Synthesis and thermal decomposition of antimony(III) oxide hydroxide nitrate

The thermal decomposition of the only known antimony nitrate antimony(III) oxide hydroxide nitrate Sb₄O₄(OH)₂(NO₃)₂, whose synthesis routes were reviewed and optimized was followed by TG-DTA under an argon flow, from room temperature up to 750°C. Chemical analysis (for hydrogen and nitrogen) performed on samples treated at different temperatures showed that an amorphous oxide hydroxide nitrate appeared first at 175°C, and decomposed into an amorphous oxide nitrate above 500°C. Above 700°C, Sb₆O₁₃ and traces of -Sb₂O₄ crystallized.Author to whom all correspondence should be addressed     

Thermal decomposition of zinc carbonate hydroxide

This study is devoted to the thermal decomposition of two zinc carbonate hydroxide samples up to 400 °C. Thermogravimetric analysis (TGA), boat experiments and differential scanning calorimetry (DSC) measurements were used to follow the decomposition reactions. The initial samples and the solid decomposition products were analyzed by scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transform infrared (FTIR) and laser particle size analyzer. Results showed that zinc carbonate hydroxide decomposition started at about 150 °C and the rate of decomposition became significant at temperatures higher than 200 °C. The apparent activation energies (E_a) in the temperature range 150–240 °C for these two samples were 132 and 153 kJ/mol. The XRD analyses of the intermediately decomposed samples and the DSC results up to 400 °C suggested a single-step decomposition of zinc carbonate hydroxide to zinc oxide with not much change in their overall morphologies.     

Preparation and thermal decomposition of indium hydroxide

Summary Indium hydroxides were prepared by the mixing of aqueous indium nitrate solution with sodium or ammonium hydroxide solutions under various conditions. The thermal decomposition of the resulting materials was examined by thermogravimetry, differential thermal analysis, X-ray diffraction study and infrared spectroscopy. It has been found that sodium hydroxide solution is more suitable than the addition of ammonium hydroxide solution to prepare indium hydroxide in well crystallization; the thermal decomposition of indium hydroxide, in which the composition is In(OH)₃·xH₂O where x￡2, proceeds according to the following process: In(OH)₃·xH₂O?cubic In(OH)₃?cubic In₂O₃     

氢氧化镁分解动力学的研究

以硼泥为原料与硫酸反应制备出七水硫酸镁,以氢氧化钠为沉淀剂制备出符合标准HG/T 3607-2000的氢氧化镁.利用XRD,SEM和TEM对氢氧化镁进行了表征,DTA-TG对氢氧化镁的热分解动力学进行了研究.XRD结果表明:制备粉体为单一Mg(OH)2.SEM和TEM结果表明:样品为片状或针状纤维,片直径大小不一,在20～50 nm之间,针状纤维形状不规则,大小不一致,长度在20～100 nm之间.利用Kissinger法和Ozawa法计算出的氢氧化镁热分解反应活化能分别为135.14和141.61 kJ·mol-1.利用Coats-Redfern法和Dolye法判断氢氧化镁热分解反应机理函数为A1.5.     

Effect of water vapor on the thermal decomposition process of zinc hydroxide chloride and crystal growth of zinc oxide

Thermal decomposition process of zinc hydroxide chloride (ZHC), Zn₅(OH)₈Cl₂·H₂O, prepared by a hydrothermal slow-cooling method has been investigated by simultaneous X-ray diffractometry and differential scanning calorimetry (XRD-DSC) and thermogravimetric-differential thermal analysis (TG-DTA) in a humidity-controlled atmosphere. ZHC was decomposed to ZnO through β-Zn(OH)Cl as the intermediate phase, leaving amorphous hydrated ZnCl₂. In humid N₂ with P_H2O=4.5 and 10 kPa, the hydrolysis of residual ZnCl₂ was accelerated and the theoretical amount of ZnO was obtained at lower temperatures than in dry N₂, whereas significant weight loss was caused by vaporization of residual ZnCl₂ in dry N₂. ZnO formed by calcinations in a stagnant air atmosphere had the same morphology of the original ZHC crystals and consisted of the c-axis oriented column-like particle arrays. On the other hand, preferred orientation of ZnO was inhibited in the case of calcinations in 100% water vapor. A detailed thermal decomposition process of ZHC and the effect of water vapor on the crystal growth of ZnO are discussed.     

