无溶剂Fe3O4纳米流体的制备及表征

采用共沉淀法合成Fe3O4纳米粒子, 将含有硅氧烷基的离子型改性剂二甲基十八烷基氯化铵与Fe3O4纳米粒子进行接枝反应, 再用脂肪醇聚氧乙烯醚磺酸盐的长链阴离子交换Cl-, 在Fe3O4纳米粒子表面生成具有阴、 阳离子双电层结构的表面处理层, 得到无溶剂Fe3O4纳米流体. 研究结果表明, 在Fe3O4纳米粒子表面成功接枝了有机物长链, 改性的Fe3O4纳米粒子呈单分散分布, 其损耗剪切模量G″明显大于储能剪切模量G', 具有明显的流体行为, 在室温下即可流动.     

3D nitrogen-doped graphene aerogel-supported Fe3O4 nanoparticles as efficient electrocatalysts for the oxygen reduction reaction

Three-dimensional (3D) N-doped graphene aerogel (N-GA)-supported Fe(3)O(4) nanoparticles (Fe(3)O(4)/N-GAs) as efficient cathode catalysts for the oxygen reduction reaction (ORR) are reported. The graphene hybrids exhibit an interconnected macroporous framework of graphene sheets with uniform dispersion of Fe(3)O(4) nanoparticles (NPs). In studying the effects of the carbon support on the Fe(3)O(4) NPs for the ORR, we found that Fe(3)O(4)/N-GAs show a more positive onset potential, higher cathodic density, lower H(2)O(2) yield, and higher electron transfer number for the ORR in alkaline media than Fe(3)O(4) NPs supported on N-doped carbon black or N-doped graphene sheets, highlighting the importance of the 3D macropores and high specific surface area of the GA support for improving the ORR performance. Furthermore, Fe(3)O(4)/N-GAs show better durability than the commercial Pt/C catalyst.     

三重桥氧三核铁脂肪酸配合物FAB和EI质谱研究

本文报道三重桥氧三核铁脂肪酸配合物[Fe_3(μ_3～O)(μ-O_2CR)_6(H_2O)]_3~+(R=CH_3,C_2H_5,C_3H_7,C_4H_9,C_(15)H_(31)和C_(17)H_(35))的快原子轰击(FAB)和电子轰击(EI)质谱。在FAB—MS谱中观察到四种系列离子:Ⅰ.[Fe_3O(O_2CR)_n]~+n=2-6;Ⅱ.[Fe_3O(O_2CR)_nO]~+n=1-4;Ⅲ.[Fe_2O(O_2CR)_n]~+n=1-3;Ⅳ.[Fe_2(O_2CR)_n]~+n=2-4;以及与底物所形成的加合离子[Fe_3O(O_2CR)_n·NBA-1]~+n=3-5(NBA是间-硝基苄醇)。在EI—MS谱中,除上述Ⅰ—Ⅳ离子(其中n的数目略有差异)外,还观察到含三个配位水的完整阳离子[Fe_3(O_2CR)_6(H_2O)_3]~+及其与配体羧酸的加合离子[Fe_3O(0_2CR)_n(H_20)_3·RCOOH+H]~+n=4-6,(Fe_3O(O_2CR)_nO(H_2O)3·RCOOH+H]~+n=2—4和Fe(O_2CR)_n]~+n=1—3。分析了它们的断裂规律,探讨了从中所获得的有益启示。     

