Trapping efficiencies of various collection solvents after supercritical fluid extraction

A polarity test mix consisting of acetophenone, N, N-dimethylaniline, naphthalene, decanoic acid, 2-naphthol, and n-tetracosane was spiked onto sand, and extracted with supercritical carbon dioxide, to evaluate the collection efficiency of various solvents and solvent mixtures. Nine single collection solvent systems and four mixed collection solvent systems were studied. When one-component collection solvents were employed, quantitative (above 90%) recovery of all analytes was not possible. With mixed collection solvents, recoveries of 90% or better with all analytes studied were possible.     

Extraction of hydrocarbons from seaweed samples using sonication and microwave-assisted extraction: a comparative study

A sonication method is compared with a microwave-assisted extraction method for recovering polycyclic aromatic hydrocarbons and aliphatic hydrocarbons from seaweed and acid humic samples. Different extracting solvents and adsorbents for the purification step are tested. For the sonication extraction, 10 g of the sample are extracted in an ultrasonic bath (60 degrees C for 15 min with 20 mL of hexane). For the microwave-assisted extraction two steps are carried out, each step at 90 degrees C under pressure in closed vessels with 20 mL of hexane for 10 min at 950 W. A clean-up step is performed for both extraction techniques. The results indicate that the recovery of hydrocarbons is dependent on both the extraction technique and the type of matrix. The most suitable technique appears to be sonication employing hexane as the extraction solvent. The recoveries obtained for aliphatic hydrocarbons are higher than those achieved for the polycyclic aromatic hydrocarbons, with values ranging within 81-109% and 40-76%, respectively.     

Chemically functionalized silica gel with alizarin violet and its application for selective solid-phase extraction of lead from environmental samples

A new material for solid-phase extraction of Pb(II) was prepared using chemically functionalized silica gel with alizarin violet. This material is stable in 6molL(-1) of HCl, 6molL(-1) of H(2)SO(4), common organic solvents and pH 1.0-9.0 aqueous solutions. The influences of analytical parameters including pH of the aqueous solution, amount of the functionalized silica gel, stirring time and flow rates of sample solutions on the quantitative recoveries of Pb(II) were investigated. At the optimum conditions, Pb(II) can be adsorbed with almost 100.0% retention, the adsorption equilibration for Pb(II) was achieved within 15min, and the adsorption capacity of the sorbent for Pb(II) is 3.45mgg(-1) of dry functionalized silica gel. For Pb(II) solution of 10ngmL(-1), the pre-concentration factor is as high as 500, and the recovery is higher than 92%. The new solid-phase extractant has been used for the pre-concentration of low level of Pb(II) in water and soil samples with high recoveries. The standard reference water sample (GSBZ 50009-88(2)) was introduced for accuracy and precision of analytical data.     

微波萃取技术

介绍了在气相／液相色谱测定前的一种新的样品制备技术——微波萃取技术及其所使用的试剂、设备和条件。通过一些数据以及与Ｓｏｘｈｌｅｔ法、超声萃取法比较说明,微波萃取是一种快速、试剂用量少、回收率高、灵敏以及易于自动控制的方法。     

Separation of peptides utilizing ultrahigh-temperature micellar electrokinetic chromatography

The use of ultrahigh column temperatures, up to 110 degrees C, in micellar electrokinetic capillary chromatography was investigated. The number of plates generated per unit time increased from 0.22 to 12.8 plates/s for separations at 15 degrees C and 110 degrees C, respectively. Ultrahigh-temperature micellar electrokinetic capillary chromatography was used for the separation of cyclic undecapeptides (cyclosporins). A minimum resolution of 1.39 was calculated for a critical peak pair at 110 degrees C, which is more than a 50% increase over resolution generated at 40 degrees C. During a run time of more than 90 min at 110 degrees C and at pH 9.3, no sample degradation or solvent boiling was observed.     

