Abnormal resistivity behavior of Cu–Ni and Cu–Co alloys in undercooled liquid state

The resistivity behavior of undercooled liquid Cu–Ni and Cu–Co alloys had been studied in the contactless method, to probe the structure transition in undercooled melts during the cooling process. Over the entire concentration range, linear behavior of resistivity with temperature was obtained in liquid and undercooled liquid Cu–Ni system. It implied that the formation of icosahedral order might not influence the electron scattering in undercooled liquid Cu–Ni alloys. Similar results were obtained in Cu–Co system in the vicinity of liquidus temperature. A turning point was obvious in temperature coefficient of resistivity for undercooled liquid Cu–Co alloys around the bimodal line, which was interpreted to be responsible for metastable liquid–liquid phase separation. During liquid phase separation process, resistivity decreased and the temperature coefficient of resistivity was larger than that of homogeneous melts. In combination with transmission electron microscopy and scanning electron microscope studies on the as-solidified microstructure, this was interpreted as the formation of egg-type structure and concentration change in Cu-rich and Co-rich phases. The mechanism controlling the separation and droplets motion was also discussed in undercooled liquid Cu–Co system.     

Structural asymmetry in liquid Fe–Si alloys

The thermodynamic properties and microscopic structure of liquid Fe–Si alloys at 1873 K were studied by using the regular associated solution model. The model was utilized to determine the complex concentration in a regular associated solution of Fe, Si and Fe₂Si. The complex concentration was then used to calculate the integral excess free energy of mixing, activity, concentration fluctuations in the long-wavelength limit, S_CC (0), and the Warren–Cowley short-range parameter α ₁. The analysis suggests that heterocoordination leading to the formation of complex Fe₂Si is likely to exist in the liquid and is of a strongly interacting nature. The theoretical analysis reveals that the alloy is more ordered towards the Fe-rich region. The observed asymmetry in the properties of mixing of Fe–Si alloys in the molten state is successfully explained on the basis of the regular associated solution model.     

Interdiffusion and thermotransport in Ni–Al liquid alloys

In this paper, we present extensive self-consistent results of molecular dynamics (MD) simulations of diffusion and thermotransport properties of Ni–Al liquid alloys. We develop a new formalism that allows easy connection between results of the MD simulations and the real experiments. In addition, this formalism can be extended to the case of ternary and higher component liquid alloys. We focus on the temperature and composition dependence of the self-diffusion coefficients, interdiffusion coefficients, thermodynamic factor, Manning factor and the reduced heat of transport. The two latter quantities both represent measures of the off-diagonal Onsager phenomenological coefficients. The Manning factor and the reduced heat of transport can be related to experimentally obtainable quantities provided the thermodynamic factor is available. The simulation results for the reduced heat of transport show that for all compositions, in the presence of a temperature gradient, Ni tends to migrate to the cold end. This is in agreement with an available experimental study for a Ni_21.5Al_78.5 melt (only qualitative result is available so far).     

Concentration dependence of thermodynamic,transport and surface properties in Ag–Cu liquid alloys

Thermodynamic, transport and surface properties of Ag–Cu liquid alloys have been investigated on the basis of a simple statistical model. The free energy of mixing, heat of mixing and entropy of mixing have been computed to understand the thermodynamic properties of Ag–Cu alloys in liquid state at 1,423 K. The concentration–concentration fluctuations in the long wavelength limit and the chemical short range order parameter have been determined to comprehend the microscopic and structural information of the alloy. The viscosity and surface tension of the alloy have been evaluated to analyze the transport and surface properties. The theoretical analysis reveals that the energy parameter is temperature dependent, and that Ag–Cu liquid alloy is a weakly interacting-phase separating system.     

