Synthesis and characterization of Zn1−xNixFe2O4 spinels prepared by a citrate precursor

Nanocrystalline single-phase samples of Zn_1−xNi_xFe₂O₄ ferrites (0<x<1) have been obtained via a soft-chemistry method based on citrate-ethylene glycol precursors, at a relatively low temperature (650 °C). The influence of the nickel and zinc contents as well as that of heat treatments were investigated by means of X-ray powder diffraction, Brunauer-Emmett-Teller (BET) surface area, scanning electron microscopy (SEM) and Fourier Transform Infrared (FTIR) Spectroscopy. Higher Ni content increases the surface areas, the largest one (∼20 m²/g) being obtained for NiFe₂O₄ annealed at 650 °C for 15 h. For all compositions, the surface area decreases for prolonged annealing at 650 °C and for higher annealing temperatures. Those results were correlated to the particle size evolution; the smallest particles (∼50 nm) observed in the NiFe₂O₄ sample (650 °C, 15 h) steadily increase as Ni ions were replaced by Zn, reaching ∼100 nm in the ZnFe₂O₄ sample (650 °C, 15 h). For all the Zn_1−xNi_xFe₂O₄ samples and, whatever the heat treatments was, the FTIR spectra show two fundamental absorption bands in the range 650-400 cm⁻¹, characteristics of metal vibrations, without any superstructure stating for cation ordering. The highest ν₁-tetrahedral stretching, observed at ∼615 cm⁻¹ in NiFe₂O₄, shifts towards lower values with increasing Zn, whereas the ν₂-octahedral vibration, observed at 408 cm⁻¹ in NiFe₂O₄, moves towards higher wavenumbers, reaching 453 cm⁻¹ in ZnFe₂O₄.     

A structural study of the perovskite series Ca1−xNaxTi1−xTaxO3

Compounds in the solid solution series Ca_1−xNa_xTi_1−xTa_xO₃ were synthesized at 1300 °C, followed by annealing at 850 °C or 800 °C with quenching and/or slow cooling to room temperature. Rietveld refinement of their powder X-ray diffraction patterns show that all compounds are single-phase ternary perovskites which adopt the space group Pbnm (a≈b≈√2a_p; c≈2a_p; Z=4) at ambient conditions. The unit cell parameters and cell volumes of the compounds increase regularly with increasing values of x. The coordination of the A-site cations changes throughout the series from eight for CaTiO₃ to nine for NaTaO₃. Compounds with 0?x ?0.4 have A-site cations in eight fold coordination, whereas the coordination of those with 0.4<x<0.9 is ambiguous. Analysis of the crystal chemistry of the compounds shows that the change in coordination at x=0.4 is related to the departure of the B-site cations from the second coordination sphere of the A-site cations, as in compounds with x>0.4 the A-^IIO distances become less than the A-B intercation distances. Contemporaneous with these coordination changes, the tilt angles of the BO₆ polyhedra decrease with increasing values of x. This solid solution series is unusual in that these structural and coordination changes occur regardless that Goldschmidt tolerance factors remain essentially constant at approximately 0.89, and observed tolerance factors, assuming eight fold coordination of the A-site cations, range only from 0.91 to 0.93 (0?x?0.8).     

Synthesis and electrical conductivity of perovskite-type PrCo1−xMgxO3

Oxides in the system PrCo_1−xMg_xO₃ (x=0.0, 0.05, 0.10, 0.15, 0.20, 0.25) were synthesized by citrate technique and characterized by powder X-ray diffraction and scanning electron microscope. All compounds have a cubic perovskite structure (space group ). The maximum ratio of doped Mg in the system PrCo_1−xMg_xO₃ is x=0.2. Further doping leads to the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃. The substitution of Mg for Co improves the performance of PrCoO₃ as compared to the electrical conductivity measured by a four-probe electrical conductivity analyzer in the temperature range from 298 to 1073 K. The substitution of Mg for Co on the B site may be compensated by the formations of Co⁴⁺ and oxygen vacancies. The electrical conductivity of PrCo_1−xMg_xO₃ oxides increases with increasing x in the range of 0.0-0.2. The increase in conductivity becomes considerable at the temperatures ?673 K especially for x?0.1; it reaches a maximum at x=0.2 and 1073 K. From x>0.2 the conductivity of PrCo_1−xMg_xO₃ starts getting lower. This is probably a result of the segregation of Pr₆O₁₁ in PrCo_1−xMg_xO₃ , which blocks oxygen transport, and association of oxygen vacancies. A change in activation energy for all PrCo_1−xMg_xO₃ compounds (x=0-0.25) was observed, with a higher activation energy above 573 K and a lower activation energy below 573 K. The reasons for such a change are probably due to the change of dominant charge carriers from Co⁴⁺ to Vö in PrCo_1−xMg_xO₃ oxides and a phase transition mainly starting at 573 K.     

