接枝改性多面体齐聚倍半硅氧烷对左旋聚乳酸结晶行为的影响

以二氯甲烷为溶剂,利用溶液共混法将三种多面体齐聚倍半硅氧烷(POSS)分别与左旋聚乳酸(PLLA)进行共混,制备了不同POSS含量的单氨基POSS[(POSS-NH2)/PLLA]、POSS接枝聚乙二醇[(POSSPEG)/PLLA]和POSS接枝聚乳酸[(POSS-g-PLLA)/PLLA]复合材料。利用差示扫描量热仪和偏光显微镜(POM)分别对复合材料的本体结晶行为、结晶形貌和生长速率进行了观察。结果表明,当加入不同质量分数的POSS-PEG时,PLLA的结晶能力均得到改善,而POSS-NH2和POSS-g-PLLA仅在质量分数较低(1(wt)%)时提高了PLLA的结晶能力,具有较高质量分数时会阻碍PLLA分子链段的运动,从而限制其结晶。利用POM观察球晶生长过程发现,POSS-PEG的加入提高了PLLA的球晶生长速率。     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对PLLA的结晶行为有较大的影响。本文利用差示扫描量热仪(DSC)和偏光显微镜(POM)对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了系统研究。结果表明随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易形保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

聚左旋乳酸/聚消旋乳酸共混物的结晶行为

非晶态聚消旋乳酸(PDLLA)对聚左旋乳酸(PLLA)的结晶行为有较大的影响。本文利用差示扫描量热仪和偏光显微镜对不同分子量PLLA、PDLLA按不同比例制得的共混物结晶进行了研究。结果表明,随PDLLA含量的增大PLLA冷结晶温度升高,且越接近熔融温度。PDLLA分子量较小时PLLA球晶特征被明显破坏,PDLLA分子量较大时PLLA更易保持球晶特征且易形成环带球晶形貌,这与结晶速率与非晶组分的扩散速率匹配程度有关。低分子量的PDLLA使PLLA的最大生长速率对应的温度出现在较低温度。     

改性羟基磷灰石/聚乳酸纳米复合材料的结晶行为

利用溶剂复合的方法制备了具有良好生物相容性的表面接枝聚(γ-苄基-L-谷氨酸)的改性羟基磷灰石/聚乳酸纳米复合材料, 并研究了其熔融与结晶行为. 结果表明, 聚乳酸的玻璃化转变温度为60.3 ℃, 而复合材料的玻璃化转变温度达到65.8 ℃, 不同样品在140 ℃等温结晶后, 改性羟基磷灰石/聚乳酸复合材料的球晶直径仅为聚乳酸(PLLA)球晶直径的16.7%~66.7%. 复合材料的熔点提高到184.4 ℃.     

聚β-羟基丁酸酯顺丁烯二酸酐接枝共聚物的研究

采用DSC、TGA、POM和WAXD等方法对聚 β 羟基丁酸酯 (PHB)及其接枝顺丁烯二酸酐共聚物 (PHB g MA)的结晶行为、热稳定性和生物降解特性进行了研究 .结果表明接枝产物的热稳定性明显优于PHB ,热分解温度提高了 2 0余度 ;结晶行为发生很大的变化 .结晶速率减小 ,结晶温度降低 ,冷结晶温度升高 ,球晶的织态结构也随着MA接枝量的变化发生明显变化 ,并且接枝MA促进了PHB的生物降解     

非等温结晶对PLLA的热行为和形貌的影响

将聚L-乳酸(PLLA)熔化非等温熔融结晶, 采用DSC、POM、SEM等技术研究了降温速率对PLLA的热行为和形貌的影响. PLLA在低降温速率(2 ℃·min-1)下的结晶在118 ℃伴随有结晶机制的转变. 玻璃化温度和结晶度随着降温速率的降低而增大. 随着降温速率的降低, 球晶尺寸增大, 当降温速率为10 ℃·min-1 时, PLLA 为无定型材料. 采用模压成型的方法并控制降温速率制备了具有球晶结构的条状PLLA 生物材料, 与高降温速率下制备的PLLA相比,低降温速率下获得的具有球晶结构的PLLA材料的断面更光滑和致密, 但脆性增强.     

