Preconcentration procedure trace amounts of palladium using modified multiwalled carbon nanotubes sorbent prior to flame atomic absorption spectrometry: 1st Nano Update

A method for preconcentration of palladium at trace level on modified multiwalled carbon nanotubes columns and determination by flame atomic absorption spectrometry (FAAS) has been developed. Multiwalled carbon nanotubes (MWCNTs) were oxidized with concentrated HNO₃ and the oxidized multiwalled carbon nanotubes were modified with 5-(4′-dimethylamino benzyliden)-rhodanine, and then were used as a solid sorbent for preconcentration of Pd(II) ions. Factors influencing sorption and desorption of Pd(II) ions were investigated. The sorption of Pd(II) ions was quantitative in the pH range of 1.0–4.5, whereas quantitative desorption occurs with 3.0 mL 0.4 mol L^?1 thiourea. The amount of eluted palladium was measured using flame atomic absorption spectrometry. The effects of experimental parameters, including sample flow rate, eluent flow rate, and eluent concentration were investigated. The effect of coexisting ions showed no interference from most ions tested. The proposed method permitted a large enrichment factor (about 200). The relative standard deviation of the method was ±2.73% (for eight replicate determination of 2.0 μg mL^?1 of Pd(II)) and the limit of detection was 0.3 ng mL^?1. The method was applied to the determination of Pd(II) in water, road dust, and standard samples.     

Ultrasensitive determination of serum albumin using resonance light scattering based on ZnS-polyacrylic acid nanoparticles

ZnS-polyacrylic acid (ZnS-PAA) was prepared by an in situ polymerization method using nano-ZnS as core in the presence of acrylic acid (AA), and ZnS-PAA nanoparticles was characterized by ultraviolet spectrometry (UV) and transmission electron microscopy (TEM). Based on the significant increase of the resonance light scattering (RLS) intensity with the interaction between nanoparticles and serum albumin, RLS method was developed for the sensitive determination of serum albumin (BSA and HSA). Under optimum conditions, the change of the intensity (ΔI) of the RLS spectra at λ = 392 nm was linearly proportional to the concentration of BSA and HSA. The linear range was 1–100 ng mL^?1 for HSA and 1–120 ng mL^?1 for BSA, and the limit of detection (LOD) was 0.4 ng mL^?1 for HSA and 0.5 ng mL^?1 for BSA. This method proved to be very sensitive, rapid, simple and tolerant of most interfering substances.     

Copper(II)–neocuproine reagent for spectrophotometric determination of captopril in pure form and pharmaceutical formulations

A simple, rapid, sensitive and accurate spectrophotometric method for the determination of captopril in pure form and pharmaceutical formulations is developed. The procedure is based on the reaction of copper(II) with captopril in the presence of neocuproine (NC) (2,9-dimethyl-1,10-phenanthroline) reagent in acetate buffer at pH 5.0. Copper(II) is reduced easily by captopril to Cu(I)–neocuproine complex, which shows an absorption maximum at 448 nm. Beer’s law was obeyed in the concentration range 0.3–3.0 μg mL^?1 with a minimum detection limit (LOD) of 0.039 μg mL^?1 and a quantification limit (LOQ) of 0.129 μg mL^?1. For more accurate results, Ringbom optimum concentration ranges was 0.5–2.7 μg mL^?1. The apparent molar absorbtivity and Sandell sensitivity were calculated. The validity of the proposed method was tested by analyzing the pure and pharmaceutical formulations and compared well with those obtained by the official method and demonstrated good accuracy and precision.     

Assay of caffeoylquinic acids in Baccharis trimera by reversed-phase liquid chromatography