Synthesis and characterization of ZnO nanoparticles by thermal decomposition of a curcumin zinc complex

ZnO nanoparticles were generated by thermal decomposition of a binuclear zinc (II) curcumin complex as single source precursor. Thermal behavior of the precursor showed a considerable weight loss at about 374 °C by an exothermic reaction with a maximum weight loss rate of 14%/min. Complete decomposition of precursor was observed within 49 min with a heating rate of 10 °C/min. Synthesized nanoparticles have been characterized by X-ray diffraction, Fourier transform infrared spectroscopy, transmission electron microscopy and selected area electron diffraction microscopy. Results revealed monodispersed hexagonal zincite structure with an average size of 117 ± 4 nm.     

Studies on the intercalation of naproxen into layered double hydroxide and its thermal decomposition by in situ FT-IR and in situ HT-XRD

Layered double hydroxides, novel anionic clay, meet the first requirement as inorganic matrices for encapsulating functional drugs or biomolecules with negative charge in aqueous media. In this study, naproxen has been intercalated into Mg-Al layered double hydroxide by the methods of ion exchange. The structure and composition of the intercalated material have been studied by X-ray diffraction (XRD), UV-vis spectroscopy and inductively coupled plasma emission spectroscopy. A schematic model has been proposed. Furthermore, in situ Fourier transform infrared spectroscopy, in situ high-temperature XRD, and thermogravimetry (TG) have been used to characterize the thermal decomposition of the hybrid material. It has been found that the thermal stability of the intercalated naproxen is significantly enhanced compared with the pure form before intercalation, which suggests that this drug-inorganic layered material may have prospective application as the basis of a novel drug delivery system.     

Structure and thermal decomposition of sulfated β-cyclodextrin intercalated in a layered double hydroxide

The sodium salt of hexasulfated β-cyclodextrin has been synthesized and intercalated into a magnesium-aluminum layered double hydroxide by ion exchange. The structure, composition and thermal decomposition behavior of the intercalated material have been studied by variable temperature X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), inductively coupled plasma emission spectroscopy (ICP), and thermal analysis (TG-DTA) and a model for the structure has been proposed. The thermal stability of the intercalated sulfated β-cyclodextrin is significantly enhanced compared with the pure form before intercalation.     

The thermal decomposition of zirconium oxyhydroxide

The thermal decomposition of zirconium oxyhydroxides prepared by the mixture of aqueous zirconium oxychloride solutions and aqueous solutions of sodium hydroxide or ammonium hydroxide under various conditions has been examined by thermogravimetry, differential thermal analysis, X-ray diffraction study and infrared spectrophotometry. As a result, it is seen that the thermal decomposition of zirconium oxyhydroxide, in which the composition is ZrO_2-x(OH)_2xyH₂O where x2 and 1y<2, proceeds according to the following process:

Structural and thermal study of calcium undecanoate

In the present work, an X-ray diffraction (XRD) and thermal study of calcium undecanoate is presented. The measured high-resolution XRD powder pattern of the synthesized salt at room temperature, using synchrotron radiation, showed that the salt is a mixture of monohydrated and anhydrous calcium undecanoate. Calcium undecanoate monohydrate proved to have a monoclinic cell with a symmetry described by the P2₁/a space group. The structure dehydrates at about 100°C. After dehydration, the salt undergoes a phase transformation which results in a thermotropic mesophase. Further heating of the salt leads to decomposition and melting. Ketones are the probable products of decomposition at 400°C.     

Effect of atmosphericwater vapor on the kinetics of thermal decomposition of copper(II) carbonate hydroxide

The effect of atmospheric water vapor on the kinetic rate behavior of the thermal decomposition of copper(II) carbonate hydroxide, Cu₂CO₃(OH)₂, was investigated by means of TG-DTA coupled with a programmable humidity controller. With increasing water vapor pressure p(H₂O) from 0.8 to 10.6 kPa, a systematic reduction of the reaction temperature of the thermal decomposition was observed as the continuous trend from the previous works at the lower p(H₂O). Through a comparative kinetic analysis of the reaction at different p(H₂O), a catalytic action of the atmospheric water vapor on the nucleation process at the first half of the reaction was identified as the possible origin of the reduction of the reaction temperature.     

Structural characterization and thermal decomposition of layered double hydroxide/poly(p-dioxanone) nanocomposites

Nanocomposites based on layered double hydroxides (LDH) and poly(p-dioxanone) (PPDO) were prepared by melt processing using dodecylbenzene sulfonate (DBS) and 4-hydroxybenzene sulfonate (HBS) as organic modifiers. The incorporation of organic anions in LDH was demonstrated by wide-angle X-ray scattering (WAXS) and Fourier transform infrared (FTIR). The dispersion degree of the organically modified LDHs in the PPDO matrix was analyzed by WAXS, indicating that only the LDH modified with HBS was exfoliated. The effect of the organically modified LDHs on the thermal stability of PPDO was studied using thermogravimetric analysis (TGA). The thermal stability of PPDO matrix was enhanced by the incorporation of the LDH modified with HBS due to the shielding effect of the exfoliated layers. In contrast, the LDH modified with DBS produced a decrease of the thermal stability of PPDO, probably due to hydrolytic decomposition of ester group. The thermogravimetric analysis also showed that the organo-modified LDH did not modify the thermal decomposition mechanism of the polymer, but had an effect on the thermal stability.     

