Buffer-less Cu(In,Ga)Se2 solar cells by band offset control using novel transparent electrode

Cu(In,Ga)Se₂ (CIGS) solar cells without buffer layers have been demonstrated. Currently, CdS, Zn(O,S,OH), ZnS, or InS buffer layers are used in high efficiency CIGS solar cells to suppress interface recombination. One of the important parameters to reduce the recombination is the conduction band offset (CBO) between the buffer and CIGS layers. In this study, we have proposed the use of a novel transparent conductive oxide (TCO) which can control the CBO to reduce interface recombination and eliminate the buffer layers. The device simulation was used to verify the effect of CBO control theoretically. Then, the novel TCO material of ZnO_1?xS_x:Al prepared by co-sputtering of ZnO:Al₂O₃ and ZnS targets was fabricated to verify the CBO effect experimentally. The efficiency of a CIGS solar cell with a ZnO:Al/CIGS/Mo/soda-lime glass structure, i.e. buffer-less structure using a conventional TCO, was significantly low because of severe shunting. In contrast, the use of ZnO_1-xS_x:Al instead of ZnO:Al increased the shunt resistance of the CIGS solar cell, resulting in higher open-circuit voltage and efficiency. The result is the first proof of the concept of the buffer-less CIGS solar cells.     

Structural and optical properties of ZnO nanorods grown on MgxZn1−xO buffer layers

ZnO nanorod arrays were synthesized by chemical-liquid deposition techniques on Mg_xZn_1−xO (x = 0, 0.07 and 0.15) buffer layers. It is found that varying the Mg concentration could control the diameter, vertical alignment, crystallization, and density of the ZnO nanorods. The X-ray diffraction (XRD), transmission electron microscopy (TEM), and selected area electron diffraction (SAED) data show the ZnO nanorods prefer to grow in the (0 0 2) c-axis direction better with a larger Mg concentration. The photoluminescence (PL) spectra of ZnO nanorods exhibit that the ultraviolet (UV) emission becomes stronger and the defect emission becomes weaker by increasing the Mg concentration in Mg_xZn_1−xO buffer layers.     

Thickness study of Al:ZnO film for application as a window layer in Cu(In1−xGax)Se2 thin film solar cell

Structural, electrical and optical properties of Al doped ZnO (Al:ZnO) thin film of various thicknesses, grown by radio-frequency magnetron sputtering system were studied in relation to the application as a window layer in Cu(In_1−xGa_x)Se₂ (CIGS) thin film solar cell. It was found that the electrical and structural properties of Al:ZnO film improved with increasing its thickness, however, the optical properties degraded. The short circuit current density, J_sc of the fabricated CIGS based solar cells was significantly influenced by the variation of the Al:ZnO window layer thickness. Best efficiency was obtained when CIGS solar cell was fabricated with electrically and optically optimized Al:ZnO window layer.     

Influence of Mg content on optical properties of exciton confinement in wurtzite ZnO/MgxZn1−xO coupled quantum dots

Based on the framework of effective-mass approximation and variational approach, optical properties of exciton are investigated theoretically in ZnO/Mg_xZn_1−xO vertically coupled quantum dots (QDs), with considering the three-dimensional confinement of electron and hole pair and the strong built-in electric field effects. The exciton binding energy, the emission wavelength and the oscillator strength as functions of the structural parameters (the dot height, the barrier thickness between the coupled wurtzite ZnO QDs and Mg content x in the barrier layers) is calculated in detail. The results elucidate that Mg content have a significant influence on the exciton state and optical properties of ZnO coupled QDs. When Mg content x increases, the strong built-in electric field increases and leads to the redshift of the effective band gap of the Mg_xZn_1−xO layer. These theoretical results are useful for design and application of some important photoelectronic devices constructed by using ZnO strained QDs.     

Zn1−xMgxO/ZnO heterostructures studied by Kelvin probe force microscopy conjunction with probe characterizer

The surface potential of Zn_1−xMg_xO/ZnO heterostructure grown by radical source molecular beam epitaxy was measured by Kelvin force microscopy (KFM). A clear correlation was observed between the topographic image and the surface potential of Zn_0.56Mg_0.44O/ZnO heterostructure. The potential area around the surface pits was about 60 mV lower than that of the surrounding region, which suggests the effects of the pits on the electrical properties of the potential layer. In order to guarantee the accuracy of measurement, the probe shape was analyzed by probe characterizer and using Au thin films as a potential standard.     