Structure and phase composition of nanocrystalline Ce1−xLuxO2−y

The microstructure and phase stability of nanocrystalline mixed oxide Lu_xCe_1−xO_2−y (x=0-1) are described. Nano-sized (3-4 nm) oxide particles were prepared by the reverse microemulsion method. Morphological and structural changes upon heat treatment in an oxidizing atmosphere were studied by transmission electron microscopy (TEM), X-ray diffraction (XRD), Raman and Yb³⁺ emission spectroscopy, the latter ion being present as an impurity in the Lu₂O₃ starting material. Up to 950 °C, the samples were single phase, with structure changing smoothly with Lu content from fluorite type (F) to bixbyite type (C). For the samples heated at 1100 °C phase separation into coexisting F- and C-type structures was observed for 0.35<x<0.7. It was also found that addition of Lu strongly hinders the crystallite growth of ceria during heat treatment at 800 and 950 °C.     

Crystal structure and electrical conductivity of lanthanum-calcium chromites-titanates La1−xCaxCr1−yTiyO3−δ (x=0-1, y=0-1)

Five series of perovskite-type compounds in the system La_1−xCa_xCr_1−yTi_yO₃ with the nominal compositions y=0, x=0-0.5; y=0.2, x=0.2-0.8; y=0.5, x=0.5-1.0; y=0.8, x=0.6-1.0 and y=1, x=0.8-1 were synthesized by a ceramic technique in air (final heating 1350 °C). On the basis of the X-ray analysis of the samples with (Ca/Ti)?1, the phase diagram of the CaTiO₃-LaCr^IIIO₃-CaCr^IVO₃ quasi-ternary system was constructed. Extended solid solution with a wide homogeneity range is formed in the quasi-ternary system CaCr^IVO₃-CaTiO₃-LaCr^IIIO₃. The solid solution La_{(1−x′−y)}Ca_(x′+y)Cr^IV_x′Cr^III_{(1−x′−y)}Ti_yO₃ exists by up to 0.6-0.7 mol fractions of CaCr^IVO₃ (x^′<0.6-0.7) at the experimental conditions. The crystal structure of the compounds is orthorhombic in the space group Pbnm at room temperature. The lattice parameters and the average interatomic distances of the samples within the solid solution ranges decrease uniformly with increasing Ca content. Outside the quasi-ternary system, the nominal compositions La_0.1Ca_0.9TiO₃, La_0.2Ca_0.8TiO₃, La_0.4Ca_0.6Cr_0.2Ti_0.8O₃ and La_0.3Ca_0.7Cr_0.2Ti_0.8O₃ in the system La_1−xCa_xCr_1−yTi_yO₃ were found as single phases with an orthorhombic structure. In the temperature range between 850 and 1000 °C, the synthesized single-phase compositions are stable at pO₂=6×10⁻¹⁶-0.21×10⁵ Pa. Oxygen stoichiometry and electrical conductivity of the separate compounds were investigated as functions of temperature and oxygen partial pressure. The chemical stability of these oxides with respect to oxygen release during thermal dissociation decreases with increasing Ca-content. At 900 °C and oxygen partial pressure 1×10⁻¹⁵-0.21×10⁵ Pa, the compounds with x>y (acceptor doped) are p-type semiconductors and those with x<y (donor doped) and x=y are n-type semiconductors. The type and level of electrical conductivity are functions of the concentration ratios of cations occupying the B-sites of the perovskite structures: [Cr³⁺]/[Cr⁴⁺] and [Ti⁴⁺]/[Ti³⁺]. The maximum electrical conductivity at 900 °C and pO₂=10⁻¹⁵ Pa was found for the composition La_0.1Ca_0.9TiO₃ (near 50 S/cm) and in air at 900 °C for La_0.5Ca_0.5CrO₃ (close to 100 S/cm).     