非晶高聚物对聚(ε-己内酯)在其与苯乙烯-丙烯腈共聚物相容共混物中球晶生长速率的影响

 本文研究了聚(ε-己内酯)(PCL)在其与苯乙烯-丙烯腈共聚物(SAN)的相容共混物中球晶生长速率与共混组成和结晶温度的关系.发现聚己内酯的球晶生长速率随着SAN的含量增加而下降.由于PCL与SAN是相容共混物,因此在用二次成核动力学方程描述PCL球晶生长速率时,我们引进了相互作用参数X.结果由共混体系的结晶动力学方程计算到的X值与由平衡熔点下降方法计算到的X₂₃值是相同的;而PCL晶体的折叠表面自由能则随着SAN含量的增加而下降.这些结果说明非晶高聚物SAN有碍于PCL球晶的生长.     

左旋聚乳酸的结晶行为研究

用DSC, WAXD和POM对Zn催化剂制备的左旋聚乳酸(PLLA)的熔体结晶行为进行了研究. 在95~125 ℃范围内, PLLA熔体结晶生成厚度约(14±1) nm的片晶, 该片晶不易发生熔体等温增厚. 对实验数据分别用Avrami方程和Arrhenius方程进行了计算, Avrami指数n=3±0.3, 表明PLLA以球晶形式生长, 其最大结晶速率温度为(105.0±0.5) ℃, t1/2约为5.2 min. 利用Lauritzen-Hoffmann（LH）理论对PLLA结晶机理进行了分析, 发现PLLA结晶的Regime Ⅱ和Regime Ⅲ的转变温度为107 ℃. Kg(Ⅱ)和Kg(Ⅲ)分别为4.57×105 K2和1.115×106 K2, 且Kg(Ⅲ)/Kg(Ⅱ)=2.4, 与LH理论值一致.     

聚左旋乳酸-聚乙二醇二嵌段共聚物的非等温结晶行为研究

通过变温广角X射线衍射(WAXD)、 差示扫描量热法(DSC)和偏光显微镜(POM)研究了聚左旋乳酸-聚乙二醇(PLLA-PEG)二嵌段共聚物的非等温结晶行为, 并用Ozawa方程分析了PLLA-PEG的非等温结晶动力学. 实验结果表明, 高熔点的硬段PLLA结晶符合Ozawa理论, 而低熔点的软段PEG对PLLA的结晶起到了稀释剂的作用; 当软段PEG开始结晶时, 已经结晶完全的硬段PLLA限制了PEG的结晶, 使得软段PEG的结晶不符合Ozawa理论. 此外, 不同降温速率下的结晶形貌研究结果表明, 随着降温速率的增加, 晶体经历了从环带球晶、 环带和十字消光的混合球晶到典型的十字消光球晶的转变, 并且球晶的尺寸也明显变小.     

高氯酸锂对PEO结晶结构和结晶行为的影响

利用配备热台的偏光显微镜(POM)、红外光谱仪(FTIR)和示差扫描量热器(DSC)等实验方法研究了高氯酸锂(LiClO4)与聚氧化乙烯(PEO)之间的络合作用对PEO结晶行为和结晶形态的影响.DSC测试结果表明在LiClO4/PEO二元共混体系中,PEO的熔融温度、结晶温度随着锂盐含量的增加出现先增加后降低的现象;而结晶度则是先不变后降低.FTIR结果表明LiClO4影响聚合物结晶性能的原因是Li+能和PEO中的醚基的络合作用.POM观察结果发现LiClO4/PEO共混体系中存在聚合物的球晶,共混体系中聚合物的球晶生长速率都随着结晶温度的升高而下降,并且球晶生长速率还随着体系中随LiClO4含量的增加而减小.     

