Silicon surface nano-oxidation using scanning probe microscopy

This paper focuses on the nano-oxidation of a silicon surface using scanning probe microscopes in air ambient and in UHV. Special emphasis is put in air ambient on the preparation of the surfaces and on the oxidation mechanism. The characteristics of the patterned nanostructures are reviewed versus the parameters which govern the process (tip–surface voltage, tip speed, humidity) as well as the kinetics models of the oxidation process. The oxide patterns can act as robust masks for dry or wet etching. Fabrication of nanostructures is presented and allows to realize electronic nanodevices. In UHV, there is no direct nano-oxidation of the surface by the microscope tip. First the surface is hydrogenated, second a local hydrogen desorption is performed with the STM tip and finally the bare desorbed area is exposed to oxygen. The desorption process is analyzed versus tip–surface voltage and tunneling current. The oxidation of a desorbed area using molecular or atomic oxygen is actually difficult to achieve.     

The use of in situ techniques in R&;D of Li and Mg rechargeable batteries

Rechargeable batteries are complicated devices in which three bulk zones (electrodes, electrolyte solution) and two interfaces have to work simultaneously and coherently, without any side reactions. The study of electrode materials and electrode–solution interfaces of rechargeable batteries requires the use of first-rate techniques for structure and surface analysis, in conjunction with electrochemical methods. The use of in situ techniques in which spectroscopy, diffractometry, or microscopy are measured in conjunction with an electrochemical response may be highly important and beneficial for battery research. We review herein the use of in situ Fourier transform–infrared spectroscopy, Raman, X-ray absorption, mass spectrometry, X-ray diffraction, atomic force microscopy, scanning tunneling microscopy, and electrochemical quartz crystal microbalance techniques for research and development of rechargeable Li and Mg batteries.     

Raman-STM联用系统及其初步实验

研究固／液界面体系的传统方法主要以电信号为激励和检测手段，已不能适应日益扩大的研究对象和深入至微观研究的要求，许多采用电子束或离子束作为人射源的表面技术由于x作在高真空条件下也难以原位（insitu）研究固／液体表由于光束容易穿过团／液体系的溶液层或具有光学透明的固体电极材料，八十年代以来以光（尤其是激光）作为激励和检测手段的研究方法日益受到重视[1]，目前已开展的工作包括光电流（电压、电容）谱、光发射电流话、光声（热）谱、反（透）射谱、全息谱、瑞利散射、（超）拉曼散射、二次谐波（SHG）以及和频（SFG）…     

Assembly and electrochemical characterization of nanometer-scale electrode|solid electrolyte interfaces

A technique is herein described for the assembly and characterization of nanometer-scale metal electrode|solid electrolyte interfaces of variable dimensions. The specific system examined in this work involves a sharp Pt tip attached to the piezo-driven head of a scanning tunneling microscope (STM) allowing the tip to be inserted into (or retrieved from) a Nafion membrane placed normal to the direction of tip travel. The actual Pt|Nafion area of contact was determined by coulometric analysis of the characteristic voltammetric features of Pt, using the tip as the working electrode and a much larger Pt gauze attached to the other side of the Nafion as a counter-reference electrode, yielding for some of the interfaces examined values equivalent to as low as 35 000 Pt surface atoms. This rather versatile arrangement allows experiments to be performed in both inert (Ar) and reactive atmospheres, such as oxygen or hydrogen on either or both sides of the membrane, under controlled humidity conditions, and thus sheds light into such phenomena as changes in the overall faradaic currents induced by plastic deformations of the Nafion as well as fundamental aspects of mass transport at reactant gas|Pt|Nafion three-boundary interfaces of relevance to polymer electrolyte fuel cells (PEFCs).     

