Determination of Rh, Pd and Pt in urine samples using a pre-concentration sequential injection analysis system coupled to a quadrupole-inductively coupled plasma-mass spectrometer

The proposed flow system was developed in order to minimize the drawbacks related to the PGEs determination by quadrupole-inductively coupled plasma-mass spectrometry (Q-ICP-MS). It was intended not only to lower the limits of detection (LODs) but also to eliminate the interferences originating from some atomic and molecular ions produced in the argon plasma. This was accomplished by means of an on-line sample clean-up/pre-concentration step, using a chelating resin (Metalfix™ Chelamine™) in which Rh, Pd and Pt were preferably retained when compared with the interfering species.

The results obtained by using the developed flow system in the analysis of urine samples are presented. With a sampling rate of 9 samples h⁻¹ (i.e., 27 determinations) and a sample consumption of ca. 10 mL, the developed flow system allowed linear calibration plots up to 100 ng L⁻¹ with detection limits of 1.2 ng L⁻¹ (Rh), 0.4 ng L⁻¹ (Pd) and 0.9 ng L⁻¹ (Pt). Repeatability studies showed good precision (R.S.D.%, n = 5): 3.7% (Rh); 2.6% (Pd) and 2.4% (Pt), for 10 ng L⁻¹; 2.4% (Rh); 1.4% (Pd) and 1.9% (Pt), for 50 ng L⁻¹; and 1.3% (Rh); 0.58% (Pd) and 0.62% (Pt), for 100 ng L⁻¹. By spiking human urine samples, recovery tests were performed, and the values obtained ranged between 89% and 105% (Rh); 90% and 104% (Pd); and 93% and 105% (Pt).     

The effect of signal suppression and mobile phase composition on the simultaneous analysis of multiple classes of acidic/neutral pharmaceuticals and personal care products in surface water by solid-phase extraction and ultra performance liquid chromatography-negative electrospray tandem mass spectrometry

A new multi-residue method for the determination of 25 acidic/neutral pharmaceuticals (antibiotics, anti-inflammatory/analgesics, lipid regulating agents, diuretics, triazides, H2-receptor antagonists, cardiac glicozides and angiotensin II antagonists) and personal care products (sunscreen agents and preservatives) in surface water with the usage of a new technique: ultra performance liquid chromatography–negative electrospray tandem mass spectrometry (UPLC–MS/MS) was developed and validated. The novel UPLC system with 1.7 μm particle-packed column allowed for good resolution of analytes with the application of low mobile phase flow rates (0.05 mL min⁻¹) and short retention times (from 4.7 min to 13.3 min) delivering a fast and cost-effective multi-residue method. SPE with the usage of Oasis MCX strong cation-exchange mixed-mode polymeric sorbent was chosen for sample clean-up and concentration. The influence of mobile-phase composition, matrix assisted ion suppression and SPE recovery on the sensitivity of the method was identified and quantified. The instrumental limits of quantification varied from 0.2 μg L⁻¹ to 30 μg L⁻¹. The method limits of quantification were at low nanogram per litre levels and ranged from 0.3 ng L⁻¹ to 30 ng L⁻¹. The instrumental and method intra-day and inter-day repeatabilities were on average less than 5%. The method was successfully applied for the determination of PPCPs in River Taff. Thirteen compounds were determined in river water at levels ranging from a single to a few hundred nanograms per litre. Among them were ten pharmaceuticals (aspirin, salicylic acid, ketoprofen, naproxen, diclofenac, ibuprofen, mefenamic acid, furosemide, sulfasalazine and valsartan) and three personal care products (methyl- and ethylparaben and 4-benzophenone).     

Diagnosis of copper ions in vascular tracts using a fluorine-doped carbon nanotube sensor

The voltammetric assay of Cu(II) was investigated using a carbon nanotube electrode (CNE) and fluorine immobilized onto a carbon nanotube electrode (FCNE) in cyclic voltammetry (CV), square-wave (SW) stripping voltammetry, and chronoamperometry. Optimum SW conditions were attained at working ranges of 0.01–0.11 ng L⁻¹ Cu(II) (11 points), and a relative standard deviation of 1.68% (RSD, n = 15) was observed at 10.0 μg L⁻¹ Cu(II). Within a 200 s accumulation time, detection limit of 0.006 μg L⁻¹ was attained. The life span of each electrode was more than 1 month. The sensor was applied to tap water, blood, and rat tail vascular (in vivo). It was found that the sensor could be used with an interface system in the assay of live cells and non-treated blood.     

