微观相场法模拟Ni75Al5.3V19.7 中L12和D022结构反位缺陷的演化

运用微观相场法研究Ni₇₅Al_5.3V_19.7合金沉淀过程中L1₂结构和D0₂₂结构反位缺陷发现：在沉淀初期,L1₂结构反位缺陷Al_Ni,V_Ni,Ni_Al,D0₂₂结构反位缺陷V_Ni,Al_Ni关键词： 微观相场 反位缺陷 L1₂结构')" href="#">L1₂结构 D0₂₂结构')" href="#">D0₂₂结构     

Hydrogen permeation characteristics of rolled V85Al10Co5 alloys

Thin sheets of V₈₅Al₁₀Co₅ alloy were produced by a thermo-mechanical treatment consisting in successive hot rolling, cold rolling steps and annealing treatment at high temperature followed by either air cooling or water quenching. Though the values of hydrogen permeability measured for these sheets were significantly reduced as a consequence of the rolling process, the annealing treatment restored almost the hydrogen permeation properties to those of the alloy in the cast condition. EBSD analyses suggested that the post-annealing treatment performed at 1100 °C for 3 min after cold rolling induced a recrystallization of the grains resulting in a preferred orientation along the {002} planes. For the sample annealed and water quenched, the value of the hydrogen flux reached about 45 ml/cm².min, which is more than twice the value of the flux obtained for thin foils of Pd alloys tested under identical conditions.     

Interfacial reactions and oxidation behavior of Al2O3 and Al2O3/Al coatings on an orthorhombic Ti2AlNb alloy

The uniform and dense Al₂O₃ and Al₂O₃/Al coatings were deposited on an orthorhombic Ti₂AlNb alloy by filtered arc ion plating. The interfacial reactions of the Al₂O₃/Ti₂AlNb and Al₂O₃/Al/Ti₂AlNb specimens after vacuum annealing at 750 °C were studied. In the Al₂O₃/Ti₂AlNb specimens, the Al₂O₃ coating decomposed significantly due to reaction between the Al₂O₃ coating and the O-Ti₂AlNb substrate. In the Al₂O₃/Al/Ti₂AlNb specimens, a γ-TiAl layer and an Nb-rich zone came into being by interdiffusion between the Al layer and the O-Ti₂AlNb substrate. The γ-TiAl layer is chemically compatible with Al₂O₃, with no decomposition of Al₂O₃ being detected. No internal oxidation or oxygen and nitrogen dissolution zone was observed in the O-Ti₂AlNb alloy. The Al₂O₃/Al/Ti₂AlNb specimens exhibited excellent oxidation resistance at 750 °C.     

Anodization of aluminium thin films on pSi and annihilation of strong luminescence from Al2O3

Photoluminescence (PL) of Al₂O₃ films obtained by anodization of thermally evaporated and annealed thin Al films on p⁺⁺Si in 0.3 M oxalic acid has been investigated. Thermal annealing at 200–950 °C under the dry nitrogen atmosphere was used for deactivation of luminescence centres. Luminescence from as grown films was broad and located at 425 nm. This luminescence reached to highest level after annealing at 600 °C. Maximum 10 min was required for full optical activation and prolonged annealing up to 4 h did not change the luminescence intensity. Because of deep levels, absorption band edge of as grown films was shifted to the lower energy which is 3.25 eV. Annealing above 800 °C reduced the PL intensity and this observation was correlated with the blue shift of band edge as the defects annealed out. Disappearing PL intensity and blue shift of band edge absorption after annealing at 950 °C was mainly attributed to the oxygen-related defects and partly to impurities that may be originated from oxalic acid. AFM results did not show any hexagonally ordered holes but uniformly distributed nanosized Al₂O₃ clusters that were clearly seen. XRD measurements on as grown Al₂O₃ showed only [1 1 0] direction of α phase. Debye–Scherer calculation for this line indicates that cluster size is 35.7 nm. XRD and AFM pictures suggest that nanocrystalline Al₂O₃ are embedded in amorphous Al₂O₃.     

