CeO2-Al2O3负载金催化剂用于水煤气变换反应的催化活性

采用浸渍法和沉积 沉淀法制备了CeO₂-Al₂O₃复合氧化物,比较了复合氧化物负载纳米金催化剂对水煤气变换反应的催化活性。通过N2物理吸附、XRD、TEM、H₂-TPR等表征手段对复合氧化物及其负载金催化剂的物相和结构进行分析,发现复合氧化物的制备方法及其焙烧温度对其比表面积、孔结构及水煤气变换反应活性有明显的影响。与沉积 沉淀法相比,浸渍法制备的CeO₂-Al₂O₃复合氧化物具有较大的CeO₂晶粒尺寸,经500℃焙烧后再负载金,所得催化剂具有更高的活性,250℃时CO转化率可达78.1%。     

焙烧温度对CuO/γ-Al2O3和CeO2-CuO/γ-Al2O3催化剂NO还原活性的影响

用浸渍法制备了CuO/γ-Al2O3催化剂和CeO2改性的CeO2-CuO/γ-Al2O3催化剂,考察了焙烧温度对CuO/γ-Al2O3和CeO2-CuO/γ-Al2O3催化剂C3H6还原NO反应活性的影响,以及CeO2的添加量对CeO2-CuO/γ-Al2O3催化剂C3H6还原NO反应活性的影响。结果表明,在200 ℃～500 ℃的焙烧温度范围内,焙烧温度对CuO/γ-Al2O3催化剂的活性影响很小；在500 ℃～800 ℃的焙烧温度范围内,随着焙烧温度的升高CuO/γ-Al2O3催化剂的活性急剧下降,由XRD物相测定结果可知,归因于对反应表现惰性的尖晶石CuAl2O4相的生成。当焙烧温度为500 ℃时,CeO2的添加对CuO/γ-Al2O3催化剂的活性影响很小；当焙烧温度为800 ℃时,CeO2的添加对CuO/γ-Al2O3催化剂有明显的助催化作用,当Ce和Cu的摩尔比为1∶10时,NO转化率较为理想。     

Co/γ-Al2O3催化剂上CO氧化反应的研究

以浸渍法与沉积沉淀法制备了不同Co负载量的Co／γ-Al2O3催化剂，研究了对CO的催化氧化行为,考察了Co含量，焙烧温度，反应温度等对催化剂氧化性能的影响，结果表明，沉积沉淀法制备400℃焙烧的负载量为10％的Co／γ-Al2O3在90℃就能够实现CO完全氧化，且热稳定性比浸渍法制得催化剂好．本文还采用XRD、TPR、XPS等技术，分别研究了Co／γ-Al2O3样品的晶相结构，还原性能及表面化学状态.XRD结果表明，以硝酸盐为前驱物的Co负载于γ-Al2O3后，Co主要以Co3O4结构存在，反应的活性相Co3O4的生成有利于CO催化氧化，且以不同制备方法得到的样品中Co3O4晶粒大小不同，催化活性也不同．TPR结果表明，以沉积沉淀法制备催化剂的还原峰向低温移动，CoOx的还原更加容易．XPS表面分析表明沉淀法制备的Co／γ-Al2O3样品中，Co3O4在载体表面富集．     

Au/CeO2催化剂的制备及其对CO催化氧化性能的研究

采用水溶液沉淀法和沉积-沉淀法分别制备了CeO2载体及相应Au/CeO2催化剂,以CO氧化反应为表征反应,考察了载体制备条件,催化剂的焙烧温度、预处理温度和气氛以及活性组分负载量对催化剂性能的影响,并对催化剂进行了BET、XRD和TEM表征,分析了影响催化剂活性的原因.结果表明,载体的制备条件对催化剂的活性有一定影响,经微波处理的载体负载活性组分后,由于活性组分和载体的接触较紧密,因此有利于催化剂活性的提高.催化剂的最佳焙烧温度为300℃,最佳活化温度为300℃,气氛为空气,最佳金负载量为4%.     