Oxygen generation in anodized Ta–Cu alloys

Comparison is made of the influences of copper in the development of amorphous anodic films on Ta-Cu alloys, containing up to 57 at.%Cu, in ammonium pentaborate electrolyte at 293 K. The various films are based on tantala, with low concentrations of copper, relative to those of the alloys, since copper species migrate through the films more rapidly than Ta⁵⁺ ions and are lost to the electrolyte on reaching the film surface. Of particular interest, film growth on Ta-1.5at.% Cu alloy at 1, 0.1 and 0.01 mA cm^?2 proceeds with generation of oxygen, which is contained in nanoscale bubbles within the oxide. Bubbles are more numerous as the current density decreases. In the case of Ta-12at.% Cu and Ta-57at.%Cu alloys, the films are flawed extensively by more numerous oxygen bubbles, which are present mainly in the outer parts of the anodic films; oxygen production and film damage due to the bursting of bubbles limit the anodizing voltage to relatively low values. It is suggested that copper species modify the electron levels, and possibly structure, of the tantala-based films, thereby facilitating oxygen generation within the bulk film by oxidation of O^2- ions of the oxide.     

Origin of tweed in Au–Cu–Al alloys

The premartensitic tweed in Au–Cu–Al alloys, contrary to previous thought that resort to defects, is confirmed to be associated with the coherent embryos of an intermediate phase (I phase) embedded in parent phase. The parent?→?I phase transformation temperature was measured by differential scanning calorimeter and dynamic mechanical analysers, which shifts from 82.3 to 557.6?°C depending on the alloy composition. X-ray diffraction and transmission electron microscopes (TEM) results show that the parent?→?I phase transformation is a charge density wave transition that cannot be suppressed even by melt-spun method, which shows obvious compositional inhomogeneity between I phase and parent. The results imply that the parent?→?I phase transition is a fast displacive transformation coupled with diffusion. Moreover, accompanying the parent?→?I phase transformation, alloys demonstrate diversified microstructure revealed by TEM observation, from tweed to chessboard nanowires or twins. These findings provide the experimental evidence for that parent?→?I phase transformation in Au–Cu–Al alloys is originated from pseudospinodal decomposition as theoretically predicted.     

Determination of surface tension of liquid ternary Ni–Cu–Fe and sub-binary alloys

Experimental data in the literature are almost limited to determine the thermophysical properties of multicomponent complex alloys, especially due to the inability of laboratories to achieve the desired ideal conditions, due to the difficulty of protection from oxidation at high temperatures and other contamination at high temperatures, due to time and cost in laboratory studies. Due to these reasons, the theoretical data obtained in this subject is of great importance. In this study, a series of geometric and physical models, such as Chou’s general solution model (GSM), Muggianu’s Model, Kohler’s Model, Toop’s Model, Hillert’s Model, Guggenheim’s Model, Butler’s Model, Egry’s Model and ideal solution model for quasi-binary alloy system for Section A: Ni_{0.4(1 – x)}Cu_xFe_{0.6(1 – x)}. and Section B: (Ni_xCu_0.2Fe_{0.8 – x}) are used to calculate the surface tension-composition and surface tension-temperature curves of the Cu-Fe-Ni ternary liquid system are plotted. The data for this process is evaluated by means of an extended Redlich-Kister-Muggianu polynomial fit to the experimental values of the surface tensions of the binary liquid alloy systems. The obtained results for these models are also compared with the available data in the literature and relatively good agreements are observed. In addition, the surface segregation having important key factor in determining surface tension of the liquid alloy Ni-Fe-Cu has also been investigated in this work.     

63Cu NMR analysis of microstructure evolution in Al–Cu–Mg alloys

⁶³Cu NMR spectroscopy has been used to detect metastable Guinier–Preston–Bagaryatsky (GPB) zones and nanoscale precipitates of equilibrium S-phase (Al₂CuMg) in dilute alloys of aluminium containing copper and magnesium with compositions which lie in the α?+?S phase field. The GPB zones are observed to form rapidly at room temperature with a time development closely related to the Vickers hardness. The final development of S-phase in the alloy has been confirmed by the observation of a line shape in the alloy identical to that observed in a specimen prepared from stoichiometric Al₂CuMg. Analysis of the hyperfine structure of the ⁶³Cu line shape observed for S-phase shows clearly that two Cu sites are present with approximately equal population. This result suggests that possibly two crystallographically distinct Al₂CuMg phases are present. The addition of small amounts of silver to Al–Cu–Mg alloys in the α?+?θ phase field is known to induce the formation of Ω-phase: a slight distortion of tetragonal θ-phase Al₂Cu. A hyperfine-structured ⁶³Cu line shape assigned to Ω-phase, indicating one distinct Cu site, has been observed in two separate Al–1.7?at.%?Cu–0.33?at.%?Mg alloys containing 0.1 and 0.18?at.%?Ag, but not in the same Al–Cu–Mg alloy without Ag.     