Baccharis trimera commonly named ‘carqueja’, is wide-spread in South America and are used as raw material for herbal medicines. A reversed-phase liquid chromatography (RP-LC) method coupled to diode array detector was developed for the analysis of caffeoylquinic acids (CQAs), the main compounds responsible for its digestive activity. The identity of the quinic acids was established by mass spectrometry and were them: 5-O-[E]-caffeoylquinic acid, 3,4-O-[E]-dicaffeoylquinic acid, 3,5-O-[E]-dicaffeoylquinic acid, 4,5-O-[E]-dicaffeoylquinic acid and a tricaffeoylquinic acid. The RP-LC method for the quantitation of the caffeoylquinic acids was validated according to ICH guidelines, based on the following parameters: linearity, selectivity, robustness, limits of detection and quantification, precision and recovery. Hydroalcoholic extracts were prepared by the maceration of the plant material with ethanol:water 1:1 (v/v) in a 0.1:25 g mL^?1 plant:solvent ratio in a water bath at 40 °C. Validation data indicated that the HPLC method proposed is suitable for the analysis of caffeoylquinic acids in B. trimera raw material. The results of the LOD and LOQ analyses for the 5-CQA were 4.1 μg mL^?1 and 12.5 μg mL^?1, respectively, 1.3 μg mL^?1, 3.9 μg mL^?1 for 4,5-diCQA and 1.7 μg mL^?1, 5.1 μg mL^?1 for triCQA. The levels of total CQAs ranged from 2.1 to 4.0 g% (w/w). The influence of season harvest and site collection was also evaluated and variations were observed in the results and can be related to phonologic phase, different locations, seasons and soil. Long term and photostability of plant material were carried out and was observed a stable behavior during the time of the experiments.     

Thermodynamic analysis of sorption isotherms of chromium(VI) anionic species on reed biomass

A new sorbent material for removing Cr(VI) anionic species from aqueous solutions has been investigated. Adsorption equilibrium and thermodynamics of Cr(VI) anionic species onto reed biomass were studied at different initial concentrations, sorbent concentrations, pH levels, temperatures, and ionic strength. Equilibrium isotherm was analyzed by Langmuir model. The experimental sorption data fit the model very well. The maximum sorption capacity of Cr(VI) onto reed biomass was found to be 33 mg · g^?1. It was noted that the Cr(VI) adsorption by reed biomass decreased with increase in pH. An increase in temperature resulted in a higher Cr(VI) loading per unit weight of the adsorbent. Removal of Cr(VI) by reed biomass seems to be mainly by chemisorption. The change in entropy (ΔS^°) and heat of adsorption (ΔH^°) for Cr(VI) adsorption on reed biomass were estimated as 2205 kJ · kg^?1 · K^?1 and 822 kJ · kg^?1, respectively. The values of isosteric heat of adsorption varied with the surface loading of Cr(VI).     

Thermodynamics and kinetics of adsorption of Cu(II) from aqueous solutions onto a new cation exchanger derived from tamarind fruit shell

A novel cation exchanger (TFS-CE) having carboxylate functionality was prepared through graft copolymerization of hydroxyethylmethacrylate onto tamarind fruit shell (TFS) in the presence of N,N′-methylenebisacrylamide as a cross-linking agent using K₂S₂O₈/Na₂S₂O₃ initiator system, followed by functionalisation. The TFS-CE was used for the removal of Cu(II) from aqueous solutions. At fixed solid/solution ratio the various factors affecting adsorption such as pH, initial concentration, contact time, and temperature were investigated. Kinetic experiments showed that the amount of Cu(II) adsorbed increased with increase in Cu(II) concentration and equilibrium was attained at 1 h. The kinetics of adsorption follows pseudo-second-order model and the rate constant increases with increase in temperature indicating endothermic nature of adsorption. The Arrhenius and Eyring equations were used to obtain the kinetic parameters such as activation energy (E_a) and enthalpy (ΔH^#), entropy (ΔS^#) and free energy (ΔG^#) of activation for the adsorption process. The value of E_a for adsorption was found to be 10.84 kJ · mol^?1 and the adsorption involves diffusion controlled process. The equilibrium data were well fitted to the Langmuir isotherm. The maximum adsorption capacity for Cu(II) was 64 · 10 mg · g^?1 at T = 303 K. The thermodynamic parameters such as changes in free energy (ΔG^°), enthalpy (ΔH^°), and entropy (ΔS^°) were derived to predict the nature of adsorption process. The isosteric heat of adsorption increases with increase in surface loading indicating some lateral interactions between the adsorbed metal ions.     

