Transformation of ferrihydrite in the presence or absence of trace Fe(II): The effect of preparation procedures of ferrihydrite

Two-line ferrihydrite was prepared by two different procedures. In procedure 1, which is widely used, ferrihydrite (named as ferrihydrite-1) was prepared by droping NaOH solution into Fe(III) solution. In procedure 2, which is rarely reported, ferrihydrite (named as ferrihydrite-2) was prepared by adding Fe(III) and NaOH solutions into a certain volume of water simultaneously. The results showed that mixing procedures of Fe(III) and alkaline were critical in the sub-microstructures and the conversion mechanisms of ferrihydrites in the presence or absence of trace Fe(II). The sub-microstructure of ferrihydrite-1 favored the mechanism of its dissolution re-crystallization and hematite nanoparticles with rough surface were obtained. The sub-microstructure of ferrihydrite-2 favored the solid state transformation from ferrihydrite to hematite and hematite nanoparticles with smooth surface were formed. These research results will be helpful for us to control the synthesis of hematite nanoparticles with different surface state.     

Ferrihydrite的亚微观结构对反应活性的影响

以Fe(III)盐为原料、NaOH为沉淀剂、采用三种方法调控制备了ferrihydrite, 借助X射线衍射(XRD)、红外光谱(IR)、差热分析(DTA)及其在稀盐酸中的溶解速率等手段对其结构进行了表征, 探讨了ferrihydrite的形成环境对其亚微观结构及其反应活性的影响. 结果表明, 不同方法制备的ferrihydrite的亚微观结构不同, 恒pH条件下制备的ferrihydrite结构与α-Fe2O3结构最为相似, 更易转化为α-Fe2O3粒子.     

Phase transformation of boron nitride under hypothermal conditions

Phase transformation among different boron nitride (BN) phases in hydrothermal solution was investigated. It was found that hexagonal boron nitride (hBN) firstly formed in the solution at relatively low temperature (i.e., 220 °C). After that, a spot of hBN began to transform into wurtzite boron nitride (wBN) and cubic boron nitride (cBN) at 230 °C. More and more hBN converted into wBN and cBN with the increase in temperature, and this transformation process completed at 300 °C. In this paper, we have explained the mechanism of the above phase transformation by using a reported “puckering mechanism”.     

Dechlorination of poly(vinylidene chloride) in NaOH/ethylene glycol as a function of NaOH concentration, temperature, and solvent

The wet dechlorination treatment of poly(vinylidene chloride) (PVDC) was evaluated at atmospheric pressure in a solution of NaOH in ethylene glycol (EG), as a function of NaOH concentration, temperature, and solvent. Hydroxide ion from NaOH was required for dechlorination with EG acting solely as a solvent. The wet treatment exhibited significantly enhanced dechlorination efficiency over traditional thermal techniques, with a reaction efficiency as high as 92.8% in 1.0 M NaOH at 190 °C. Dechlorination reactions of PVDC in both NaOH/EG and NaOH/H₂O were expressed by an apparent first-order reaction. At 190 °C, the apparent rate constant in 1.0 M NaOH/EG was approximately 1.4 times larger than in 1.0 M NaOH/H₂O, with an apparent activation energy of 82.8 kJ mol⁻¹, indicating that the reaction proceeded under chemical control. The degree of dechlorination increased with increasing reaction temperature, favouring the elimination of HCl over the hydroxyl substitution of chloride.     