Ni／ZrO2-Al2O3制备表征及催化性能的研究

本文采用浸渍沉淀法制备了不同配比的ZrO2-Al2O3复合载体。并通过浸渍法制备Ni/ZrO2-Al2O3催化剂,以苯加氢制环己烷反应为探针,考察了ZrO2与Al2O3的配比对Ni催化剂催化加氢性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、程序升温脱附(TPD)等技术考察复合载体对Ni催化剂的体相结构、还原性能以及表面吸附性能的影响。研究结果表明,ZrO2质量分数为20%的复合载体所负载的Ni催化剂有很好的加氢活性,优于单组分载体负载的Ni催化剂;采用浸渍沉淀法制备的ZrO2-Al2O3复合载体中ZrO2以非晶态形式存在,这是由于Al2O3的存在影响了ZrO2的内部结构;该载体负载的Ni催化剂较其他催化剂更容易被还原,吸附中心数量增加。     

Au/Ce1-xZrxO2催化剂的制备、表征及其在CO氧化和水煤气变换反应中的催化性能

采用共沉淀法制备了不同锆铈摩尔比的Ce1-xZrxO2(x=0,0.1,0.3,0.5,0.7,0.9和1.0)氧化物,并以改性的浸渍法制备了金担载量为1%(质量分数)的Au/Ce1-xZrxO2催化剂.考察了催化剂在低温CO氧化和水煤气变换反应中的催化性能.应用氮物理吸附、X射线衍射、透射电镜和H2程序升温还原等技术对氧化物载体及其负载金催化剂进行了表征,并与其催化性能进行了关联.结果表明,与纯CeO2和ZrO2相比,Ce1-xZrxO2的比表面积增大而孔径减小,孔分布更加集中.Zr的加入使表面Ce4 的还原更加困难,使体相Ce4 的还原更加容易.活性组分金的加入有利于铈锆氧化物的还原.ZrO2载体较大的孔径使金在载体表面分散均匀而粒子较小,因此与Au/CeO2和Au/Ce1-xZrxO2相比,Au/ZrO2具有更好的低温CO氧化活性和水煤气变换活性,而Au/CeZrO在高温下的水煤气变换反应中表现出更好的催化性能.     

Pt/CexZr1-xO2催化剂上丙烷完全氧化性能研究

采用沉淀法制备了ZrO2,CeO2和Ce0.7Zr0.3O2载体,并用浸渍法制备负载型Pt催化剂。考察了500和900℃焙烧催化剂的丙烷完全氧化性能和水汽对丙烷氧化反应的影响。对于500℃焙烧的催化剂,催化剂的丙烷氧化活性顺序为:Pt/ZrO2-500>Pt/CeO2-500>Pt/Ce0.7Zr0.3O2-500;而经900℃焙烧的催化剂活性顺序为:Pt/ZrO2-900>Pt/Ce0.7Zr0.3O2-900>Pt/CeO2-900。反应气氛中水汽的存在对两种Pt/ZrO2催化剂的活性均有抑制作用(T50温度均提高了10~15℃);而对于Pt/CeO2-500催化剂有抑制作用(T50温度提高10℃),但对Pt/CeO2-900催化剂活性有促进作用(T50温度下降25℃);对于两种Pt/Ce0.7Zr0.3O2催化剂活性具有促进作用(T50温度均下降5~25℃)。表征结果表明催化剂的活性与其表面Pt物种价态密切相关,催化剂表面上Pt0物种有利于活性的提高。Pt/Ce0.7Zr0.3O2-500催化剂中只含有氧化态Pt物种(Pt^2+),而Pt/Ce0.7Zr0.3O2-900催化剂中则含有部分金属态Pt物种,因此其活性高于Pt/Ce0.7Zr0.3O2-500催化剂。     