Sm掺杂对Fe2O3催化剂NH3-SCR反应活性及抗水抗硫性作用

氮氧化物(NO_x)是主要的环境污染物之一,会造成酸雨、光化学烟雾和温室效应等环境问题.氨选择性催化还原(NH₃-SCR)技术是目前控制NO_x排放的最有效技术.其中,Fe₂O₃催化剂因其良好的抗硫性和低廉的成本而受到广泛关注,有望用作NO_x消除催化剂,但是它的低温还原性差、脱硝效率低等缺点限制了其应用.近期研究表明,钐掺杂金属氧化物可以调节其表面酸碱性及氧化还原性,可有效提高氧化物催化剂的脱硝效率和抗水抗硫性能.因此,将铁、钐二者优势结合,为合成一种低温、高效、环境友好型脱硝催化剂提供了可能.本文通过柠檬酸辅助的溶胶凝胶法合成了一系列钐均匀掺杂入Fe₂O₃纳米颗粒的复合氧化物脱硝催化剂,采用X射线光电子能谱(XPS),氢气程序升温还原(H2-TPR),氨气程序升温脱附(NH₃-TPD)以及原位漫反射红外光谱(in situ DRIFTS)等方法研究了钐的掺杂对铁基催化剂脱硝效率和抗水抗硫性的影响,旨在揭示催化剂表面物理化学性质和催化活性之间的关系.通过活性测试发现,钐的掺杂可以使Fe_0.94Sm_0.06O_x催化剂在175?325℃时实现>95%的脱硝效率和>93%的N2选择性.动力学测试研究表明,当基于催化剂的比表面积计算时,Fe_0.94Sm_0.06O_x催化剂的脱硝效率是纯Fe₂O₃催化剂的11倍;基于质量计算时则为37倍.此外,250℃时抗水抗硫测试结果显示,Fe_0.94Sm_0.06O_x催化剂可以在通入200×10^-6SO₂+5 vol%H₂O,空速为90000 h^-1时脱硝效率保持83%达168小时,并且在切断H₂O和SO₂后,该催化剂的脱硝效率可以很快完全恢复.XPS和H2-TPR结果表明,钐的掺杂使Fe_0.94Sm_0.06O_x催化剂的表面产生了大量的表面吸附氧,从而促进了NO的氧化以及快速NH₃-SCR反应的进行.NH₃-TPD与原位DRIFTS结果表明,钐的掺杂增强了催化剂的表面酸性,有效地提高了NH₃的吸附和活化能力,进而提高了催化剂的脱硝效率.另外,钐的掺杂还可以促使NH₄HSO₄在Fe_0.94Sm_0.06O_x催化剂表面较低温度下的分解,从而使催化剂具有很好的抗水抗硫性能.     

Fe3O4@MCM-48–SO3H:合成苯并[f]色烯并[2,3-d]嘧啶酮的高效、可磁性分离纳米催化剂（英文）

Sulfonic acid groups were grafted onto three different types of synthesized magnetic nanoparticles, namely Fe3O4, Fe3O4@SiO2, and Fe3O4@MCM‐48. The sulfonic acid‐functionalized nanoparticles were evaluated as catalysts for the synthesis of 5‐aryl‐1H‐benzo[f]chromeno[2,3‐d]pyrimidine‐2,4(3H,5H)‐dione derivatives in terms of activity and recyclability. Their catalytic activities were compared with that of the homogeneous acid catalyst 1‐methylimidazolium hydrogen sulfate ([HMIm][HSO4]). The activity of Fe3O4@MCM‐48–SO3H was comparable to those of the other heter‐ogeneous and homogeneous catalysts.     

High spin d5 complexes of tris(6-hydroxymethyl-2-pyridylmethyl)amine (H3L): hepta-coordinated [Mn(H3L)]Cl2 and linear trinuclear [Fe3L2](ClO4)3

Reaction of MnCl(2).4H(2)O with H(3)L (H(3)L = tris(6-hydroxymethyl-2-pyridylmethyl)amine) in methanol gives hepta-coordinated [Mn(H(3)L)]Cl(2) involving attachment of Mn(II) to all four nitrogens and three hydroxymethyl arms. Reaction of H(3)L with Fe(ClO(4))(2).6H(2)O in CH(3)CN in the presence of NaO(2)CC(6)H(5) in an attempt to make [Fe(III)OH(H(3)L)(O(2)CC(6)H(5))](ClO(4)), a putative model for soybean lipoxygenase-1, instead gave rise to the linear triiron(III) complex [Fe(3)L(2)](ClO(4))(3) with all three hydroxymethyl arms deprotonated and forming three alkoxide bridges between each Fe(III) centre. The central Fe(III) is hexa-coordinated to only the alkoxide bridges and flanked by two hepta-coordinated iron(III) centres analogous to the Mn(ii) complex. [Fe(3)L(2)](ClO(4))(3) exhibits two reversible 1e(-) reductions to mixed-valence [Fe(3)L(2)](2+) and [Fe(3)L(2)](+) forms. Structure data and magnetochemistry on [Fe(3)L(2)](ClO(4))(3) reveals the tightest Fe-O-Fe angle (87.4 degrees ) and shortest Fe...Fe distance (2.834 A) yet found for any weakly antiferromagnetically-coupled high spin alkoxide-bridged di- or triiron(iii) system and challenges current theories involved in correlating the extent/nature of magnetic interactions in such systems based on Fe-O(bridge) distances and Fe-O-Fe angles. The central hexa-alkoxide coordinated Fe(III) is novel and shows a remarkable resistance towards reduction to Fe(II).     