Studies on fluoride adsorption capacities of amorphous Fe/Al mixed hydroxides from aqueous solutions

This study evaluated the effectiveness of amorphous iron and aluminum mixed hydroxides in removing fluoride from aqueous solutions. A series of mixed Fe/Al samples were prepared at room temperature by co-precipitating Fe and Al mixed salt solutions at pH 7.5. The compositions (Fe:Al molar ratio) of the oxides were varied as 1:0, 3:1, 2:1, 1:1 and 0:1 and the samples were characterized by XRD, BET surface area and pH_ZPC. The XRD studies indicated the amorphous nature of the samples and Al(III) incorporation on Fe(III) hydroxides. Batch adsorption studies for fluoride removal on these materials showed that the adsorption capacities of the materials were highly influenced by solution pH, temperature and initial fluoride concentration. The rate of adsorption was fast and equilibrium was attained within 2 h. The adsorption followed first-order kinetics with intraparticle diffusion as the rate determining step for all the samples. The experimental data fitted well to both Langmuir and Freundlich adsorption isotherms. All samples exhibited very high Langmuir adsorption capacities; the sample with molar ratio 1 has shown maximum adsorption capacity of 91.7 mg/g. The thermodynamic parameters were determined to study the feasibility of the adsorption process.     

Evaluation of retention and release processes of two antibiotics from the biocompatible core-shell microparticles

By dropwise addition of a chitosan solution into different non-solvent, such as: 1 N and 2 N NaOH as well as 1 N NaOH: C₂H₅OH mixture (2:1, v/v) at temperature of 25 °C and 50 °C under stirring, the spherical pure chitosan microparticles were performed. As solvents for chitosan was used 0.1 N acetic acid or 0.1 N HCl. The immersion of the pure chitosan microparticles in hyaluronan solution led to complex microparticles, namely chitosan microparticles covered by a hyaluronan layer. For all the microparticles performed the behaviours in the retention process of two antibiotics: chloramphenicol succinate sodium salt and cefotaxime sodium salt were analyzed. Also, the study shows the release behaviour of cefotaxime sodium salt by the microparticles loaded with this drug. Among the microparticles performed a type of complex microparticles can be considered a suitable drug delivery system for cefotaxime. These microparticles were performed by dropwise addition of chitosan solution in 0.1 N acetic acid into the 1 N NaOH: C₂H₅OH (2:1, v/v) non-solvent at 20 °C for 3 h, followed by their washing up to alkalinity loss and the immersion in hyaluronan solution of 10 g/L concentration for 24 h.     

Development of analytical method for determination of Sb(V), Sb(III) and TMSb(V) in occupationally exposed human urine samples by HPLC-HG-AFS

In the present paper, we develop a methodology for antimony speciation in occupationally exposed human urine samples by high-performance liquid chromatography with hydride generation atomic fluorescence spectrometry (HPLC-HG-AFS). The methodology was applied to the determination of Sb(V), Sb(III) and (CH₃)₃SbCl₂ (TMSb(V)). Retention time of Sb(V), Sb(III) and TMSb(V) species were 0.88, 2.00 and 3.61 and the detection limits were 0.18, 0.19 and 0.12 μg L^− 1, for 100 μL loop injection respectively which is considered useful for elevated/occupationally exposed urine samples. Studies on the stability of antimony species in urine samples on the function of the elapsed time of preservation (4 °C) and storage (− 70 °C) were performed. Results revealed that antimony species are highly unstable at − 70 °C, probably due to co-precipitation reaction. In this kind of matrix transformation during preservation time may occur, such as oxidation of Sb(III) to Sb(V) and transformation into species that do not elute from the column. EDTA shows that it is able to stabilize Sb(III) for more than one week of preservation time at 4 °C avoiding co-precipitation during storage at − 70 °C. Finally the methodology was applied to occupationally exposed human urine samples. 25% of specimens present antimony levels (Sb(V)) of more than 5 μg L^− 1.     