Voltammetric determination of glucose based on reduction of copper(II)–glucose complex at lanthanum hydroxide nanowire modified carbon paste electrodes

A novel voltammetric method for the determination of β-d-glucose (GO) is proposed based on the reduction of Cu(II) ion in Cu(II)(NH₃)₄²⁺–GO complex at lanthanum(III) hydroxide nanowires (LNWs) modified carbon paste electrode (LNWs/CPE). In 0.1 mol L⁻¹ NH₃·H₂O–NH₄Cl (pH 9.8) buffer containing 5.0 × 10⁻⁵ mol L⁻¹ Cu(II) ion, the sensitive reduction peak of Cu(II)(NH₃)₄²⁺–GO complex was observed at −0.17 V (versus, SCE), which was mainly ascribed to both the increase of efficient electrode surface and the selective coordination of La(III) in LNW to GO. The increment of peak current obtained by deducting the reduction peak current of the Cu(II) ion from that of the Cu(II)(NH₃)₄²⁺–GO complex was rectilinear with GO concentration in the range of 8.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 3.5 × 10⁻⁷ mol L⁻¹. A 500-fold of sucrose and amylam, 100-fold of ascorbic acid, 120-fold of uric acid as well as gluconic acid did not interfere with 1.0 × 10⁻⁵ mol L⁻¹ GO determination.     

Time measurement-visual analysis of nickel(II) using autocatalytic reaction with sodium sulfite/hydrogen peroxide system and its application to the length detection-flow analysis

Trace amounts of nickel(II) can function as a trigger (=reaction initiator) in an autocatalytic reaction with the sodium sulfite/hydrogen peroxide system. Based on this finding, sub-μg L⁻¹ levels of nickel(II) were determined by a time measurement using the autocatalytic reaction. The detection range using the above method was 10⁻⁹–10⁻⁵ M, the detection limit (3σ) was 8.1 × 10⁻¹⁰ M (0.047 μg L⁻¹), and the relative standard deviation was 2.66% at nickel(II) concentration of 10⁻⁷ M (n = 7). This method was applied to length detection-flow injection analysis. The detection range for the flow injection analysis was 2 × 10⁻⁹–2 × 10⁻³ M. The detection limit (3σ) was 1.4 × 10⁻⁹ M (0.082 μg L⁻¹), and the relative standard deviation was 1.86 at initial nickel(II) concentration of 10⁻⁶ M (n = 7).     

Determination of dioxopromethazine hydrochloride by capillary electrophoresis with electrochemiluminescence detection

The paper presents a rapid method for the determination of dioxopromethazine hydrochloride (DPZ), an antihistamine drug, by the capillary electrophoresis with electrochemiluminescene detection (CE–ECL) using tris(2,2′-bipyridyl)ruthenium(II) (Ru(bpy)₃²⁺) reagent. This CE–ECL detection method has high sensitivity, good selectivity and reproducibility for DPZ analysis. Under the optimized conditions: separation capillary, 38 cm length (25 μm i.d.); sample injection, 10 s at 8 kV; separation voltage, 12.5 kV; running buffer, 20 mmol L⁻¹ sodium phosphate of pH 6.0; detection potential, 1.15 V; 50 mmol L⁻¹ of phosphate buffer (pH 7.14) containing 5 mmol L⁻¹ of Ru(bpy)₃²⁺ in ECL detection cell, the detection limit of DPZ was 0.05 μmol L⁻¹ (S/N = 3). The linear range extended from 5 to 100 μmol L⁻¹. The linear curve obtained was Y = 181.62 + 9.28X with a correlation coefficient of 0.9970. The relative standard deviations of the ECL intensity and the migration time for six continuous injections of 5 μmol L⁻¹ DPZ were 3.7% and 0.92%, respectively. The CE–ECL method was applied to analyze DPZ in real samples including tablets, rat serum and human urine, and satisfactory results were obtained without interference from samples matrix. The CE–ECL technique was proved to be a potential method for the detection of DPZ in clinic analysis.     

