Hybrid passive/active absorbers for flow ducts

A new type of acoustic liner developed for broadband noise reduction in flow ducts is considered in this paper. It combines passive absorbent properties of a porous layer and active control at its rear face. The complete design procedure of this hybrid passive/active liner is developed here. The passive part is first considered with the determination of a suitable porous material and the cut-off frequency separating the active low frequency regime from the passive high frequency one. The control system is then presented: a digital adaptive feedback control is performed independently cell by cell, allowing an easy subsequent increase of the liner surface. The entire optimization process has been successfully applied to a laboratory flow duct: both predictions and measurements show the interest of the hybrid liner to reduce the noise radiation.     

A characterization of the scattered acoustic intensity field in the resonance region for simple spheres

The properties of the scattered acoustic vector fields generated by simple spheres illuminated by monotonic continuous wave (CW) plane waves are investigated. Analytical solutions are derived from general acoustic pressure scattering models and analyzed for wave numbers in the resonance region. Of particular interest is the understanding of the characteristics of the scattered acoustic vector field in the near-to-far-field transition region. The separable active and reactive components of the acoustic intensity are used to investigate the structural features of the scattered field components. Numerical results are presented for the near and transition regions for a rigid sphere. A method of mapping nulls in the scattered intensity field components is described. The analysis is then extended to include a simple fluid-filled boundary and finally the evacuated thin-walled shell. Near field acoustic intensity field structures are compared against mechanical material properties of vacuous shells. The ability to extract scattered field features is illustrated with measurements obtained from a recent in-air experiment using an anechoic chamber and acoustic vector sensor probes to measure the scattered acoustic vector field from rigid spheres.     

Electroacoustic absorbers: bridging the gap between shunt loudspeakers and active sound absorption

The acoustic impedance at the diaphragm of an electroacoustic transducer can be varied using a range of basic electrical control strategies, amongst which are electrical shunt circuits. These passive shunt techniques are compared to active acoustic feedback techniques for controlling the acoustic impedance of an electroacoustic transducer. The formulation of feedback-based acoustic impedance control reveals formal analogies with shunt strategies, and highlights an original method for synthesizing electric networks ("shunts") with positive or negative components, bridging the gap between passive and active acoustic impedance control. This paper describes the theory unifying all these passive and active acoustic impedance control strategies, introducing the concept of electroacoustic absorbers. The equivalence between shunts and active control is first formalized through the introduction of a one-degree-of-freedom acoustic resonator accounting for both electric shunts and acoustic feedbacks. Conversely, electric networks mimicking the performances of active feedback techniques are introduced, identifying shunts with active impedance control. Simulated acoustic performances are presented, with an emphasis on formal analogies between the different control techniques. Examples of electric shunts are proposed for active sound absorption. Experimental assessments are then presented, and the paper concludes with a general discussion on the concept and potential improvements.     

厚度模压电超声换能器无源声学材料研究进展*

厚度模压电超声换能器作为超声波发射、接收以及电信号间转换的载体,是超声成像与检测系统的核心器件,一般由压电层、匹配层和背衬层3部分组成。超声换能器的性能一定程度上决定着整体超声设备的性能,影响了其在工业、医学、军事等领域的应用。该换能器的关键性能指标(带宽、灵敏度)除了受到压电层的影响,还与匹配层、背衬层等无源声学材料的设计密切相关。该文综述了近年来厚度模压电超声换能器无源声学材料(匹配层、背衬层和声透镜)的研究进展,提出了当前该类材料面临的难题和解决途径,并对其未来发展方向进行了展望。     

Elasticity and active force generation of cochlear outer hair cells.

The cochlear outer hair cell is described by a cylindrical membrane model, characterized by area and shear moduli for a passive elastic element and an active tension element dependent on the membrane potential. In passive experiments, these moduli are determined from the pressure-strain relations. The area modulus obtained is 0.07 N m-1, similar to a lipid bilayer and the shear modulus is 0.007 N m-1. These moduli combined with previous active experiments show that the active tension is nearly isotropic and is about 1.6 x 10(-2) N m-1 V-1, resulting in a 0.5 nN/mV force per cell. This implies that the receptor potential for acoustical stimulation produces an active force comparable to the acoustic force applied to the basilar membrane per outer hair cell. This finding supports the hypothesis that the outer hair cell acts as feedback motor in the fine tuning mechanism of the mammalian ear.     