Growth of cubic MgxZn1−xO alloy films by electron beam evaporation

We report the growth of cubic Mg_xZn_1−xO alloy thin films on quartz by electron beam evaporation. It can be found that all the samples have sharp absorption edges by the absorption measurements. X-ray diffraction measurements indicate the Mg_xZn_1−xO films are cubic phase with preferred orientation along the (1 1 1) direction. Energy dispersive spectrometry (EDS) demonstrates that the Mg concentration in Mg_xZn_1−xO films is much higher than the ceramic target used, and the composition can be tuned in a small scope by varying the substrate temperature and the beam electric current. The reasons of this phenomenon are also discussed.     

Properties of MgxZn1−xO thin films sputtered in different gases

Mg_xZn_1−xO alloy films were prepared on sapphire substrates using Ar and N₂ as the sputtering gases. The effect of the sputtering gas on the structural, optical and electrical properties of the Mg_xZn_1−xO films was studied. By using N₂ as the sputtering gas, the Mg_xZn_1−xO film shows p-type conductivity and the band gap is larger than that employing Ar as the sputtering gas. The reason for this phenomenon is thought to be related to the reaction between N-O or N-Zn, and the N-doping.     

BiFeO3/Zn1−xMnxO bilayered thin films

BiFeO₃/Zn_1−xMn_xO (x = 0-0.08) bilayered thin films were deposited on the SrRuO₃/Pt/TiO₂/SiO₂/Si(1 0 0) substrates by radio frequency sputtering. A highly (1 1 0) orientation was induced for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO thin films demonstrate diode-like and resistive hysteresis behavior. A remanent polarization in the range of 2P_r ∼ 121.0-130.6 μC/cm² was measured for BiFeO₃/Zn_1−xMn_xO. BiFeO₃/Zn_1−xMn_xO (x = 0.04) bilayer exhibits a highest M_s value of ∼15.2 emu/cm³, owing to the presence of the magnetic Zn_0.96Mn_0.04O layer with an enhanced M_s value.     

Electric-field-induced energy spectra and dispersions of ZnO/MgxZn1−xO MQWs

The energy spectra and dispersion relations of carriers in the presence of an electric field applied along the growth direction in ZnO/Mg_xZn_1−xO multiple quantum wells (MQW) are calculated using the asymptotic transfer method (ATM) on the basis of the quasistationary state approximation. The energy spectra of the carriers induce some quasi-bound levels under electric fields. The dispersion relations for the energy of the ground state and lower excitation states still have parabolic shapes for both the electrons and the heavy holes in the presence of a moderate electric field. Our results also reveal that the number of energy levels increases with increasing number of ZnO quantum wells and that the energies increase with both increasing Mg composition x and electric field strength.     

Oxygen flux influence on the morphological, structural and optical properties of Zn1−xMgxO thin films grown by plasma-assisted molecular beam epitaxy

The Zn_1−xMg_xO thin films were grown on Al₂O₃ substrate with various O₂ flow rates by plasma-assisted molecular beam epitaxy (P-MBE). The growth conditions were optimized by the characterizations of morphology, structural and optical properties. The Mg content of the Zn_1−xMg_xO thin film increases monotonously with decreasing the oxygen flux. X-ray diffractometer (XRD) measurements show that all the thin films are preferred (0 0 2) orientated. By transmittance and absorption measurements, it was found that the band gap of the film decreases gradually with increasing oxygen flow rate. The surface morphology dependent on the oxygen flow rate was also studied by field emission scanning electron microscopy (FE-SEM). The surface roughness became significant with increasing oxygen flow rate, and the nanostructures were formed at the larger flow rate. The relationship between the morphology and the oxygen flow rate of Zn_1−xMg_xO films was discussed.     