Reduction-induced switching of single-molecule conductance of fullerene derivatives

The effect of electrochemical reduction on the single-molecule conductance of fullerene C60 derivatives was studied by scanning tunneling microscopy. Three types of C60 derivatives were synthesized, a monoadduct having an amino-terminated linker and two bisadducts having two linkers at different positions (trans2 and trans3). Each C60 derivative was immobilized on a gold surface by an amino-gold linkage, confirmed by infrared reflection-absorption spectroscopy. The immobilized C60 derivatives showed reversible and multiple reduction peaks in the cyclic voltammogram in dimethylformamide (DMF) at almost the same potentials as those in solution, showing the redox properties of the molecules are intact on gold. Single-molecule conductances of the bisadducts, which can span between a scanning tunneling microscopy (STM) tip made of gold and substrate with the two linkers, were determined by the STM break-junction measurements in water and DMF. The conductances were 6.1+/-4.5 nS in water and 4.9+/-1.7 nS in DMF for the trans2 bisadduct and 8.4+/-3.4 nS in water and 7.9 nS+/-2.8 in DMF for the trans3 bisadduct. By using a potential-controlled STM setup, the tunneling current through a single molecule was recorded with sweeping the potentials of the tip and substrate. The trans2 bisadduct showed significant changes in the current when the reductions of the C60 moiety occur. Some current curves showed multiple peaks, and the other curves showed stepwise increase and decrease at the C60 reduction and subsequent reoxidation. Statistical analysis afforded stepwise switching of the conductance as the average behavior and suggested that the electron tunneling through the C60 derivative is enhanced as it accepts electrons.     

Electrical behavior of molecular junctions incorporating alpha-helical peptide

We synthesized an alpha-helical peptide containing two terminal thiol groups and demonstrated the method of preparation of a self-assembled monolayer (SAM) on gold with uniform orientation of the molecules on the surface. The monolayers were employed as model systems for the investigations of mediated electron transfer. The measurements of electron transfer efficiency through the peptide were performed using scanning tunneling spectroscopy (STS). The molecules were trapped between the gold tip and the substrate using a Au-S linkage. The electron transfer behavior of the peptide was examined as a function of the tip-substrate distance at fixed bias voltage and as a function of bias voltage at a fixed distance between the tip and the substrate. The data obtained from these experiments indicated that the electron transfer through alpha-helical peptide is very efficient, and its conductivity is comparable to those observed for dodecanedithiol. There is also a directional dependence of electron transmission through the peptide, which is connected with the electric field generated by the molecular dipole of the helix.     

Low-frequency surface-enhanced Raman scattering spectroscopy at metal electrode surfaces

Low-frequency surface-enhanced Raman scattering (SERS) spectroscopy is a versatile tool for studying surface phenomena under electrochemical conditions. This spectroscopy enables us to obtain rich information on extramolecular vibrations between substrate and adsorbates, which are sensitive to atomistic surface features of the substrate. Owing to recent advancements in optical filter technology, low-frequency SERS signals are now becoming easily detectable using conventional Raman systems equipped with holographic notch filters. In addition, SERS background signals, which have been simply ignored, can provide electronic information on the metal substrate. This allows us to observe both sides of electrode–electrolyte interfaces in situ and simultaneously, which is never expected in far-infrared or terahertz absorption spectroscopy. This advanced SERS spectroscopy can help our understanding of electrochemical and electrocatalytic reactions at the molecular scale.     

Evanescent wave cavity-based spectroscopic techniques as probes of interfacial processes

Evanescent wave cavity ring-down spectroscopy (EW-CRDS) is a surface sensitive technique, which allows optical absorption measurements at interfaces with good time resolution. In EW-CRDS, a pulsed or modulated laser beam is coupled into an optical cavity which consists of at least one optical element, such as a silica prism, at the surface of which the beam undergoes total internal reflection (TIR). At the position of TIR, an evanescent field is established whose amplitude decays exponentially with distance from the boundary. This evanescent field can be exploited to investigate interfacial properties and processes such as adsorption and surface reactions, with most applications hitherto focusing on solid/liquid and solid/air interfaces. As highlighted herein, EW-CRDS is particularly powerful for investigations of interfacial processes when combined with other techniques such as basic electrochemical measurements and microfluidic or hydrodynamic techniques. In this tutorial review, the basic elements of EW-CRDS will be introduced and the relative merits of different configurations for EW-CRDS discussed, along with various aspects of instrumentation and design. The type of information which may be obtained using EW-CRDS is illustrated with a focus on recent examples such as molecular adsorption/desorption, deposition/dissolution of nanostructures and interfacial redox reactions. The comparatively new, but complementary, cavity technique of EW-broadband cavity enhanced absorption spectroscopy (EW-BB-CEAS) is also introduced and its advantages compared with EW-CRDS are discussed. Finally, future developments and trends in EW-cavity based spectroscopy are predicted. Notably, the potential for extending the technique to probe other interfaces is exemplified with a discussion of initial interfacial absorbance measurements at a water-air interface.     