Mixed conductivity and Mössbauer spectra of (La0.5Sr0.5)1−xFe1−yAlyO3−δ (x=0-0.05, y=0-0.30)

Aluminum incorporation in the rhombohedrally distorted perovskite lattice of (La_0.5Sr_0.5)_1−xFe_1−yAl_yO_3−δ (x=0-0.05, y=0-0.30) decreases the unit cell volume and partial ionic and p-type electronic conductivities, while the oxygen nonstoichiometry and thermal expansion at 900-1200 K increase on doping. The creation of A-site cation vacancies has an opposite effect on the transport properties of Al-substituted ceramics. The maximum A-site deficiency tolerated by the (La,Sr)(Fe,Al)O_3−δ structure is however limited, close to 3-4%. The Mössbauer spectroscopy revealed progressive localization of electron holes and a mixed charge-compensation mechanism, which results in higher average oxidation state of iron when Al³⁺ concentration increases. The average thermal expansion coefficients of (La_0.5Sr_0.5)_1−xFe_1−yAl_yO_3−δ are (12.2-13.0)×10⁻⁶ K⁻¹ at 300-900 K and (20.1-30.0)×10⁻⁶ K⁻¹ at 900-1200 K in air. The steady-state oxygen permeability (OP) of dense Al-containing membranes is determined mainly by the bulk ionic conductivity. The ion transference numbers at 973-1223 K in air, calculated from the oxygen permeation and faradaic efficiency (FE) data, vary in the range 1×10⁻⁴-3×10⁻³, increasing with temperature.     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Synthesis and characterization of NixMg1−xAl2O4 nano ceramic pigments via a combustion route

MgAl₂O₄ was successfully used as a crystalline host network for the synthesis of nickel-based nano cyan refractory ceramic pigments. Different compositions of Ni_xMg_1−xAl₂O₄ (0.1 ? x ? 0.8) powders have been prepared by using a low temperature combustion reaction (LTCR) of the corresponding metal nitrates with urea (U) as a fuel at 300 °C in an open air furnace. The as-synthesized samples were characterized by thermal analysis (TG-DTG/DTA), X-ray powder diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). UV-Vis and diffuse reflectance spectroscopy (DRS) using CIE- L^∗a^∗b^∗ parameters methods have been used for color measurements. The results show that the Ni_xMg_1−xAl₂O₄ samples are the crystalline phase with a particle size of 8.85-43.66 nm in the temperature range 500-1200 °C. The density, particle size, shape and color are determined for all the prepared samples with different calcination times and temperatures.     

Neutron diffraction and magnetic study of the Nd0.7Pb0.3Mn1−xFexO3 (0?x?0.1) perovskites

The effect of Fe doping on the ferromagnetic Nd_0.7Pb_0.3Mn_1−xFe_xO₃ (x=0, 0.025, 0.05, 0.075, 0.1) phases has been studied in order to analyze the double-exchange interaction. The structural and magnetic study has been carried out by neutron powder diffraction and susceptibility measurements between 1.7 and 300 K. The substitution of Fe at the Mn site results in reductions in both the Curie temperature T_c and the magnetic moment per Mn ion without appreciable differences in the crystal structures. All the compounds crystallize in Pnma space group. The thermal evolution of the lattice parameters of the Nd_0.7Pb_0.3Mn_1−xFe_xO₃ (x=0.025, 0.05, 0.075) compounds shows discontinuities in volume and lattice parameters close to the magnetic transition temperature. Increasing amounts of Fe³⁺ reduces the double exchange interactions and no magnetic contribution for x=0.1 is observed. The magnetic structures of Nd_0.7Pb_0.3Mn_1−xFe_xO₃ (x=0, 0.025, 0.05, 0.075) compounds show that the Nd and Mn ions are ferromagnetically ordered.     