Isothermal crystallization kinetics and thermal behavior of poly(?-caprolactone)/multi-walled carbon nanotube composites

This study describes the preparation of poly(?-caprolactone) (PCL)/multi-walled carbon nanotube (MWCNT) composites by ultrasonically mixing the PCL and as-fabricated MWCNT in a tetrahydrofuran solution. The TEM images show that the MWCNT is well separated and uniformly distributed in the PCL matrix. Differential scanning calorimetry (DSC), thermogravimetric analyzer (TGA), X-ray diffraction (XRD) and polarized optical microscopy (POM) were used to investigate the isothermal crystallization kinetics, crystalline structure and thermal behavior of PCL and PCL/MWCNT nanocomposites. DSC isothermal results revealed that the activation energy of PCL extensively decreases with increasing MWCNT contents, suggesting that the loading of MWCNT into PCL matrix probably induced heterogeneous nucleation during crystallization processes. From TGA data, the addition of small amount of MWCNT into PCL matrix can improve the thermal stability of PCL matrix. TGA isothermal degradation data illustrate that the activation energy E_d of the composites is smaller than that of PCL. This phenomenon can be attributed to the incorporation of more MWCNT loading into PCL caused a decrease in the degradation rate and an increase in the residual weight for PCL/MWCNT nanocomposites.     

Surface‐modified hydroxyapatite linked by L‐lactic acid oligomer in the absence of catalyst

A new surface modification method of hydroxyapatite nanoparticles (n‐HA) by surface grafting reaction of L ‐lactic acid oligomer with carboxyl terminal (LAc oligomer) in the absence of any catalyst was developed. The LAc oligomer with a certain molecular weight was directly synthesized by condensation of L ‐lactic acid. Surface‐modified HA nanoparticles (p‐HA) were attested by Fourier transformation infrared spectroscopy, ³¹P MAS‐NMR, and thermal gravimetric analysis (TGA). The results showed that LAc oligomer could be grafted onto the n‐HA surface by forming a Ca carboxylate bond. The grafting amount of LAc oligomer was about 13.3 wt %. The p‐HA/PLLA composites showed good mechanical properties and uniform microstructure. The tensile strength and modulus of the p‐HA/PLLA composite containing 15 wt % of p‐HA were 68.7 MPa and 2.1 GPa, respectively, while those of the n‐HA/PLLA composites were 43 MPa and 1.6 GPa, respectively. The p‐HA/PLLA composites had better thermal stability than n‐HA/PLLA composites and neat PLLA had, as determined by isothermal TGA. The hydrolytic degradation behavior of the composites in phosphate buffered saline (PBS, pH 7.4) was investigated. The p‐HA/PLLA composites lost their mechanical properties more slowly than did n‐HA/PLLA composites in PBS because of their reinforced adhesion between the HA filler and PLLA matrix. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5177–5185, 2005     

Rheology and crystallization behavior of PLLA/TiO2‐g‐PDLA composites

Poly(L‐lactide) (PLLA) composites with TiO₂‐g‐poly(D‐lactide) (PDLA), which was synthesized by surface‐initiated opening ring polymerization with TiO₂ as initiator and Sn(Oct)₂ as catalyst, were prepared by solution casting. The synthesized TiO₂‐g‐PDLA was characterized by transmission electron microscope (TEM) and dynamic laser scattering (DLS), showing larger size corresponding to that of TiO₂. Fourier transform infrared spectroscopy (FT‐IR) and X‐ray photoelectron spectroscopy (XPS) measurements were further carried out and indicated that PDLA was grafted onto TiO₂ through covalent bond. For PLLA/TiO₂‐g‐PDLA composites, the stereocomplex crystallites were formed between PDLA grafted on the surface of TiO₂ and the PLLA matrix, which was determined by FT‐IR, differential scanning calorimetry (DSC), and X‐ray diffractometer (XRD). The influence of stereocomplex crystallites on the rheological behavior of PLLA/TiO₂‐g‐PDLA was investigated by rheometer, which showed greater improvement of rheological properties compared to that of PLLA/TiO₂ composites especially with a percolation content of TiO₂‐g‐PDLA between 3 wt%–5 wt%. The crystallization and melting behavior of PLLA/TiO₂‐g‐PDLA composites were studied by DSC under different thermal treatment conditions. The formed PLA stereocomplex network acted as nucleating agents and a special interphase on the functional surface of TiO₂, which resulted in imperfect PLLA crystal with lower melting temperature. When the thermal treatment was close to the melting temperature of PLA stereocomplex, the crystallinity approached to the maximum. The isothermal crystallization study by polarizing microscope (POM) indicated that stereocomplex network presented stronger nucleation capacity than TiO₂‐g‐PDLA. Copyright © 2015 John Wiley & Sons, Ltd.     