Preparation and properties of composite ceramic coating containing Al2O3–ZrO2–Y2O3 on AZ91D magnesium alloy by plasma electrolytic oxidation

A composite ceramic coating containing Al₂O₃–ZrO₂–Y₂O₃ was successfully prepared on AZ91D magnesium alloy by plasma electrolytic oxidation (PEO) technique in an alkaline aluminate electrolyte. The morphology, elemental and phase composition, corrosion behavior and thermal stability of the uncoated and coated samples were studied by environmental scanning electron microscopy (ESEM), energy dispersive X-ray spectrometer (EDS), X-ray diffractometer (XRD), electrochemical corrosion test, high temperature oxidation test and thermal shock test. The results showed that the composite ceramic coating was composed of Al₂O₃, c-ZrO₂, t-ZrO₂, Y₂O₃ and some magnesium compounds, such as MgO, MgF₂ and MgAl₂O₄. After PEO treatment, the corrosion potential of AZ91D alloy was increased and the corrosion current density was significantly reduced. Besides, the coated magnesium alloys also showed excellent high temperature oxidation resistance and thermal shock resistance at 500 °C environment.     

Solvothermal synthesis of high hydrogen permeable Pd/Ag alloy particles and their hydrogen transport properties

Pd₇₆Ag₂₄ nanoparticles with high purity and a face-centered cubic structure were prepared using a solvothermal method. The lattice parameter of the Pd₇₇Ag₂₃ nanopowders (space group 225Fm3m) was calculated to be a?=?3.9382 Å. The primary particle size was calculated to be 7.7 nm from the X-ray line width using the Scherrer formula, and the interplanar distances was estimated to be 2.272 and 2.000 Å based on indexing on the (111) and (200) plane, respectively. These values are slightly larger than those of pure Pd and smaller than Ag in the (111) plane. The linear relationship of the hydrogen permeation flux with the square root of the hydrogen partial pressure gradient across a 0.26-mm-thick Pd/Ag-YSZ cermet membrane confirmed the major hydrogen transport through the Pd/Ag phase of cermet membranes. The Pd/Ag-YSZ cermet membranes showed significantly higher hydrogen permeation flux than the Pd-YSZ cermet membrane, even though the activation energy for the Pd/Ag alloy cermet membranes showed slightly higher values than that of the Pd cermet membranes. The hydrogen–oxygen dual flux through Pd/Ag-YSZ cermet membranes was confirmed by the maximum hydrogen production by combining the ability of hydrogen production from water with the function of hydrogen separation on composite membranes     

Correlation between Al2O3 particles and interface of Al-Al2O3 coatings by cold spray

Al-Al₂O₃ composite coatings with different Al₂O₃ particle shapes were prepared on Si and Al substrate by cold spray. The powder compositions of metal (Al) and ceramic (Al₂O₃) having different sizes and agglomerations were varied into ratios of 10:1 wt% and 1:1 wt%. Al₂O₃ particles were successfully incorporated into the soft metal matrix of Al. It was found that crater formation between the coatings and substrate, which is typical characteristic signature of cold spray could be affected by initial starting Al₂O₃ particles. In addition, when the large hard particles of fused Al₂O₃ were employed, the deep and big craters were generated at the interface between coatings and hard substrates. In the case of pure soft metal coating such as Al on hard substrate, it is very hard to get proper adhesion due to lack of crater formation. Therefore, the composite coating would have certain advantages.     

Optical properties of Ag–Al2O3 nano-array composite structure

Ag/Al₂O₃ nano-array composite structures were obtained by alternating current (AC) electrodeposition of Ag into the pores of anodic alumina membrane (AAM). The ordered wire-grid structure of Ag nanowires formed along a preferential direction, typically 20 nm in diameter, was fabricated. XRD revealed that Ag₂O is also preserved in the pores of AAM. Optical properties of Ag/Al₂O₃ prepared at different annealing temperatures were measured by using spectrometer. Transmission spectra indicate that the transmittance of Ag/Al₂O₃ increases obviously with the increasing of annealing temperature. Polarization spectra indicate that Ag/Al₂O₃ has good polarization in the range of 900–2000 nm, and the extinction ratio increases with the increasing of the annealing temperature or incident angle.     