Cyclodextrin-enhanced fluorescence and photochemically-induced fluorescence determination of five aromatic pesticides in water

The effect of β-cyclodextrin (β-CD) and hydroxypropyl-β-cyclodextrin (HP-β-CD) aqueous solutions upon the fluorescence and photochemically-induced fluorescence (PIF) properties of five pesticides, including coumatetralyl, pirimiphos-methyl, chlorpyriphos, deltamethrin and fenvalerate was investigated. A 1:1 stoichiometry was found for the β-CD and HP-β-CD complexes formed with all compounds. Binding constant values, ranging between about 90 and 830 M⁻¹ were calculated using the iterative nonlinear least-squares regression approach. Cyclodextrin-enhanced fluorescence and PIF methods were developed for the determination of these pesticides with linear dynamic ranges over two orders of magnitude, and limits of detection (LOD) between 0.2 and 54 ng ml⁻¹ according to the compound. Application to the analysis of tap water and river water samples yielded satisfactory recoveries (88–116%). The method seems to be suitable for environmental water analysis.     

Flow injection hydride generation electrothermal atomic absorption spectrometric determination of toxicologically relevant arsenic in urine

Analytical procedure for the determination of toxicologically relevant arsenic (the sum of arsenite, arsenate, monomethylarsonate and dimethylarsinate) in urine by flow injection hydride generation and collection of generated inorganic and methylated hydrides on an integrated platform of a transverse-heated graphite atomizer for electrothermal atomic absorption spectrometric determination (ETAAS) is elaborated. Platforms are pre-treated with 2.7 μmol of zirconium and then with 0.10 μmol of iridium which serve both as an efficient hydride sequestration medium and permanent chemical modifier. Arsine, monomethylarsine and dimethylarsine are generated from diluted urine samples (10–25-fold) in the presence of 50 mmol L⁻¹ hydrochloric acid and 70 mmol L⁻¹ l-cysteine. Collection, pyrolysis and atomization temperatures are 450, 500, 2100 and 2150 °C, respectively. The characteristic mass, characteristic concentration and limit of detection (3σ) are 39 pg, 0.078 μg L⁻¹ and 0.038 μg L⁻¹ As, respectively. The limits of detection in urine are ca. 0.4 and 1 μg L⁻¹ with 10- and 25-fold dilutions. The sample throughput rate is 25 h⁻¹. Applications to several urine CRMs are given.     

Flow-injection immuno-bioassay for interleukin-6 in humans based on gold nanoparticles modified screen-printed graphite electrodes

A flow-injection electrochemical immunoassay system based on a disposable immunosensor for the determination of interleukin-6 (IL-6) was proposed. The immunosensor was prepared by entrapping horseradish peroxidase (HRP)-labeled IL-6 antibody into gold nanoparticles-modified composite membrane at a screen-printed graphite electrode. With a non-competitive immunoassay format, the immunosensor was inserted in the flow system with an injection of sample, and the injected sample containing IL-6 antigen was produced transparent immunoaffinity reaction with the immobilized HRP-labeled IL-6 antibody. The formed antigen–antibody complex inhibited partly the active center of HRP, and decreased the immobilized HRP to H₂O₂ reduction. The performance and factors influencing the performance of the immunosensor were investigated. Under optimal conditions, the current change obtained from the labeled HRP relative to thionine–H₂O₂ system was proportional to the IL-6 concentration in the range of 5–100 ng L⁻¹ with a detection limit of 1.0 ng L⁻¹ (at 3δ). The flow-injection immunoassay system could automatically control the incubation, washing and measurement steps with acceptable reproducibility and good stability. Moreover, the proposed immunosensors were used to analyze IL-6 in human serum specimens. Analytical results of clinical samples show the developed immunoassay has a promising alternative approach for detecting IL-6 in the clinical diagnosis.     

An improved procedure for flow-based turbidimetric sulphate determination based on a liquid core waveguide and pulsed flows

An improved flow-based procedure is proposed for turbidimetric sulphate determination in waters. The flow system was designed with solenoid micro-pumps in order to improve mixing conditions and minimize reagent consumption as well as waste generation. Stable baselines were observed in view of the pulsed flow characteristic of the systems designed with solenoid micro-pumps, thus making the use of washing solutions unnecessary. The nucleation process was improved by stopping the flow prior to the measurement, thus avoiding the need of sulphate addition. When a 1-cm optical path flow cell was employed, linear response was achieved within 20–200 mg L⁻¹, described by the equation S = −0.0767 + 0.00438C (mg L⁻¹), r = 0.999. The detection limit was estimated as 3 mg L⁻¹ at the 99.7% confidence level and the coefficient of variation was 2.4% (n = 20). The sampling rate was estimated as 33 determinations per hour. A long pathlength (100-cm) flow cell based on a liquid core waveguide was exploited to increase sensitivity in turbidimetry. Baseline drifts were avoided by a periodical washing step with EDTA in alkaline medium. Linear response was observed within 7–16 mg L⁻¹, described by the equation S = −0.865 + 0.132C (mg L⁻¹), r = 0.999. The detection limit was estimated as 150 μg L⁻¹ at the 99.7% confidence level and the coefficient of variation was 3.0% (n = 20). The sampling rate was estimated as 25 determinations per hour. The results obtained for freshwater and rain water samples were in agreement with those achieved by batch turbidimetry at the 95% confidence level.     