Fe(II)-induced transformation from ferrihydrite to lepidocrocite and goethite

The transformation of Fe(II)-adsorbed ferrihydrite was studied. Data tracking the formation of products as a function of pH, temperature and time is presented. The results indicate that trace of Fe(II) adsorbed on ferrihydrite can accelerate its transformation obviously. The products are lepidocrocite and/or goethite and/or hematite, which is different from those without Fe(II). That is, Fe(II) not only accelerates the transformation of ferrihydrite but also leads to the formation of lepidocrocite by a new path. The behavior of Fe(II) is shown in two aspects—catalytic dissolution-reprecipitation and catalytic solid-state transformation. The results indicate that a high temperature and a high pH(in the range from 5 to 9) are favorable to solid-state transformation and the formation of hematite, while a low temperature and a low pH are favorable to dissolution-reprecipitation mechanism and the formation of lepidocrocite. Special attentions were given to the formation mechanism of lepidocrocite and goethite.     

Chemically-modified activated carbon with ethylenediamine for selective solid-phase extraction and preconcentration of metal ions

A new method that utilizes ethylenediamine-modified activated carbon (AC-EDA) as a solid-phase extractant has been developed for simultaneous preconcentration of trace Cr(III), Fe(III), Hg(II) and Pb(II) prior to the measurement by inductively coupled plasma optical emission spectrometry (ICP-OES). The new sorbent was prepared by oxidative surface modification. Experimental conditions for effective adsorption of trace levels of Cr(III), Fe(III), Hg(II) and Pb(II) were optimized with respect to different experimental parameters using batch and column procedures in detail. The optimum pH value for the separation of metal ions simultaneously on the new sorbent was 4.0. Complete elution of absorbed metal ions from the sorbent surface was carried out using 3.0 mL of 2% (%w/w) thiourea and 0.5 mol L⁻¹ HCl solution. Common coexisting ions did not interfere with the separation and determination of target metal ions. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 39.4, 28.9, 60.5 and 49.9 mg g⁻¹ for Cr(III), Fe(III), Hg(II) and Pb(II), respectively. The time for 94% adsorption of target metal ions was less than 2 min. The detection limits of the method was found to be 0.28, 0.22, 0.09 and 0.17 ng mL⁻¹ for Cr(III), Fe(III), Hg(II) and Pb(II), respectively. The precision (R.S.D.) of the method was lower 4.0% (n = 8). The prepared sorbent as solid-phase extractant was successfully applied for the preconcentration of trace Cr(III), Fe(III), Hg(II) and Pb(II) in natural and certified samples with satisfactory results.     

Dechlorination of poly(vinyl chloride) using NaOH in ethylene glycol under atmospheric pressure

A solution of NaOH dissolved in ethylene glycol (EG) was effective in the dechlorination of poly(vinyl chloride) (PVC) at atmospheric pressure. The degree of dechlorination increased with increasing temperature, reaching a maximum of 97.8% at 190 °C. The dechlorination proceeded under chemical control and exhibited first-order kinetics with an apparent activation energy of 170 kJ mol⁻¹. The apparent rate constant for dechlorination in 1.0 M NaOH/EG was approximately 150 times greater than that in 1.0 M NaOH/H₂O. In addition, dechlorination was faster at atmospheric pressure in NaOH/EG than under high pressure in NaOH/H₂O. The dechlorination reaction occurs via a combination of E2 and S_N2 mechanisms.     

Effects of hydrothermal post-treatment on microstructures and morphology of titanate nanoribbons

Titanate nanoribbons were prepared via a hydrothermal treatment of rutile-type TiO₂ powders in a 10 M NaOH solution at 200 °C for 48 h. The as-prepared titanate nanoribbons were then hydrothermally post-treated at 150 °C for 12-36 h. The titanate nanoribbons before and after hydrothermal post-treatment were characterized with FESEM, XRD, TEM, UV-VIS and nitrogen adsorption-desorption isotherms. The results showed that the hydrothermal post-treatment not only promoted the phase transformation from titanate to anatase TiO₂, but also was beneficial to the removal of Na⁺ ions remained in the titanate nanoribbons. After hydrothermal post-treatment, the TiO₂ samples retained the one-dimensional structure feature of the titanate nanoribbons and showed an obvious increase in the specific surface area and the pore volume.     