Effect of TiO2/Al2O3 film coated diamond abrasive particles by sol-gel technique

The diamond abrasive particles were coated with the TiO₂/Al₂O₃ film by the sol-gel technique. Compared with the uncoated diamonds, the TiO₂/Al₂O₃ film was excellent material for the protection of the diamonds. The results showed that the incipient oxidation temperature of the TiO₂/Al₂O₃ film coated diamonds in air atmosphere was 775 °C, which was higher 175 °C than that of the uncoated diamonds. And the coated diamonds also had better the diamond's single particle compressive strength and the impact toughness than that of uncoated diamonds after sintering at 750 °C. For the vitrified bond grinding wheels, replacing the uncoated diamonds with the TiO₂/Al₂O₃ film coated diamonds, the volume expansion of the grinding wheels decreased from 6.2% to 3.4%, the porosity decreased from 35.7% to 25.7%, the hardness increased from 61.2H_RC to 66.5H_RC and the grinding ratio of the vitrified bond grinding wheels to carbide alloy (YG8) increased from 11.5 to 19.1.     

Synthesis,crystal structure and magnetic properties of Yb8Ag18.5Al47.5, Yb2Pd2Cd and Yb1.35Pd2Cd0.65

We report the synthesis of three new Yb-based compounds, Yb₈Ag_18.5Al_47.5 (Yb₈Cu₁₇Al₄₉-type, tetragonal tI74–I4/mmm), Yb₂Pd₂Cd (Mo₂B₂Fe-type, tetragonal tP10-P4/mbm) and Yb_1.35Pd₂Cd_0.65 (MnCu₂Al-type, cubic cF16–Fm3¯m). The crystal symmetry of these compounds has been determined and the complete structural characterisation carried out by single crystal and powder diffraction techniques. Two symmetry in-equivalent sites are available for the Yb ions in Yb₈Ag_18.5Al_47.5 and Yb_1.35Pd₂Cd_0.65. The 4f levels of the Yb ions are appreciably hybridised in Yb₈Ag_18.5Al_47.5 and to a lesser extent in Yb₂Pd₂Cd as inferred from the magnetisation and heat capacity data. Signatures of heavy fermion behaviour are observed in the heat capacity data of Yb₂Pd₂Cd in which the heat capacity, C/T, increases at low temperatures attaining a value of ≈600 mJ/mol K² at 1.8 K. The electrical resistivity of Yb₂Pd₂Cd follows a linear variation with temperature, T, between 1.4 and 5 K, thus indicating a possible non-Fermi liquid behaviour. In contrast, Yb ions are trivalent in Yb_1.35Pd₂Cd_0.65 and order magnetically near 1.4 K.     

Electrical properties vs. microstructure of nanocrystallized V2O5-P2O5 glasses — An extended temperature range study

An electronically conducting nanomaterial was synthesized by nanocrystallization of a 90V₂O₅·10P₂O₅ glass and its electrical properties were studied in an extended temperature range from − 170 to + 400 °C. The conductivity of the prepared nanomaterial reaches 2 ? 10^− 1 S cm^− 1 at 400 °C and 2 ? 10^− 3 S cm^− 1 at room temperature. It is higher than that of the original glass by a factor of 25 at room temperature and more than 100 below − 80 °C. A key role in the conductivity enhancement was ascribed to the material's microstructure, and in particular to the presence of the large number of small (ca. 20 nm) grains of crystalline V₂O₅. The observed conductivity dependencies are discussed in terms of the Mott's theory of the electronic hopping transport in disordered systems. Since V₂O₅ is known for its ability to intercalate lithium, the presented results might be helpful in the development of cathode materials for Li-ion batteries.     

