Analytical methodologies for determining the occurrence of endocrine disrupting chemicals in sewage treatment plants and natural waters

In this study, a method for assessing the occurrence of trace amounts of 12 representative estrogenic compounds in sewage and surface waters was developed. The selected substances were the phytoestrogens daidzein, genistein and biochanin A, the alkylphenols bisphenol A and 4-nonylphenol, the natural hormones 17β-estradiol, estrone, estriol and the synthetic hormone 17α-ethynylestradiol and the mycoestrogens zearalenone and two of its metabolites (α-zearalanol and β-zearalanol). The procedure consists in solid phase extraction (SPE) performed with OASIS cartridges followed by liquid chromatography coupled with tandem mass spectrometry (LC-MS-MS). Recoveries were all above 80% for each analyzed aqueous matrices. The developed method was applied to verify the occurrence of endocrine disrupters in environmental samples of sewage influents and effluents of an Italian STP. Phytoestrogens were present in effluents at concentrations ranging from 3 to 83 ng/l, whereas the levels detected for alkylphenols were in the range 13-36 ng/l for bisphenol A and up to 1 μg/l for nonylphenol. Estrogens and zeranols were determined at levels below 30 ng/l. Analysis of a river (Tiber) receiving effluent waters revealed high quantities of bisphenol A (15-29 ng/l) and nonylphenol (up to 1.2 μg/l), whereas the presence of all the other compounds were at levels of few ng/l.     

LC/MS and LC/MS/MS based protocol for identification of dyes in historic textiles

Identification of dyes in historic textiles was until recently only based on reversed phase liquid chromatography and diode-array detection (RPLC–DAD). Although in the last years mass spectrometry (MS) is increasingly used as a detection system for liquid chromatography, most applications in the field are directed to identification of the molecular ions or in studies dedicated to degradation products which may be used as markers in RPLC–DAD. In the present work, an analytical protocol for the identification of dyes using RPLC/ESI/MS is presented. Atmospheric pressure electrospray ionization (ESI) was applied, in the negative ion monitoring mode. Both single stage and tandem MS (MS/MS) approaches were considered. An ion trap was used as mass analyzer. Experiments are based on the characterization of standards (natural dyes and/or dyed fibers) with the mass spectrometer sequentially working in the following modes: single MS/full scan, followed by plotting chromatograms through ion extraction (IEC) according to mass/charge ratios corresponding to molecular ions; single MS/selected ion monitoring (SIM) mode; tandem MS/single reaction monitoring (SRM) mode; tandem MS/multiple reactions monitoring (MRM) or product ion scanning modes. A faster chromatographic separation could be applied as MS detection readily balanced the selectivity of the analytical process. In a case study, 11 dyes from 3 biological sources were detected in a 0.5 mg historic sample.     

Determination of various estradiol mimicking-compounds in sewage sludge by the combination of microwave-assisted extraction and LC-MS/MS

In this work, we present the development and application of a microwave assisted extraction followed by liquid chromatography-tandem mass spectrometry methodology (MAE-LC-MS/MS) for the determination of various estradiol-mimicking compounds in sewage sludge samples. For the purification of the MAE extracts, we have employed a solid phase extraction (SPE) clean-up procedure, previously optimised. The entire method provides recoveries between 71.7% and 103.1%, with relative standard deviation lower than 11.1% and limits of detection ranging from 0.6 to 3.5 ng g⁻¹. The developed method was applied to samples from three wastewater treatment plants (WWTPs) located in Las Palmas of Gran Canaria (Spain), two of which had a conventional activated sludge treatment (AST), whereas the third treatment plant had an advanced membrane bioreactor treatment (MBR). All of the analytes in the study, including (nonylphenol (NP), octylphenol (OP), and some of their ethoxylated chains AP_nEOs (n ≤ 7), 17β-estradiol (E2), estriol (E3), 17α-ethynylestradiol (EE) and bisphenol-A (BPA)), were found in almost all samples in concentrations ranging from 0.9 to 710.2 ng g⁻¹.     