改性沉积-沉淀法制备Au/Fe2O3水煤气变换反应催化剂

采用共沉淀法、沉积-沉淀法和改性沉积-沉淀法制备了Au/Fe2O3催化剂,运用N2吸附、X射线衍射、X射线光电子能谱和透射电镜等技术对其进行了表征,考察了制备方法对Au/Fe2O3催化剂水煤气变换反应催化活性的影响.结果表明,改性沉积-沉淀法制备的催化剂具有最好的催化活性,150℃时CO转化率达82.3%.该催化剂比表面积较大,金粒子尺寸(3~5nm)较小且分布均匀.载体氧化铁以无定形态和结晶态共存,金与载体间存在较强的相互作用,这对催化剂活性的提高起着重要作用.     

(CeO_2-ZrO_2-Al_2O_3)-(La_2O_3-Al_2O_3)复合氧化物负载的Pd密偶催化剂:载体焙烧温度的影响

采用同时共沉淀法制备了(CeO2-ZrO2-Al2O3)-(La2O3-Al2O3)新型复合氧化物(CZA-LA),考察了焙烧温度对CZA-LA负载的Pd密偶催化剂的影响,并采用N2吸附-脱附法和X射线衍射对其进行了表征.结果表明,随着焙烧温度的升高,尽管CZA-LA样品的比表面积降低,但即使在1000°C焙烧5h后,其比表面积仍能保持在122m2/g左右;另外,CZA-LA样品的孔体积降低幅度不大,当在700℃及更高温度下焙烧后基本上保持稳定.以不同温度焙烧5h后的样品为载体,采用等体积浸渍法制备了一系列整体式Pd/CZA-LA密偶催化剂(Pd含量2.0g/L).催化剂对消除模拟汽油车尾气中C3H8活性测试结果表明,各新鲜催化剂的活性相差不大,均具有较低的起燃温度T50和完全转化温度T90.当催化剂经老化处理后,以1000°C焙烧的载体负载的Pd催化剂活性最高,T50和T90分别为310和341℃,ΔT仅为31℃,仅比新鲜催化剂的高7℃.可见,该催化剂表现出优异的催化活性和抗老化性能,可以满足欧Ⅳ及更高标准的用于汽油车尾气净化的密偶催化剂的性能要求.     

超声浸渍法制备Pd/Al2O3催化剂及其催化蒽醌加氢性能

 以球形 γ-Al2O3 和 θ-Al2O3 为载体,分别采用超声浸渍和普通浸渍方法制备了Pd含量为0.3%的负载型催化剂,并将其用于蒽醌加氢反应. 采用X射线衍射、 N2吸附和透射电镜等手段对催化剂的理化性质和孔结构进行了分析,考察了浸渍方法对催化剂活性金属分散度的影响. 结果表明,与普通浸渍法相比,超声浸渍法制备的负载型Pd催化剂金属分散度明显提高,因而对蒽醌加氢反应表现出较高的催化活性. 以960 ℃焙烧的球θ-Al2O3 为载体,通过超声浸渍制备的负载型Pd催化剂具有较高的Pd分散度和较大的孔径,在蒽醌加氢反应中对反应物的扩散阻力较小,因而表现出更高的催化活性,而且反应中催化剂的稳定性良好.     

Determination of stoichiometry of vanadium oxides by 14-MeV neutron activation

A method was developed for the determination of oxygen/vanadium ratios in vanadium oxides by 14-MeV neutron activation analysis by means of the reactions ⁵¹V(n, p)⁵¹Ti and ¹⁶O(n, p)¹⁶N. A linear relationship between activity ratios and weight ratios of six mixtures composed of vanadium carbide and oxalic acid was obtained with a precision of 0.18% after suitable corrections for /gg- and β-ray absorption. Four commercial vanadium oxides and three specially prepared vanadium oxides were analyzed. The V/O ratio varied between 1.980 and 3.015. The percent standard deviation on these values was between 0.53% and 1.09%.     