Application of modified multiwalled carbon nanotubes as solid sorbent for separation and preconcentration of trace amounts of manganese ions

In this work, the potential of modified multiwalled carbon nanotubes for separation and preconcentration of trace amounts of manganese ion is studied. Multiwalled carbon nanotubes were oxidized with concentrated HNO₃ and then modified with loading 1-(2-pyridylazo)-2-naphtol. Mn(II) ions could be quantitatively retained by modified multiwalled carbon nanotubes in the pH range of 8–9.5. Elution of the adsorbed manganese was carried out with 5.0 mL of 0.1 mol L^?1 HNO₃. Detection limit is 0.058 ng mL^?1 and analytical curve is linear in the range of 0.1 ng mL^?1–5.0 μg mL^?1 in the initial solution with a correlation coefficient 0.9977 and the preconcentration factor is 100. Relative standard deviation for eight replicate determination of 0.5 μg mL^?1 of manganese in the final solution is 0.41%. The effects of the experimental parameters, including the sample pH, flow rates of sample and eluent solution, eluent type, breakthrough volume and interference ions, were studied for preconcentration of Mn(II) ions in detail to optimize the conditions. The method was successfully applied for separation, preconcentration and determination of manganese in different samples.     

Validated voltammetric method for the determination of some antiprotozoa drugs based on the reduction at an activated glassy carbon electrode

A sensitive electrochemical procedure based on reduction of secnidazole (I), tinidazole (II) and ornidazole (III) at a glassy carbon electrode (GCE) was introduced. A study of the variation of the peak current with solution variables such as pH, ionic strength, concentration of drugs, possible interference, and instrumental variables such as scan rate, pulse amplitude, preconcentration time, accumulation potential, has resulted in the optimization of the reduction signal for analytical purposes. Linear calibration plots were obtained over the concentration ranges of 50–800, 50–750 μg mL^?1 for I, and both (II, III) respectively, in Britton–Robinson buffer of pH 7. The relative standard deviations of five replicate measurements of 1.0 and 10.0 μg mL^?1 of I, II and III concentrations were 4.7%, 4.9% and 5.3%, and 2.2%, 2.6% and 2.8%, respectively. The limits of detection (LOD) for I, II and III were found to be 2 × 10^?10, 3 × 10^?10 and 2.5 × 10^?10 mol L^?1 and limits of quantification (LOQ) for I, II and III were found to be 4.0 × 10^?8, 1.2 × 10^?8 and 4.4 × 10^?8 mol L^?1, respectively. The optimal conditions were: E_acc = ?0.9 V, t_acc = 30 s, scan rate = 20 mV s^?1, pulse-height = 90 mV and Britton–Robinson buffer of pH 7. The method was applied for the determination of the cited drugs both in raw materials and in pharmaceutical preparations with satisfactory results and compared with the official reference method. Complete validation of the proposed method was also done.     

Electrochemical immunosensors for interleukin-6. Comparison of carbon nanotube forest and gold nanoparticle platforms

Electrochemical immunosensors based on single wall nanotube (SWNT) forests and 5 nm glutathione-protected gold nanoparticles (GSH-AuNP) were developed and compared for the measurement of human cancer biomarker interleukin-6 (IL-6) in serum. Detection was based on sandwich immunoassays using multiple (14–16) horseradish peroxidase labels conjugated to a secondary antibody. Performance was optimized by effective blocking of non-specific binding (NSB) of the labels using bovine serum albumin. The GSH-AuNP immunosensor gave a detection limit (DL) of 10 pg mL^?1 IL-6 (500 amol mL^?1) in 10 μL calf serum, which was 3-fold better than 30 pg mL^?1 found for the SWNT forest immunosensor for the same assay protocol. The GSH-AuNPs platform also gave a much larger linear dynamic range (20–4000 pg mL^?1) than the SWNT system (40–150 pg mL^?1), but the SWNTs had 2-fold better sensitivity in the low pg mL^?1 range.     

Adsorption of Cr(VI) using cellulose microsphere-based adsorbent prepared by radiation-induced grafting

Cellulose microsphere (CMS) adsorbent was prepared by radiation-induced grafting of dimethylaminoethyl methacrylate (DMAEMA) onto CMS followed by a protonation process. The FTIR spectra analysis proved that PDMAEMA was grafted successfully onto CMS. The adsorption of Cr(VI) onto the resulting adsorbent was very fast, the equilibrium adsorption could be achieved within 15 min. The adsorption capacity strongly depended on the pH of the solution, which was attributed to the change of both the existed forms of Cr(VI) and the tertiary-ammonium group of PDMAEMA grafted CMS with the pH. A maximum Cr(VI) uptake (ca. 78 mg g^?1) was obtained as the pH was in the range of 3.0–6.0. However, even in strong acid media (pH 1.3), the adsorbents still showed a Cr(VI) uptake of 30 mg g^?1. The adsorption behavior of the resultant absorbent could be described with the Langmuir mode. This adsorbent has potential application for removing heavy metal ion pollutants (e.g. Cr(VI)) from wastewater.     