On‐line solid‐phase extraction for liquid chromatography–mass spectrometry analysis of pesticides

Public concern about pesticides in food and water has increased dramatically in the last two decades. In order to guarantee consumers’ health and safety, analytical methods that could provide fast and reliable answers without compromising accuracy and precision are required. Sample treatment is probably the most tedious and time‐consuming step in many analytical procedures and, despite the significant advances in chromatographic separations and mass spectrometry techniques, sample treatment is still one of the most important parts of the analytical process for achieving good analytical results. Therefore, over the last years, considerable efforts have been made to simplify the stage and to develop fast, accurate, and robust methods that allow the determination of a wide range of pesticides without compromising the integrity of the extraction process. This review article intends to give a short overview of recently developed on‐line solid‐phase extraction, preconcentration, and clean‐up procedures for the determination of pesticides in complex matrices by liquid chromatography–mass spectrometry techniques.     

On-line solid phase extraction LC-MS/MS analysis of pharmaceutical indicators in water: A green alternative to conventional methods

A method using automated on-line solid phase extraction (SPE) directly coupled to liquid chromatography/tandem mass spectrometry (LC-MS/MS) has been developed for the analysis of six pharmaceuticals by isotope dilution. These selected pharmaceuticals were chosen as representative indicator compounds and were used to evaluate the performance of the on-line SPE method in four distinct water matrices. Method reporting limits (MRLs) ranged from 10 to 25 ng/L, based on a 1 mL extraction volume. Matrix spike recoveries ranged from 88 to 118% for all matrices investigated, including finished drinking water, surface water, wastewater effluent and septic tank influent. Precision tests were performed at 50 and 1000 ng/L with relative standard deviations (RSDs) between 1.3 and 5.7%. A variety of samples were also extracted using a traditional off-line automated SPE method for comparison. Results for both extraction methods were in good agreement; however, on-line SPE used approximately 98% less solvent and less time. On-line SPE coupled to LC-MS/MS analysis for selected indicators offers an alternative, more environmentally friendly, method for pharmaceutical analysis in water by saving time and costs while reducing hazardous waste and potential environmental pollution as compared with off-line SPE methods.     

Determination of antimicrobial residues and metabolites in the aquatic environment by liquid chromatography tandem mass spectrometry

Antimicrobials are used in large quantities in human and veterinary medicine. Their environmental occurrence is of particular concern due to the potential spread and maintenance of bacterial resistance. After intake by the organisms, the unchanged drug and its metabolized forms are excreted and enter wastewater treatment plants where they are mostly incompletely eliminated, and are therefore eventually released into the aquatic environment. The reliable detection of several antimicrobials in different environmental aqueous compartments is the result of great improvements achieved in analytical chemistry. This article provides an overview of the more outstanding analytical methods based on liquid chromatography tandem mass spectrometry, developed and applied to determine antimicrobial residues and metabolites present in surface, waste, and ground waters.      

Dual gradient LC method for the determination of pharmaceutical residues in environmental samples using a monolithic silica reversed phase column

Detailed below is a simple reversed-phase liquid chromatography (RP-LC) method for the simultaneous separation of up to 21 acidic, basic, and neutral pharmaceuticals using Merck Chromolith Performance RP-C18e monolithic columns with direct ultraviolet (UV) absorption detection. By simultaneously applying a solvent elution gradient program with a mobile phase flow gradient, both a decrease in the overall analysis time and a general increase in peak efficiencies were observed. Mobile phase pH and buffer concentration were optimised using the overall resolution product under applied gradient conditions. Under optimised conditions peak area reproducibility (n?=?6) ranged between 0.4 and 9.3%, determined at the method LOQ level. For real sample analysis pharmaceutical residues were extracted using an optimised solid phase extraction (SPE) procedure, utilising Strata-X extraction cartridges, which overall provided the highest relative recovery data in comparison with four other commercially available SPE sorbents (17 out of 20 residues investigated had recoveries over 70%). Complete method precision, including all sample pre-treatment and LC analysis for six spiked river water samples at the 1 and 2?µg?L^?1 level was between 10 and 29%. Using 1?L volumes of 1?µg?L^?1 spiked estuarine water samples, the majority of detection limits were found to be in the 10–50?ng?L^?1 range.     