Optical properties of MgxZn1−xO thin films deposited on silicon and sapphire substrate by rf magnetron sputtering

The index dispersion at UV–VIS range for polycrystalline Mg_xZn_1−xO films on silicon with different Mg concentration was obtained by spectroscopic ellipsometry (SE) method. It decreases with the increase of the Mg content. Above the relative peak wavelength, they are well fitted by the first-order Sellmeier relation. The band gap of films on sapphire of different Mg content was determined from transmission measurements. Photoluminescence (PL) illustrated that for Mg_xZn_1−xO films every PL peak corresponded to a special excitation wavelength. The wavelength of the PL peak was proportional to the special excitation wavelength. A strong peak was obtained in the blue band for the films due to the large amount of oxygen vacancies caused by excess Zn and Mg atoms, while weak peak at ultraviolet band.     

Microstructure and thermoelectric properties of Zn1−xAlxO ceramics fabricated by spark plasma sintering

Al-doped ZnO powders were synthesized via solid reaction between Zn(OH)₂ and Al(OH)₃ and consolidated by spark plasma sintering (SPS) to fabricate fine-grained Zn_1−xAl_xO ceramics as a thermoelectric material. X-ray diffraction and spectrophotometer experiments revealed that Al doping into ZnO is enhanced by the present process, and consequently the SPS-processed Zn_1−xAl_xO samples show significantly improved electrical conductivity as compared with those prepared via mixing ZnO and Al₂O₃ oxide powders. Because of the combined effect of Al doping and grain refinement, the present Zn_1−xAl_xO ceramics show much lower thermal conductivity, which also results in an enhanced dimensionless figure of merit (ZT), than un-doped ZnO oxides prepared also by SPS.     

The effect of growth ambient on the structural and optical properties of MgxZn1−xO thin films

Mg_xZn_1−xO (x = 0.0-0.20) thin films have been deposited by sol-gel technique on glass substrates and the effect of growth ambient (air and oxygen) on the structural, and optical properties have been investigated. The films synthesized in both ambient have hexagonal wurtzite structure. The c-axis lattice constant decreases linearly with the Mg content (x) up to x = 0.05, and 0.10 respectively for air- and oxygen-treated films, above which up to x = 0.20, the values vary irregularly with x. The change in the optical band gap values and the ultraviolet (UV) peak positions of Mg_xZn_1−xO films show the similar change with x. These results suggest that the formation of solid solution and thus the structural and optical properties of Mg_xZn_1−xO thin films are affected by the growth ambient.     

Formation of ZnO and Zn1−xCdxO films on CdTe/CdZnTe single crystals

In this work we report on the properties of ZnO and Zn_1−xCd_xO films formed on top of CdTe and CdZnTe single crystals. The films have been obtained by thermal evaporation of Zn metal films and further oxidation in atmospheric conditions. The structural and compositional characteristics of the films have been analysed by means of scanning electron microscopy and energy-dispersive X-ray analysis. The chemical composition of the films as a function of growth parameters has been obtained. It has been possible to demonstrate by Raman spectroscopy the formation of both ZnO and Zn_1−xCd_xO films. The possible inter-diffusion effects between the films and the substrate, derived from the oxidation process, have been discussed. It has been possible to check by means of photoluminescence, the optical quality of the ZnO and Zn_1−xCd_xO films, also regarding to the presence of local changes. Differences between the optical spectra obtained from various ZnO films grown on top of CdTe and CdZnTe substrates enabled the determination of compositional differences introduced by the substrate when the deposition parameters are modified.     

Effect of substrate annealing on the quality of pulsed laser deposited Zn1−xMgxO thin films

The annealing effects of sapphire substrate before deposition on the quality of epitaxial Zn_1−xMg_xO thin films grown by pulsed laser deposition are reported. Our Experimental results indicate that the surface quality of Zn_1−xMg_xO thin films and hexagonal columnar growth is improved on the annealed sapphire substrate at high temperatures due to formation of atomic terraces on the substrate surface. The photoluminescence signals also increases with the increasing annealing temperature of the substrate.     

