CURE CHARACTERISTICS OF HYDROXYL TERMINATED POLYBUTADIENE PREPOLYMER WITH BLOCKED TOLUENE DIISOCYANATE-Ⅱ

Cure characteristics of hydroxyl terminated polybutadiene (HTPB) prepolymer with avariety of blocked toluene diisocyanate (TDI) in the presence of triethylamine (TEA) andchloroacetic acid catalyst are reported. Phenol, thiophenol, p-chloropheno1, p-nitrophenol,p-cresol, resorcinol, naphthols, caprolactam and butylated-hydroxytoluene were used as blockingagents. Viscosity measurements have been carried out using a mixture of HTPB and blocked TDIin cyclohexanone in the presence of the catalysts at 50℃ and 60℃ using Haake rotational vis-cometer. Viscosity measurements have also been carried out with 50% solids such as ammonium sulphate along with HTPB and TDI adduct.     

Synthesis of hydroxyl-terminated polybutadiene possessing high content of 1,4-units via anionic polymerization

<正>The hydroxyl-terminated polybutadiene(HTPB) possessing high content of 1,4-units was synthesized by anionic polymerization of butadiene,using alkyllithium containing silicon-protected hydroxyl group as initiator and cyclohexane as solvent.The polymers were characterized by GPC,IR and ~1H-NMR.The mechanical properties of cured films were also evaluated.The results show that the content of 1,4-units for HTPBs made by anionic polymerization reaches up to 90%.The molecular weight distribution is very narrow(≤1.05).The functionality of hydroxyl groups approaches 2.Compared with free radical HTPB,the elongation at break of anionic HTPB films increased by 70%,while the tensile strength remained nearly unchanged.This new HTPB can be very useful in solid propellant.     

端羟基聚丁二烯与2,6-甲苯二异氰酸酯固化网络 弹性力学性质的分子模拟

采用最大熵模型, 构建了HTPB预聚物的最可几结构. 考察了HTPB (nC＝9)与TDI全混合以及半混合的两种固化建模方式. 分子动力学模拟得到的HTPB (nC＝9)-TDI固化网络的N—N径向分布函数显示半混模式比全混模式的结构更均匀. 采用分子动力学动态模拟与静态拉伸方法对HTPB (nC＝9)-TDI固化网络进行弹性力学性质的模拟计算. 比较了半混和全混模式对拉伸模量计算的影响, 表明半混模式得到的固化网络能得到合理的模拟结果. 初步表明最大熵模型在研究HTPB固化问题上静态或动态模拟结果都具有唯象可行性.     

HTPB／TDI,HDI聚合反应动力学研究

对端羟基聚丁二烯／甲苯二异氰酸酯，端羟基聚丁二烯／己二异氰酸酯甲苯溶液体系进行了反应动力学研究，用基团分析方法计算了相应体系的活化能，并对无催化剂和有催化剂的体系作了比较。结果表明，二丁基二月桂酸象对上述体系有强的催化作用，使体系的活化能降低，反应速度加快。对于对端差基聚丁二烯／甲苯二异氰酸酯体系，无催化剂时前后期反应活化能分别为２９．１ｋＪ／ｍｏｌ、３７．４ｋＪ／ｍｏｌ，有催化剂时前后期反应活化     

Pot life extension of hydroxyl terminated polybutadiene based solid propellant binder system by tailoring the binder polymer microstructure

A possibility of extending the pot life of the HTPB-TDI based propellant binder system without adverse modification of mechanical properties is explored in the present study. It is proposed that by tailoring functionality distribution of the base HTPB polymer and changing the binder composition concurrently, the pot life of the binder system can be extended while the mechanical characteristics are kept within the acceptability window. Using an existing empirical relationship between fraction of high molecular weight (Fh) in HTPB and r-value corresponding to a more optimized set of mechanical properties, the r-values were calculated for different HTPB resins. HTPB resins with widely varying fractions of high molecular weight (Fh) were chosen and binder networks were prepared at different r values. Viscosity build up and chemical kinetics were studied for different formulations. From the studies, it is shown that the extension of pot-life is achievable by about 150 minutes without sacrificing the mechanical characteristics.     