Microstructural evolution in Al–Mn–Cu–(Be) alloys

This study investigates the effects of alloying elements on the microstructural evolution of Al-rich Al–Mn–Cu–(Be) alloys during solidification, and subsequent heating and annealing. The samples were characterised using scanning electron microscopy, energy dispersive X-ray spectroscopy, synchrotron X-ray diffraction, time-of-flight secondary-ion mass spectroscopy, and differential scanning calorimetry. In the ternary Al₉₄Mn₃Cu₃ (at%) alloy, the phases formed during slower cooling (≈1?K?s^?1) can be predicted by the known Al–Mn–Cu phase diagram. The addition of Be prevented the formation of Al₆Mn, decreased the fraction of τ₁-Al₂₉Mn₆Cu₄, and increased the fraction of Al₄Mn. During faster cooling (≈1000?K?s^?1), Al₄Mn predominantly formed in the ternary alloy, whereas, in the quaternary alloys, the icosahedral quasicrystalline phase dominated. Further heating and annealing of the alloys caused an increase in the volume fractions of τ₁ in all alloys and Be₄Al (Mn,Cu) in quaternary alloys, while fractions of all other intermetallic phases decreased. Solidification with a moderate cooling rate (≈1000?K?s^?1) caused considerable strengthening, which was reduced by annealing for up to 25% in the quaternary alloys, while hardness remained almost the same in the ternary alloy.     

Thermophysical properties of Cu–In–Sn liquid Pb-free alloys: viscosity and surface tension

The viscosity of a few Cu–In–Sn liquid alloys has been investigated by a number of geometric (Muggianu, Kohler, Toop) and physical thermodynamic models (Kozlov–Romanov–Petrov, Budai–Benko–Kaptay, Schick et al.) and GSM for the cross section (z/y = 1/3) in Pb-free liquid alloy Cu_x–In_y–Sn_z at 1073 K. Moreover, the surface tensions of the same liquid alloys have been investigated by a number of geometric models and the Butler model for the cross section Cu_x–In_y–Sn_z (z/(y + z) = 0, 0.1, 0.3, 0.5, 0.7, 0.9, 1) at the same temperature. The best agreement of the surface tensions was obtained in the Kohler model for x_Cu = 10 at % and the Butler model for x_Cu = 20 at % and x_Cu = 30 at.%, respectively. The best agreement among chosen geometric and physical models and experiment for these selected sections Cu₈₀In₁₅Sn₅, Cu₇₅In₁₅Sn₁₀, Cu₅₅In₇Sn₃₈, Cu₃₃In₅₀Sn₁₇ and Cu₂₆In₅₅Sn₁₉ at 1073 K was obtained for the Budai–Benkö–Kaptay model.     

Experimental and computer simulation determination of the structural changes occurring through the liquid–glass transition in Cu–Zr alloys

Molecular dynamics (MD) simulations were performed of the structural changes occurring through the liquid–glass transition in Cu–Zr alloys. The total scattering functions (TSF), and their associated primary diffuse scattering peak positions (K _p), heights (K _h) and full-widths at half maximum (K _FWHM) were used as metrics to compare the simulations to high-energy X-ray scattering data. The residuals of difference between the model and experimental TSFs are ～0.03 for the liquids and about 0.07 for the glasses. Over the compositional range studied, Zr_{1? x} Cu _x (0.1 ≤ x ≤ 0.9), K _p, K _h and K _FWHM show a strong dependence on composition and temperature. The simulation and experimental data correlate well between each other. MD simulation revealed that the Cu–Zr bonds undergo the largest changes during cooling of the liquid, whereas the Cu–Cu bonds change the least. Changes in the partial-pair correlations are more readily seen in the second and third shells. The Voronoi polyhedra (VP) in glasses are dominated by only a few select types that are compositionally dependent. The relative concentrations of the dominant VPs rapidly change in their relative proportion in the deeply undercooled liquid. The experimentally determined region of best glass formability, x _Cu ～ 65%, shows the largest temperature dependent changes for the deeply undercooled liquid in the MD simulation. This region also exhibits very strong temperature dependence for the diffusivity and the total energy of the system. These data point to a strong topological change in the best glass-forming alloys and a concurrent change in the VP chemistry in the deeply undercooled liquid.     