Trace-level determination of pharmaceutical residues by LC-MS/MS in natural and treated waters. A pilot-survey study

A pilot-survey study was performed by collecting samples (influent and effluent wastewaters, rivers and tap waters) from different locations in Europe (Spain, Belgium, Germany and Slovenia). A solid-phase extraction (SPE) followed by liquid chromatography–tandem mass spectrometry method was applied for the determination of pharmaceuticals (ibuprofen, naproxen, ketoprofen, diclofenac and clofibric acid). Method detection limits and method quantification limits were at the parts-per-trillion level (7.5–75 ng/L). The recovery rates of the SPE from deionized water and effluent wastewater samples spiked at 100- and 1,000-ng/L levels ranged from 87 to 95%. Identification criteria in compliance with the EU regulation for confirmatory methods of organic residues were applied. A detailed study of signal suppression evaluation for analysis of pharmaceutical residues in effluent wastewaters is presented.     

Rapid analysis of three β‐agonist residues in food of animal origin by automated on‐line solid‐phase extraction coupled to liquid chromatography and tandem mass spectrometry

An automated online solid‐phase extraction with liquid chromatography and tandem mass spectrometry method was developed and validated for the detection of clenbuterol, salbutamol, and ractopamine in food of animal origin. The samples from the food matrix were pretreated with an online solid‐phase extraction cartridge by Oasis MCX for <5 min after acid hydrolysis for 30 min. The peak focusing mode was used to elute the target compounds directly onto a C₁₈ column. Chromatographic separation was achieved under gradient conditions using a mobile phase composed of acetonitrile/0.1% formic acid in aqueous solution. Each analyte was detected in two multiple reaction monitoring transitions via an electrospray ionization source in a positive mode. The relative standard deviations ranged from 2.6 to 10.5%, and recovery was between 76.7 and 107.2% at all quality control levels. The limits of quantification of three β‐agonists were in the range of 0.024–0.29 μg/kg in pork, sausage, and milk powder, respectively. This newly developed method offers high sensitivity and minimum sample pretreatment for the high‐throughput analysis of β‐agonist residues.     

Combining microwave-assisted extraction and liquid chromatography–ion-trap mass spectrometry for the analysis of hexabromocyclododecane diastereoisomers in marine sediments

An efficient microwave-assisted extraction (MAE) procedure coupled with high performance liquid chromatography–electrospray-ion-trap mass spectrometry (HPLC–ESI-ITMS) has been evaluated to determine hexabromocyclododecane diastereoisomers (α-, β- and γ-HBCD) in marine sediments. The composition of the LC mobile phase (consisting of water, methanol and acetonitrile) and the parameters of electrospray ionization (ESI) were evaluated to obtain chromatographic baseline separation and high sensitivity for the detection of these diastereoisomers. The effects of various operating parameters on the quantitative extraction of the HBCDs through MAE were systematically investigated. The three diastereoisomers were then quantitated by HPLC–ITMS employing ESI operated in the negative ionization mode. The HBCDs were extracted from the sediments through MAE using 40 mL of acetone/n-hexane (1/3, v/v) at 90 °C for 12 min. The limits of quantitation (LOQ) ranged from 25 to 40 pg/g (dry weight) in 5 g of the sediment samples. The recoveries of the HBCDs in spiked sediment samples ranged from 68 to 91% (relative standard derivation: 2–11%). The extraction efficiency of the MAE technique was also compared with Soxhlet extraction and pressurized liquid extraction.     

Liquid chromatography-tandem mass spectrometric analysis and regulatory issues of polar pesticides in natural and treated waters

Pesticides are among the most detected contaminants in the aquatic environment. This is mainly due to their use in agriculture and their physico-chemical properties that enable transportation and a persistent or pseudo-persistent existence in the water media. Several directives and guidelines set maximum levels of pesticides in water in order to protect the human and environmental health. A brief discussion of the existing directives and guidelines concerning pesticides in water is presented, e.g., the new regulatory framework for the Registration, Evaluation and Authorisation of Chemicals (REACH), and the Directive 91/414/EEC concerning the placing of plant protection products on the market. Up-to-date analytical tools to support the REACH program are of prime importance to ensure its complete implementation. Since liquid chromatography (LC) coupled to mass spectrometry (MS) is considered the most appropriate technique for determination of most modern pesticides in environmental waters, the most recent developments and applications in this field are discussed in detail in this review.     

