Hexagonal AlN films grown on nominal and off-axis Si(0 0 1) substrates

Nucleation and growth of wurtzite AlN layers on nominal and off-axis Si(0 0 1) substrates by plasma-assisted molecular beam epitaxy is reported. The nucleation and the growth dynamics have been studied in situ by reflection high-energy electron diffraction. For the films grown on the nominal Si(0 0 1) surface, cross-sectional transmission electron microscopy and X-ray diffraction investigations revealed a two-domain film structure (AlN¹ and AlN²) with an epitaxial orientation relationship of [0 0 0 1]_AlN || [0 0 1]_Si and AlN¹ || AlN² || [1 1 0]_Si. The epitaxial growth of single crystalline wurtzite AlN thin films has been achieved on off-axis Si(0 0 1) substrates with an epitaxial orientation relationship of [0 0 0 1]_AlN parallel to the surface normal and 0 1 1 0_AlN || [1 1 0]_Si.     

The photoluminescence of ZnO thin films grown on Si (1 0 0) substrate by plasma-enhanced chemical vapor deposition

High-quality ZnO thin films have been grown on a Si(1 0 0) substrate by plasma-enhanced chemical vapor deposition (PECVD) using a zinc organic source (Zn(C₂H₅)₂) and carbon dioxide (CO₂) gas mixtures at a temperature of 180°C. A strong free exciton emission with a weak defect-band emission in the visible region is observed. The characteristics of photoluminescence (PL) of ZnO, as well as the exciton absorption peak in the absorption spectra, are closely related to the gas flow rate ratio of Zn(C₂H₅)₂ to CO₂. Full-widths at half-maximum of the free exciton emission as narrow as 93.4 meV have been achieved. Based on the temperature dependence of the PL spectra from 83 to 383 K, the exciton binding energy and the transition energy of free excitons at 0 K were estimated to be 59.4 meV and 3.36 eV, respectively.     

Surface and interfacial structure of epitaxial SrTiO3 thin films on (0 0 1) Si grown by molecular beam epitaxy

Effects of relaxation of interfacial misfit strain and non-stoichiometry on surface morphology and surface and interfacial structures of epitaxial SrTiO₃ (STO) thin films on (0 0 1) Si during initial growth by molecular beam epitaxy (MBE) were investigated. In situ reflection high-energy electron diffraction (RHEED) in combination with X-ray diffraction (XRD), atomic force microscopy (AFM), X-ray photoelectron spectrometry (XPS) and transmission electron microscopy (TEM) techniques were employed. Relaxation of the interfacial misfit strain between STO and Si as measured by in situ RHEED indicates initial growth is not pseudomorphic, and the interfacial misfit strain is relaxed during and immediately after the first monolayer (ML) deposition. The interfacial strain up to 15 ML results from thermal mismatch strain rather than lattice mismatch strain. Stoichiometry of STO affects not only surface morphology but interfacial structure. We have identified a nanoscale Sr₄Ti₃O₁₀ second phase at the STO/Si interface in a Sr-rich film.     

MgO films grown on yttria-stabilized zirconia by molecular beam epitaxy

MgO films were grown on (0 0 1) yttria-stabilized zirconia (YSZ) substrates by molecular beam epitaxy (MBE). The crystalline structures of these films were investigated using X-ray diffraction and transmission electron microscopy. Growth temperature was varied from 350 to 550 °C, with crystalline quality being improved at higher temperatures. The MgO films had a domain structure: (1 1 1)[1 1 2¯]_MgO(0 0 1)[1 0 0]_YSZ with four twin variants related by a 90° in-plane rotation about the [1 1 1]_MgO axis. The observed epitaxial orientation was compared to previous reports of films grown by pulsed laser deposition and sputtering and explained as resulting in the lowest interface energy.     

AlGaN photodetectors grown on Si(1 1 1) by molecular beam epitaxy

The fabrication and characterisation of Al_xGa_1−xN (0x0.35) photodetectors grown on Si(1 1 1) by molecular beam epitaxy are described. For low Al contents (<10%), photoconductors show high responsivities (10A/W), a non-linear dependence on optical power and persistent photoconductivity (PPC). For higher Al contents the PPC decreases and the photocurrent becomes linear with optical power. Schottky photodiodes present zero-bias responsivities from 12 to 5 mA/W (x=0−0.35), a UV/visible contrast higher than 10³, and a time response of 20 ns, in the same order of magnitude as for devices on sapphire substrate. GaN-based p–n ultraviolet photodiodes on Si(1 1 1) are reported for the first time.     