Nanometer SiO2 modified with 5-sulfosalicylic acid as selective solid-phase extractant for Fe(III) determination by ICP-AES from biological and natural water samples

A new modified nanometer SiO₂ using 5-sulfosalicylic acid (SSA) as a solid-phase extractant was used for separation, preconcentration and determination of Fe(III) in aqueous solutions by inductively coupled plasma atomic emission spectrometry (ICP-AES). Its adsorption and preconcentration behaviour for Fe(III) in aqueous solutions was investigated using static procedures in detail. The optimum pH value for the separation of Fe(III) on the newly designed sorbent was 3.5. Complete elution of the adsorbed Fe(III) from the nanometer SiO₂-SSA was carried out using 2.0 mL of 0.01 mol L^− 1 of HCl. The time of 90% sorption was less than 2 min for Fe(III) at pH 3.5. Common coexisting ions did not interfere with the separation and determination of Fe(III) at pH 3.5. The maximum static adsorption capacity of the sorbent at optimum conditions was found to be 44.01 mg of Fe(III) per gram of sorbent. The relative standard deviation (RSD) of the method under optimum conditions was 3% (n = 5). The procedure was validated by analyzing three certified reference materials (GBW 08301, GBW 08504, GBW 08511), the results obtained were in good agreement with standard values. The nanometer SiO₂-SSA was successfully employed in the separation and preconcentration of the investigated Fe(III) from the biological and natural water samples yielding 100-folds concentration factor.     

Influence of arsenate species on the formation of Fe(III) oxyhydroxides and Fe(II–III) hydroxychloride

Iron(III) oxyhydroxides were prepared by oxidation of aerated aqueous suspensions of Fe(II) hydroxide. The effects of arsenate species on their formation were studied by mixing FeCl₂·4H₂O, NaOH and Na₂HAsO₄ solutions. The intermediate and final products of the oxidation processes were characterised by X-ray diffraction, Infrared and Raman spectroscopy. Arsenate species were not reduced during the process but they influenced both oxidation stages, that is the formation of the intermediate Fe(II–III) compound and its subsequent oxidation into Fe(III) compounds. Arsenate species clearly inhibited the growth and hindered the crystallisation of GR(Cl^?), the Fe(II–III) hydroxychloride that would have formed in the experimental conditions considered here. For the largest arsenate concentrations, the intermediate product was nanocrystalline and more likely consisted of clusters showing an ordering of atoms similar to that of GR(Cl^?), isolated from each other by adsorbed arsenate species. The adsorption of As(V) prevented growth of these clusters into well-crystallised GR(Cl^?). The arsenate species influenced similarly the second reaction stage by inhibiting the formation of well-ordered and crystallised Fe(III) compounds. Lepidocrocite, the final product in the absence of arsenate, was replaced by “6-line” ferrihydrite with increasing As(V) concentration, then “6-line” ferrihydrite was replaced by another poorly ordered compound, feroxyhite. These crystallised compounds were obtained together with an increasing part of nanocrystalline Fe(III) ox(yhydrox)ide(s).     