An acoustic backscattering technique for the detection of transient cavitation produced by microsecond pulses of ultrasound

An acoustic backscattering technique for detecting transient cavitation produced by 10-microseconds-long pulses of 757-kHz ultrasound is described. The system employs 10-microseconds-long, 30-MHz center frequency tone bursts that scatter from cavitation microbubbles. Experiments were performed with suspensions of hydrophobic polystyrene spheres in ultraclean water. Transient cavitation threshold pressures measured with the active cavitation detector (ACD) were always less than or equal to those measured using a passive acoustic detection scheme. The measured cavitation thresholds decreased with increasing dissolved gas content and increasing suspended particle concentration. Results also show that ultrasonic irradiation of the polystyrene sphere suspensions by the ACD lowered the threshold pressure measured with the passive detector. A possible mechanism through which suspensions of hydrophobic particles might nucleate bubbles is presented.     

Mode-locked CW dye lasers

Mode-locking of CW dye lasers are described. Three different methods: active mode-locking by acoustic loss modulation, pumping with mode-locked pulses and passive mode-locking by a saturable absorber, all resulted in stable continuous trains of tunable mode-locked pulses of various duration. Best results were obtained using passive mode-locking by a saturable absorber. The pulse lengths for this case were measured by auto-correlation technique to be as short as 1.5 ps. Factors influencing the mode-locking and possible improvements are discussed.     

An indirect hybrid sound transmission loss controller

The control of sound transmission through panels is an important noise control problem in the aerospace, aeronautical, and automotive industries. The trend towards using lightweight composite materials that have lower sound insulation performance is a negative factor regarding low frequency transmission loss. Double-panel partitions with the gap filled with sound absorption materials are often employed to improve the sound insulation performance with reduced added weight penalty. However, in the low frequency range, the strong coupling between the panels through the air cavity and mechanical paths may greatly reduce the sound transmission performance, making it even lower than the performance of a single panel in some frequency ranges. In this work, an experimental investigation of a new kind of hybrid (active/passive) acoustic actuator is presented. The idea consists of replacing the acoustic absorption material by a hybrid actuator aiming at improving the transmission loss at low frequencies without altering the passive attenuation. A prototype of the system is tested in a plane wave acoustic tube setup. Different kinds of SISO feedforward control implementations were used to attenuate the sound power transmitted through the hybrid active–passive panel using an error microphone or a particle velocity sensor placed downstream with respect to the sample panel. Measurement results of the transmission loss with active and hybrid attenuation are presented and discussed.     

Influence of adaptive control on vortex-driven instabilities in a scaled model of solid propellant motors

Aeroacoustic instabilities occur in many applications of technological interest and have undesirable effects on the steady operation of the system. Passive and active means are sought to reduce the level of oscillation and eliminate the instability. In the case of segmented solid rocket motors, observations indicate that low-frequency oscillations are generated by a coupling between vortex shedding in shear regions established in the flow and the acoustic eigenmodes of the system. This process is investigated in this article on a model-scale configuration representing the geometry of the motor. An active control loop is exploited to obtain resonant and non-resonant conditions for the same operating point. Adaptive techniques are used to stabilize the flow and the experiment serves as a testbed for active control. It is shown that an adaptive system may be applied to essentially suppress the pressure oscillations. The instability mechanism is then studied by analyzing the flow field with particle image velocimetry. It is found that control noticeably modifies the mean flow structure. Detailed studies of the vortex pattern in the shedding region indicate that the concentrated vorticity and the corresponding circulation values remain in the same range but that vorticity is shed more randomly when the resonance is eliminated by the controller. This indicates that control is achieved by reducing the level of organization in the vortex pattern. Under resonant conditions the level of pressure fluctuations results from coherent interactions between vortices and the downstream nozzle. This process feeds energy in one of the acoustic modes of the system enhancing the pressure level. It is made less effective by the control loop.     