溶剂诱导的聚乳酸/聚乳酸衍生物共结晶行为

通过溶液浇铸法制备不同组分的左旋聚乳酸(PLLA)和聚(L-2-羟基-3-甲基丁酸)(PL-2H3MB)共混物.运用差示扫描量热仪(DSC)、偏光显微镜(POM)、广角X射线衍射(WAXD)和热重分析仪(TGA)分析共混物的结晶、熔融行为和热稳定性.通过观察到DSC加热曲线中新的熔融峰判断PLLA和PL-2H3MB共晶...     

Nanocomposites of poly(l-lactide) and surface-grafted TiO2 nanoparticles: Synthesis and characterization

A new method of surface modification of TiO₂ nanoparticles by surface-grafting l-lactic acid oligomer was developed. The surface-grafting reaction was evaluated by Fourier transformation infrared (FTIR) and thermal gravimetric analysis (TGA). The results showed that l-lactic acid oligomer could be easily grafted onto the TiO₂ nanoparticles surface in the presence of stannous octanoate and the highest amount of grafted polymer was about 8.5% in weight. Transmission electron microscopy (TEM) and scanning electron microscopy (SEM) results showed that grafted TiO₂ (g-TiO₂) in chloroform or PLLA matrix approximated to uniform, while unmodified TiO₂ nanoparticles tended to aggregate. The tensile strength of this material was greatly improved by the addition of g-TiO₂ nanoparticles in poly(l-lactide) (PLLA) matrix. The tensile strength of the g-TiO₂/PLLA nanocomposite containing 5 wt.% of g-TiO₂ was 72 MPa, which was 23.1% higher than that of pure PLLA. Even though the incorporation of the TiO₂ nanoparticles into PLLA led to the deterioration of its elongation at break, the g-TiO₂/PLLA nanocomposite also exhibited better ductility than that of TiO₂/PLLA nanocomposite.     

Preparation and properties of polycarbonate/polyhedral oligomeric silsesquioxanes (POSS) hybrid composites

Octaphenylsilsesquioxane (PH‐POSS) and octa(γ‐methacryloxypropyl)silsesquioxane (MA‐POSS) were successfully synthesized by hydrolytic condensation of phenyltrichlorosilane and γ‐methacryloxypropyltrimethoxysilane, and characterized by Fourier transform infrared (FT‐IR), ¹H and ²⁹Si nuclear magnetic resonance (NMR), and matrix‐assisted laser desorption/ionization‐time of flight (MALDI‐TOF) mass spectrum. Morphology, degradation behavior, thermal, and mechanical properties of hybrid composites were studied by transmission electron microscopy (TEM), polarized optical microscopy (POM), differential scanning calorimetry (DSC), thermogravimetric analysis (TGA), surface contact angle (SCA), tensile, and impact testing. Domains of PH‐POSS and MA‐POSS dispersed in the matrix with a wide size distribution in a range of 0.1–0.5 µm, while PH‐POSS exhibited a preferential dispersion. Because of the possible homopolymerization of MA‐POSS during the melt blending, the glass transition temperature of polycarbonate (PC)/MA‐POSS composites remained nearly unchanged with respect to PC/PH‐POSS composites that showed a depression of T_g due to the plasticization effect. It is interesting to note that the incorporation of POSS retarded the degradation rates of PC composites and thus significantly improved the thermal stabilities. Si? O fractions left during POSS degradations were a key factor governing the formation of a gel network layer on the exterior surface. This layer possessed more compact structures, higher thermal stabilities, and some thermal insulation. In addition, percentage residues at 700°C (C₇₀₀) significantly increased from 10.8% to 15.8–22.1% in air. Fracture stress of two composites showed a slight improvement, and the impact strength of them decreased monotonically with the increase of POSS loading. Copyright © 2011 John Wiley & Sons, Ltd.     