Electron transport analysis for improvement of solid-state dye-sensitized solar cells using poly(3,4-ethylenedioxythiophene) as hole conductors

Dye-sensitized solar cells (DSCs) using solid-state hole conductor, poly(3,4-ethylenedioxythiophene) (PEDOT), were fabricated using in-situ photoelectrochemical polymerization giving short-circuit photocurrent density of 3.20 mA cm-2, open-circuit voltage of 0.77 V, and fill factor of 0.50, and the resulting overall conversion efficiency of 1.25% on average under air mass 1.5 conditions. Furthermore, the electron transport properties of the DSCs based on PEDOT (PEDOT/DSCs) were analyzed using light intensity modulation induced photocurrent and photovoltage decay (SLIM-PCV) measurements and electrochemical impedance spectroscopy (EIS) measurements, and then compared to those of the DSCs based on organic liquid electrolyte containing I-/I3- as redox couple (liquid iodide/iodine electrolyte-DSCs, iodide/DSCs for short). The effective filling of PEDOT in the mesopores of dyed TiO2 layers is an important key to achieve the respectable conversion efficiency of PEDOT/DSCs that is comparable with iodide/DSCs.     

Electrocatalytic and magnetic properties of ultrathin nanostructured iron-melanin films on Au(111)

We have prepared ultrathin, nanostructured melanin films on Au(111) by means of electrochemical self-assembly. These films were characterized by using Auger electron spectroscopy, X-ray absorption near-edge structure spectroscopy, scanning tunneling microscopy, magnetic force microscopy, and electrochemical techniques. Two types of nanostructures are present in the film: melanin nanoparticles and Fe(3)O(4) nanoparticles. The melanin nanoparticles contain Fe bonded to oxygen-containing phenolic groups in an octahedral configuration similar to that found in Fe(2)O(3). The inorganic-organic composite exhibits magnetic properties and catalyzes the electroreduction of hydrogen peroxide in alkaline and neutral electrolyte solutions. The electrocatalytic activity depends on the Fe-bound melanin and appears to be similar to that found for Fe-porphyrins.     

Engineering large-scaled electrochromic semiconductor films as reproductive SERS substrates for operando investigation at the solid/liquid interfaces

Although surface-enhanced Raman spectroscopy (SERS) has been applied for gathering fingerprint information, even in single molecule analysis, the decayed Raman signals in aqueous solutions largely obstruct the on-site insight reaction process. In this study, large-scaled semiconductor films with multi-walled (TiO₂/WO₃/TiO₂) nanopore distribution are fabricated by combining electrochemical anodization and sputtering technique, and then employed as the SERS substrates for detection of molecules at the solid/liquid interfaces. Given the remarkably improved electrochromic property of the multi-walled film, such SERS substrates were endowed with tunable oxygen vacancy (V_O) density and distribution via simply applying electrochemical bias voltage, which enabled one to achieve an enhanced charge transfer efficiency and thus a remarkably increased Raman signal even in solution. The V_O-rich SERS substrate is highly repeatable, thus providing a reliable platform for in-situ monitoring of the target molecules or intermediates at the solid/liquid interfaces.     