重楼中薯蓣皂甙元的反相高效液相色谱测定

采用高效液相色谱法测定了重楼中薯蓣皂甙元的质量分数。样品先经甲醇提取,再经酸水解,将重楼甾体皂甙转变成薯蓣皂甙元,以ＳｙｍｍｅｔｒｙＣ８柱为色谱柱,以Ｖ（乙腈）∶Ｖ（水）＝７５∶２５溶液为流动相,检测波长２０３ｎｍ,重复性较好,结果令人满意。     

Extraction of hydrocarbon contamination from soils using accelerated solvent extraction

Accelerated solvent extraction was studied as a method for the extraction of hydrocarbon contamination from wet and dry soils. Temperatures from 125 to 200 degrees C and six different solvents were investigated. Nonpolar solvents could not achieve complete recovery from wet soils at the temperatures studied. Optimum conditions were found to be 175 degrees C with dichloromethane-acetone (1:1, v/v) with 8 min heat-up time and 5 min static time. Quantitative recoveries for diesel range organics (DROs) and waste oil organics (WOOs) were obtained using the optimized conditions. The recovery of DROs and WOOs from three matrices at two concentrations (5 and 2000 mg/kg) averaged 115%. These results show that accelerated solvent extraction can generate results comparable to those obtained using Soxhlet or sonication.     

Development of a new and environment friendly hollow fiber-supported liquid phase microextraction using vesicular aggregate-based supramolecular solvent

Hollow fiber-based liquid phase microextraction (HF-LPME) using conventional solvents is limited by their relative instability and high volatility. The use of supramolecular solvents as a liquid membrane phase could overcome these inconveniences due to their negligible vapour pressure and high viscosity. In the present study, a novel and highly flexible method was developed based on supramolecular solvents constructed of vesicles of decanoic acid, which were used for the first time as a solvent in HF-LPME. This solvent is produced from the coacervation of decanoic acid aqueous vesicles by the action of tetrabutylammonium (Bu(4)N(+)). In this work, halogenated anilines as model compounds were extracted from water samples into a supramolecular solvent impregnated in the pores and also filled inside the porous polypropylene hollow fiber membrane. The extracted anilines were separated and determined by high-performance liquid chromatography. The technique requires minimal sample preparation time and toxic organic solvent consumption, and provides a significant advantage over conventional analytical methods. The important parameters influencing the extraction efficiency were studied and optimized utilizing two different optimization methods: one variable at a time and the Box-Behnken design. Under the optimum conditions, the preconcentration factors were in the range of 74 to 203. Linearity of the method was obtained in the range of 1.0-100 μg L(-1) with the correlation coefficients of determination (R(2)) ranging from 0.9901 to 0.9986. The limits of detection for the target anilines were 0.5-1.0 μg L(-1). The relative standard deviations varied from 3.9% to 6.0%. The relative recoveries of the three halogenated anilines from water samples at a spiking level of 20.0 μg L(-1) were in the range of 90.4-107.4%.     

Stability of phenolic compounds during extraction with superheated solvents

The stability of nine phenolic compounds in the extraction with superheated methanol at different temperatures (40, 50, 100 and 150 degrees C) has been tested. The evolution of the same compounds in boiling methanol (65 degrees C) in contact with air was also determined. All the assayed phenolic compounds were stable under the extraction conditions with the exception of catechin and epicatechin (recoveries: 87.4% for catechin and 86.0% for epicatechin at 150 degrees C and 94.1% for epicatechin at 100 degrees C). Phenolic compounds kept at the boiling point of methanol (65 degrees C) showed lower recoveries: gentisic acid (85.5%), syringic aldehyde (92.8%), catechin (63.7%) and epicatechin (63.4%). Extraction with superheated solvents was also applied to the extraction of phenolic compounds from solid wastes of the winemaking process.     