Effect of annealing temperature on microstructure, optical and electrical properties of sputtered Ba0.9Sr0.1TiO3 thin films

Ba_0.9Sr_0.1TiO₃ (BST) thin films were deposited on fused quartz and Pt/TiN/Si₃N₄/Si substrates by radio frequency magnetron sputtering technique. Microstructure and chemical bonding states of the BST films annealed at 700 °C were characterized by field emission scanning electron microscopy, X-ray photoelectron spectroscopy, glancing angle X-ray diffraction and Raman spectrum. Optical constants including refractive indices, extinction coefficients and bandgap energies of the as-deposited BST film and the BST films annealed at 650, 700 and 750 °C, respectively, were determined from transmittance spectra by envelope method and Tauc relation. Dielectric constant and remnant polarization for the BST films increase with increasing annealing temperature. Leakage current density-applied voltage (J–V) data indicate that the dominant conduction mechanism for all the BST capacitors is the interface-controlled Schottky emission under the conditions of 14 V < V < 30 V and −30 V < V < −14 V. Furthermore, the inequipotential J–V characteristics for the BST films annealed at various temperatures are mainly attributed to the combined effects of the different thermal histories, relaxed stresses and strains, and varied Schottky barrier heights in the BST/Pt and Pt/BST interfaces.     

Al2O3:V3+晶体局域结构及其自旋哈密顿参量研究

提出了解释掺杂离子局域结构畸变的配体平面移动模型，建立了此模型下晶体微观结构与自旋哈密顿参量之间的定量关系.在考虑自旋与自旋、自旋与另一电子轨道和轨道与轨道作用等微小磁相互作用的基础上，采用全组态完全对角化方法，对Al₂O₃晶体中V³⁺的局域结构和自旋哈密顿参量进行了系统的研究.结果表明，V³⁺掺入Al₂O₃晶体后，上下配体氧平面间距离增大了0.0060 nm.从而成功地解释了Al₂O₃:V³⁺晶体的自旋哈密顿参量.在此基础上，研究了三角晶场下3d²离子自旋哈密顿参量的微观起源.研究发现，自旋三重态对自旋哈密顿参量的贡献是主要的，微小磁相互作用对自旋哈密顿参量的贡献只与自旋三重态有关.     

Synthesis of VO2 (B) nanorods for Li battery application

Vanadium dioxide nanorods were synthesized through a hydrothermal reaction from V₂O₅ xerogel, poly(vinyl pyrrolidone) (PVP) and lithium perchlorate (LiClO₄). The prepared samples were characterized by X-ray diffraction, infrared spectroscopy, scanning electron microscopy (SEM), transmission electron microscopy (TEM) and electrochemical discharge–charge cycling in lithium battery. SEM images reveal the nanorods to have dimensions on the order of 1–3 μm in length and 10–50 nm in diameter. The measured initial discharge capacity of the lithium battery with a cathode made of VO₂ (B) nanorods was 152 mA h/g.     

The low temperature synthesis of Euand Dy activated Sr3Al2O6 nanophosphors by microwave method

The Eu²⁺and Dy³⁺ activated Sr₃Al₂O₆ (S3A2O-ED) nanophosphors were synthesized by a new microwave method. The S3A2O-ED sample calcined in microwave oven at around 650 °C for 20 min possesses a cubic Sr₃Al₂O₆ single phase. The sample showed small size (80–100 nm) and spherical shape. The excitation and emission spectra indicated that excitation broad band chiefly sited in visible range and the nanophosphors emitted strong light at 611 nm under around 473 nm excitation. Comparing with conventional method, the microwave synthesis of S3A2O-ED greatly decreased the calcining temperature and time. However, the brightness of S3A2O-ED nanophosphors was reduced. The change of luminescent intensity in S3A2O-ED nanophosphors could be attributed to the effect of surface energy.     

The electrical properties of dielectric stacks of SiO2 and Al2O3 prepared by atomic layer deposition method

We produced dielectric stacks composed of ALD SiO₂ and ALD Al₂O₃, such as SiO₂/Al₂O₃, Al₂O₃/SiO₂, and SiO₂/Al₂O₃/SiO₂, and measured the leakage currents through the stacks in comparison with those of the single oxide layers. SiO₂/Al₂O₃ shows lowest leakage current for negative bias region below 6.4 V, and Al₂O₃/SiO₂ showed highest current under negative biases below 4.5 V. Two distinct electron conduction regimes are observed for Al₂O₃ and SiO₂/Al₂O₃. Poole-Frenkel emission is dominant at the high-voltage regime for both dielectrics, whereas the direct tunneling through the dielectric is dominant at the low-voltage regime. The calculated transition voltage between two regimes for SiO₂ (6.5 nm)/Al₂O₃ (12.6 nm) is −6.4 V, which agrees well with the experimental observation (−6.1 V). For the same EOT of entire dielectric stack, the transition voltage between two regimes decreases with thinner SiO₂ layer.     