Structure and thermal stability of MOCVD ZrO2 films on Si (1 0 0)

The structure and thermal stability of ZrO₂ films grown on Si (1 0 0) substrates by metalorganic chemical vapor deposition have been studied by high-resolution transmission electron microscopy, selected area electron diffraction and X-ray energy dispersive spectroscopy. As-deposited films consist of tetragonal ZrO₂ nanocrystallites and an amorphous Zr silicate interfacial layer. After annealing at 850°C, some monoclinic phase is formed, and the grain size is increased. Annealing a 6 nm thick film at 850°C in O₂ revealed that the growth of the interfacial layer is at the expense of the ZrO₂ layer. In a 3.0 nm thick Zr silicate interfacial layer, there is a 0.9 nm Zr-free SiO₂ region right above the Si substrate. These observations suggest that oxygen reacted with the Si substrate to grow SiO₂, and SiO₂ reacted with ZrO₂ to form a Zr silicate interfacial layer during the deposition and annealing. Oxygen diffusion through the tetragonal ZrO₂ phase was found to be relatively easier than through the monoclinic phase.     

GaN/GaAs(1 0 0) superlattices grown by metalorganic vapor phase epitaxy using dimethylhydrazine precursor

Superlattices of cubic gallium nitride (GaN) and gallium arsenide (GaAs) were grown on GaAs(1 0 0) substrates using metalorganic vapor phase epitaxy (MOVPE) with dimethylhydrazine (DMHy) as nitrogen source. Structures grown at low temperatures with varying layer thicknesses were characterized using high resolution X-ray diffraction and atomic force microscopy. Several growth modes of GaAs on GaN were observed: step-edge, layer-by-layer 2D, and 3D island growth. A two-temperature growth process was found to yield good crystal quality and atomically flat surfaces. The results suggest that MOVPE-grown thin GaN layers may be applicable to novel GaAs heterostructure devices.     

Epitaxial growth of ZnO thin films on Si substrates by PLD technique

Epitaxial ZnO thin films have been grown on Si(1 1 1) substrates at temperatures between 550 and 700 °C with an oxygen pressure of 60 Pa by pulsed laser deposition (PLD). A ZnO thin film deposited at 500 °C in no-oxygen ambient was used as a buffer layer for the ZnO growth. In situ reflection high-energy electron diffraction (RHEED) observations show that ZnO thin films directly deposited on Si are of a polycrystalline structure, and the crystallinity is deteriorated with an increase of substrate temperature as reflected by the evolution of RHEED patterns from the mixture of spots and rings to single rings. In contrast, the ZnO films grown on a homo-buffer layer exhibit aligned spotty patterns indicating an epitaxial growth. Among the ZnO thin films with a buffer layer, the film grown at 650 °C shows the best structural quality and the strongest ultraviolet (UV) emission with a full-width at half-maximum (FWHM) of 86 meV. It is found that the ZnO film with a buffer layer has better crystallinity than the film without the buffer layer at the same substrate temperature, while the film without the buffer layer shows a more intense UV emission. Possible reasons and preventive methods are suggested to obtain highly optical quality films.     

Growth of GaN based structures on Si(1 1 0) by molecular beam epitaxy

The growth of GaN based structures on Si(1 1 0) substrates by molecular beam epitaxy using ammonia as the nitrogen precursor is reported. The structural, optical and electrical properties of such structures are assessed and are quite similar to the ones obtained on Si(1 1 1) in-spite of the very different substrate surface symmetry. A threading dislocation density of 3.7×10⁹ cm⁻² is evaluated by transmission electron microscopy, which is in the low range of typical densities obtained on up to 2 μm thick GaN structures grown on Si(1 1 1). To assess the potential of such structure for device realization, AlGaN/GaN high electron mobility transistor and InGaN/GaN light emitting diode heterostructures were grown and their properties are compared with the ones obtained on Si(1 1 1).     

Growth of epitaxial ZnO films on Si (1 1 1) substrates with Cr compound buffer layer by plasma-assisted molecular beam epitaxy

Single crystalline ZnO film was grown on (1 1 1) Si substrate through employing an oxidized CrN buffer layer by plasma-assisted molecular beam epitaxy. Single crystalline characteristics were confirmed from in-situ reflection high energy electron diffraction, X-ray pole figure measurement, and transmission electron diffraction pattern, consistently. Epitaxial relationship between ZnO film and Si substrate is determined to be (0 0 0 1)_ZnO‖(1 1 1)_Si and [1 1 2¯ 0]_ZnO‖[0 1 1]_Si. Full-width at half-maximums (FWHMs) of (0 0 0 2) and (1 0 1¯ 1) X-ray rocking curves (XRCs) were 1.379° and 3.634°, respectively, which were significantly smaller than the FWHMs (4.532° and 32.8°, respectively) of the ZnO film grown directly on Si (1 1 1) substrate without any buffer. Total dislocation density in the top region of film was estimated to be ∼5×10⁹ cm⁻². Most of dislocations have a screw type component, which is different from the general cases of ZnO films with the major threading dislocations with an edge component.     

