞损耗.     

RAFM钢TIG焊和电子束焊疲劳性能实验和分析模拟

利用ANSYS 对低活化铁素体马氏体(RAFM)钢进行非熔化极气体保护焊(TIG 焊)与电子束焊的抗疲劳模拟分析，再利用SDS200 电液伺服疲劳试验机对TIG 焊和电子束焊的两种RAFM 钢试件进行实验。通过施加相同梯度负荷对TIG 焊和电子束焊试件进行焊缝的疲劳性能实验。与实验结果对比分析，结果显示电子束焊优于 TIG 焊，但在一定负载下可以用TIG 焊代替电子束焊。     

斜齿轮激光熔覆Fe基合金组织与性能研究

采用激光熔覆技术在斜齿轮钢表面制备Fe基熔覆层.通过光学显微镜、显微硬度计对熔覆层进行金相组织与显微硬度分析,采用磨损机对熔覆层和基材进行摩擦实验.结果表明:当激光功率为750W,送粉速率为20g/min,扫描速度10mm/s,离焦量为16.4mm时,铁基熔覆层与基体结合界面有明显的白亮带,激光熔覆效果较好,熔覆层的显...     

Pd/Fe和PdFe/Fe多层膜中的振荡行为

采用磁控溅射法制备了Pd/Fe和Pd_1-xFe_x/Fe多层膜.利用变换梯度磁强计测量了样品的M_s.发现层间耦合是铁磁性的,M_s具有长程振荡,周期为4ML.振荡的相位和周期在Pd_0.966Fe_0.034/Fe和Fd_0.944Fe_0.056/Fe系统中保持不变.就Pd/Fe多层膜中是否存在内层的Pd负极化和长程的铁磁耦合振荡进行了讨论,并分析了不同计算结果以及理论计算与实验结果之间存在差异的原因. 关键词：     

Fe-B-Si非晶钎焊W/CLF-1接头组织和性能研究

通过电弧熔炼制备了Fe75B16.67Si8.33非晶合金,通过真空钎焊获得了钨/低活化钢接头.通过对钎焊接头表面形貌、微观组织、成分和力学性能的表征,发现在1250℃保温10min下所获得的钎焊接头界面无孔洞、裂纹等宏观缺陷,接头组织中生成了Fe固溶体、Fe3B和FeWB金属间化合物,拉伸强度高达450MPa.     

130W/70K大冷量单级G-M制冷机的性能研究

为满足高温超导等工程应用项目的大冷量需求,对130W/70K大冷量单级G-M制冷机系统进行了结构设计、理论计算和制冷性能测试,测得其制冷性能为最低温度18.1K,制冷量131.2W/70K。由于回热器性能优劣对制冷机性能有所影响,通过回热器不同填料方式对制冷机性能进行测试,结果表明,相比于采用单一磷青铜网填料的制冷机,采用磷青铜网和铅球作为复合蓄冷材料可以提高制冷机的制冷性能。     

Magnetoresistance of Fe3O4/Au/Fe3O4 and Fe3O4/Au/Fe spin-valve structures

A detailed study of the in-plane magnetotransport properties of spin valves with one and two Fe₃O₄ electrodes is presented. Fe₃O₄/Au/Fe₃O₄ spin valves exhibit a clear anisotropic magnetoresistance in small magnetic fields but no giant magnetoresistance (GMR). The absence of GMR in these structures is due to simultaneous magnetization reversal in the two Fe₃O₄ layers. By contrast, a negative GMR effect is measured on Fe₃O₄/Au/Fe spin valves. The negative GMR is attributed to an electron spin scattering asymmetry at the Fe₃O₄/Au interface or an induced spin scattering asymmetry in the Au interfacial layers.     

Desorption of H2 from W(110) and Fe covered W(110) surfaces

The kinetics of H₂ desorption from H/W(110) and H/Fe₁/W(110) were studied by measuring work function changes Δø vs time at a number of temperatures. Combination with previously determined Δø vs coverage data and differentiation at various fixed coverages gave rate vs T data from which activation energies of desorption could be obtained. E vs coverage results agree well with previously determine ΔH_des results. In the case of H/Fe₁/W(110) this includes a rise from 20 to 30 kcal mol⁻¹ of H₂ at H/Fe = H/W > 0.3. Plots of rate −dθ/dt vs θ (θ being coverage in units of H/W) vary much more steeply than θ² at most coverages for both systems. The θ dependence can be explained almost quantitatively in terms of the variations of ΔH_des and surface entropy S_s with coverage, by assuming that rates of desorption are equal to the equilibrium rates of adsorption. The latter can be formulated thermodynamically, except for a sticking coefficient, s. Values for s(θ, T) can also be obtained and show relatively little temperature dependence.     