Column solid phase extraction and determination of ultra-trace Au,Pd and Pt in environmental and geological samples

A new sorbent based on cysteine modified silica gel (SiG-cys) was prepared and studied for preconcentration and separation of noble metals Au(III), Pd(II), Pt(II), Pt(IV). Its extraction efficiency was examined by batch and column solid phase extraction procedures. Laboratory experiments performed showed that sorbent is characterized with high selectivity, permiting quantitative sorption (93–97%) of noble metals Au, Pd and Pt from acidic media 0.1–2 mol L^? 1 HCl and unsignificant sorption (less than 2%) for common base metals like Cu, Fe, Mn and Zn. The analytes retained on the sorbent are effectively eluted with 0.1 mol L^? 1 thiourea in 0.1 mol L^? 1 HCl and measured by ETAAS or ICP OES under optimal instrumental parameters. The sorbent showed high mechanical and chemical stability and extraction efficiency was not changed after 500 cycles of sorption/desorption. The sorbent was successfully applied in analyticals procedures for preconcentration and determination of Au, Pd and Pt in geological and soil samples. Detection limits (3σ criteria) achieved, depending on the instrumental methods used are: ETAAS (0.005 μg L^? 1 for Au in river and sea water, 0.002 μg g^? 1 for Au in copper ore and copper concentrate); ICP OES (0.03 μg L^? 1 for Pd and 0.06 μg L^? 1 for Pt in river and sea water, 0.006 μg g^? 1 for Pd in copper ore and copper concentrate and 0.002 μg g^? 1 for soluble Pt in soil). The accuracy of the procedures developed was confirmed by added/found method for sea and river water; by the analysis of national certified materials (copper ore and copper concentrate for Au and Pd) and by determination of the sum of soluble Pt(II) + Pt(IV) in spiked soil samples.     

Polyaniline-nylon-6 electrospun nanofibers for headspace adsorptive microextraction

A headspace adsorptive microextraction technique was developed using a novel polyaniline-nylon-6 (PANI-N6) nanofiber sheet, fabricated by electrospinning. The homogeneity and the porosity of the prepared PANI-N6 sheet were studied using the scanning electron microscopy (SEM) and nanofibers diameters were found to be around 200 nm. The novel nanofiber sheet was examined as an extracting medium to isolate some selected chlorobenzenes (CBs), as model compounds, from aquatic media. The extracted analytes were desorbed using μL-amounts of solvent and eventually an aliquot of extractant was injected into gas chromatography–mass spectrometry (GC–MS). Various parameters affecting the extraction and desorption processes were optimized. The developed method proved to be convenient and offers sufficient sensitivity and a good reproducibility. Limits of detection achieved for CBs with the developed analytical procedure ranged from 19 to 33 ng L^?1, while limits of quantification were from 50 to 60 ng L^?1. The relative standard deviations (RSD) at a concentration level of 0.1 ng mL^?1 and 1 ng mL^?1 were in the range of 8–14% and 5–11% (n = 3), respectively. The calibration curves of analytes were investigated in the range of 50–1000 ng L^?1 and R² between 0.9739 and 0.9932 were obtained. The developed method was successfully applied to the extraction of selected CBs from tap and river water samples. The relative recovery (RR) percentage obtained for the spiked real water samples at 0.1 ng mL^?1 and 1 ng mL^?1 level were 93–103% and 95–104%, respectively. The whole procedure showed to be conveniently applicable and quite easy to handle.     

