一维六方准晶双材料中圆孔边共线界面裂纹的反平面问题

研究了一维六方准晶双材料中圆孔边不对称共线界面裂纹的反平面问题。利用Stroh公式和复变函数方法得到了声子场和相位子场耦合作用下的复势函数,给出了裂纹尖端应力强度因子和能量释放率的解析表达式。通过数值算例,讨论了圆孔半径和裂纹长度对应力强度因子的影响,以及耦合系数、声子场应力和相位子场应力对能量释放率的影响。结果表明:当圆孔半径不变时,应力强度因子随右裂纹长度的增大趋向稳定值。当相位子场应力取一定值时,能量释放率达到最小值,说明特定的相位子场应力可以抑制裂纹的扩展。     

Laplace方程有孔椭圆区域边值问题的解析解

本文利用相似流动替换方法 ,解决了中心有圆孔的椭园形区域上 Laplace方程第一类边值问题 ;采用分区域解法 ,给出了中心有椭园孔的椭园形区域上 Laplace方程第一类边值问题的解析通解 .这一结果在许多工程领域有重要应用 ,本文给出了油藏工程实例     

A circulating gravity wave in a cylindrical tank

A circular cylindrical vertical tank is partially filled with a liquid (Water) and a gas (air) above it. The top lid of the container rotates around the cylinder axis and induces a flow in the gas and the liquid. Above a critical rotational speed a large amplitude circulating gravity wave forms. The two phase flow problem will be reduced to a free surface single phase flow problem and the critical parameters, when the axis-symmetric flow becomes unstable with respect to the circulating gravity wave will be determined. (© 2015 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim)     

Action of a concentrated load on an elastic ring pressed into a circular hole in an anisotropic plate

A solution is obtained for the elastic equilibrium problem for an anisotropic plate with a circular hole into which is pressed a ring of arbitrary cross section symmetrical about the middle surface of the plate. Before deformation the outside radius of the ring differs from the radius of the hole in the plate by the amount of the permissible elastic displacements. A normal concentrated load is applied to the ring. The ring is analyzed in accordance with the theory of thin curved bars. A numerical example is given.I. Franko L'vov State University. Translated from Mekhanika Polimerov, No. 6, pp. 1054–1059, November–December, 1973.     

Coupled Frequencies of a Fluid in Circular Cylindrical Tank with an Elastic Inclusion in its Roof

A closed upright rigid circular cylindrical tank is filled with a compressible and inviscid fluid as a part of the tank roof is an elastic plate. It is supposed that the tank roof and the elastic plate are eccentrically and the plate is clamped. The problem about the determination of the free coupling vibrations of the received hydroelastic system is considered. Using the Bubnov‐Galerkin method, the frequency equation is obtained. Some numerical examples are made and the results show the influence of the sizes of the radius of the elastic plate as well as of the other parameters of the hydroelastic system on its coupled frequencies.     

低重环境下液体非线性晃动的稳态响应

在俯仰激励作用下,圆柱贮箱中液体晃动存在平面运动、旋转运动和平面运动中的旋转运动等,而这些运动的稳定、不稳定区间的分界线与贮箱的半径、充液深度、重力强度、表面张力系数和晃动阻尼等基本系统参数有关．据此,首先建立了液体非线性晃动的微分方程组,并借助变分原理建立了液体压力体积分形式的Lagrange函数;然后将速度势函数在自由液面处作波高函数的级数展开,通过变分从而导出自由液面运动学和动力学边界条件非线性方程组;最后用多尺度法求解非线性方程组,就重力强度对圆柱形贮箱中液体非线性晃动的全局稳态响应的影响进行了详细的理论分析,并发现系统软硬特性的变化、跳跃和滞后等非线性现象．     

Lattice Boltzmann simulation of convective heat transfer of non-Newtonian fluids in impeller stirred tank

Lattice Boltzmann simulation of convective heat transfer of non-Newtonian fluids in an impeller stirred tank is performed. The curved and moving boundary methods combined with the unknown-index algorithm are used to solve the flow and thermal fields induced in a cold tank by an oscillating hot impeller. For a given maximum radius of the blades, the simulation results show that a rectangular impeller of large aspect ratio induces stronger heat transfer effect on the tank walls than the small aspect ratio. This is because the latter would cause worse field synergy than the former, i.e. the induced local velocities of fluid are mostly perpendicular to the temperature gradients. The convection effects on the tank walls are also improved as the oscillation amplitude of impeller increases until the swept areas of impeller are close to whole azimuth of the tank, i.e., oscillation amplitude of 90°. The maximum Nusselt number on the tank walls for power-law fluid flows of n = 0.7, 1 and 1.5 occurs at oscillation amplitude of 75°. Finally, it is found that the heat transfer effect on the tank walls is reduced as the power-law index of fluid increases.     