Molecular [(fe(3))-(fe(3))] and [(fe(4))-(fe(4))] coordination cluster pairs as single or composite arrays

The synthesis of molecular cluster pairs is a challenge for coordination chemists due to the potential applications of these species in molecular spintronics or quantum computing. The ligand H(4)L, 1,3-bis-(3-oxo-3-(2-hydroxyphenyl)-propionyl)-2-methoxybenzene, has been successfully used to obtain a series of such complexes using the basic Fe(III) trinuclear carboxylates as starting materials. Synthetic control has allowed the isolation of the two molecular cluster pairs that form the composite [Fe(4)O(2)(PhCO(2))(6)(H(2)L)(pz)](2)[Fe(3)O(PhCO(2))(5)(py)(H(2)L)](2) (1). The dimers of trinuclear units, [Fe(3)O(PhCO(2))(5)(H(2)O)(H(2)L)](2) (2) and [Fe(3)O(o-MePhCO(2))(5)(H(2)L)(py)](2) (3), and the dimers of tetranuclear units, [Fe(4)O(2)(PhCO(2))(6)(H(2)L)(pz)](2) (4) and [Fe(4)O(2)(o-MePhCO(2))(6)(H(2)L)(pz)](2) (5), are presented here. The magnetic properties of the reported aggregates show that they are pairs of semi-independent clusters weakly interacting magnetically as required for two-qubit quantum gates.     

Monitoring reaction intermediates in the FeCl3-catalyzed michael reaction by nuclear inelastic scattering

We present a study of the metal-centered vibrations in the first step of the Fe(III)-catalyzed Michael reaction. Nuclear inelastic scattering of synchrotron radiation was carried out on a shock-frozen solution of FeCl3.6H2O in 2-oxocyclopentane ethylcarboxylate (CPEH), as well as on the solid reference compounds FeCl3.6H2O, [N(CH3)4][FeCl 4], and Fe(acac) 3. In addition to the vibrations of the FeCl4(-) anion at 133 and 383 cm(-1), a multitude of modes associated with the complex Fe(CPE)2(H2O)2 could be identified. Normal-mode analysis on different isomers of the simplified model complex Fe(acac)2(H2O)2 as well as that of the full complex carrying two entire CPE ligands was carried out using density functional calculations. Comparison with experiment suggests that the facial bis(diketonato) isomer probably dominates in the reaction mixture. Thus, we have identified for the first time the isomeric structure of an iron-based intermediate of a homogeneous catalytic reaction using nuclear inelastic scattering.     