An investigation on characterization and thermal analysis of the Aughinish red mud

Summary Red mud is insoluble, fine-grained waste residue which is generated as a by product during the production of alumina from the Bayer process. In this article, the thermal behavior of Aughinish red mud was investigated using thermal gravimetric analysis (TG) and differential thermal analysis (DTA). For identification of oxide and mineral phases in the red mud sample, XRD method, scanning electron microscopy (SEM), EDAX were used. Iron (30.4%), aluminium (23.6%) and titanium (17.85%) oxides are major oxides in the sample. Two endothermic peaks were shown on DTA curve. The total mass loss in the red mud was found to be 10.1%, which was associated with moisture and water molecules in gibbsite and boehmite phases.     

富氢气氛下CeO_2-NiO纳米棒催化剂的CO选择性氧化性能研究

采用水热法制备了一系列不同Ce/Ni物质的量比的纳米棒CeO_2(x)-NiO催化剂。运用低温N_2吸附-脱附、XRD、TEM、拉曼光谱、H_2-TPR及XPS等技术对催化剂的形貌、结构进行了表征。考察了Ce/Ni物质的量比对CeO_2(x)-NiO催化剂形貌及富氢气氛下CO选择性氧化(CO PROX)反应性能的影响。TEM测试结果表明,调变Ce/Ni物质的量比可制得不同粒径的CeO_2(x)-NiO纳米棒催化剂。H_2-TPR测试结果表明,将NiO掺入CeO_2可提升Ce O_2(x)-NiO催化剂的氧化还原能力。拉曼光谱及XPS测试结果表明,镍含量较低时,CeO_2(x)-NiO催化剂表面活性氧物种及氧空位含量均较多,利于提升其催化性能。CO PROX催化性能测试结果显示,镍含量较低的CeO_2(0.89)-NiO纳米棒催化剂的活性和选择性最好,在170-220℃的反应条件下,CO转化率为100%,CO_2选择性为52%。     

Analysis of non-conducting powders by direct current glow discharge atomic emission spectrometry and application to the determination of rare earth elements

Some characteristics for the analysis of non-conducting powders by direct current glow discharge atomic emission spectroscopy (dc-GD-AES) were investigated. Copper powder was chosen as a suitable host conducting material for the analysis of mixtures of rare earth oxides. The influences of sample preparation and discharge parameters on the sputtering rate, discharge stability and emission intensity of the analyte were investigated systematically. The sample-to-sample reproducibility was discussed, and the average RSDs were in the range from 4% to 5%. The proposed method was applied to the analysis of a mixture of rare earth oxides and the results obtained were in good agreement with those obtained by ICP-AES.     

Ti-Si mixed oxides prepared by polymer in situ sol-gel chemistry with the aid of CO2

A method to prepare titania-silica binary oxides is proposed in this work. In this route, inorganic precursors tetraethyl orthosilicate (TEOS) and titanium isopropoxide (TIP) were simultaneously or sequentially impregnated into a polypropylene (PP) matrix using supercritical carbon dioxide as a swelling agent and carrier. Hydrolysis and condensation reaction of the precursors confined in a polymer network were induced by treating the composites in 1 mol.dm(-3) (1 M) HCl. Then the PP matrix was decomposed at higher temperature, and titania-silica binary oxides were obtained. The mixed oxides were characterized by X-ray diffraction and Raman, FTIR, and X-ray photoelectron spectroscopy. It was demonstrated that the structure of the oxides depended strongly on the procedure to impregnate the precursors. The simultaneous method, in which the TEOS and TIP were simultaneously impregnated into a PP matrix, resulted in mixed oxides with highly dispersed titanium oxide species in the SiO2 matrix, while the sequential method produced the mixed oxide with separate SiO2 and TiO2 phases which were connected by Ti-O-Si bands at the interface. The method described in this work provides a new route to control the texture of TiO2-SiO2 mixed oxide simply by the impregnation sequence.     