用于核聚变装置的W/Cu 穿管部件的制备与辐照性能研究

采用了两步热等静压法制备W/Cu 穿管部件,即先用热等静压(930℃,100MPa,2h)在钨块的孔内壁上覆一层无氧铜作为中间层,然后再用热等静压工艺(600℃,100MPa,2h)把W/Cu 复合块与CuCrZr 管串接起来。经过高热负荷辐照测试,部件经受住了1000 次10MW•m⁻² 高热负荷的辐照,满足使用要求。     

Structural and magnetic study of swift heavy ion irradiated W/Fe multilayer structure

The present study reports the effect of swift heavy ion irradiation on structural and magnetic properties of sputtered W/Fe multilayer structure (MLS) having bilayer compositions of [W(10 Å)/Fe(20 Å)]_10BL. The MLS is irradiated by 120 MeV Au⁹⁺ ions of fluences 1×10¹³ and 4×10¹³ ions/cm². Techniques like X-ray reflectivity (XRR), cross-sectional transmission electron microscopy (X-TEM) and DC magnetization with a vibrating sample magnetometer (VSM) are used for structural and magnetic characterization of pristine and irradiated MLS. Analysis of XRR data using Parratt’s formalism shows a significant increase in W/Fe layer roughness. X-TEM studies reveal that intra-layer microstructure of Fe layers in MLS becomes nano-crystalline on irradiation. DC magnetization study shows that with spacer layer thickness interlayer coupling changes between ferromagnetic to antiferromagnetic.     

Re_3W的点接触安德烈夫反射谱研究

本文通过对不同晶体结构Re_3W样品的点接触测量和对比研究,证实具有中心对称结构和非中心对称结构的Re_3W都是弱耦合Bardeen-Cooper-Schrieffer超导体,同时发现在两个相表面都可以形成很理想的点接触结,即电子通过界面时受到的非弹性散射很弱.将Re_3W样品置于大气环境近六个月后重新进行测量,仍然能够得到类似的结果,表明Re_3W具有很好的稳定性. Re_3W的这种优良特性,不仅可通过点接触实验得到的参数推算出Re_3W两个相的费米速度,而且提供了一种简单的方法,可以在点接触实验中利用Re_3W来印证针尖材料的费米速度和测量其自旋极化率等.作为尝试,本文用Re_3W/Ni点接触结测量了铁磁性金属Ni的自旋极化率,得到了与前人报道一致的结果.     

Interfacial resonance state probed by spin-polarized tunneling in epitaxial Fe/MgO/Fe tunnel junctions

The direct impact of the electronic structure on spin-polarized transport has been experimentally proven in high-quality Fe/MgO/Fe epitaxial magnetic tunnel junctions, with an extremely flat bottom Fe/MgO interface. The voltage variation of the conductance points out the signature of an interfacial resonance state located in the minority band of Fe(001). When coupled to a metallic bulk state, this spin-polarized interfacial state enhances the band matching at the interface and therefore increases strongly the conductivity in the antiparallel magnetization configuration. Consequently, the tunnel magnetoresistance is found to be positive below 0.2 V and negative above. On the other hand, when the interfacial state is either destroyed by roughness-related disorder or not coupled to the bulk, the magnetoresistance is almost independent on the bias voltage.     

Effect of swift heavy ion irradiation in Fe/W multilayer structures

Present study reports effect of swift heavy ion irradiation on structural and magnetic properties of sputtered Fe/W multilayer structures (MLS) having bilayer compositions of [Fe(20 Å)/W(10 Å)]_5BL and [Fe(20 Å)/W(30 Å)]_5BL. These MLS are irradiated by 120 MeV Au⁹⁺ ions up to fluence of 4 × 10¹³ ions/cm². X-ray reflectivity (XRR), wide-angle X-ray diffraction (WAXD), cross-sectional transmission electron microscopy (X-TEM) and magneto optical Kerr effect (MOKE) techniques are used for structural and magnetic characterization of pristine and irradiated MLS. Analysis of XRR data using Parratt's formalism shows a significant increase in W/Fe interface roughness. WAXD and X-TEM studies reveals that intra-layer microstructure of Fe-layers in MLS becomes nano-crystalline on irradiation. MOKE study shows increase in coercivity at higher fluence, which may be due to increase in surface and interface roughness after recrystallization of Fe-layers.     

Insights into the sonochemical decomposition of Fe(CO)5: theoretical and experimental understanding of the role of molar concentration and power density on the reaction yield

The present work analyses, in detail, the optimization of a sonochemical process with respect to concentration of precursor and power supplied in a system. This is due to that even a small change in power dramatically changes the high-energy conditions created with the bubble collapse. A model reaction that has been considered for this purpose involves the decomposition of Fe(CO)₅ in decalin solvent as this reaction is strongly influenced by the cavitation conditions. Sonochemical treatment of this carbonyl results in the formation of amorphous Fe₂O₃, which on heat treatment gives nanocrystalline Fe₂O₃. It has been observed that concentration and power density parameters play an important role to obtain higher decomposition of Fe(CO)₅ and hence higher yield of the amorphous Fe₂O₃ product. Also, using the experimentally observed results, a correlation (polynomial) has been developed.