3d-Metal derivatives of the [Cu(I)(SO3)4]7- ion: structure and magnetism

The Cu(SO(3))(4)(7-) anion, which consists of a tetrahedrally coordinated Cu(I) centre coordinated to four sulfur atoms, is able to act as a multidentate ligand in discrete and infinite supramolecular species. The slow oxidation of an aqueous solution of Na(7)Cu(SO(3))(4) yields a mixed oxidation state, 2D network of composition Na(5){[Cu(II)(H(2)O)][Cu(I)(SO(3))(4)]}·6H(2)O. The addition of Cu(II) and 2,2'-bipyridine to an aqueous Na(7)Cu(SO(3))(4) solution leads to the formation of a pentanuclear complex of composition {[Cu(II)(H(2)O)(bipy)](4)[Cu(I)(SO(3))(4)]}(+); a combination of hydrogen bonding and π-π stacking interactions leads to the generation of infinite parallel channels that are occupied by disordered nitrate anions and water molecules. A pair of Cu(SO(3))(4)(7-) anions each act as a tridentate ligand towards a single Mn(II) centre when Mn(II) ions are combined with an excess of Cu(SO(3))(4)(7-). An anionic pentanuclear complex of composition {[Cu(I)(SO(3))(4)](2)[Fe(III)(H(2)O)](3)(O)} is formed when Fe(II) is added to a Cu(+)/SO(3)(2-) solution. Hydrated ferrous [Fe(H(2)O)(6)(2+)] and sodium ions act as counterions for the complexes and are responsible for the formation of an extensive hydrogen bond network within the crystal. Magnetic susceptibility studies over the temperature range 2-300 K show that weak ferromagnetic coupling occurs within the Cu(II) containing chains of Na(5){[Cu(II)(H(2)O)][Cu(I)(SO(3))(4)]}·6H(2)O, while zero coupling exists in the pentanuclear cluster {[Cu(II)(H(2)O)(bipy)](4)[Cu(I)(SO(3))(4)]}(NO(3))·H(2)O. Weak Mn(II)-O-S-O-Mn(II) antiferromagnetic coupling occurs in Na(H(2)O)(6){[Cu(I)(SO(3))(4)][Mn(II)(H(2)O)(2)](3)}, the latter formed when Mn was in excess during synthesis. The compound, Na(3)(H(2)O)(6)[Fe(II)(H(2)O)(6)](2){[Cu(I)(SO(3))(4)](2)[Fe(III)(H(2)O)](3)(O)}·H(2)O, contained trace magnetic impurities that affected the expected magnetic behaviour.     

Fe-Mn/Al2O3催化剂低温 NH3选择性催化还原 NO的性能

本文制备了一系列 Fe-Mn/Al2O3催化剂,并在固定床上考察了其 NH3低温选择性催化还原 NO的性能.首先考察了不同 Fe负载量制备的催化剂的脱硝性能,优选出最佳的 Fe负载量;在此基础上,研究了 Mn负载量对催化剂脱硝效率的影响;最后,对优选催化剂的抗 H2O和抗 SO2性能进行了实验研究;同时,对催化剂由于 SO2所造成的失活机制进行了考察.采用 N2吸附-脱附、X射线衍射、透射电镜、能量弥散 X射线谱、程序升温还原、程序升温脱附、X射线光电子能谱、热重和傅里叶变换红外光谱等方法对催化剂进行了表征.结果表明,最佳的 Fe和 Mn负载量均为8%,所制的8Fe-8Mn/Al2O3催化剂在150°C的脱硝效率可达近99%;同时,在整个低温测试区间(90–210°C)的脱硝效率均超过了92.6%. Fe在催化剂表面主要以 Fe3+形态存在,而 Mn主要包括 Mn4+和 Mn3+; Mn的添加提高了 Fe在催化剂表面的积累,促进了催化剂比表面积增大和活性物种分散,改善了催化剂氧化还原性能和对 NH3的吸附能力.催化剂的高活性主要是由于其具有较大的比表面积、高度分散的活性物种、增加的还原特性和表面酸性、较低的结合能、较高的 Mn4+/Mn3+和增强的表面吸附氧.此外,8Fe-8Mn/Al2O3的催化性能受 H2O和 SO2影响较小,抗 H2O和 SO2能力较强.同时,反应温度对催化剂的抗硫性有重要影响,在较低的反应温度下,催化剂抗硫性更好; SO2造成催化剂活性降低主要是由于催化剂表面硫酸盐物种的生成.一方面,表面硫酸铵盐的生成造成催化剂孔道堵塞和比表面积降低,减少了反应中的气固接触从而导致活性降低;另一方面,催化剂表面的活性物种被硫酸化,造成反应中的有效活性位减少,从而降低了催化剂活性.     