Drying dissipative patterns of colloidal crystals of silica spheres in organic solvents

Drying dissipative structural patterns formed in the course of drying colloidal crystals of silica spheres (110 nm in diameter) in water, methyl alcohol, ethyl alcohol, 1-propyl alcohol, diethyl ether, and in the mixtures of ethyl alcohol with the other solvents above have been studied on a cover glass. The macroscopic broad rings were formed in the outside edges of the dried film for all the solvents examined. Furthermore, much distinct broad rings appeared in the inner area when the solvents were ethyl alcohol, methyl alcohol, and their mixtures. Profiles of the thickness of the dried films were sensitive to the organic solvents and explained well with changes in the surface tensions, boiling points, and viscosities of the solvents. The macroscopic and microscopic spoke-like crack patterns formed. The drying area (or the drying time) increased (or decreased) as the surface tension of the solvent decreased. However, the absolute values of these drying parameters are determined also by the boiling points of the solvents. Importance of the fundamental properties of the solvents is supported in addition to the characteristics of colloidal particles in the drying dissipative pattern formation.     

Supercritical fluid extraction and gas chromatography or electroanalysis of metal chelates from different sample matrices

The supercritical fluid extraction of Pb(DDC)2 and MoO2(acac)2 complexes is performed. The previously formed complexes are used in order to simplify the extraction process. In the extraction cell, 9.0 mg of Pb(DDC)2 or 30.0 mg of MoO2(acac)2 is added. With these two complexes, a study of static and dynamic extraction as a function of pressure (1000-2500 psi), temperature (40-160 degrees C), and presence of modifier (methanol) is performed. Under the best conditions, 5.6 mg of Pb(DDC)2 (2.3 mg of Pb2+) is recovered. The parameters are 2500 psi of pressure, 160 degrees C of temperature, 0.5 mL methanol (placed in a 10-mL extraction cell), 60.0 min of static extraction, and 2.0 min of dynamic extraction. It is necessary to add 3.0 mL of methanol to enhance efficiency on the MoO2(acac)2 complex recovery. Quantitative extractions of MoO2(acac)2 (9.0 mg of MoVI) are obtained when the experiments are carried out under 1000-2500 psi of pressure, 140 degrees C, and times no longer than 10.0 min. Then, the study is carried out forming the in situ complexes. For this purpose, metallic ion and ligand are added. Under these conditions, the Pb2+ recovery decreases from 2.3 to 1.9 mg, and the MoVI recovery decreases from 9.0 to 1.0 mg. When 1.9 mg of Pb2+ and 1.0 mg of MoVI or less is placed in the extraction cell, the recoveries are always 100%. The Pb2+ extracts are directly accomplished using gas chromatography-flame ionization detection (GC-FID), and the MoVI extracts are analyzed using GC-FID and catalytic adsorption voltammetry. The quantitation of pure extracts is carried out by constructing calibration curves with complex solutions and sample solutions using the standard addition method. This method is applied by determination of Pb2+ in sodium alginate extracted from algae and blood, urine, and human milk from patients with diagnosed plumbunemy. MoVI is determined in irrigation water and pasture of animal intake.     

Pipette‐tip solid‐phase extraction based on deep eutectic solvent modified graphene for the determination of sulfamerazine in river water

A green and novel deep eutectic solvent modified graphene was prepared and used as a neutral adsorbent for the rapid determination of sulfamerazine in a river water sample by pipette‐tip solid‐phase extraction. Compared with conventional graphene, deep eutectic solvent modified graphene can change the surface of graphene with wrinkled structure and higher selective extraction ability. The properties of deep eutectic solvent modified graphene and graphene were characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, and thermogravimetric analysis. Static adsorption showed deep eutectic solvent modified graphene had a higher adsorption ability (18.62 mg/g) than graphene. Under the optimum conditions, factors such as kinds of washing solvents and elution solvents and volume of elution solvent were evaluated. The limits of detection and quantification were 0.01 and 0.03 μg/mL, respectively. The method recoveries of sulfamerazine were in the range of 91.01–96.82% with associated intraday relative standard deviations ranging from 1.63 to 3.46% and interday relative standard deviations ranging from 0.68 to 3.84%. Deep eutectic solvent modified graphene showed satisfactory results (recovery was 95.38%) and potential for rapid purification of sulfamerazine in river water sample in combination with the pipette‐tip solid‐phase extraction method.     