Water-in-salt electrolytes: An interfacial perspective

Liquid electrolytes with high ionic conductivity, high transference number for the target ions, and excellent electrochemical, chemical, and thermal stability are essential for electrochemical energy storage devices. Water-in-salt (WIS) electrolytes, in which the salt–water ratio is larger than one, are gaining intensive attention in the electrochemical community. Here, we review the recent work on WIS electrolytes and the closely related water-in-ionic liquid electrolytes. We highlight the fact that many properties of these electrolytes, in bulk and at electrolyte–electrode interfaces, are underpinned by the physics and chemistry of the interfaces formed between water and ions (or aggregated water/ion clusters). Manipulating these interfaces by tailoring the selection of ions and water–ion ratio opens up new dimensions in the optimization of liquid electrolytes but also poses new challenges. We conclude the review by highlighting several directions for research on WIS electrolytes, in particular, the study of WIS electrolyte–electrode interfaces using surface force measurements.     

Electrochemistry of nano-scale bacterial surface protein layers on gold

The mechanism of the recrystallization of nano-scale bacterial surface protein layers (S-layers) on solid substrates is of fundamental interest in the understanding and engineering of biomembranes and e.g. biosensors. In this context, the influence of the charging state of the substrate had to be clarified. Therefore, the electrochemical behaviour of the S-layers on gold electrodes has been investigated by in-situ electrochemical quartz microbalance (EQMB) measurements, scanning force microscopy (SFM) and small-spot X-ray photoelectron spectroscopy (SS-XPS) of potentiostatically emersed substrates. It was shown that the negatively charged bonding sites of the S-layer units (e.g. carboxylates) can bond with positively charged Au surface atoms in the positively charged electrochemical double layer region positive of the point of zero charge ( approximately -0.8 V vs. saturated mercury-mercurous sulphate electrode). Surface conditions in other potential regions decelerated the recrystallization and fixation of S-layers. Time-resolved in-situ and ex-situ measurements demonstrated that two-dimensional S-layer crystal formation on gold electrodes can occur within few minutes in contrast to hours common in self-assembled monolayer (SAM) generation. These results proved that the recrystallization and fixation of 2D-crystalline S-layers on an electronic conductor can be influenced and controlled by direct electrochemical manipulation.     

Voltage-Height Spectroscopy in the <Emphasis Type="Italic">Ex Situ</Emphasis> Configuration of a Scanning Tunneling Microscope

Basic regularities of electrochemical processes in the gap of an ex situ scanning tunneling microscope in conditions of condensation of air moisture at the sample surface are considered on a qualitative level. A layer of condensed moisture is viewed as an electrolyte in a two-electrode cell. The depolarizers present in this layer may experience electrochemical conversions on the tip and in an area of the sample surface near the tip. As a result, the recorded “tunneling” current includes electrochemical constituents. Depending on the electrochemical processes in the gap, various dependences of the tip-sample distance on the current and applied voltage can be expected. For preliminary diagnostics of processes in the gap it is suggested to use voltage-height spectra, whose shape and characteristic heights are sensitive to the nature and location of redox active species. Experimental data for various films on conducting supports (quasi-two-dimensional adsorbed layers of hemin and peroxidase, electrodeposited nonstoichiometric tungsten oxides, doped tin dioxide, solid electrolyte with ionic conduction) are presented as an examples.__________Translated from Elektrokhimiya, Vol. 41, No. 5, 2005, pp. 583–595.Original Russian Text Copyright © 2005 by Yusipovich, Vassiliev.     

Thin-film voltammetry and its analytical applications: A review

Electrochemical reactions at the interfaces of immiscible electrolyte solutions (ITIES) are of fundamental importance in the fields of chemical, biological and pharmaceutical sciences. Four-electrode cell setup, scanning electrochemical microscopy (SECM) and thin-film voltammetry are the three most frequently used methods for studying the electrochemical processes at these interfaces. The principle, experimental design, advantages and challenges of the three methods are described and compared. The thin-film voltammetry is highlighted for its simplicity in experimental operation and kinetic data analysis. Its versatile analytical applications are discussed in detail, including the study of redox properties of hydrophobic compounds, evaluation of interfacial electron transfer kinetics, synthesis of nanoparticles/nanostructures, and illustration of cross-membrane ion transport phenomena.     