Metal Sorption,Solid Phase Extraction and Preconcentration Properties of Two Silica Gel Phases Chemically Modified with 2-Hydroxy-1-Naphthaldehyde

Active silica gel phase (I) was chemically modified to the corresponding amino- (SiNH₂) and chloro- (SiCl) derivatives via silylation reactions. These were used to synthesize two newly modified silica gel phases (II, III) by direct chemical reaction with 2-hydroxynaphthaldehyde (2-HNA). The surface coverage values are 370, 432µmolg^–1 and 320, 355µmolg^–1 for (II) and (III), on the basis of thermal desorption and metal probe testing method, respectively. The metal sorption properties of silica gel phases (II, III) were studied and compared with active silica gel phase (I). The maximum determined metal capacity values were found to be 10–110, 20–290 and 20–370µmolg^–1 for phases I, II and III, respectively. The distribution coefficient values (K_d) were also determined for a series of metal ions, and the results showed that the two new chemically modified phases (II and III) were highly selective for Cu²⁺, Zn²⁺, Cd²⁺, Hg²⁺ and Pb²⁺. The potential applications of silica gel phases (II, III) as solid phase extractors for the same five metal ions spiked in drinking tap water (1.000µgmL^–1) were found to give percentage recovery values in the range of 90.2–96.3±4.1–6.3%, while pre-concentration of the same five metal ions spiked in drinking tap water (50.0ngmL^–1) was successfully accomplished with a percentage recovery range of 92.6–95.8±4.8–5.7%.Received December 16, 2002; accepted May 14, 2003 published online September 1, 2003     

CURE CHARACTERISTICS OF HYDROXYL TERMINATED POLYBUTADIENE PREPOLYMER WITH BLOCKED TOLUENE DIISOCYANATE-Ⅰ

Controlled release of TDI and hence the cure characteristics of several blocked TDI with HTPB are reported. The reactions were followed through viscosity measurements as a function of time and temperature under the catalytic influence of triethylamine. The effect of nature of substituents present on the end capping substrate, temperature, solvent, basicity of catalyst and kinetics thereon have been studied.     

丁苯、丁腈基聚氨酯的形态与性能

用示差扫描量热法 (DSC)、红外分光光度计 (FTIR)和原子力显微镜 (AFM)研究了端羟基聚丁二烯 苯乙烯共聚物 (HTBS)、端羟基聚丁二烯 丙烯腈共聚物 (HTBN)和端羟基聚丁二烯 (HTPB)与甲苯二异氰酸酯、1 ,4 丁二醇构成的溶液法聚二烯烃基聚氨酯 (PU)的形态结构 .结果表明HTPB和HTBS基PU的相分离程度很大 ,而HTBN基PU的相分离程度小 .这可能归因于HTBS软段的极性低 ,不能与硬段形成氢键 ,而HTBN软段中的腈基具有很强的极性 ,且可以与硬段形成氢键作用 ,增加了软硬段间的相容性 ,相分离程度明显降低 .AFM表明HTBN PU随着硬段含量提高 ,表面粗糙度增大 ,由软段为连续相逐渐过渡到双连续结构 .在硬段含量 6 3%时 ,HTBN和HTPB基PU均呈双连续结构 ,而HTBS PU中硬段为连续相 .HTBN PU软段的相区尺寸在1 2nm左右 ,表面粗糙度较大 ,HPBS PU软段的相区尺寸在 1 1nm左右 ,表面粗糙度最小 ,HTPB PU存在 1 4nm和 5 0nm大小不等的软段相区尺寸 .力学性能表明 ,在软段中引入苯乙烯和丙烯腈结构 ,可使聚氨酯抗张强度分别提高 1 5和 2倍 ,模量和断裂伸长率也明显提高     

端羟基聚丁二烯和端羟基SBS遥爪聚合物的合成及表征

研究了一种以非极性烃为溶剂,α-甲基萘锂复合物为基体的双锂催化剂LM-T作为引发剂,在环已烷中使丁二烯或丁二烯/苯乙烯进行双活性阴离子聚合,用精制的环氧丙烷终止,合成了双端羟聚丁二烯(HTPB)和双端羟SBS(HTSBS)两种遥爪聚合物。研究结果表明,聚合物分子量和羟基含量可由催化剂用量调整,官能度达到或接近2。分子量分布由GPC测定,宽度指数D=1.4左右。聚合物微观结构通过IR和H-HMR测定,1.4-聚丁二烯含量达到75%左右。因此,HTPB和HTSBS是两种1.4含量较高、分子量分布较窄的离子型遥爪聚合物。     

端羟基聚丁二烯预聚物的表征

本文用VPO、IR、GPC、TLC方法表征国产端羟基聚丁二烯(HTPB),其结果是:Mn为3220,Mw/Mn为1.69,f_n为2.16,f_w为2.27。证明国产HTPB预聚物的数均官能度随分子量增加而增加。探讨了用TLC法研究HTPB官能度分布的可靠性。     