Expansions at small Reynolds numbers for the flow past a porous circular cylinder

The purpose of this article is to use the method of matched asymptotic expansions (MMAE) in order to study the two-dimensional steady low Reynolds number flow of a viscous incompressible fluid past a porous circular cylinder. We assume that the flow inside the porous body is described by the continuity and Brinkman equations, and the velocity and boundary traction fields are continuous across the interface between the fluid and porous media. Formal expansions for the corresponding stream functions are used. We show that the force exerted by the exterior flow on the porous cylinder admits an asymptotic expansion with respect to low Reynolds numbers, whose terms depend on the characteristics of the porous cylinder. In addition, by considering Darcy's law for the flow inside the porous circular cylinder, an asymptotic formula for the force on the cylinder is obtained. Also, a porous circular cylinder with a rigid core inside is considered with Brinkman equation inside the porous region. Stress jump condition is used at the porous–liquid interface together with the continuity of velocity components and continuity of normal stress. Some particular cases, which refer to the low Reynolds number flow past a solid circular cylinder, have also been investigated.     

半无穷平面到半无穷长圆管的低雷诺数流动

本文利用匹配法和配置法求出了粘性流体从半无穷平面到半无穷长圆管的Stokes流动的无穷级数形式的解.结果表明,经过圆柱半径的一半路程之后,速度剖面和Poiseuille剖面只差1%.初始段长度比Dagan的有限长圆管情形显著缩短,在孔口外的半无穷空间内,孔口右边的边界只对孔口附近一倍管径的区域有强烈影响.在此以外的区域内几乎没有影响.此外,本文还对压力和流量的关系进行了研究.     

Path planning,modeling and simulation of an autonomous articulated heavy construction machine performing a loading cycle

This research presents path planning and tracking for an articulated large wheel loader during the travel portion of a loading cycle. The study proposes a methodology for path planning, modeling, simulation and control of such vehicles; the analysis focuses on all of these components together and explains the relation among them. The developed methodology for path planning takes into account the dynamics and the performance characteristics of the heavy construction articulated vehicles, it also takes into account the construction working site constraints. The path optimization criterion is based on distance and cusp minimization without neglecting the constraints imposed by the size of the vehicle and its stable turning radius. The proposed path planning methodology is an extension and an improvement for Reeds and Shepp algorithm for a point shortest path calculation. The optimal path is consisted of circular arcs and straight segments, the radius is constant and identical for each arc in the desired path, the radius assumed to be similar to the minimum turning radius of the machine. When optimizing articulated machine path; to best account for machine size and articulation; more than one approach are discussed and compared. The machine is modeled and simulated during tracing the pre-defined planned path. The machine model includes the main frames, tires and a steering controller. The developed PID controller is used to keep machine lateral position within the pre-defined path while traveling with constant speed. The results showed an acceptable optimized path which the machine is able to track closely.     

On the hydrodynamic interaction of two circular cylinders oscillating in a viscous fluid

The present paper deals with the plane flow fields induced by two parallel circular cylinders with radiia andb oscillating in a direction which is i) parallel or ii) perpendicular to the plane containing their axes. The effect of the cylinders' hydrodynamic interaction on steady streaming has been studied analytically at high frequency by the method of matched asymptotic expansions.It is found that ifa=b the steady streaming is directed symmetrically to the cylinders while whenab (in the case i)) the secondary steady flow is directed towards the larger cylinder and one of the outer steady vortices disappears.It is shown in case i) that the drag force acting on each cylinder is smaller than the same force experienced on a single cylinder with the same radius which is placed in an unbounded oscillating flow. When the cylinder radii are equal, the drag is greater on the forward cylinder than on the rear one.In contrast, in case ii), wherea=b, it is shown that the drag on each of the two cylinders is greater than the drag acting on a single cylinder with the same radius placed in an unbounded oscillating stream and also each of the cylinders experiences a repulsive force in a direction perpendicular to the oscillating flow.     

Dense underflow into a lake or reservoir—Sub-critical flow.

Steady two-dimensional flow of a dense stream down a slight embankment into a lake or a reservoir is considered. The inflowing water is separated from the ambient lake water by a density interface. This work follows on from earlier work in which the flows down a steep incline with a relatively high flow rate were considered. Here, the flow is slow and the entry angle is small, resulting in waves on the interface. The fluid is assumed to be of finite depth and the incoming channel makes an angle α to the horizontal. Limiting flows are found when the fluid separates at a stagnation point or alternatively when the waves reach maximum steepness. The regions in parameter space where such solutions are obtained are delineated for different flow conditions.     

具有四条裂纹的圆形孔口问题的应力分析

利用复变函数的方法,通过构造保角映射研究了具有四条裂纹(一对非对称共线裂纹和一对对称共线裂纹)的圆形孔口的平面弹性问题,给出了裂纹尖端应力强度因子的解析解.并由此模拟出了具有三条裂纹、对称四条裂纹、非对称共线双裂纹、对称共线双裂纹的圆形孔口,以及非对称十字裂纹,十字裂纹,T形裂纹问题.     