Subcritical water extraction of organic matter from sedimentary rocks

Subcritical water extraction of organic matter containing sedimentary rocks at 300 °C and 1500 psi produces extracts comparable to conventional solvent extraction. Subcritical water extraction of previously solvent extracted samples confirms that high molecular weight organic matter (kerogen) degradation is not occurring and that only low molecular weight organic matter (free compounds) are being accessed in analogy to solvent extraction procedures. The sedimentary rocks chosen for extraction span the classic geochemical organic matter types. A type I organic matter-containing sedimentary rock produces n-alkanes and isoprenoidal hydrocarbons at 300 °C and 1500 psi that indicate an algal source for the organic matter. Extraction of a rock containing type II organic matter at the same temperature and pressure produces aliphatic hydrocarbons but also aromatic compounds reflecting the increased contributions from terrestrial organic matter in this sample. A type III organic matter-containing sample produces a range of non-polar and polar compounds including polycyclic aromatic hydrocarbons and oxygenated aromatic compounds at 300 °C and 1500 psi reflecting a dominantly terrestrial origin for the organic materials. Although extraction at 300 °C and 1500 psi produces extracts that are comparable to solvent extraction, lower temperature steps display differences related to organic solubility. The type I organic matter produces no products below 300 °C and 1500 psi, reflecting its dominantly aliphatic character, while type II and type III organic matter contribute some polar components to the lower temperature steps, reflecting the chemical heterogeneity of their organic inventory. The separation of polar and non-polar organic compounds by using different temperatures provides the potential for selective extraction that may obviate the need for subsequent preparative chromatography steps. Our results indicate that subcritical water extraction can act as a suitable replacement for conventional solvent extraction of sedimentary rocks, but can also be used for any organic matter containing mineral matrix, including soils and recent sediments, and has the added benefit of tailored extraction for analytes of specific polarities.     

Fe(II) hydroxycarbonate Fe2(OH)2CO3 (chukanovite) as iron corrosion product: Synthesis and study by Fourier Transform Infrared Spectroscopy

Fe(II) compounds were precipitated by mixing FeCl₂ · 4H₂O, NaOH and Na₂CO₃ · 10H₂O solutions and the influence of the concentration ratios R = [FeCl₂ · 4H₂O]/[NaOH] and R′ = [Na₂CO₃ · 10H₂O]/[NaOH] on the nature of the precipitates was studied. The conditions favouring the formation of chukanovite Fe₂(OH)₂CO₃ at the detriment of Fe(II) hydroxide Fe(OH)₂, often considered as the first solid forming from the Fe(II) dissolved species generated by the dissolution of steel, were determined. Chukanovite was the unique compound to form for R > 1 and R′ > 0.5. When one of these conditions was not met, that is when the amount of Fe(II) dissolved species or the amount of carbonate species was not sufficient, Fe(OH)₂ was precipitated together with chukanovite. For the smallest values of R and R′, 0.6 and 0.1, respectively, chukanovite was not obtained. However, it was demonstrated that ageing at room temperature of a carbonate-containing suspension of Fe(OH)₂ could lead to the total transformation of Fe(II) hydroxide into chukanovite. The Fe(II) compounds were analysed by ATR/FT-IR spectroscopy under inert atmosphere, since this method allowed us to distinguish unambiguously Fe₂(OH)₂CO₃ from Fe(OH)₂. As a result, chukanovite could also be identified by infrared micro-spectroscopy inside the rust layers of an archaeological iron nail extracted from a soil presenting anoxic conditions.     

The transformation of ferrihydrite in the presence of trace Fe(II): The effect of the ammonia, amine and the coordination ions of Fe(III)

This work examined Fe(II)-induced transformation of ferrihydrite in the presence of ammonia, amine and the coordination ions of Fe(III). Our earlier results showed that ferrihydrite transformed into the mixture of lepidocrocite, goethite and/or hematite in the presence of trace Fe(II) and absence of ammonia and similar species. However, the formation of lepidocrocite was restrained when using ammonia as precipitants. When introducing some amines (e.g. ethanolamine and diethanolamine) and some coordination ions (e.g. F⁻ and ions) into the reaction system, a similar effect on the transformation of ferrihydrite was found. Probably, the complexes formed between Fe(III) and those additives favor the formation of goethite. At the same time, the introduction of these additives hinders Fe(II) from interacting with ferrihydrite, which makes the catalytic dissolution of ferrihydrite be limited, thus, the formation of lepidocrocite be restrained.     