Heterometallic CeIII-FeIII-salicylate networks: models for corrosion mitigation of steel surfaces by the 'green' inhibitor,Ce(salicylate)3

The syntheses and structures of the novel Ce-Fe bimetallic complexes [[Fe(sal)2(bpy)]2Ce(NO3)(H2O)3].EtOH and [[Fe(sal)2(bpy)]4Ce2(H2O)11][salH]2.EtOH.3H2O (salH2 = salicylic acid) suggest Fe(3+)-sal2- units and Ce-OC(R)O-Fe bridging contribute to the formation of corrosion inhibitive layers on steel surfaces exposed to [Ce(salH)3(H2O)].     

Nine Diiron(II) Complexes of Three Bis-tetradentate Pyrimidine Based Ligands with NCE (E = S, Se, BH(3)) Coligands

Three bis-tetradentate acyclic amine ligands differing only in the arm length of the pyridine pendant arms attached to the 4,6-positions of the pyrimidine ring, namely, 4,6-bis[N,N-bis(2'-pyridylethyl)aminomethyl]-2-phenylpyrimidine (L(Et)), 4,6-bis[N,N-bis(2'-pyridylmethyl)aminomethyl]-2-phenylpyrimidine (L(Me)), and 4,6-[(2'-pyridylmethyl)-2'-pyridylethyl)aminomethyl]-2-phenylpyrimidine (L(Mix)) have been used to synthesize nine air-sensitive diiron(II) complexes: [Fe(II)(2)L(Et)(NCS)(4)]·MeOH·(3)/(4)H(2)O (1·MeOH·(3)/(4)H(2)O), [Fe(II)(2)L(Et)(NCSe)(4)]·H(2)O (2·H(2)O), [Fe(II)(2)L(Et)(NCBH(3))(4)]·(5)/(2)H(2)O (3·(5)/(2)H(2)O), [Fe(II)(2)L(Me)(NCS)(4)]·(1)/(2)H(2)O (4·(1)/(2)H(2)O), [Fe(II)(2)L(Me)(NCSe)(4)] (5), [Fe(II)(2)L(Me)(NCBH(3))(4)]·(3)/(2)H(2)O (6·(3)/(2)H(2)O), [Fe(II)(2)L(Mix)(NCS)(4)]·(1)/(2)H(2)O (7·(1)/(2)H(2)O), [Fe(II)(2)L(Mix)(NCSe)(4)]·(3)/(2)H(2)O (8·(3)/(2)H(2)O), and [Fe(II)(2)L(Mix)(NCBH(3))(4)]·(3)/(2)H(2)O (9·(3)/(2)H(2)O). Complexes 3·(5)/(2)H(2)O, 4·(1)/(2)H(2)O, 5, 6·(3)/(2)H(2)O, and 8·(3)/(2)H(2)O were structurally characterized by X-ray crystallography, revealing, in all cases, both of the iron(II) centers in an octahedral environment with two NCE (E = S, Se, or BH(3)) anions in a cis-position relative to one another. Variable temperature magnetic susceptibility measurements showed that all nine diiron(II) complexes are stabilized in the [HS-HS] state from 300 K to 4 K, and exhibit weak antiferromagnetic coupling. M?ssbauer spectroscopy confirmed the spin and oxidation states of eight of the nine complexes (the synthesis of air-sensitive complex 3 was not readily reproduced).     

Cyano-bridged FeIII2CuII3 and FeIII4NiII4 complexes: syntheses, structures, and magnetic properties