Modular system for studying tonal sound excitation in resonators with heat addition and mean flow

An educational experimental system has been developed for studying tonal sound generation in acoustic resonators. Tones are excited by either heat addition or vortex shedding in the presence of mean flow. The system construction is straightforward and inexpensive. Several test arrangements and experimental data are described in this paper. The experimental setups include a modified Rijke tube, a standing-wave thermoacoustic engine, a baffled tube with mean flow, and an acoustic energy harvester with a piezoelement. Simplified mathematical models for interpreting data are discussed, and references are provided to literature with more advanced analyses. The developed system can assist both graduate and undergraduate students in understanding acoustic instabilities via conducting and analyzing interesting experiments.     

Waves in an active medium guided by a reactive surface with reactance of gain modulation

The characteristics of surface waves (i) in a passive medium supported by a passive surface with reactance modulation and an active surface with the modulation of either the reactance or the negative resistance, and (ii) in an active medium supported by a passive surface with a reactance modulation are investigated with emphasis on the band regions. The periodic variation is sinusoidal and is in the propagation direction. For a passive medium terminated by a passive surface with a reactance modulation, there are stop bands in frequency for the surface waves and the structure of the first two stop bands is analyzed. For a passive medium terminated by an active surface and for an active medium terminated by a reactance-modulated passive surface, the characteristics of the absolute instabilities occurring in the first-order band are examined. The nature of the convective instability taking place in the second-order band for an active medium terminated by a reactance-modulated surface is discussed. Analytical expressions for the frequency shift of the second-order band are deduced. The Floquet theory is used to obtain the exact dispersion relation in the form of a continued fraction which is analyzed by singular expansions.     

机翼颤振的有源声控制

借助于己推导出的声激励下绕三维薄翼的非定常位势流的精确解，本文进一步分析了限于弱扰动的声激励消除颤振的机理，讨论了声源参数对颤振边界的影响，并通过声一涡耦合的理论计算，解释了原有的风洞实验。结果表明，对于不同位置的声源，声致气动载荷的无环量和有环量部分起着不同的作用，而且，在声控制颤振的过程中，系统的各种参数存在一定的关系，必须合理地选取最佳参数。本文的研究为声控制技术在气动领域中的实际应用提供了理论基础。     

One dimensional study of a module for active/passive control of both absorption and transmission

Hybrid active/passive absorbers have proven to be efficient over a large frequency range. The next step consists in building up a system which can exhibit good absorption and insulation properties. To simulate such hybrid cell, active and passive behaviors of an electroacoustic loudspeaker have been modelized by using a one-dimensional approach. The rear acoustic load at the back of the membrane has been taken into account to obtain a reliable model. The proposed model has been validated with measurements performed in a 7 cm diameter tube. Then, a hybrid cell composed of a porous plate and a small thickness loudspeaker has been designed and numerically tested. It is shown that, when driving the loudspeaker for total absorption, the transmission losses are suppressed at lower frequencies. To overcome this problem, a dual actuator cell is designed to deal with both absorption and transmission. Simulations shows that this solution can lead to good results. It is also shown that interaction of the loudspeakers can be significantly reduced by using directive sources, thus lowering supplying voltages and condition number of the matrix inversion required by the control process.     

Propagation of low-frequency waves in biological tissues and vessels

Elastic surface waves in biotissue are considered taking into account its structure, and dispersion dependences are presented. Effects of contact of vibroacoustic action on the soft tissue of a human’s arm are studied, and the biotissue activity manifests itself as a vibroreaction with different characteristic times. A thermodynamic approach to the construction of rheological relations of active mechanochemical media is described. Dispersion characteristics of acoustic processes in passive and active blood vessels are given.     

Simulation of plasticity in nanocrystalline silicon

Molecular dynamics investigation of plasticity in a model nanocrystalline silicon system demonstrates that inelastic deformation localizes in intergranular regions. The carriers of plasticity in these regions are atomic environments, which can be described as high-density liquid-like amorphous silicon. During fully developed flow, plasticity is confined to system-spanning intergranular zones of easy flow. As an active flow zone rotates out of the plane of maximum resolved shear stress during deformation to large strain, new zones of easy flow are formed. Compatibility of the microstructure is accommodated by processes such as grain rotation and formation of new grains. Nano-scale voids or cracks may form if stress concentrations emerge which cannot be relaxed by a mechanism that simultaneously preserves microstructural compatibility.     