Surface properties and performance for VOCs combustion of LaFe1−yNiyO3 perovskite oxides

LaFeO₃, LaNiO₃ and substituted LaFe_1−yNi_yO₃ (y=0.1, 0.2 and 0.3) perovskites were synthesized by the citrate method and used in the catalytic combustion of ethanol and acetyl acetate. Chemical composition was determined by atomic absorption spectrometry (AAS) and specific areas from nitrogen adsorption isotherms. Structural details and surface properties were evaluated by temperature-programmed reduction (TPR), infrared spectroscopy (FTIR), X-ray diffraction analysis (XRD), temperature-programmed desorption of oxygen (O₂-TPD) and photoelectron spectroscopy (XPS). Characterization data revealed that total insertion of nickel in the LaFeO₃ takes place for substitution y=0.1. However, NiO segregation occurs to some extent, specifically at higher substitutions (y>0.1). The catalytic performance of these perovskites was evaluated in the combustion of acetyl acetate and ethanol. Among these molecules, ethanol exhibited the lowest ignition temperature, and the catalytic activity expressed as intrinsic activity (mol m⁻² h⁻¹) was found to increase substantially with the nickel substitution. These results can be explained in terms of the cooperative effect of a LaFe_1−yNi_yO₃ and NiO phases, whose relative concentration determines the oxygen activation capability and hence their reactivity.     

Enhancement of magnetic ordering temperature in iron substituted ytterbium manganate (YbMn1−xFexO3)

Oxides of the type YbMn_1−xFe_xO₃; x≤0.3 showing multiferroic behavior have been synthesized by the solid state route. These oxides crystallize in the hexagonal structure known for the parent YbMnO₃ with the c/a ratio increasing with Fe substitution. The distortion of the MnO₅ polyhedra (tbp) decreases and the Mn-O-Mn bonds in the a-b plane become shorter with Fe-substitution. Magnetic ordering is observed from the low temperature neutron diffraction study. The compounds were found to be antiferromagnetic and the ordering temperature T_N increased from 82 K for pure YbMnO₃ to 95 K for YbMn_0.7Fe_0.3O₃. Variable temperature dielectric measurements (15-110 K) show an anomaly in the dielectric constant at temperatures close to the antiferromagnetic ordering temperature for all the compositions, showing a unique correlation between the magnetic and electric field. The increase in the ordering temperature in YbMn_1−xFe_xO₃ is explained on the basis of increase in covalence of Mn/Fe-O-Mn/Fe bonds (shorter) with iron substitution.     

Synthesis, structure, and magnetic properties of SrMn1−xGaxO3−δ (x=0-0.5) perovskites

We report the synthesis of SrMn_1−xGa_xO_3−δ perovskite compounds and describe the dependence of their phase stability and structural and physical properties over extended cation and oxygen composition ranges. Using special synthesis techniques derived from thermogravimetric measurements, we have extended the solubility limit of random substitution of Ga³⁺ for Mn in the cubic perovskite phase to x=0.5. In the cubic perovskite phase the maximum oxygen content is close to 3−x/2, which corresponds to 100% Mn⁴⁺. Maximally oxygenated solid solution compounds are found to order antiferromagnetically for x=0-0.4, with the transition temperature linearly decreasing as Ga content increases. Increasing the Ga content introduces frustration into the magnetic system and a spin-glass state is observed for SrMn_0.5Ga_0.5O_2.67(3) below 12 K. These properties are markedly different from the long-range antiferromagnetic order below 180 K observed for the layer-ordered compound Sr₂MnGaO_5.50 with nominally identical chemical composition.     