Effect of the N/Al ratio of AlN buffer on the crystal properties and stress state of GaN film grown on Si(1 1 1) substrate

The effect of the N/Al ratio of AlN buffers on the optical and crystal quality of GaN films, grown by metalorganic chemical vapor deposition on Si(1 1 1) substrates, has been investigated. By optimizing the N/Al ratio during the AlN buffer, the threading dislocation density and the tensile stress have been decreased. High-resolution X-ray diffraction exhibited a (0 0 0 2) full-width at half-maximum as low as 396 acrsec. The variations of the tensile stress existing in the GaN films were approved by the redshifts of the donor bound exiton peaks in the low-temperature photoluminescence measurement at 77 K.     

SIMS and Raman characterizations of ZnO:N thin films grown by MOCVD

Nitrogen was incorporated into ZnO films grown by metalorganic chemical vapour deposition (MOCVD) on ZnO substrates using DMZn-TEN, tert-butanol and diallylamine, respectively, as zinc, oxygen and doping sources. The carrier gas was either hydrogen or nitrogen and the partial pressure ratio (R_VI/II) was varied in order to favor the nitrogen incorporation and/or reduce carbon related defects. The ZnO films have been characterized by Micro-Raman scattering and SIMS measurements. SIMS measurements confirm the nitrogen incorporation with concentrations extending from ∼10¹⁹ cm⁻³ to ∼4×10²⁰ cm⁻³. Raman spectra show nitrogen local vibration modes in films grown at low R_VI/II ratio and using H₂ as carrier gas. However, a vibration band attributed to carbon clusters dominates the Raman spectra for films grown with N₂ carrier. The contribution of N complexes was discussed. The strain was calculated for the as-grown and annealed films and it changes from tensile to compressive after annealing.     

The influence of the Al pre-deposition on the properties of AlN buffer layer and GaN layer grown on Si (1 1 1) substrate

The influence of Al pre-deposition on the properties of AlN buffer layer and GaN layer grown on Si (1 1 1) substrate by metalorganic chemical vapor deposition (MOCVD) has been systematically studied. Compared with the sample without Al pre-deposition, optimum Al pre-deposition time could improve the AlN buffer layer crystal quality and reduce the root mean square (RMS) roughness. Whereas, overlong Al-deposition time deteriorated the AlN crystal quality and Al-deposition patterns could be found. Cracks and melt-back etching patterns appeared in the GaN layer grown without Al pre-deposition. With suitable Al-deposition time, crack-free 2.0 μm GaN was obtained and the full-width at half-maximum (FWHM) of (0 0 2) plane measured by double crystal X-ray diffraction (DCXRD) was as low as 482 arcsec. However, overlong Al-deposition time would result in a great deal of cracks, and the crystal quality of GaN layer deteriorated. The surface of GaN layer became rough in the region where the Al-deposition patterns were formed due to overlong Al-deposition time.     

The growth of Pd thin films on a 6H-SiC(0 0 0 1) substrate

Pd thin films, grown on Si-rich 6H-SiC(0 0 0 1) substrates, were studied by atomic force microscopy, electron diffraction and high-resolution transmission electron microscopy. It is concluded that the growth is successful only when all the growth process takes place at room temperature. Under these conditions a very good epitaxial growth of Pd is achieved, despite the large misfit (about 8.6%) between Pd and the substrate and the existence of a semi-amorphous layer between the thin film and the substrate. A large number of twins appear in these films.     

Selective area growth of GaN microstructures on patterned (1 1 1) and (0 0 1) Si substrates

Selective MOVPE growth of GaN microstructure on silicon substrates has been investigated using SiO₂ mask having circular or stripe window. In case of (0 0 1)substrate, grooves with (1 1 1) facets at the sides were made by using the etching anisotropy of a KOH solution. On the (1 1 1) facets of patterned silicon substrate (or on the as opened window region of (1 1 1) substrate), growth of wurtzite GaN was performed, of which the c-axis is oriented along the 1 1 1 axis of silicon. The photoluminescence and X-ray diffraction analysis were performed to characterize the single crystal to reveal the effect of the growth conditions of the intermediated layer and the microstructure.     

Subtle interplay between polytypism and preferred growth direction alignment in GaN nanorods non-catalytically grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy

GaN nanorods were grown on Si(1 1 1) substrates by using hydride vapor phase epitaxy, and the crystallographic characteristics associated with their preferred growth directions were investigated by utilizing synchrotron X-ray reciprocal space mapping in a grazing incidence geometry and scanning electron microscopy. Crystallographic analysis reveals that the nanorods containing both wurtzite and zinc blende phase tend to have narrower distribution of the preferred growth directions than those containing only wurtzite phase. This tendency is partly attributed to the subtle interplay between polytypism and the preferred growth directions of GaN nanorods.     