Flow-injection chemiluminescence determination of dihydralazine sulfate in serum using luminol and diperiodatocuprate (III) system

A novel flow-injection chemiluminescence (CL) method for the determination of dihydralazine sulfate (DHZS) is described. The method is based on the reaction of luminol and diperiodatocuprate (K₂[Cu(H₂IO₆)(OH)₂], DPC) in alkaline medium to emit CL, which is greatly enhanced by DHZS. The possible CL mechanism was first proposed based on the kinetic characteristic, CL spectrum and UV spectra. The optimum condition for the CL reaction was in detail studied using flow-injection system. The experiments indicated that under optimum condition, the CL intensity was linearly related to the concentration of DHZS in the range of 7.0 × 10^?9 to 8.6 × 10^?7 g mL^?1 with a detection limit (3σ) of 2.1 × 10^?9 g mL^?1. The proposed method had good reproducibility with the relative standard deviation 3.1% (n = 7) for 5.2 × 10^?8 g mL^?1 of DHZS. This method has the advantages of simple operation, fast response and high sensitivity. The special advantage of the system is that very low concentration of luminol can react with DPC catalyzed by DHZS to get excellent experiment results. And CL cannot be observed nearly when luminol with same concentration reacts with other oxidants, so luminol–DPC system has higher selectivity than other luminol CL systems. The method has been successfully applied to determine DHZS in serum.     

The removal of uranium (VI) from aqueous solutions onto natural sepiolite

The adsorption of uranium (VI) from aqueous solutions onto natural sepiolite has been studied using a batch adsorber. The parameters that affect the uranium (VI) sorption, such as contact time, solution pH, initial uranium(VI) concentration, and temperature, have been investigated and optimized conditions determined. Equilibrium isotherm studies were used to evaluate the maximum sorption capacity of sepiolite and experimental results showed this to be 34.61 mg · g^?1. The experimental results were correlated reasonably well by the Langmuir adsorption isotherm and the isotherm parameters (Q_o and b) were calculated. Thermodynamic parameters (ΔH° = ?126.64 kJ · mol^?1, ΔS° = ?353.84 J · mol^?1 · K^?1, ΔG° = ?21.14 kJ · mol^?1) showed the exothermic heat of adsorption and the feasibility of the process. The results suggested that sepiolite was suitable as sorbent material for recovery and adsorption of uranium (VI) ions from aqueous solutions.     

Thermodynamics of the Cu(II) adsorption on thin vanillin-modified chitosan membranes

In this work, low-density vanillin-modified thin chitosan membranes were synthesized and characterized. The membranes were utilized as adsorbent for the removal of Cu(II) from aqueous solutions. The experimental data obtained in batch experiments at different temperatures were fitted to the Langmuir and Freundlich isotherms to obtain the characteristic parameters of each model. The adsorption equilibrium data fitted well with the Langmuir model (average R² > 0.99). Interactions thermodynamic parameters (Δ_intH, Δ_intG, and Δ_intS), as well as the interaction thermal effects (Q_int) were determined from T = (298 to 333) K. The thermodynamic parameters, the Dubinin–Radushkevick equation and the comparative values of Δ_intH for some Cu(II)–adsorbent interactions suggested that the adsorption of Cu(II) ions to vanillin-chitosan membranes show average results for both the diffusional (endothermic) and chemical bonding (exothermic) processes in relation to the temperature range studied.     

Metal adsorbent for alkaline etching aqua solutions of Si wafer

High performance adsorbent is expected to be synthesized for the removal of Ni and Cu ions from strong alkaline solution used in the surface etching process of Si wafer. Fibrous adsorbent was synthesized by radiation-induce emulsion graft polymerization onto polyethylene nonwoven fabric and subsequent amination. The reaction condition was optimized using 30 L reaction vessel and nonwoven fabric, 0.3 m width and 18 m long. The resulting fibrous adsorbent was evaluated by 48 wt% NaOH and KOH contaminated with Ni and Cu ions, respectively. The concentration levels of Ni and Cu ions was reduced to less than 1 μg/kg (ppb) at the flow rate of 10 h^?1 in space velocity. The life of adsorbent was 30 times higher than that of the commercialized resin. This novel adsorbent was commercialized as METOLATE^® since the ability of adsorption is remarkably higher than that of commercial resin used practically in Si wafer processing.     