Two tricyanometallate precursors, (Bu4N)[(Tp4Bo)Fe(CN)3].H2O.2MeCN (1) and (Bu4N)[(pzTp)Fe(CN)3] (2) [Bu4N+ = tetrabutylammonium cation; Tp4Bo = tris(indazolyl)hydroborate; pzTp = tetrakis(pyrazolyl)borate], with a low-spin FeIII center have been synthesized and characterized. The reactions of 1 or 2 with [Cu(Me3tacn)(H2O)2](ClO4)2 (Me3tacn = N,N',N' '-trimethyl-1,4,7-triazacyclononane) afford two pentanuclear cyano-bridged clusters, [(Tp4Bo)2(Me3tacn)3Cu3Fe2(CN)6](ClO4)4.5H2O (3) and [(pzTp)2(Me3tacn)3Cu3Fe2(CN)6](ClO4)4.4H2O (4), respectively. Assembly reactions between 2 and [Ni(phen)(CH3OH)4](ClO4)2 (phen = 1,10-phenanthroline) or Zn(OAc)2.2H2O afford a molecular box [(pzTp)4(phen)4Ni4Fe4(CH3OH)4(CN)12](ClO4)4.4H2O (5) and a rectangular cluster [(pzTp)2Zn2Fe2(OAc)2(H2O)2(CN)6] (6). Their molecular structures were determined by single-crystal X-ray diffraction. In complexes 1 and 2, the central FeIII ions are coordinated by three cyanide carbon atoms and three nitrogen atoms of Tp4Bo- or pzTp-. Both complexes 3 and 4 show a trigonal-bipyramidal geometry, in which [(L)Fe(CN)3]- units occupy the apical positions and are linked through cyanide to [Cu(Me3tacn)]2+ units situated in the equatorial plane. Complex 5 possesses a cubic arrangement of eight metal irons linked through edge-spanning cyanide bridges, while complex 6 shows Zn2Fe2(CN)4 rectangular structure, in which FeIII and ZnII ions are alternately bridged by the cyanide groups. Intramolecular ferromagnetic couplings are observed for complexes 3-5, and they have S = 5/2, 5/2, and 6 ground states and appreciable magnetic anisotropies with negative D values equal to -0.49, -2.39, and -0.39 cm-1, respectively.     

Linking [M(III)3] triangles with "double-headed" phenolic oximes

Strapping two salicylaldoxime units together with aliphatic α,Ω-aminomethyl links in the 3-position gives ligands which allow the assembly of the polynuclear complexes [Fe(7)O(2)(OH)(6)(H(2)L1)(3)(py)(6)](BF(4))(5)·6H(2)O·14MeOH (1·6H(2)O·14MeOH), [Fe(6)O(OH)(7)(H(2)L2)(3)](BF(4))(3)·4H(2)O·9MeOH (2·4H(2)O·9MeOH) and [Mn(6)O(2)(OH)(2)(H(2)L1)(3)(py)(4)(MeCN)(2)](BF(4))(5)(NO(3))·3MeCN·H(2)O·5py (3·3MeCN·H(2)O·5py). In each case the metallic skeleton of the cluster is based on a trigonal prism in which two [M(III)(3)O] triangles are tethered together via three helically twisted double-headed oximes. The latter are present as H(2)L(2-) in which the oximic and phenolic O-atoms are deprotonated and the amino N-atoms protonated, with the oxime moieties bridging across the edges of the metal triangles. Both the identity of the metal ion and the length of the straps connecting the salicylaldoxime units have a major impact on the nuclearity and topology of the resultant cluster, with, perhaps counter-intuitively, the longer straps producing the "smallest" molecules.     

Lanthanide-3d cyanometalate chains Ln(III)-M(III) (Ln=Pr, Nd, Sm, Eu, Gd, Tb; M=Fe) with the tridentate ligand 2,4,6-tri(2-pyridyl)-1,3,5-triazine (tptz): evidence of ferromagnetic interactions for the Sm(III)-M(III) compounds (M=Fe, Cr)

A series of cyanide-bridged chain mixed Fe(III)/Ln(III) (Ln=Pr, Nd, Sm, Eu, Gd, Tb) complexes with the tridentate ligand 2,4,6-tri(2-pyridyl)-1,3,5-triazine (tptz) used as a capping group has been prepared. Reactions of tptz and LnCl3 with K3Fe(CN)6 yield a family of air-stable 1-D compounds {[Pr(tptz)(H2O)4Fe(CN)6].8H2O}infinity, {[Nd(tptz)(H2O)4Fe(CN)6].8H2O}infinity, {[Sm(tptz)(H2O)4Fe(CN)6].8H2O}, {[Eu(tptz)(H2O)4Fe(CN)6].6H2O}infinity, {[Gd(tptz)(H2O)4Fe(CN)6].6H2O}infinity, and {[Tb(tptz)(H2O)4Fe(CN)6].8H2O}infinity. Temperature dependent magnetic susceptibility studies of reveal that in , the Sm(III) and Fe(III) ions are ferromagnetically coupled with 3-D ordering occurring below 3.5 K. The appearance of the frequency dependent out-of-phase signal is explained in terms of an ordering with a spin glass-like behavior. To compare the magnetic behavior of with related compounds, {[Sm(tptz)(H2O)4Co(CN)6].8H2O}infinity and {[La(tptz)(DMF)(H2O)3Fe(CN)6].5H2O}infinity, {[Sm(tmphen)(DMF)3(H2O)Fe(CN)6].2H2O}infinity, {[Sm(tmphen)2(H2O)2Fe(CN)6].MeOH.13H2O}infinity and {[Sm(tmphen)2(H2O)2Cr(CN)6].MeOH.9H2O}infinity with 3,4,7,8-tetramethyl-1,10-phenanthroline (tmphen) were also prepared.     