Syntheses of TiO2(B) nanowires and TiO2 anatase nanowires by hydrothermal and post-heat treatments

TiO₂(B) nanowires and TiO₂ anatase nanowires were synthesized by the hydrothermal processing in 10 M NaOH aq. at 150 °C followed by the post-heat treatment at 300-800 °C. As-synthesized Na-free titanate nanowires (prepared by the hydrothermal treatment and repeated ion exchanging by HCl (aq.) were transformed into TiO₂(B) structure with maintaining 1-D morphology at 300-500 °C, and further transformed into anatase structure at 600-800 °C with keeping 1-D shape. At 900 °C, they transformed into rod-shaped rutile grains. Microstructure of these 1-D TiO₂ nanomaterials is reported.     

Electron-beam irradiation on poly(propylene carbonate) in the presence of polyfunctional monomers

Poly(propylene carbonate) (PPC) showed predominantly degradation under electron-beam irradiation, accompanied by deterioration of its mechanical performance due to sharp decrease of the molecular weight. Crosslinked PPC was prepared by addition of polyfunctional monomer (PFM) to enhance the mechanical performance of PPC. When 8 wt% of PFM like triallyl isocyanurate (TAIC) was added, crosslinked PPC with a gel fraction of 60.7% was prepared at 50 kGy irradiation dose, which showed a tensile strength at 20 °C of 45.5 MPa, whereas it was only 38.5 MPa for pure PPC. The onset degradation temperature (T_i) and glass transition temperature (T_g) of this crosslinked PPC was 246 °C and 45 °C, respectively, a significant increase related to pure PPC of 211 °C and 36 °C. Therefore, thermal and mechanical performances of PPC could be improved via electron-beam irradiation in the presence of suitable PFM.     

Synthesis and crystal structure of a new open-framework iron phosphate (NH4)4Fe3(OH)2F2[H3(PO4)4]: Novel linear trimer of corner-sharing Fe(III) octahedra

A new iron phosphate (NH₄)₄Fe₃(OH)₂F₂[H₃(PO₄)₄] has been synthesized hydrothermally at HF concentrations from 0.5 to 1.2 mL. Single-crystal X-ray diffraction analysis reveals its three-dimensional open-framework structure (monoclinic, space group P2₁/n (No. 14), a=6.2614(13) Å, b=9.844(2) Å, c=14.271(3) Å, β=92.11(1)°, V=879.0(3) Å³). This structure is built from isolated linear trimers of corner-sharing Fe(III) octahedra, which are linked by (PO₄) groups to form ten-membered-ring channels along [1 0 0]. This isolated, linear trimer of corner-sharing Fe(III) octahedra, [(FeO₄)₃(OH)₂F₂], is new and adds to the diverse linkages of Fe polyhedra as secondary building units in iron phosphates. The trivalent iron at octahedral sites for the title compound has been confirmed by synchrotron Fe K-edge XANES spectra and magnetic measurements. Magnetic measurements also show that this compound exhibit a strong antiferromagnetic exchange below T_N=17 K, consistent with superexchange interactions expected for the linear trimer of ferric octahedra with the Fe-F-Fe angle of 132.5°.     

Evaluation of 1-methyl-3,4-hydroxypyridinecarboxylic acids as possible bidentate chelating agents for iron(III): Metal–ligand solution chemistry

The chemical interactions of 1-methyl-3-hydroxy-4-pyridinecarboxylic acid (1M3H4P) and 1-methyl-4-hydroxy-3-pyridinecarboxylic acid (1M4H3P) with Fe(III) were investigated in aqueous 0.6 m (Na)Cl at 25 °C by means of potentiometric titrations and UV–Vis spectrophotometry. A large number of complexes were formed in solution with stoichiometry FeL_xH_y, x = 1, 2, 3 and y = 0, −1, −2. In view of a possible application to Fe(III) chelation therapy, the efficiencies of the ligands to chelate the metal ion were evaluated in vitro at physiological pH. 1M3H4P and 1M4H3P show a lower complexation efficiency with Fe(III) than that of other available chelators, but higher than that of their non-methylated analogs 3H4P and 4H3P.