Novel luminescent nanoparticles for DNA detection

Highly luminescent LaF₃:Ce³⁺/Tb³⁺ nanocrystals were successfully prepared and surface functionalized via Layer-by-Layer technology. These as-prepared nanocrystals are highly resistant to photobleaching and pretty dispersible in aqueous solution. Due to the efficient luminescence quenching of the nanocrystals by nucleic acids, a facile fluorescence quenching method was developed for the detection of trace amount of nucleic acids. Under optimal conditions, the fluorescence intensity was proportional to the DNA concentration over the range of 0.60–25.0 μg mL^?1 for calf thymus DNA (ct-DNA) and 0.60–30.0 μg mL^?1 for herring sperm DNA (hs-DNA), respectively. The corresponding detection limit is 0.21 μg mL^?1 for ct-DNA and 0.31 μg mL^?1 for hs-DNA, respectively. The results indicated that the reported method is simple and rapid with wide linear range. Also, the recovery and relative standard deviation of this method are reasonable and satisfactory.     

Biodegradable metal adsorbent synthesized by graft polymerization onto nonwoven cotton fabric

A fibrous adsorbent for Hg ions was synthesized by radiation-induced emulsion graft polymerization of glycidyl methacrylate (GMA) onto a nonwoven cotton fabric and subsequent chemical modification. The optimal pre-irradiation dose for initiation of the graft polymerization of GMA, which minimized the effects of radiation damage on the mechanical strength of the nonwoven cotton fabric, was found to be 10 kGy. The GMA-grafted nonwoven cotton fabric was subsequently modified with ethylenediamine (EDA) or diethylenetriamine (DETA) to obtain a Hg adsorbent. The resulting amine-type adsorbents were evaluated for batch and continuous adsorption of Hg. In batch adsorption, the distribution coefficients of Hg reached 1.9×10⁵ and 1.0×10⁵ for EDA- and DETA-type adsorbents, respectively. A column packed with EDA-type adsorbent removed Hg from 1.8 ppm Hg solution at a space velocity of 100 h^?1, which corresponds to 16,000 times the volume of the packed adsorbent. The adsorbed Hg on the EDA-type adsorbent could be completely eluted by 1 M HCl solution. A microbial oxidative degradation test revealed that the EDA-type adsorbent is biodegradable.     

Sensitive liquid chromatography–tandem mass spectrometry method for the determination of pantoprazole sodium in human urine

A sensitive and selective liquid chromatographic–tandem mass spectrometric (LC–MS–MS) method was developed to determine pantoprazole sodium (PNT) in human urine. After solid-phase extraction with SPE cartridge, the urine sample was analysed on a C₁₈ column (symmetry 3.5 μm; 75 mm × 4.6 mm i.d) interfaced with a triple quadrupole tandem mass spectrometer. Positive electrospray ionization was employed as the ionization source. The mobile phase consisted of acetonitrile–water (90:10, v/v). The method was linear over a concentration range of 1–100 ng mL^?1. The lower limit of quantitation was 1 ng mL^?1. The intra-day and inter-day relative standard deviation across three validation runs over the entire concentration range was <10.5%. The accuracy determined at three concentrations (8.0, 50.0 and 85.0 ng mL^?1 PNT) was within ±1.25% in terms of relative errors.     

Determination of sulfonamides in food samples by membrane-protected micro-solid phase extraction coupled with high performance liquid chromatography

In the present study, a simple and sensitive extraction method based on polypropylene membrane-protected micro-solid phase extraction (MP-μ-SPE) has been developed for analysis of sulfonamides in food samples. Poly (methacrylic acid-ethylene glycol dimethacrylate) (p-MAA-EDMA) was synthesized using orthogonal array experimental design, optimized with three factors at four levels and evaluated on yield, hydrophobic and cation-exchange properties. The optimized p-MAA-EDMA was then employed as the sorbent in the MP-μ-SPE for extraction of sulfonamides from milk and chicken muscle samples, followed by high performance liquid chromatographic analysis with ultraviolet detection. Under optimized extraction conditions, good linearities (0.010–1.0 μg mL^?1 with r² > 0.9900), low limits of detection (0.38–0.62 ng mL^?1), and acceptable intra-day (2.7–13.7%) and inter-day (6.7–15.2%) relative standard deviations were obtained. It was demonstrated to be an effective approach to handle semi-solid/solid samples with good resistance to interference from “dirty” samples.