热动力学方法测定端羟基聚丁二烯固化反应动力学参数

用热动力学方法对高分子固化反应动力学进行研究,在RD-Ⅰ型热导式自动量热计的基础上,设计了反应器,测定了端羟基聚丁二烯(HTPB)与甲苯二异氰酸酯(TDI)固化反应的动力学参数(表观活化能和反应速率常数),结果与文献值、粘度法和红外光谱法的结果相符。     

正电子湮没谱研究聚烯烃聚氨酯的自由体积、微观结构和溶剂的扩散行为

用正电子湮没技术(PAS)结合示差扫描量热法(DSC)研究了聚烯烃聚氨酯的自由体积特征和微相分离结构的关系.结果表明,硬段含量增加,自由体积孔洞平均半径和自由体积分数减小;丁腈聚氨酯相分离程度小,相应自由体积孔洞平均半径和自由体积分数小,而丁羟聚氨酯的情况正好相反.石英弹簧法对苯和乙醇蒸气的溶解和扩散行为的研究表明,聚烯烃聚氨酯的自由体积孔洞平均半径和自由体积分数与苯和乙醇溶剂蒸气的无限稀释扩散系数呈正相关,但它们的无限稀释扩散系数和自由体积分数关系无法用Fujita的自由体积模型描述,可能归因于它们对聚烯烃聚氨酯复杂的溶胀行为.     

利用扭辫分析法对液体丁羟胶固化的研究(Ⅰ)

本工作用扭辫分析(TBA)技术研究了端羟基聚丁二烯(HTPB)-甲苯二异氰酸酯(TDI)体系的固化反应表现动力学,得到了该反应的表观活化能,并用粘度和红外光谱测定作了验证,认为TBA技术用于研究液体橡胶固化问题是一种有意义的方法。     

理论研究丁羟粘合剂化学键解离及其对力学性能的影响

端羟基聚丁烯(HTPB)是推进剂中的常用的粘合剂,老化是其贮存和使用中的重要问题。通过量子化学计算HTPB 与甲基二异腈酸酯(TDI)形成的网络模型简化结构中化学键的均裂解离能(BDE),分析了键能与老化分解的关系。键能计算结果证明可靠且可用于比较分析。与CH₂ 基团相连的C-O 键的BDE值最小,推测该键最弱并且在热老化过程会发生断裂分解,降解产物主要是CO₂。HTPB 中的烯丙基伯羟基与TDI 形成的聚氨酯中α-C-H 属于最弱的X-H(X=C, N)键,推测其容易受到自由基的进攻发生氢转移反应。对容易断裂分解的C-O 键,提出了可能的老化机理。计算的C-O 键断裂活化能与其解离能近似相等,热老化过程中断键生成自由基并通过无势垒过程释放出CO₂。整个过程的热老化半衰期是温度的指数衰减函数,表明随着温度的提高HTPB-TDI 聚氨酯老化加速。热力学计算证明老化形成的氨基自由基和烷基自由基能够重新结合。采用分子动力学动态分析方法,分析了HTPB-TDI 聚氨酯网络老化前后的结构变化及其对弹性力性质的影响,发现释放CO₂ 的过程伴随着体系密度降低。对假定的CO₂ 扩散聚集以及CO₂ 从体系中扩散消失的模型进行了模拟,发现拉伸模量和剪切模量在这两种情形下会增加。     

Improving the Mechanical Properties of Glycidyl Azide Polymeric Matrix Used in Composite Solid Rocket Propellant by Adding Advanced Cross‐Linker

Glycidyl azide polymer (GAP) based binders have poor mechanical characteristics in comparison with hydroxyl terminated polybutadiene (HTPB) binders. In this study, advanced cross‐linker was used to improve the mechanical properties of GAP binder. GAP was prepared and characterized in comparison with HTPB prepolymer. Density, characteristics groups, nitrogen content, humidity, viscosity, and milligram equivalent of (OH) per binders were determined. A cross‐linker consists of trimethylol propane (TMP) and curing catalyst, dibutyltin dilaurate (DBTDL), was used as an additive to GAP polymeric matrix to enhance its functionality. Polymeric matrices based on GAP and HTPB were prepared with different curing ratio (NCO/OH) ranging from 0.7 to 1.5. Different weight percentages of cross‐linker were added to study its effect on the mechanical properties of GAP matrix. Five samples based on HTPB polymer and twenty samples based on GAP polymer were prepared. A LLOYD testing machine was used to determine the stress‐strain curves of all the studied samples. It was concluded that the cross‐linker used has significant influence on the characteristics of GAP polymeric matrix. Also the addition of 5 wt % of cross‐linker to GAP matrix at curing ratio = 1 produced optimum mechanical characteristics very close to that of HTPB matrix used in composite solid rocket propellants (CSRP). The optimum GAP polymeric matrix is candidate to replace the traditional HTPB binder in advanced CSRP.     