Mathematical simulation of sound propagation in a flow channel with impedance walls

The paper considers the specifics of calculating tonal sound propagating in a flow channel with an installed sound-absorbing device. The calculation is performed on the basis of numerical integrating on linearized nonstationary Euler equations using a code developed by the authors based on the so-called discontinuous Galerkin method. Using the linear theory of small perturbations, the effect of the sound-absorbing lining of the channel walls is described with the modified value of acoustic impedance proposed by the authors, for which, under flow channel conditions, the traditional classification of the active and reactive types of lining in terms of the real and imaginary impedance values, respectively, remains valid. To stabilize the computation process, a generalized impedance boundary condition is proposed in which, in addition to the impedance value itself, some additional parameters are introduced characterizing certain fictitious properties of inertia and elasticity of the impedance surface.     

Demonstration of the invariance principle for active sonar

Active sonar systems can provide good target detection potential but are limited in shallow water environments by the high level of reverberation produced by the interaction between the acoustic signal and the ocean bottom. The nature of the reverberation is highly variable and depends critically on the ocean and seabed properties, which are typically poorly known. This has motivated interest in techniques that are invariant to the environment. In passive sonar, a scalar parameter termed the waveguide invariant, has been introduced to describe the slope of striations observed in lofargrams. In this work, an invariant for active sonar is introduced. This active invariant is shown to be present in the time-frequency structure observed in sonar data from the Malta Plateau, and the structure agrees with results produced from normal mode simulations. The application of this feature in active tracking algorithms is discussed.     

Passive noise control by enhancing aeroacoustic interference due to structural discontinuities in close proximity

In-duct devices are commonly installed in flow ducts for various flow management purposes. The structural construction of these devices indispensably creates disruption to smooth flow through duct passages so they exist as structural discontinuities in duct flow. The presence of these discontinuities provides additional possibility of noise generation. In real practice, in-duct devices do not exist alone in any duct system. Even though each in-duct device would generate its own noise, it might be possible that these devices could be properly arranged so as to strengthen the interference between individual noise; thus giving rise to an overall reduction of noise radiation in the in-duct far field. This concept of passive noise control is investigated by considering different configurations of two structural discontinuities of simple form (i.e., a cavity) in tandem in an unconfined flow and in opposing setting within a flow duct. It is known that noise generated by a cavity in unconfined domain (unconfined cavity) is strongly dependent on flow-resonant behavior within the cavity so the interference it produces is merely aeroacoustic. The objective of the present study is to verify the concept of passive noise reduction through enhancement of aeroacoustic interference due to two cavities by considering laminar flow only. A two-dimensional approach is adopted for the direct aeroacoustic calculations using a direct numerical simulation (DNS) technique. The position and geometries of the cavities and the Mach number are varied; the resultant aeroacoustic behavior and acoustic power are calculated. The numerical results are compared with a single cavity case to highlight the effect of introducing additional cavities to the aeroacoustic problem. Resonant flow oscillations occur when two unconfined cavities are very close and the associated acoustic field is very intense with no noise reduction possible. However, for duct aeroacoustics, it is found that a 7.9 db reduction of acoustic power in the downstream side of the duct or a total reduction of ∼6 db is possible with opposing cavities having an offset of half a cavity length. In addition, the reduction is shown to be free from lock-on with trapped modes of the ducts with cavities.     

Active cancellation of occlusion: an electronic vent for hearing aids and hearing protectors

The occlusion effect is commonly described as an unnatural and mostly annoying quality of the voice of a person wearing hearing aids or hearing protectors. As a result, it is often reported by hearing aid users as a deterrent to wearing hearing aids. This paper presents an investigation into active occlusion cancellation. Measured transducer responses combined with models of an active feedback scheme are first examined in order to predict the effectiveness of occlusion reduction. The simulations predict 18 dB of occlusion reduction in completely blocked ear canals. Simulations incorporating a 1 mm vent (providing passive occlusion reduction) predict a combined active and passive occlusion reduction of 20 dB. A prototype occlusion canceling system was constructed. Averaged across 12 listeners with normal hearing, it provided 15 dB of occlusion reduction. Ten of the subjects reported a more natural own voice quality and an appreciable increase in comfort with the cancellation active, and 11 out of the 12 preferred the active system over the passive system.