Preparation, crystal structure and thermal decomposition study of some trimethylsilyl esters of dicarbamic acids

Some new trimethylsilylated dicarbamic acid esters 1–9 and 10 were prepared. Their thermal decomposition was studied in n-alkanes as media. The reactions were monitored by gas chromatography (GC) and gas chromatography-mass spectrometry (GC-MS), respectively. Some N-silylated cyclic ureas 11–15 were also prepared from the corresponding esters 2–6 by thermolysis. The crystal structures of 2, 5 and 8 are also discussed. The crystal and molecular structures of 2 and 5 have very similar characteristics. Both molecules are sited via their molecular centre of symmetry on crystallographic inversion centres. The Carbamate groups are planar in all three cases as expected. An analysis of the data showed that the force due to Si---O conjugation which constrains the Si atom into the plane of the carbamate group is comparable to the crystal packing forces with a small out-of-plane movement being not unfavourable.     

Structural and thermal interpretation of the synergy and interactions between the fire retardants magnesium hydroxide and zinc borate

The mechanism of cooperative action of commercial fire retardants is interpreted as resulting from specific chemical reaction and phase changes. This investigation focuses on the thermally initiated interactions between two forms of commercially available fire retardant compounds. The fire performance of a polyolefin with a metal hydroxide fire retardant, magnesium hydroxide, can significantly reduce the heat release rate through absorption of heat during conversion to its metal oxide. Formation of water, followed by vaporisation, decreases heat and dilutes volatiles from polymer degradation. The second form of fire retardant compounds are zinc borates (2ZnO·3B₂O₃·3H₂O and 4ZnO·B₂O₃·H₂O), that undergo dehydration with increasing temperature. Differential thermal analysis and wide-angle X-ray spectroscopy indicated that various structural changes occurred during heating. Endothermic transitions were observed for all components, while zinc borate (2ZnO·3B₂O₃·3H₂O) showed an exothermic crystallisation transition at relatively high temperature. The exotherm was modified by the development of a new crystalline phase, magnesium orthoborate (3MgO·B₂O₃) that formed on reaction with magnesium oxide (MgO) at temperatures greater than 500 °C. Formation of crystalline zinc oxide (ZnO) was also detected. From zinc borate (4ZnO·B₂O₃·H₂O), ZnO was primarily formed. No new crystalline phases were observed in the presence of MgO over the temperature range investigated.     

Quantitative studies on the preparation of colloidal particles of cobalt hydroxide by the moving chemical reaction boundary method in agarose gel

Quantitative investigations were performed for the synthesis of colloidal particles of cobalt hydroxide in agarose gel by the moving chemical reaction boundary method . The experimental results show that: (1) the sizes of the colloidal particles can be controlled by changing the concentration of agarose gel, (2) the concentration of the colloidal particles is also controlled by changing the concentrations of CoCl₂ and/or NaOH, and (3) most importantly, the concentration of colloidal particles can be predicted with the theory of moving chemical reaction boundary (MCRB). The colloidal particles prepared by the MCRB are amorphous and are more easily oxidized than particles prepared by other methods.     

Synthesis, structure, solid-state thermal decomposition and magnetic properties of binuclear Nd, Gd and Eu cymantrenecarboxylates

New rare-earth cymantrenecarboxylates [Nd₂(μ₂-OOCCym)₄(OOCCym)₂(THF)₄] (1) and [Ln₂(μ₂-OOCCym)₄(OOCCym)₂(THF)₄]·THF (Ln = Gd (2), Eu (3); Cym = (η⁵-C₅H₄)Mn(CO)₃) were synthesized starting from carboxycymantrene and lanthanide nitrates, and characterized by X-ray diffraction. The crystals of 1-3 consist of isolated binuclear molecules; the Ln atoms are eight-coordinate. The magnetic properties of 2 are indicative of antiferromagnetic coupling between the Gd atoms at liquid helium temperature. The thermal decomposition of complexes 1-3 was studied by differential scanning calorimetry (DSC) and thermogravimetry (TG). According to the X-ray powder diffraction patterns, the thermal decomposition of the complexes in air affords a mixture of LnMn₂O₅ and Mn₂O₃ as the final products.     