Poly(L‐lactide)/layered double hydroxides nanocomposites: Preparation and crystallization behavior

Novel nanocomposites from poly(L ‐lactide) (PLLA) and an organically modified layered double hydroxide (LDH) were prepared using the melt‐mixing technique. The structure and crystallization behavior of these nanocomposites were investigated by means of wide‐angle X‐ray diffraction (WAXD), transmission electron microscopy (TEM), Fourier transform infrared (FTIR) spectroscopy, differential scanning calorimetry (DSC), and polarized optical microscopy (POM). WAXD results indicate that the layer distance of dodecyl sulfate‐modified LDH (LDH‐DS) is increased in the PLLA/LDH composites, compared with the organically modified LDH. TEM analysis suggests that the most LDH‐DS layers disperse homogenously in the PLLA matrix in the nanometer scale with the intercalated or exfoliated structures. It was found that the incorporation of LDH‐DS has little or no discernable effect on the crystalline structure as well as the melting behavior of PLLA. However, the crystallization rate of PLLA increases with the addition of LDH‐DS. With the incorporation of 2.5 wt % LDH‐DS, the PLLA crystallization can be finished during the cooling process at 5 °C/min. With the addition of 5 wt % LDH‐DS, the half‐times of isothermal melt‐crystallization of PLLA at 100 and 120 °C reduce to 44.4% and 57.0% of those of the neat PLLA, respectively. POM observation shows that the nucleation density increases and the spherulite size of PLLA reduces distinctly with the presence of LDH‐DS. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2222–2233, 2008     

Isothermal crystallization behavior and unique banded spherulites of hydroxyapatite/poly(L-lactide) nanocomposites

<正>Hydroxyapatite/poly(L-lactide)(HA/PLLA) nanocomposites were prepared by the solvent mixing method.The isothermal crystallization behavior was studied by differential scanning calorimetry(DSC) and polarized optical microscopy (POM).The results show that the crystallization behavior of HA/PLLA composites was strongly affected by the content of HA and crystallization temperature,and the addition of HA could promote nucleation and enhance the crystallization rate. When isothermal crystallization was carried out at 110℃,the HA/PLLA nanocomposite with 1%HA content crystallized most rapidly among all the composites and the half crystallization time was only 1.0 min.Banded spherulites were observed for the HA/PLLA composites,but no banded spherulites were seen in the crystals of PLLA under the same condition.     

Thermal Properties of Poly(L-lactide)/Calcium Carbonate Nanocomposites

Summary: Thermal properties of nanocomposites prepared of poly(L-lactide) (PLLA) and CaCO₃ applying differential scanning (DSC) calorimetry and thermogravimetry (TG) were studied. Nanocomposites were prepared by extrusion process at 170 °C. DSC measurements show that CaCO₃ has no influence on glass transition and melting point of PLLA but lowers its cold crystallization temperature. There is no difference in glass transition temperature of PLLA before and after extrusion. High temperature thermal stability of the PLLA in the composites is poorer than neat PLLA. Kinetic parameters also indicate greater reactivity of the system upon CaCO₃ addition.     

Preparation,Tg improvement,and thermal stability enhancement mechanism of soluble poly(methyl methacrylate) nanocomposites by incorporating octavinyl polyhedral oligomeric silsesquioxanes

The soluble poly(methyl methacrylate‐co‐octavinyl‐polyhedral oligomeric silsesquioxane) (PMMA–POSS) hybrid nanocomposites with improved T_g and high thermal stability were synthesized by common free radical polymerization and characterized using FTIR, high‐resolution ¹H NMR, ²⁹Si NMR, GPC, DSC, and TGA. The POSS contents in the nanocomposites were determined based on FTIR spectrum, revealing that it can be effectively adjusted by varying the feed ratio of POSS in the hybrid composites. On the basis of the ¹H NMR analysis, the number of the reacted vinyl groups on each POSS molecules was determined to be about 6–8. The DSC and TGA measurements indicated that the hybrid nanocomposites had higher T_g and better thermal properties than the pure PMMA homopolymer. The T_g increase mechanism was investigated using FTIR, displaying that the dipole–dipole interaction between PMMA and POSS also plays very important role to the T_g improvement besides the molecular motion hindrance from the hybrid structure. The thermal stability enhances with increase of POSS content, which is mainly attributed to the incorporation of nanoscale inorganic POSS uniformly dispersed at molecular level. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5308–5317, 2007