Fundamental frequency of a circular membrane with a strip of small length

A circular membrane with an arbitrarily placed internal strip of small length is concerned in this article. A two-term asymptotic expansion for the fundamental frequency of the membrane, as the length of the strip approaching to zero, is specified. Comparing it with the one [8] derived for the membrane with an internal circular core, it is found that the position of the internal constraint has more effect than the shape of the internal constraint on the fundamental frequency. The asymptotic approximation is also compared with the numerical data computed by the dual boundary element method [2] for a circular membrane of radius 1 with a radially placed internal strip of length 2c. These two sets of data are in good agreement. The relative error is less than 3 % as c is less than or equal to 0.1, for all positions of the strip. Moreover, the relative error is less than 1 % as c is less than or equal to 0.01.     

Fundamental frequency of a circular membrane with a strip of small length

A circular membrane with an arbitrarily placed internal strip of small length is concerned in this article. A two-term asymptotic expansion for the fundamental frequency of the membrane, as the length of the strip approaching to zero, is specified. Comparing it with the one [8] derived for the membrane with an internal circular core, it is found that the position of the internal constraint has more effect than the shape of the internal constraint on the fundamental frequency. The asymptotic approximation is also compared with the numerical data computed by the dual boundary element method [2] for a circular membrane of radius 1 with a radially placed internal strip of length 2c. These two sets of data are in good agreement. The relative error is less than 3 % as c is less than or equal to 0.1, for all positions of the strip. Moreover, the relative error is less than 1 % as c is less than or equal to 0.01.     

The ice‐fishing problem: the fundamental sloshing frequency versus geometry of holes

We study an eignevalue problem with a spectral parameter in a boundary condition. This problem for the Laplace equation is relevant to sloshing frequencies that describe free oscillations of an inviscid, incompressible, heavy fluid in a half‐space covered by a rigid dock with some apertures (an ice sheet with fishing holes). The dependence of the fundamental eigenvalue on holes' geometry is investigated. We give conditions on a plane region guaranteeing that the fundamental eigenvalue corresponding to this region is larger than the fundamental eigenvalue corresponding to a single circular hole. Examples of regions satisfying these conditions and having the same area as the unit disk are given. New results are also obtained for the problem with a single circular hole. On the other hand, we construct regions for which the fundamental eigenfrequency is larger than the similar frequency for the circular hole of the same area and even as large as one wishes. In the latter examples, the hole regions are either not connected or bounded by a rather complicated curves. Copyright © 2004 John Wiley & Sons, Ltd.     

圆形孔口裂纹的反平面剪切问题的解析解

利用复变函数方法,通过构造保角映射,研究了带裂纹的圆形孔口的反平面剪切问题,给出了Ⅲ型裂纹问题的应力强度因子.在极限情形下,求得Griffith裂纹在裂纹尖端处应力强度因子,这与已有的结果完全一致.最后数值算例给出了半经和裂纹长度对应力强度因子的影响.     

Finite amplitude long-wave instability of a thin viscoelastic fluid during spin coating

This paper investigates the stability of a thin incompressible viscoelastic fluid designated as Walters’ liquid B″ during spin coating. The long-wave perturbation method is proposed to derive a generalized kinematic model of the film flow. The method of normal mode is applied to study the linear stability. The amplitude growth rates and the threshold conditions are characterized subsequently and summarized as the by-products of the linear solutions. Using the multiple scales method, the weakly nonlinear stability analysis is studied for the evolution equation of a film flow. The Ginzburg–Landau equation is determined to discuss the threshold conditions of the various critical flow states. The study reveals that the rotation number and the radius of the rotating circular disk generate the destabilizing effects. Moreover, the viscoelastic parameter k indeed plays a more significant role in destabilizing the film flow than a thin Newtonian fluid during spin coating [27].     

Capillary driven Oscillations of a Free Liquid Interface under Non‐Isothermal Conditions

In this study the reorientation behavior of a free liquid interface in a partly filled right circular cylinder upon a step reduction in gravity is investigated experimentally. The experiments focus on the investigation of non‐isothermal boundary conditions on the liquid reorientation. The situation is similar to a spacecraft which enters a ballistic flight after the end of thrust. Heat flux between the liquid propellant and the tank wall occurs and influences the behavior of the liquid reorientation. (© 2004 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

半无穷长圆管内的低雷诺数入口流

1969年Lew及Fung[1]计算了圆管内的低雷诸数入口流.1982年Dagan等人[2]得到了有限长圆柱形孔道内蠕动流的级数解.[1]中所得的数值解实质上代表有限长圆管内的低雷诺数入口流,因为一般解中的富氏积分已用富氏级数代替.本文直接计算富氏积分,更精确地求出了真正的半无穷长圆管内Stokes入口流的速度分布,压力分布以及流函数,与此对应的入口段长度为圆管半径的1.2倍,接近于Lew及Fung得到的结果1.3倍.此外,本文还研究了配置法的收敛性,证明了此法在入口流问题中具有很好的收敛性,因此可以在其他类似的问题中采用.