Evaluation of various QuEChERS based methods for the analysis of herbicides and other commonly used pesticides in polished rice by LC-MS/MS

Four different extraction and clean-up protocols based on the QuEChERS method were compared for the development of an optimized sample preparation procedure for the multiresidue analysis of 16 commonly applied herbicides in rice crops using LC-QqQ/MS. Additionally the methods were evaluated for the analysis of 26 insecticides and fungicides currently used in rice crops. The methods comprise, in general, the hydratation of the sample with water followed by the extraction with acetonitrile, phase separation with the addition of different salts and finally a clean-up step with various sorbents.Matrix effects were evaluated for the 4 studied methods using LC-QqQ/MS. Additionally LC-TOF/MS was used to compare the co-extractants obtained with the four assayed methodologies. Thirty-six pesticides presented good performance with recoveries in the range 70-120% and relative standard deviations below 20% using 7.5 g of milled polished rice and the buffered acetate QuEChERS method without clean-up at both fortification levels: 10 and 300 μg kg⁻¹. The other six pesticides presented low recovery rates, nevertheless all these analytes could be analyzed with at least one of the other three studied procedures.     

Pretreatment and one-shot separating analysis of whole catecholamine metabolites in plasma by using LC/MS

Catecholamines are biogenic amines that play an important role in the nervous system. Some catecholamines have been used as tumor makers of phenochromocytoma, paraganglioma and neuroblastoma. The analysis of total catecholamine metabolites should be useful for one-shot screening of multiple aspects of diseases; however, it is difficult to do this, because the catecholamine metabolites are divided into three groups: five amines, one amino acid and three carbonic acids. Catecholamines and small molecules were separated from plasma proteins by an internal-surface reversed-phase column (protein-coated octadeyclsilica column) and were analyzed by liquid chromatography (LC)/mass spectrometry (MS) using electrospray ionization time-of-flight MS. Using a reversed-phase column and hydrophilic mobile phases, we succeeded in the separation of nine catecholamines, all of which had similar structures. These nine substances were eluted in the following order: norepinephrine, epinephrine, normetanephrine, dopamine, metanephrine, 3,4-dihydroxyphenylalanine, vanillomandelic acid, 3,4-dihydroxyphenylacetic acid and homovanillic acid. The reproducibility of this method was acceptable. The highest coefficient of variation was 7.4%. In addition, various types of compounds were separated from and detected in plasma proteins by applying LC/MS. The plasma direct injection method, which uses an internal-surface reversed-phase column and an ion-pair reagent, allowed us to separate small molecules from plasma proteins. MS detected some compounds that high-performance LC could not succeed in separating and detecting with UV detection. We think that the method can be applied to find new markers in neuroblastoma, by comparing the plasma of patients with that of normal infants. The method can be also used to help in making a diagnosis of other diseases and finding their new makers.     

A simple,fast, and sensitive method for the measurement of serum nicotine,cotinine, and nornicotine by LC–MS/MS

The measurement of nicotine and its metabolites has been used to monitor tobacco use. A high‐sensitivity method (<1 ng/mL) is necessary for the measurement in serum or plasma to differentiate nonsmokers from passive smokers. Here, we report a novel LC–MS/MS method to quantify nicotine, cotinine, and nornicotine in serum with high sensitivity. Sample preparation involved only protein precipitation, followed by online turbulent flow extraction and analysis on a porous graphitic carbon column in alkaline conditions. The chromatography time was 4 min. No significant matrix effects or interference were observed. The lower limit of quantification was 0.36, 0.32, and 0.38 ng/mL for nicotine, cotinine, and nornicotine, respectively, while accuracy was 91.6–117.1%. No carryover was observed up to a concentration of 48 , 550, and 48 ng/mL for nicotine, cotinine, and nornicotine, respectively. Total CV was <6.5%. The measurement of nicotine and cotinine was compared with an independent LC–MS/MS method and concordant results were obtained. In conclusion, this new method was simple, fast, sensitive, and accurate. It was validated to measure nicotine, cotinine, and nornicotine in serum for monitoring tobacco use.     