Determination of alkylphenol and bisphenol A in beverages using liquid chromatography/electrospray ionization tandem mass spectrometry

A comprehensive analytical method based on liquid chromatography electrospray ionization tandem mass spectrometry (LC–ESI–MS/MS) with negative ionization mode has been developed for measuring of alkylphenols and bisphenol A in beverage samples. Concentration and clean up of samples were performed on 200 mg OASIS HLB solid extraction cartridges. The effects of mobile phases and additives on ionization were assessed. The recoveries for each compound ranged from 76.7 to 96.9% and reproducibilities were represented as having relative standard deviation (R.S.D.) below 10%. The limits of quantification (LOQ) of the method under multiple-reaction monitoring (MRM) acquisition mode were 0.04, 0.03 and 0.2 ng L⁻¹ for 2 L of mineral drinking water and 2.0, 1.8 and 8.0 ng L⁻¹ for 50 mL of soda beverages.     

Multi-elemental analysis of non-food packaging materials by inductively coupled plasma-time of flight-mass spectrometry

Commercial non-food packaging materials of four different matrices (paper, low density polyethylene (LDPE), polyethylene-polypropylene (PE-PP) and high density polyethylene (HDPE)) were examined for the content of Cr, Ni, Cu, Zn, As, Mo, Cd, Sb, Ba, Hg, Tl, Pb and U. The examined samples (0.17–0.35 g) were digested in HNO₃ and H₂O₂ (papers, LDPE and PE-PP) and in HNO₃, H₂SO₄ and H₂O₂ (HDPE) using microwave assisted high pressure system. The inductively coupled plasma-time of flight-mass spectrometry (ICP-TOFMS) has been employed as the detection technique. All measurements were carried out using internal standardization. Yttrium and rhodium (50 ng g⁻¹) were used as internal standards. The detection and quantification limits obtained were in the range of 0.005 ng g⁻¹ (⁵²Cr) to 0.51 ng g⁻¹ (⁶⁶Zn) and 0.015 μg g⁻¹ (⁵²Cr) to 2.02 μg g⁻¹ (⁶⁶Zn) of dry mass, respectively. The evaluated contents (mg kg⁻¹) of particular elements in the examined materials were as follows: 0.22–219; <1.05–9.03; 1.25–112; <2.02–449; <0.98–<1.30; <0.36–2.06; <0.29–113; <0.22–44.1; <0.06–57.4; <0.66–<0.88; <0.08–0.24; <0.13–1222 and <0.08–0.44 for Cr, Ni, Cu, Zn, As, Mo, Cd, Sb, Ba, Hg, Tl, Pb and U, respectively.     

Investigation of the photocatalytic degradation of organochlorine pesticides on a nano-TiO2 coated film

The photocatalytic degradation of organochlorine pesticides including -, β-, γ-, δ-hexachlorobenzene (BHC), dicofol and cypermethrin were carried out on a nano-TiO₂ coated films under UV irradiation in the air. The photocatalytic conditions, including the amount of TiO₂, irradiation time and the intensity of light were optimized. The pesticides were most effectively degraded under the condition of 2.24 mg/cm² on TiO₂ film and a 400 W UV irradiation of high-pressure mercury lamp with a wavelength of 365 nm. A typical organochlorine pesticide, 20 μg -BHC, was dipped onto the TiO₂ film surface and degraded completely within 20 min. In addition, the photocatalytic degradation pathways on the nano-TiO₂ coated film were discussed.     