Structural and physical properties evolution of BaIr1−xMnxO3 solid solutions synthesized by high-pressure sintering

The BaIr_1−xMn_xO₃ (0.0≤x≤1.0) solid solutions were synthesized by using the solid-state chemical method and high pressure sintering in the pressure range 0-5 GPa. According to the pressure-composition “phase diagram” at 1000 °C, the 9M BaIr_1−xMn_xO₃ transforms to the 6M form at 5 GPa and x≤1/6. In the x range 0.5-1.0, it transforms to the 9R form in a large pressure range. For the 9M BaIrO₃, the Mn ions substitution for Ir ions enhances the semiconducting property, and reduces the weak ferromagnetism. When x is larger than 1/3, the 9M/9R BaIr_1−xMn_xO₃ behave spin-glass-like state at low temperature, with the glass transition temperature T_g about 60 K. For the 6M BaIrO₃, the Mn ions doping results in that it transforms to insulator and spin-glass-like magnetism from the initial paramagnetic metal.     

Structural and conductivity studies of Y10−xLaxW2O21

The aim of this work was to determine structural parameters of the Y_10−xLa_xW₂O₂₁ (x=0-10) solid solution series and investigate their electric properties. Crystallographic data shows a gradual increase in symmetry with increasing La content, as the structure evolves from orthorhombic, Y₁₀W₂O₂₁, towards the pseudo-cubic structure of Y₅La₅W₂O₂₁. The solubility limit of La₂O₃ was found to be 50% (x=5). Above this level two phases were observed, La₆W₂O₁₅ and (La,Y)_10+xW_2−xO_21−δ. The conductivity of Y rich samples was very low, with σ of the order 2×10⁻⁵-5×10⁻⁵ S cm⁻¹ at 1000 °C, whilst ionic conductivity was observed for most La rich doped samples. The highest conductivity was observed for La₁₀W₂O₂₁ and its doped analogues, at 1×10⁻³-5×10⁻³ S cm⁻¹ at 1000 °C. Unit cell parameters were determined as a function of temperature from 0 to 1000°C, and thermal expansion of these materials was determined from temperature studies carried out at the Australian Synchrotron facility in Melbourne, Victoria, Australia.     

Enzyme mimics of spinel-type CoxNi1−xFe2O4 magnetic nanomaterial for eletroctrocatalytic oxidation of hydrogen peroxide

A series of spinel-type Co_xNi_1−xFe₂O₄ (x = 0, 0.2, 0.4, 0.5, 0.6, 0.8, 1.0) magnetic nanomaterials were solvothermally synthesized as enzyme mimics for the eletroctrocatalytic oxidation of H₂O₂. X-ray diffraction and scanning electron microscope were employed to characterize the composition, structure and morphology of the material. The electrochemical properties of spinel-type Co_xNi_1−xFe₂O₄ with different (Co/Ni) molar ratio toward H₂O₂ oxidation were investigated, and the results demonstrated that Co_0.5Ni_0.5Fe₂O₄ modified carbon paste electrode (Co_0.5Ni_0.5Fe₂O₄/CPE) possessed the best electrocatalytic activity for H₂O₂ oxidation. Under optimum conditions, the calibration curve for H₂O₂ determination on Co_0.5Ni_0.5Fe₂O₄/CPE was linear in a wide range of 1.0 × 10⁻⁸–1.0 × 10⁻³ M with low detection limit of 3.0 × 10⁻⁹ M (S/N = 3). The proposed Co_0.5Ni_0.5Fe₂O₄/CPE was also applied to the determination of H₂O₂ in commercial toothpastes with satisfactory results, indicating that Co_xNi_1−xFe₂O₄ is a promising hydrogen peroxidase mimics for the detection of H₂O₂.     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