Comparison of QuEChERS sample preparation methods for the analysis of pesticide residues in fruits and vegetables

This article describes the comparison of different versions of an easy, rapid and low-cost sample preparation approach for the determination of pesticide residues in fruits and vegetables by concurrent use of gas and liquid chromatography (GC and LC) coupled to mass spectrometry (MS) for detection. The sample preparation approach is known as QuEChERS, which stands for “quick, easy, cheap, effective, rugged and safe”. The three compared versions were based on the original unbuffered method, which was first published in 2003, and two interlaboratory validated versions: AOAC Official Method 2007.01, which uses acetate buffering, and European Committee for Standardization (CEN) Standard Method EN 15662, which calls for citrate buffering. LC–MS/MS and GC–MS analyses using each method were tested from 50 to 1000 ng/g in apple–blueberry sauce, peas and limes spiked with 32 representative pesticides. As expected, the results were excellent (overall average of 98% recoveries with 10% RSD) using all 3 versions, except the unbuffered method gave somewhat lower recoveries for the few pH-dependent pesticides. The different methods worked equally well for all matrices tested with equivalent amounts of matrix co-extractives measured, matrix effects on quantification and chemical noise from matrix in the chromatographic backgrounds. The acetate-buffered version gave higher and more consistent recoveries for pymetrozine than the other versions in all 3 matrices and for thiabendazole in limes. None of the versions consistently worked well for chlorothalonil, folpet or tolylfluanid in peas, but the acetate-buffered method gave better results for screening of those pesticides. Also, due to the recent shortage in acetonitrile (MeCN), ethyl acetate (EtOAc) was evaluated as a substitute solvent in the acetate-buffered QuEChERS version, but it generally led to less clean extracts and lower recoveries of pymetrozine, thiabendazole, acephate, methamidophos, omethoate and dimethoate. In summary, the acetate-buffered version of QuEChERS using MeCN exhibited advantages compared to the other tested methods in the study.     

Evaluation of two molecularly imprinted polymers for the solid‐phase extraction of natural,synthetic and mycoestrogens from environmental water samples before liquid chromatography with mass spectrometry

In this work, we have compared the selectivity of two commercial molecularly imprinted polymers (AFFINIMIP®SPE Estrogens and AFFINIMIP®SPE Zearalenone) for the extraction of 12 estrogenic compounds of interest (i.e. 17α‐estradiol, 17β‐estradiol, estrone, hexestrol, 17α‐ethynylestradiol, diethylstibestrol, dienestrol, zearalenone, α‐zearalanol, β‐zearalanol, α‐zearalenol and β‐zearalenol) from different water samples. High‐performance liquid chromatography coupled with ion trap mass spectrometry with electrospray ionization was used for their determination. Results showed that although both molecularly imprinted polymeric cartridges were specifically designed for different groups of analytes (natural estrogens like estradiol in the first case and zearalenone derivatives in the second) they nearly have the same extraction performance (with recovery values in the range 65–101%) for the same analytes in Milli‐Q water because of the cross‐reactivity of the polymer. However, when more complex water samples were analyzed, it was clear that the behavior was different and that the AFFINIMIP®SPE Estrogens showed less cross‐reactivity than the other cartridge. Validation of the proposed methodology with both cartridges revealed that the extraction was reproducible and that the final limits of detection of the proposed method were in the low ng/L range.     