Efficiency and mechanism of new poly(acryl-phenylamidrazone phenylhydrazide) chelating fiber for adsorbing trace Ga, In, Bi, V and Ti from solution

A new po1y(acrylphenylamidrazone phenylhydrazide) chelating fiber is synthesized from polyacrylonitrile fiber and used for preconcentration and separation of trace Ga(III), In(III), Bi(III), V(V) and Ti(IV) from solution (5–50 ng ml⁻¹ Ti(IV) or V(V) and 50–500 ng ml⁻¹ Ga(III), In (III) or Bi(III) in 1000–100 ml of solution can be enriched quantitatively by 0.15 g of fiber at a 4 ml min⁻¹ flow rate in the pH range 5–7 with recoveries >95%). These ions can be desorbed quantitatively with 20 ml of 4 M hydrochloric acid at 2 ml min⁻¹ from the fiber column. When the fiber which had been treated with concentrated hydrochloric acid and washed with distilled water until neutral was reused eight times, the recoveries of the above ions by enrichment were still >95%. Two-hundred-fold to 10 000-fold excesses of Cu(II), Zn(II), Ca(II), Mn(II), Cr(III), Fe(III), Ba(II) and Al(III) caused little interference in the determination of these ions by inductively coupled plasma-atomic emission spectrometers (ICP-AES). The relative standard deviations for enrichment and determination of 50 ng ml⁻¹ Ga, In or Bi and 10 ng ml⁻¹ V or Ti are in the range 1.2–2.7%. The contents of these ions in real solution samples determined by this method were in agreement with the certified values of the samples with average errors <3.7%.     

Kinetic spectrophotometric method for rapid determination of trace formaldehyde in foods

A simple and sensitive kinetic-spectrophotometric method was developed for the determination of ultra trace amount of formaldehyde in food samples. The method was based on the oxidation of rhodamine B (RhB) by potassium bromate in sulfuric acid medium (formaldehyde as catalyst). The reaction was monitored by measuring the decrease in absorbance of the dye at 515 nm after 6 min. The developed method allowed the determination of formaldehyde in the range of 10–100 μg L⁻¹ with good precision, accuracy and the detection limit was down to 2.90 μg L⁻¹. The relative standard deviations for the determination of 10 and 60 μg L⁻¹ of formaldehyde were 3.0% and 1.9% (n = 10), respectively. The method was found to be sensitive, selective and was applied to the determination of formaldehyde in foods with satisfactory results.     

Immobilization enzyme fluorescence capillary analysis for determination of lactic acid

A new method for the determination of lactic acid based on the immobilization enzyme fluorescence capillary analysis (IE-FCA) was proposed. Lactic dehydrogenase (LDH) was immobilized on inner surface of a capillary with glutaraldehyde, and an immobilized enzyme lactate capillary bioreactor (IE-LCBR) was formed for the determination of lactic acid. After nicotinamide adenine dinucleotide (NAD⁺) is mixed with lactic acid solution, it was sucked into the IE-LCBR and was detected at λ_ex 353 nm/λ_em 466 nm. Optimized conditions are as follows: the temperature is 38 °C; the reaction time is 15 min; the concentrations of Tris buffer (pH 8.8) and NAD⁺ are 0.1 mol L⁻¹ and 4 mmol L⁻¹, respectively; the concentration of LDH used for immobilization is 15 kU L⁻¹. The concentration of lactic acid is directly proportional to the fluorescence intensity measured from 0.50 to 2.0 mmol L⁻¹; and the analytical recovery of added lactic acid was 99–105%. The minimum detection limit of the method is 0.40 mmol L⁻¹ and sensitivity of the IE-CBR is 4.6 F mmol⁻¹ L⁻¹ lactate. Its relative standard deviation (R.S.D.) is ≤2.0%. This IE-FCA method was employed for determination of lactate in milk drink.     

Multiple square wave voltammetry for analytical determination of paraquat in natural water, food, and beverages using microelectrodes