Role of the Acidic-basic Characters of Some Metal Oxides in the Pyrolysis of Ammonium Perchlorate

Six metal oxide samples were prepared by calcination of the corresponding precursors at 500°C for 5 h in air and were characterized by IR and XRD analyses. Their surface areas were calculated by means of the BET method. The acidities and basicities of these metal oxides were estimated thermogravimetrically by the method of adsorption of pyridine and formic acid as probe molecules. The pyrolyses of pure ammonium perchlorate (AP) and of AP mixed with (10% w/w) metal oxide were studied, in a dynamic atmosphere of N₂, by thermogravimetric analysis (TG) and derivative thermogravimetric analysis. A correlation was found between the catalytic activities of the metal oxides during the pyrolysis of AP, and their acidic-basic characters. The activation energies of the non-catalyzed and catalyzed pyrolysis of AP were calculated from the TG results via the Coats-Redfern equation. This revised version was published online in July 2006 with corrections to the Cover Date.     

液相色谱–大气压化学电离串联质谱法测定油脂中9种胆固醇氧化物

建立一种准确测定油脂中9种胆固醇氧化物含量的同位素稀释液相色谱-串联质谱测定方法。向油脂样品中加入无水乙醇和60%氢氧化钾溶液,在室温下避光皂化22 h,使用乙醚-石油醚混合液(1∶1)作为提取溶液,采用液-液萃取方式提取目标物,再使用硅胶柱进行净化,采用5 mmol/L乙酸铵溶液与甲醇-乙腈混合液(1∶1)为双流动相梯度淋洗,使用Agilent ZORBAX SB-C18色谱柱分离,在大气压化学电离(APCI)正离子模式下,采用多反应监测模式内标法定量测定。在10~500μg/L范围内,9种胆固醇氧化物的质量浓度与色谱峰面积线性良好,相关系数(r2)均大于0.995,检出限均为0.5 mg/kg,在1,5 mg/kg两个添加水平时,加标回收率为71.2%~94.4%,相对标准偏差小于10%(n=6)。该方法满足动植物油脂中胆固醇氧化物含量测定需要。     

Development and optimization of magnetic technologies based processes for removal of some toxic heavy metals

In the developing countries where the cost is often a decisive factor, extensive studies were undertaken to test the most effective factors on the preparation, optimization and validation of the magnetic particles (or, more accurately, magnetizable particles) for removal of heavy metals from wastewaters. The objective of the proposed work was focused to provide promising solid-phase materials, which, are relatively in expensive and combine high surface capacity with fast efficient treatment. Four various metal oxides including hydrous ferric oxide (HFO), hydrous stannic oxide (HSO) and mixed ferric/stannic oxide (HMO), were prepared by precipitation with ammonia from metal chloride solutions. Two mixed oxides were prepared with different Sn/Fe ratios of 50% and 20%. Optimal conditions for the activation of these particles and the subsequent mixing of various metals oxides are tested together with the utility of the method to get a new composite material with developed chemical characteristics over their individual metal oxides. Factors affecting the sorption behavior of the prepared samples in basic and acid media were elucidated. The magnetic treatment procedure using the mixed oxide (50%) enables the equilibration step to be carried out rapidly mainly due to ferric oxide during the magnetization process and efficiently due to high capacity of the stannic oxide. A key factor in achieving very high uptake percentage is the reduction of non-specific binding of various heavy metals to the solid phase support. This is usually achieved by increasing the ion exchange capability, in addition to their adsorption process.     

钌钛复合氧化物载Pd催化剂的制备及对甲酸氧化的电催化性能

用TiN浸渍热分解法制备了不同摩尔比的钉钛复合氧化物(Rux Ti1-x O2)纳米粉体,并以此为载体,用微波还原法制备了用作直接甲酸燃料电池(DFAFC)阳极催化的钯催化剂(Pd/Rux Ti1-x O2,Pd的质量分数20%).X射线能谱(EDS)、X射线衍射(XRD)和透射电镜(TEM)测试结果表明,Pd纳米颗粒...