Structure evolution of Zn cluster on Si (0 0 1) substrate for ZnO nanostructure growth

In this paper, Monte Carlo simulations are carried out for Zn cluster supported on a static Si (0 0 1) substrate to estimate the morphological evolution of self-catalysis growth of ZnO nanostructures. The tight-binding many-body potential and the Lennard–Jones potential are used to describe Zn–Zn and Zn–Si interactions, respectively. The dynamic processes of Zn cluster in the temperature field decomposing and wetting effects are visualized through the simulation. The Zn atomic aggregates that randomly disperse on the Si (0 0 1) substrate with different shapes, such as a dimer, trimer, multimer and atomic chain, would act as catalytic nucleation sites for the following growth of the ZnO nanostructure. This phenomenon provides a sound explanation for the formation of randomly orientated and diversified ZnO nanostructures on the Si (0 0 1) substrate.     

Fabrication of 2D ordered arrays of cobalt silicide nanodots on (0 0 1)Si substrates

Two-dimensional (2D) periodic arrays of Co metal and Co silicide nanodots were successfully fabricated on (0 0 1)Si substrate by using the polystyrene (PS) nanosphere lithography (NSL) technique and thermal annealing. The epitaxial CoSi₂ was found to start growing in samples after annealing at 500 °C. The sizes of the Co silicide nanodots were observed to shrink with annealing temperature. From the analysis of the selected-area electron diffraction (SAED) patterns, the crystallographic relationship between the epitaxial CoSi₂ nanodots and (0 0 1)Si substrates was identified to be [0 0 1]CoSi₂//[0 0 1]Si and (2 0 0)CoSi₂//(4 0 0)Si. By combining the planview and cross-sectional TEM examination, the epitaxial CoSi₂ nanodots formed on (0 0 1)Si were found to be heavily faceted and the shape of the faceted epitaxial CoSi₂ nanodot was identified to be inverse pyramidal. The observed results present the exciting prospect that with appropriate controls, the PS NSL technique promises to offer an effective and economical patterning method for the growth of a variety of large-area periodic arrays of uniform metal and silicide nanostructures on different types of silicon substrates.     

Properties of ZnO films grown on (0 0 0 1) sapphire substrate using H2O and N2O as O precursors by atmospheric pressure MOCVD

In this paper, we compare the properties of ZnO thin films (0 0 0 1) sapphire substrate using diethylzinc (DEZn) as the Zn precursor and deionized water (H₂O) and nitrous oxide (N₂O) as the O precursors, respectively in the main ZnO layer growth by atmospheric pressure metal–organic chemical vapor deposition (AP-MOCVD) technique. Surface morphology studied by atomic force microscopy (AFM) showed that the N₂O-grown ZnO film had a hexagonal columnar structure with about 8 μm grain diameter and the relatively rougher surface compared to that of H₂O-grown ZnO film. The full-widths at half-maximum (FWHMs) of the (0 0 0 2) and () ω-rocking curves of the N₂O-grown ZnO film by double-crystal X-ray diffractometry (DCXRD) measurement were 260 and 350 arcsec, respectively, indicating the smaller mosaicity and lower dislocation density of the film compared to H₂O-grown ZnO film. Compared to H₂O-grown ZnO film, the free exciton A (FX_A) and its three phonon replicas could be clearly observed, the donor-bound exciton A⁰X (I₁₀):3.353 eV dominated the 10 K photoluminescence (PL) spectrum of N₂O-grown ZnO film and the hydrogen-related donor-bound exciton D⁰X (I₄):3.363 eV was disappeared. The electron mobility (80 cm²/V s) of N₂O-grown ZnO film has been significantly improved by room temperature Hall measurement compared to that of H₂O-grown ZnO film.     

Investigation of nonpolar (1 1 2¯ 0) a-plane ZnO films grown under various Zn/O ratios by plasma-assisted molecular beam epitaxy

Structural and optical properties of nonpolar a-plane ZnO films grown with different II/VI ratios on r-plane sapphire substrates by plasma-assisted molecular beam epitaxy were investigated. Even by increasing the II/VI ratio across the stoichiometric flux condition a consistent surface morphology of striated stripes along the ZnO 〈0 0 0 1〉 direction without any pit formation was observed, which is contrary to polar c-plane ZnO films. Root mean square surface roughness, full width at half maximum values of X-ray rocking curves, defect densities, and photoluminescence were changed with the II/VI ratio. The sample grown with stoichiometric flux condition showed the lowest value of rms roughness, the smallest threading dislocation and stacking fault densities of ∼4.7×10⁸ cm⁻² and ∼9.5×10⁴ cm⁻¹, respectively, and the highest intensity of D^oX peak. These results imply that the stoichiometric flux growth condition is suitable to obtain superior structural and optical properties compared to other flux conditions.