含铁钛白粉的应用研究

本文对含铁钛白粉－钛白粉生产中的废品用作超强酸催化剂催化酯化反应进行了初步研究。结果表明：通过适当处理,可以将含铁钛白粉制造成固体超强酸,为废品利用开辟了一条新途径。     

A rational synthetic route leading to 3d-3d'-4f heterospin systems: self-assembly processes involving heterobinuclear 3d-4f complexes and hexacyanometallates

A novel heterospin system, [(CuL)Gd(H2O)3(Fe(CN)6)] x 4H2O, is obtained by reacting the mononuclear complex, [CuL], with gadolinium(III) nitrate, followed by the substitution of the nitrato groups with [Fe(CN)6](3-) ions (L2- = N,N'-propylenedi(3-methoxysalicylideneiminato)).     

Porous Fe3O4 nanoparticles: synthesis and application in catalyzing epoxidation of styrene

A facile route was employed to synthesize porous magnetite via reaction of FeCl(3)·6H(2)O with N(2)H(4)·H(2)O in ethylene glycol without any structure-directing agent. The resultant Fe(3)O(4) particles were characterized by transmission electron microscopy, N(2) adsorption, X-ray photoelectron spectroscopy, and thermal gravimetric analysis. It was demonstrated that the particle size varied in the range of 40-220 nm, and the pore size of particles was centered around 2 nm. The gases produced in the formation process of the particles played key role in the formation of the porous structure. The obtained porous magnetite was used as support to immobilize Au nanoparticles with size less than 2 nm with the assistance of L-cysteine. The as-prepared Fe(3)O(4) particles can effectively catalyze epoxidation of styrene, and the immobilization of Au nanoparticles on the Fe(3)O(4) support significantly improved the activity of the catalyst.     

卟啉H2TSPP和Ag(II)TSPP吸附在均分散Fe3O4胶体上的拉曼光谱

Surface Enhanced Raman Scattering (SERS) of tetrasodium meso-tetrakis (4-sulfonatophenyl) porphine (H2TSPP) and silver tetraphenylporphyrin (Ag(Ⅱ)TSPP) adsorbed spontaneously on uniform Fe3O4 colloids are recorded. The enhancement of Raman bands is approximately 30. An analysis of the SERS spectrum shows that on the Fe3O4 surface H2TSPP takes its diacid form H42+TSPP.     

NaCl和B2O3在修饰FeOχ催化剂中的协同作用

应用连续催化反应，ＸＰＳ，ＸＲＤ，Ｈ２－ＴＰＲ，Ｏ２－ＴＰＤ和Ｉｎ－ｓｉｔｕ Ｍｏｓｓｂａｕｅｒ谱等方法表征了一系列组成不同的ＮａＣｌ／Ｂ２Ｏ３／Ｆｅ２Ｏ３催化剂。结果表明ＮａＣｌ与Ｂ２Ｏ３在修饰ＦｅＯｘ催化剂上存在明显的协同作用，Ｂ２Ｏ３调变了ＦｅＯｘ的还原能力，ＮａＣｌ修饰了Ｂ２Ｏ３／ＦｅＯｘ使之具有很高的还原速度与晶格氧气化速度。催化剂的催化性能同这种协同作用密切相关。