Preparation of nano-Co3O4-coated Albizia procera-derived carbon by direct thermal decomposition method for electrochemical water oxidation

It is obtained that nano-Co₃O₄-coated carbon prepared by thermal decomposition of Co(NO₃)₂·6H₂O at 300 °C on home-made Albizia procera (Roxb.) leaves derived carbon is an efficient electrocatalyst for electrochemical water oxidation in 0.1 M NaOH (aq.) solution. The loading of nano-Co₃O₄ on the carbon was changed by varying the amount of precursor of cobalt (100–1000 mg) and using a constant amount of the carbon (200 mg) during thermal decomposition. The prepared samples were characterized by physical techniques, including X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), thermo-gravimetric analysis (TGA), fourier transform infrared spectroscopy (FTIR), high-resolution transmission electron microscopy (HRTEM), diffuse reflectance spectroscopy (DRS), Brunauer-Emmett-Teller (BET) and X-ray photoelectron spectroscopy (XPS). XRD, TEM, FESEM, and EDS confirmed the formation of uniformly distributed nanoparticles of single-phase Co₃O₄ on the surface of carbon. The XRD data reveals formation of nano-Co₃O₄ with average particle sizes in the range of 9–17 nm. The FESEM micrographs demonstrate that Co₃O₄ nanoparticles, having irregular morphology, are uniformly and densely covered on the surface of supporting carbon.. The prepared samples were immobilized on the filter paper derived carbon electrode (FPCE) to study their electrocatalytic properties toward water oxidation. The cyclic voltammetric studies showed that the nano-Co₃O₄-C prepared using 400 mg of Co(NO₃)₂·6H₂O (nano-Co₃O₄-C-400), which possesses meso- and macropores with BET surface area of 192.4 m²/g, reaches a current density of 28 mAcm⁻² at 1.5 V and electrochemical water oxidation starting potential of 0.7 V. In this work, it is also shown that the current densities, at 1.5 V, increase by increasing the amount of cobalt oxide in the prepared samples though. The nano-Co₃O₄-C-400 catalyst shows optimum performance for electrochemical water oxidation in terms of starting water oxidation potential, reasonable amount of Co₃O₄ and moderate level of current density at 1.5 V.     

The effect of Zn, Al layered double hydroxide on thermal decomposition of poly(vinyl chloride)

Poly(vinyl chloride)/layered double hydroxide (LDH) composite was prepared by mixing 4 wt% Zn₂Al-CO₃-LDH with PVC and fluxing at 180 °C. The thermal decomposition behaviour of the LDH + PVC composite in air and nitrogen environments was systematically investigated. We found that mixing Zn₂Al-CO₃-LDH into PVC facilitates dehydrochlorination from ca. 300 to 270 °C but reduces the reaction extent to leave more chlorine on the polyene backbones both in air and N₂. We have also found that at 400-550 °C, both in air and N₂, LDH assists the formation of char-like materials and decreases the release of volatile hydrocarbons. From 550 to 800 °C, the char-like materials are mostly retained in N₂ while they are almost completely thermo-oxidized (burned) in air. Thus, addition of Zn₂Al-CO₃-LDH to PVC does not increase the thermal stability, but does promote charring to retard the generation of flame. The influence of LDH on PVC thermal properties has been also addressed mechanically.     

The evolution of structural changes in ettringite during thermal decomposition

The thermal decomposition of ettringite, Ca₆[Al(OH)₆]₂(SO₄)₃·∼26H₂O, was studied with pulsed neutron time-of-flight diffraction combined with Rietveld structure refinement. Like prior investigations, transition from a crystalline to amorphous state occurred following the loss of ∼20 water molecules. In contrast to earlier investigations, which relied upon indirect measurements of water and hydroxyl occupancies, the present study inferred the occupancies directly from Rietveld crystal structure refinement of the diffraction data. The decomposition pathway was shown to be more complex than previously envisioned, involving the simultaneous loss of hydroxyl and water molecules. Nuclear magnetic resonance (NMR) spectroscopy studies of the rigid lattice lineshapes of fully and partially hydrated ettringite were performed and confirmed our decomposition model.     

Synthesis, characterization and activity of alumina-supported cobalt nitride for NO decomposition

A new type of transition metal nitride, viz. alumina-supported cobalt nitride, was synthesized for the first time by NH₃-temperature-programmed reaction, and its structure was characterized by BET, X-ray diffraction (XRD) and X-ray photoelectron spectroscopic (XPS) techniques. The supported cobalt nitride performs much better than its bulk counterpart for NO decomposition, owing to its small crystal size, high thermal stability and big surface area.