Structure, ferroelectric and piezoelectric properties of (Bi1−x−yNa0.925−x−yLi0.075)0.5BaxSryTiO3 lead-free piezoelectric ceramics

Lead-free multi-component ceramics (Bi_1−x−yNa_{0.925−x−y}Li_0.075)_0.5Ba_xSr_yTiO₃ have been prepared by an ordinary sintering technique and their structure and electrical properties have been studied. All the ceramics can be well-sintered at 1100 °C. X-ray diffraction patterns shows that Li⁺, Ba²⁺ and Sr²⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a new solid solution with a pure perovskite structure, and a morphotropic phase boundary (MPB) is formed at 0.04 < x < 0.08. As compared to pure Bi_0.5Na_0.5TiO₃ ceramic, the coercive field E_C of the ceramics decreases greatly and the remanent polarization P_r of the ceramics increases significantly after the formation of the multi-component solid solution. Due to the MPB, lower E_C and higher P_r, the piezoelectricity of the ceramics is greatly improved. For the ceramics with the compositions near the MPB (x = 0.04–0.08 and y = 0.02–0.04), piezoelectric coefficient d₃₃ = 133–193 pC/N and planar electromechanical coupling factor k_P = 16.2–32.1%. The depolarization temperature T_d reaches a minimum value near the MPB. The temperature dependences of the ferroelectric and dielectric properties suggest that the ceramics may contain both the polar and non-polar regions at temperatures near/above T_d.     

Microstructure and properties of Ni-Co/nano-Al2O3 composite coatings by pulse reversal current electrodeposition

Ni-Co/nano-Al₂O₃ (Ni-Co/Al₂O₃) composite coatings were prepared under pulse reversal current (PRC) and direct current (dc) methods respectively. The microstructure of coatings was characterized by means of XRD, SEM and TEM. Both the Ni-Co alloy and composite coatings exhibit single phase of Ni matrix with face-centered cubic (fcc) crystal structure, and the crystal orientation of the Ni-Co/Al₂O₃ composite coating was transformed from crystal face (2 0 0) to (1 1 1) compared with alloy coatings. The hardness, anti-wear property and macro-residual stress were also investigated. The results showed that the microstructure and performance of the coatings were greatly affected by Al₂O₃ content and the electrodeposition methods. With the increasing of Al₂O₃ content, the hardness and wear resistance of the composite coatings enhanced. The PRC composite coatings exhibited compact surface, high hardness, better wear resistance and lower macro-residual stress compared with that of the dc composite coatings.     

Substrate effects on V2O3 thin films

We apply density functional theory and the augmented spherical wave method to analyze the electronic structure of V₂O₃ in the vicinity of an interface to Al₂O₃. The interface is modeled by a heterostructure setup of alternating vanadate and aluminate slabs. We focus on the possible modifications of the V₂O₃ electronic states in this geometry, induced by the presence of the aluminate layers. In particular, we find that the tendency of the V 3d states to localize is enhanced and may even cause a metal-insulator transition.     

Transport properties and defect analysis of La1.9Sr0.1NiO4 + δ

The oxygen flux through La_1.9Sr_0.1NiO_4 + δ has been measured as a function of oxygen activity gradient and temperature (750–1000 °C). The oxygen nonstoichiometry was determined by thermogravimetry in the temperature range of 400–1000 °C and oxygen partial pressures of 0.0002–1 atm. The total conductivity was measured over a similar range of conditions. The oxide ion partial conductivity derived from the oxygen flux data is approximately 4 orders of magnitude lower than the total, mainly p-type electronic conductivity. The defect structure was derived based on the data. Combining the oxygen flux and oxygen nonstoichiometry, the self diffusion coefficient of oxygen interstitials was evaluated.