Development of a sample preparation procedure of sewage sludge samples for the determination of polycyclic aromatic hydrocarbons based on selective pressurized liquid extraction

An automated, simple and sensitive method based on selective pressurized liquid extraction (SPLE) was developed for the analysis of polycyclic aromatic hydrocarbons in sewage sludge samples. The new sample preparation procedure consists of on-line clean-up by inclusion of sorbents in the extraction cell, and combines elevated temperatures and pressures with liquid solvents to achieve fast and efficient removal of target analytes from complex sewage sludge matrices. The effects of various operational parameters (e.g. sample pretreatment, extraction solvent, temperature, pressure, static time, etc.) on the performance of SPLE procedure were carefully investigated, obtaining the best results when SPLE conditions were fixed at 140 °C, 1500 psi, static time of 5 min and n-hexane as extraction solvent. A new programmed temperature vaporization–gas chromatography–tandem mass spectrometry method based on large volume injection (PTV–LVI–GC–MS/MS) was also developed and analytical determinations were performed by high performance liquid chromatography coupled with fluorescence detection and GC–MS/MS. The extraction yields for the different compounds obtained by SPLE ranged from 84.8% to 106.6%. Quantification limits obtained for all of these studied compounds (between 0.0001 and 0.005 μg g⁻¹, dry mass) were well below the regulatory limits for all compounds considered. To test the accuracy of the SPLE technique, the optimized methodology was applied to the analysis of a certified reference material (sewage sludge (BCR088)) and a reference material (sewage sludge (RTC-CNS312-04)), with excellent results.     

Multiresidue analysis of nine β‐agonists in animal muscles by LC‐MS/MS based on a new polymer cartridge for sample cleanup

A novel, sensitive, and reliable LC‐MS/MS method for multiresidue analysis of nine β‐agonists (salbutamol, terbutaline, cimaterol, fenoterol, clorprenaline, ractopamine, tulobuterol, clenbuterol, and penbuterol) in four farm animal muscles was developed. Muscle matrix was extracted with acetonitrile–10% sodium carbonate solution, and then was subjected to cleanup using a SPE cartridge packed with new polymer synthesized in acetone. Chromatographic separation of the components was performed on a Luna C₁₈ column using 0.1% of formic acid in water and acetonitrile. The mass spectrometer was operated in the positive electrospray mode. Good precision and accuracy were obtained for all analytes (except for fenoterol) at the spiked three levels of 1.0, 10, and 50 μg/kg. The decision limit and detection capability of nine β‐agonists ranged from 0.04 to 0.18 and 0.15 to 0.69 μg/kg, respectively. The method developed was successfully applied to the monitoring of nine β‐agonists in pork, beef, mutton, and chicken from Chinese markets.     

New extraction procedure to improve the determination of quinolones in poultry muscle by liquid chromatography with ultraviolet and mass spectrometric detection

The present article aims to develop a new extraction procedure to improve the determination of quinolones in chicken muscle. This new determination method was validated using liquid chromatography–ultraviolet detection (LC–UV) and liquid chromatography–mass spectrometry detection (LC–MS), which has special bearing on stability studies. The results obtained by using the method were compared with the results obtained with a previous methodology. The new extraction procedure presents a sensitivity low enough to determine concentration of these drugs below the permissible maximum residue limits (MRL) in chicken muscle and is less time consuming than the previous methodology.     

Development of a CE‐MS method for the study of riociguat and metabolite M1 in pharmaceutical analysis

Riociguat is a novel antihypertensive drug for the treatment of pulmonary hypertension. We present electrophoretic characterization, i.e. migration behavior of riociguat and metabolite M1 as support for optimized CZE/MS assay. Fundamental separation parameters, such as peak width, symmetry, and resolution are studied in a series of ammonium formate buffers within pH range 2.60–5.61. The narrow region of peak symmetry lies close to pH 4.0 for both analytes. Accordingly, the value of resolution maximizes in a background electrolyte adjusted to pH 4.10. Basic calibration parameters estimated from CZE experiments with absorption photometric and mass spectrometric detection of riociguat and metabolite M1 were evaluated. More than three orders lower LOD was achieved with high resolution mass spectrometric detection. The observed difference in the sensitivity of both detection techniques gives priority to the utilization of CZE/MS in practice. The values of dissociation constants of riociguat and metabolite M1, pK_BH, were determined from CZE measurements in lithium formate and lithium acetate background electrolytes with constant ionic strength. The value of pK_BH = 4.30 ± 0.02 for riociguat corresponds well to the value already presented in the literature. According to our observation, metabolite M1 behaves like a slightly stronger base with estimated pK_BH = 4.40 ± 0.02.