Properties of optical phonons in Zn1−x−yMgyBexSe quaternary mixed crystal

Long wavelength optical lattice vibration and dielectric constants of the quaternary mixed crystal Zn_1−x−yMg_yBe_xSe are investigated based on the pseudo-unit-cell mode and Born-Huang procedure. It is found that this material shows a three-mode behavior and the oscillator strength of each mode is mainly controlled by only one component. The theoretical results also show that the linear interpretation method for dielectric constants is reliable. The vibrational frequencies and the oscillator strengths of the ternary mixed crystals Be_xZn_1−xSe, Be_xMg_1−xSe and Mg_xZn_1−xSe are also calculated as special cases of the quaternary mixed crystal for comparing with experiments. The calculation shows agreement with the experimental results.     

Optical properties of bulk Zn1−xCoxO magnetic semiconductors

Polycrystalline Zn_1−xCo_xO (x=0, 0.02, 0.05, 0.10 and 0.15) oxides have been synthesized by solid state reaction via sintering ZnO and Co powders in open air. X-ray diffraction analyses using Rietveld refinement indicate that a stoichiometric single phase with a wurtzite-like structure was found in Zn_1−xCo_xO samples with x up to 0.10. The elemental mapping using energy dispersive X-ray spectroscopic analyses presents a uniform distribution of Co. Optical transmittance measurements show that several extra absorption bands appear in the Co-doped ZnO, which is due to the transitions between the crystal-field-split 3d levels of tetrahedral Co²⁺ substituting Zn²⁺ ions. Raman measurements show that limited host lattice defects are induced by Co doping. Magnetization measurements reveal that the Co-doped ZnO samples are paramagnetic due to the absence of free carriers and in low temperature the dominant magnetic interaction is nearest-neighbor antiferromagnetic.     

Structural, optical and electrical properties of Zn1−xCdxO thin films prepared by PLD

Ternary polycrystalline Zn_1−xCd_xO semiconductor films with cadmium content x ranging from 0 to 0.23 were obtained on quartz substrate by pulse laser deposited (PLD) technique. X-ray diffraction measurement revealed that all the films were single phase of wurtzite structure grown on c-axis orientation with its c-axis lattice constant increasing as the Cd content x increasing. Atomic force microscopy observation revealed that the grain size of Zn_1−xCd_xO films decreases continuously as the Cd content x increases. Both photoluminescence and optical measurements showed that the band gap decreases from 3.27 to 2.78 eV with increasing the Cd content x. The increase in Cd content x also leads to the broadening of the emission peak. The resistivity of Zn_1−xCd_xO films decreases evidently for higher values of Cd content x. The shift of PL emission to visible light as well as the decrease of resistivity makes the Zn_1−xCd_xO films potential candidate for optoelectronic device.     

Optical properties of exciton confinement in wurtzite ZnO/MgxZn1−xO coupled quantum dots

Based on the framework of effective-mass approximation and variational approach, optical properties of exciton are investigated theoretically in ZnO/Mg_xZn_1−xO vertically coupled quantum dots (QDs), with considering the three-dimensional confinement of electron and hole pair and the strong built-in electric field effects due to the piezoelectricity and spontaneous polarization. The exciton binding energy, the emission wavelength and the oscillator strength as functions of the different structural parameters (the dot height and the barrier thickness between the coupled wurtzite ZnO QDs) are calculated with the built-in electric field in detail. The results elucidate that structural parameters have a significant influence on the exciton state and optical properties of ZnO coupled QDs. These results show the optical and electronic properties of the quantum dot that can be controlled and also tuned through the nanoparticle size variation.     

Optical properties of MgxZn1−xO nanowire photonic crystals

We investigate the optical properties of two-dimensional periodic arrays of well-aligned Mg_xZn_1−xO nanowires, i.e., Mg_xZn_1−xO nanowire photonic crystals. The nanowire photonic crystal can exhibit a photonic band gap in the visible range. As the mole fraction of Mg, x, increases, the edge frequencies of the band gap increase and the band gap size decreases. The characteristics of relative band gap and vacant point defect mode are also studied with varying x. From the finite-difference time-domain simulations, we show that the light extraction from nanowires can be controlled by varying the distance between optically excited nanowires and a waveguide, and the mole fraction of Mg. Controlling the light extraction from nanostructures can be useful in the implementation of nanoscale light emitting devices.