Boronate affinity adsorption of cis‐diol‐containing biomolecules in nonaqueous solvent

Boronate affinity has attracted much attention in recent years. It has been broadly used for selective isolation and enrichment of cis‐diol‐containing molecules. Conventionally, the cis‐diols are adsorbed in mild alkaline aqueous solutions. In this work, for the first time, we found that boronate affinity adsorption could also be performed in nonaqueous solvent at nonbasic pH. Cis‐diol‐containing compounds present in herbal medicines were used for the adsorption test. The results indicated that all compounds obtained higher recoveries in the organic solvents (methanol, acetonitrile, ethyl acetate) compared with alkaline buffer. The adsorption of vicinal cis‐diol‐containing molecules in organic solvents could be accomplished rapidly, with high selectivity and high recoveries (>80%). These results shed light on the possibility of boronate affinity adsorption in nonaqueous solvents. The results are very important for the isolation and enrichment of cis‐diols, which have poor solubility in water, especially for those in herbal medicines. Copyright © 2015 John Wiley & Sons, Ltd.     

纳米纤维在分析菊酯类农药残留中的应用

以电纺聚苯乙烯纳米纤维作固相萃取材料,对茶叶样品中的拟除虫菊酯农药进行分离富集,用气相色谱-电子捕获器进行检测,并对影响纤维萃取效率的因素进行优化,联苯菊酯、氯菊酯、氰戊菊酯、溴氰菊酯和甲氰菊酯在纳米纤维柱上的最大吸附量分别为7.8、7.5、7.2、6.6、7.0μg/mg,5种农药的3种标准混合液通过纳米纤维小柱后回收率为65.5%～89.0%,RSD为1.2%～3.0%。测定喷洒5种农药后的茶叶样品添加回收率为61.3%～87.1%,RSD为0.9%～2.8%,方法的测定下限为1.0×10-4～1.0×10-2mg/kg。该方法可以满足茶叶中拟除虫菊酯类农药残留检测的要求。     

Determination of fat in dairy products using pressurized solvent extraction

Gravimetric fat data were obtained for a wide range of dairy products with fat contents ranging from 0.5 to 83% using pressurized solvent extraction at elevated temperatures and pressure (80-120 degrees C; 10.3 MPa). Extraction performance was sensitive to solvent composition, temperature, and sample matrix. By optimizing solvent mixtures, sample-solvent contact times of 8-10 min were sufficient for high recoveries from all products tested. The most successful solvents with regard to speed of extraction, selectivity, and recovery (average recovery, %) were various mixtures of hexane (or petroleum ether)-dichloromethane-methanol for dried cream (99.8%), dried whole milk (99.6%), dried buttermilk (98.2%), dried skim milk (97.0%), dried whey protein concentrate (97.5%), casein (95.0%), and caseinate (102.1%); petroleum ether-acetone-ethanol or petroleum ether-acetone-isopropanol for cheddar-type cheese (99.4%); petroleum ether-acetone for butter (99.9%); petroleum ether-acetone-isopropanol for cream (100.3%); and petroleum ether-isopropanol for liquid milks (99.0%). Relative standard deviations for repeatability were obtained for dried whole milk (0.2%), dried whey protein concentrate (0.7%), cheese (0.3%), butter (0.1%), and ultraheat treated (UHT) milk (0.7%). Solvent removal and drying of extracts with a heated block evaporator saved time compared with conventional drying ovens. Estimated savings in labor (50-75%) and solvents (80%) were substantial compared with the manual Mojonnier methods.     