Synthesis and properties of aromatic secondary amine-blocked isocyanates

N-Methylaniline-, diphenylamine-, and N-phenylnaphthylamine-blocked toluene diisocyanates (TDI) were prepared and characterized by IR, NMR spectroscopy, and nitrogen content analyses. The structure–property relationship of these adducts was established by reacting with hydroxyl-terminated polybutadiene (HTPB). The cure rate of the adduct increases from the N-phenylnaphthylamine- to diphenylamine- and to N-methylaniline-blocked TDI adduct. Simultaneous TGA/DTA results also confirm this trend, and the thermal stability of the adduct decreases in the following order: N-phenylnaphthylamine–TDI > diphenylamine–TDI > N-methylaniline–TDI. The gas chromatogram of the amine-blocked isocyanate confirms that the thermolysis products are the blocking agent and isocyanate. The solubilities of the adducts were carried out in polyether, polyester, and hydrocarbon polyols, and it was found that the N-methylaniline–TDI adduct shows higher solubility than the rest and also found that the polyester polyol shows higher solvating power against the adducts than the polyether and hydrocarbon polyols. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1815–1821, 1999     

Study on Reaction of Tolylene Diisocyanate with Polyolefine Polyols

Polyurethane(PU) has been used widely. It is produced by polyisocyanate with polyol. There are many polyisocyanates and polyols. For polyols it is mainly concentrated on polyester and polyether, there is any study on polyolefine polyol. The paper mainly discuss it.By using tolylene diisocyanate(TDI,C6H4CH3(NCO)2) to react with hydroxyterminated polybutadiene(HTPB,HO-[-CH2-CH=CH-CH2-]n-OH,Mn=3805,) and hydroxy-terminated poly(butadiene-co-acrylonitrile)(HTBN, HO-[(-CH2-CH=CHCH2-)x-(-CHCN-CH2)y-]n-OH,Mn=2267), various NCO/OH equivalent ratio NCOterminated polyurethane(PU) prepolymers are synthesized.     

Unsaturated poly(ester-imide)s from hydroxy-terminated polybutadiene, dianhydride and diisocyanate

Hydroxy terminated polybutadiene has been used for the first time in the synthesis of poly(ester-imide)s [P(E-I)s]. Anhydride terminated polyester prepolymers were prepared by the reaction of two different polyols--polytetramethyleneoxide glycol (PTMG) of molecular weight 1000 and hydroxy terminated polybutadiene (HTPB) of molecular weight 2500--and different dianhydrides--pyromellitic dianhydride (PMDA), benzophenonetetracarboxylic dianhydride (BTDA) and 4,4^′-(hexafluoroiso-propylidene)diphthalic anhydride (HFDA). The prepolymers were then reacted with different diisocyanates--80:20 mixture of 2,4- and 2,6-tolylene diisocyanate (TDI), 1,6-hexamethylene diisocyanate (HDI), isophorone diisocyanate (IPDI) and 4,4^′-methylene bis(phenylisocyanate) (MDI) resulting in P(E-I)s. The P(E-I)s were characterised by FT-IR, FT-NMR, GPC, TGA, DSC and for static and dynamic mechanical properties. The polymers based on PTMG showed two distinct melting points and behave as thermoplastic elastomers. The thermal stability and mechanical properties of P(E-I)s based on HTPB were substantially higher than those based on PTMG.     

羟基聚丁二烯羟值测定新方法

本文建立了两个相关的∑Aa_i-B_2型凝胶化反应方程,含试样官能团数和重均官能度两个未知数.解联立方程,得到一元二次方程.通过测定该方程的系数,间接测得试样官能团数和重均官能度.该方法用于H_2O_2引发的羟基聚丁二烯羟值测定。其结果比目前国内外通用的经典酰化法高一倍以上.证明新的羟值数据是正确的.     

Diol-diisocyanate polymerization by gamma irradiation

Gamma irradiation has been used as an alternative way of curing diol-diisocyanate by means of specific catalysts and/or elevated temperatures. A mixture of toluene diisocyanate (TDI) and hydroxy terminated polybutadiene (HTPB) oligomer were irradiated over a dose range of 0–720 kGy using a 5 kCi⁶⁰Co -source. Various compositions were formulated and also suitable additives were incorporated. Disappearance of the isocyanate peak in the IR spectra was considered as a measure of its consumption. The conversion characteristics showed a profound influence of irradiation. A suitable mechanism is envisaged.