Electrical resistivity of liquid Bi–Sb alloys

The electrical resistivities of liquid Bi–Sb alloys have been measured by DC four-probe method within Bi-rich composition through a wide temperature range. The distinct anomaly of a hump shape was observed on resistivity–temperature (ρndash;T) curves for liquid Bi–Sb alloys on heating at the relatively high temperatures. These anomalies have revealed the temperature-induced liquid–liquid phase transition in Bi–Sb melts. The DSC results for BiSb20wt% alloy further prove the existence of liquid–liquid transition. Measuring the ρ–T curves first on heating and then on cooling we have found that on cooling the ρ–T curve remained linear. It means that the postulated liquid–liquid transition may be irreversible.     

Electrical resistivity of liquid Sb–Zn alloys

Using the DC four-probe method, temperature dependence of the electrical resistivity (ρ???T) of Sb_{100? x} Zn _x (x?=?25,?40,?50,?57,?61,?80 at%) alloys was investigated in the temperature range of 500–860°C. The results showed that resistivity of each liquid alloy decreased non-linearly with temperature increasing above their liquidus (T _L) until reaching critical temperature, at which the resistivity–temperature coefficients dρ/dT–T converts from negative into positive. The phenomena of liquid phase transformation might relate with the dissociation of covalent bonds, chemical orders and associations in Sb–Zn melts.     

Continuous transformation from quasicrystals to approximants in Al–Cu–Fe alloys

Continuous transformation of icosahedral quasicrystals as observed in Al-Cu-Fe alloys proceeds through intermediate modulated structures towards rational approximants with a rhombohedral structure. Corresponding to the diffuse scattering in the electron diffraction during the transformation, a tweed contrast emerges throughout the icosahedral phase matrix. High-resolution electron microscopy reveals a complex modulated structure which tends to evolve into rhombohedral microdomains. The observed distortion of the reciprocal quasilattice due to the structural modulation has been simulated on a computer by introducing linear phason strains into the quasicrystals.     

The effect of Cu on precipitation in Al–Mg–Si alloys

TEM investigations of two alloys isothermally heat treated at 175°C and 260°C show how Cu additions to the Al–Mg–Si system affect precipitation. Both alloys had a solute content Mg?+?Si?=?1.3 at.%, 0.127 at.% Cu, but with Mg/Si 0.8 and 1.25. Cu-containing Guinier-Preston (GP) zones and three types of Q′ precursors are identified as most common phases at peak-hardness conditions, whereas β″ accounts for maximum 30% of the total number of precipitates. The precursors have needle (L and S precipitates) or plate (C precipitate) morphologies. They consist of different arrangements of Al, Mg and Cu atoms on a grid defined by triangularly arranged Si planes parallel with and having the same period as {100} Al planes. The Si grid is composed of nearly hexagonal sub-cells of a?=?b?=?4.05?Å, c?=?4.05?Å. The Cu arrangement on the grid is often disordered in the needle precursors. The plate precursor is ordered, with a monoclinic unit cell of a?=?10.32?Å, b?=?8.1?Å, c?=?4.05?Å, γ?=?101°.     

Thermal evolution of short-range order in Cu–Hf-based amorphous alloys

A Perturbed Angular Correlation study on melt-spun Cu₆₀Hf₂₀Ti₂₀ and Cu₆₀Hf₄₀ is presented. The influence of Ti addition on thermal stability and crystallization mechanism is followed by differential scanning calorimetry. The evolution of quadrupole parameters with measurement temperature is analyzed in both alloys in order to get insight into the crystallization process. Although an intricate crystallization mechanism is observed for the Ti containing alloy, the final stage is similar, irrespective of minority atom.