Lattice crossover and mixed valency in the LaCo1−xRhxO3 solid solution

The full LaCo_1−xRh_xO₃ solid solution was investigated utilizing structural, electrical transport, magnetic, and thermal conductivity characterization. Strong evidence for at least some conversion of Rh³⁺/Co³⁺ to Rh⁴⁺/Co²⁺ is found in both structural and electrical transport data. The crystal structure is that of a rhombohedrally distorted perovskite over the range 0.0≤x≤0.1. The common orthorhombic distortion of the perovskite structure is found over the range 0.2≤x≤1.0. A crossover of all three orthorhombic cell edges occurs at x=0.5 giving the appearance of a cubic structure, which actually remains orthorhombic. The octahedra in the orthorhombic structure must be distorted for x values less than 0.5, and the observed distortion suggests orbital ordering for Co²⁺. Electrical resistivity measurements as a function of temperature show semiconducting-like regions for all compositions. There is a steady increase in electrical resistivity as the Rh content increases. Large positive thermopower values are generally obtained above 475 K. With increasing Rh substitution there is a decrease in thermal conductivity, which slowly rises with increasing temperature due to increased electrical conductivity. The electronic part of the thermal conductivity is suppressed significantly upon Rh substitution. A thermoelectric figure-of-merit (ZT) of about 0.075 has been achieved for LaCo_0.5Rh_0.5O₃ at 775 K, and is expected to reach 0.15 at 1000 K.     

Thermoelectric properties of polycrystalline La1−xSrxCoO3

Thermoelectric properties of polycrystalline La_1−xSr_xCoO₃, where Sr²⁺ is substituted in La³⁺ site in perovskite-type LaCoO₃, have been investigated. Sr-doping increases the electrical conductivity (σ) of La_1−xSr_xCoO₃, and also decreases the Seebeck coefficient (S) for 0.01?x?0.40. A Hall coefficient measurement reveals that the increase in electrical conductivity arises from increases in both carrier concentration and the Hall mobility. The decrease in the Seebeck coefficient is caused by a decrease in carrier effective mass as well as increase in carrier concentration. The highest power factor (σS²) is 3.7×10⁻⁴ W m⁻¹ K⁻² at 250 K for x=0.10. The thermal conductivity (κ) is about 2 W m⁻¹ K⁻¹ at 300 K for 0?x?0.04, and increases for x?0.05 because of an increase in heat transport by conductive carrier. The thermoelectric properties of La_1−xSr_xCoO₃ are improved by Sr-doping, and the figure of merit (Z=σS² κ⁻¹) reaches 1.6×10⁻⁴ K⁻¹ for x=0.06 at 300 K (ZT=0.048). For heavily Sr-doped samples, the thermoelectric properties diminish mainly because of the decrease in the Seebeck coefficient and the increase in thermal conductivity.     

Structural and magnetic properties of Pr18Li8Fe5−xMxO39 (M=Ru, Mn, Co)

A polycrystalline sample of Pr₁₈Li₈Fe₄RuO₃₉ has been synthesized by a solid state method and characterized by neutron powder diffraction, magnetometry and Mössbauer spectroscopy; samples of Pr₁₈Li₈Fe_5−xMn_xO₃₉ and Pr₁₈Li₈Fe_5−xCo_xO₃₉ (x=1, 2) have been studied by magnetometry. All these compounds adopt a cubic structure (space group , a₀∼11.97 Å) based on intersecting 〈111〉 chains made up of alternating octahedral and trigonal-prismatic coordination sites. These chains occupy channels within a Pr-O framework. The trigonal-prismatic site in Pr₁₈Li₈Fe₄RuO₃₉ is occupied by Li⁺ and high-spin Fe³⁺. The remaining transition-metal cations occupy the two crystallographically-distinct octahedral sites in a disordered manner. All five compositions adopt a spin-glass-like state at 7 K (Pr₁₈Li₈Fe₄RuO₃₉) or below.     

Study on the solid solution of YMn1−xFexO3: Structural, magnetic and dielectric properties

The solid solution of YMn_1−xFe_xO₃ (x=0.0, 0.1, 0.2, 0.3, 0.5, 1.0) was synthesized from the citrate precursor route. The hexagonal crystal structure related to YMnO₃ was stable for x?0.3. Rietveld refinement was carried out on the composition for x=0.3 and was refined to a major hexagonal phase (∼97%) with 3% of orthorhombic Y(Fe/Mn)O₃ phase. The a-axis lattice constant increases and the c-axis lattice constant decreases with x for x?0.2. The increase in the c-axis lattice constant at x=0.3 could be due to the doping of significant amount of d⁵ ion (high spin Fe³⁺ ion) in a trigonal bipyramidal crystal field. The detailed structural, magnetic and dielectric properties are discussed.