This paper reports on the use of multiple square wave voltammetry (MSWV) for analytical determination of paraquat herbicide at gold microelectrode (Au-ME) in different samples of natural water, food, and beverages. In this work, the MSWV consisted in a sequence of four pairs of potential pulse in the same step and the interval potential evaluated was of the 0.0 V at −1.2 V versus Ag/AgCl 3.0 mol L⁻¹. The paraquat herbicide presented two reduction peaks, in −0.69 V and −0.99 V, with profile of the redox process totally reversible, and the use of multiple pulses allowed a detection of nanomolar levels after the optimization of experimental and voltammetric conditions. Analytical curves were constructed for pulse potential frequency of 250 s⁻¹, pulse amplitude of 50 mV, scan increment of 2 mV and pulse number of 8 pulses in a same step. The two reduction peaks showed that the peak currents were found to be directly proportional to the pesticide concentration in the range comprised between 5.0 × 10⁻⁷ mol L⁻¹ and 1.04 × 10⁻⁵ mol L⁻¹. With this, it was possible to determine detection limits (DL), which resulted in 0.044 μg L⁻¹ (0.044 ppb) and 0.146 μg L⁻¹ (0.146 ppb), respectively, for peak 1 and peak 2. DL results, obtained using MSWV, were 2–3 orders of magnitude lower (10⁻² to 10⁻³) less than those observed for traditional square wave voltammetry or published in literature, clearly pointing to the advantages arising from the possibility of using a MSWV for analytical purposes in contaminated matrices. In addition, the proposed methodology was applied in different samples of natural water, food and beverages without pre-treatment or pre-concentration step, where a recovery measurement indicated that the methodology could be employed to analyze paraquat in such matrices.     

Electrochemiluminescent behavior of allopurinol in the presence of Ru(bpy)(3)(2+)

The electrochemiluminescent (ECL) response of allopurinol was studied in aqueous media over a wide pH range (pH 2–13) using flow injection (FI) analysis. It was revealed that allopurinol itself had no ECL activity, but could greatly enhance the ECL of Ru(bpy)₃²⁺ in alkaline media giving rise to a sensitive FI-ECL response. The effects of experimental conditions including the mode of applied voltage signal, the potential of working electrode, pH value, the flow rate of carrier solution, and the concentration of Ru(bpy)₃²⁺ and allopurinol on the ECL intensity were investigated in detail. The most sensitive FI-ECL response of allopurinol was found at pH 12.0, where the FIA-ECL intensity showed a linear relationship with concentration of allopurinol in the range 1 × 10⁻⁸ mol L⁻¹ to 5 × 10⁻⁷ mol L⁻¹, and the detection limit was 5 × 10⁻⁹ mol L⁻¹.     

High-performance liquid chromatographic assay of phosphate and organophosphorus pesticides using a post-column photochemical reaction and fluorimetric detection

A sensitive method for the post-column reaction detection of organophosphorus pesticides is described. The method relies on photolysis of the organocompounds by irradiation with a low-pressure mercury lamp (main spectral line, 254 nm) in the presence of peroxydisulfate. The resultant orthophosphate was reacted with molybdate to form molybdophosphoric acid, which subsequently reacted with thiamine to generate thiochrome. Finally, the fluorescence intensity of thiochrome was measured at 440 nm with excitation at 375 nm. Factors affecting the rate of these reactions were optimized so that its contribution to the total band-broadening was negligible.

This detection system was used for the determination of phosphate, acephate and methamidophos, which were separated on an ODS column by isocratic reversed phase chromatography with acetonitrile–water as the mobile phase. A linear relationship between analyte concentration and peak area was obtained within the range 0.016–7.0 μg ml⁻¹ with correlation coefficients greater than 0.9995 and detection limits between 4 and 12 ng ml⁻¹. Intra- and inter-day precision values of about 1.2% R.S.D. (n = 10) and 2.1% R.S.D. (n = 30), respectively, were obtained.

Pesticide residues below ng ml⁻¹ levels could be determined in environmental waters when a preconcentration device was coupled on-line with the HPLC system. Detection limits as low as 0.01 ng ml⁻¹ were achieved for only 250 ml of sample. In the analyses of vegetables and grains, the detection limit was about 1 μg kg⁻¹.     

Effect of pH on the characteristics of potassium permanganate–luminol CL reaction in the presence of trace aluminum(III) and its analytical application

At pHs ≥ 11.45, trace Al was found to enhance the CL from luminol–KMnO₄ system. However, at pHs ≤ 10.42, it was found to inhibit strongly the CL from luminol–KMnO₄ system. The effect of pH, luminol and potassium permanganate concentrations on the kinetic characteristics of CL system was investigated in the presence of trace Al. On this basis, a flow injection inhibition chemiluminescence method was established for the determination of trace Al in this study. Under optimized conditions, the CL decreased linearly with Al(III) concentration in the range of 8–500 μg L⁻¹ and the detection limit (3σ) of 2 μg L⁻¹. The relative standard deviation (R.S.D.) is 3.6% for 100 μg L⁻¹ Al(III) (n = 11). The method has been applied to the determination of trace Al in real water samples with satisfactory results without the pretreatment of samples. The results given by the proposed method are in good agreement with those given by ICP-AES detection method.