Evaluation of microwave-assisted extraction for the analysis of organophosphorus and pyrethroid pesticides in green onions

The aim of this study was to evaluate the efficiency of microwave-assisted extraction (MAE) for the analysis of organophosphorus (OP) and pyrethroid (PYR) pesticides in green onions by GC/MS. We optimized MAE extraction solvent, temperature, and time by using a certified reference material. As a result, the concentrations of two OP and two PYR target pesticides obtained by MAE with acetonitrile at 110 degrees C for 10 min were in good agreement with certified concentrations and comparable to the results by homogenization used as reference extraction technique. When the recovery test, performed by spiking the target pesticides into blank samples (5.0 g), was carried out with our optimized MAE conditions, mean recoveries of 16 OP and 10 PYR pesticides were 72-108% for a 1.0 pg spiking level and 70-119% for a 0.2 microg level. These results were acceptable according to the validation guideline for testing method of agricultural chemicals in food by Ministry of Health, Labour, and Welfare in Japan. The results suggested that MAE can be used for the analysis of OP and PYR pesticides in green onions.     

Comparative Efficiencies of Trace Metal Extraction from Municipal Incinerator Ashes

Abstract

Five laboratory solvent extraction methods for the determination of leachable trace metals from municipal incinerator fly and bottom ashes are evaluated. The trace elements of interest were cadmium, chromium, copper, manganese and lead. Five different extractants, 0.1NHCl, 1.0 N ammonium acetate, methyl isobutyl ketone (MIBK), chloroform and hexane were used on each ash to determine comparative extraction efficiencies.

Extraction efficiencies of the five solvents were determined based on total metal concentration, and were found to rank in the following order: 0.1NHCl<1.0N ammonium acetate < MIBK < chloroform < hexane. No one solvent was optimal for obtaining environmentally available values for all five metals. The inorganic solvents, 0.1NHCl and 1.0N ammonium acetate, exhibited higher removal of trace metals from ash particles relative to the organic solvents. Manganese concentrations were removed more efficiently by 0.1NHCl, whereas 1.0 N ammonium acetate was more efficient for removing copper concentrations. Cadmium, Cr, and Pb could effectively be extracted by either of the two inorganic solvents. Concentrations of trace metals extracted from refuse ash appeared to be a function of the elemental boiling point and the species that exist on combustion. However, the classification of elements for refuse ash in this study strayed somewhat from the traditional geochemical classification scheme into which coal ash is placed.     

用固相萃取技术富集水中多环芳烃

系统地研究了淋洗剂强度、用量和有机改性剂的加入对固相萃取水中多环芳烃回收率的影响。研究表明,二氯甲烷和苯的洗脱效果较好,回收率为８７％～１０２％;当淋洗剂的用量超过１．５ｍＬ时,对多环芳烃的回收率没有明显的影响;向自来水样中加入２０％有机改性剂可明显改善多环芳烃的回收效果,使回收率达到８９％～１０８％。     

超临界流体萃取环境模拟样品中多环芳烃的收集方法研究

详细系统地研究了收集溶剂的种类、用量及无溶剂固体表面冷冻捕集等方法对离线收集超临界流体萃取多环芳烃组分效率的影响。研究发现,二氯甲烷和丙酮的收集效率较高,其回收率为６１．４４％～１０５．４０％,其它有机溶剂效果较差。而且,当收集溶剂的液面高度大于２．０ｃｍ时,溶剂的用量对收集效率没有明显的影响。玻璃珠固体表面冷冻捕集效果较好,其回收率在６０．９８％～１０９．８８％之间,但其精密度较差,相对标准偏差（ＲＳＤ）在０．２８％～１１．２９％之间。     

蔬果中12种残留农药的亚临界水萃取研究

利用亚临界水可以定量萃取基质中绝大部分化合物的特点,借助加速溶剂萃取仪(ASE)将亚临界水萃取与固相吸附联用,通过在ASE萃取池中填加C18吸附层的方式改进了萃取吸附模式,优化了萃取温度,研究了亚临界水在萝卜、香瓜、苹果和白菜等蔬果基质中对异稻瘟净等12种农药的萃取效果,用气相色谱-串联质谱法(GC-MS/MS)进行检...