Surface and electrochemical analysis for the understanding of TiO2 nanopores/nanotubes changes in post‐elaboration treatment

The electrochemical stability of TiO₂ nanoarchitecture fabricated in fluoride electrolyte presented in this paper is related to 2D and 3D geometries that present a shift from nanopores toward nanotubes. The fabrication conditions involve a 60 V applied voltage for 2 hours of anodizing in order to create the ordered structures, in a mixture of low‐water glycerol electrolyte and fluoride. With the use of different ultrasonication times, a variety of nanotubes/nanopores were observed. The surface interfacial aspects were investigated mainly by surface microscopy and hydrophilic/hydrophobic balance for the grown structures ultrasonicated at various periods of time. The electrochemical behavior of the nanotube‐structured surface was performed by potentiodynamic evaluation and electrochemical impedance spectroscopy in a simulated body fluid solution. As a most important result, all surface analysis and electrochemical data interpretation permitted the proposition of a model for elaboration of different nanostructures from nanopores to nanotubes. These different surface nanoarchitectures were obtained as a result of ultrasonication at various periods of time. Copyright © 2010 John Wiley & Sons, Ltd.     

Remarkable support effect of SWNTs in Pt catalyst for methanol electrooxidation

Carbon nanotubes have been proposed as advanced metal catalyst support for electrocatalysis. In this work, different carbon support materials including single-walled carbon nanotubes (SWNTs), multi-walled carbon nanotubes (MWNTs) and XC-72 carbon black, were compared in terms of their electrochemical properties using cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The SWNTs is found to exhibit the highest accessible surface area in electrochemical reactions and the lowest charge transfer resistance at the SWNTs/electrolytes. These carbon materials are then loaded with varying amount of Pt by the electrodeposition technique to prepare carbon supported Pt catalysts. Electrochemical measurements of methanol oxidation reveal that the SWNTs supported Pt catalyst exhibits the highest mass activity (mA/mg-Pt). In comparison with Pt-XC-72 and Pt-MWNTs, the remarkably enhanced electrocatalytic activity of the Pt-SWNTs maybe attributed to a higher dispersion and utilization of the Pt particles, which are directly related to the electrochemical characteristics of SWNTs. The high concentration of oxygen-containing functional groups, high accessible surface area, low charge transfer resistance at the carbon/electrolyte interfaces can be important for the Pt dispersing and strong metal-support interaction in the Pt-SWNTs catalyst.     

Topography Structure and Scanning Tunneling Spectrum of Nickel(Ⅱ)-tetraphenylporphyrin Molecules on Au(111)

Scanning tunneling microscopy (STM) and scanning tunneling spectroscopy (STS) were performed on monolayer film of NiTPP supported on Au(111) under ultrahigh vacuum (UHV) conditions. The constant current STM images show remarkable bias dependence. High resolution STM data clearly show the individual NiTPP molecules and allow easy differentiation between NiTPP and CoTPP reported before. Scanning tunneling spectra, as a function of molecule-tip separation, were acquired over a range of tip motion of 0.42 nm. Spectra do not show the variation in band splitting with tip distance. It appears for molecules such as NiTPP that the average potential at the molecule is essentially the same at the same metal substrate. For molecules of the height of NiTPP, the scanning tunneling spectra should give reliable occupied and unoccupied orbital energies over a wide range of tip-molecule distances.     

Nanoscale Chemical Imaging Using Tip‐Enhanced Raman Spectroscopy: A Critical Review

Methods for chemical analysis at the nanometer scale are crucial for understanding and characterizing nanostructures of modern materials and biological systems. Tip‐enhanced Raman spectroscopy (TERS) combines the chemical information provided by Raman spectroscopy with the signal enhancement known from surface‐enhanced Raman scattering (SERS) and the high spatial resolution of atomic force microscopy (AFM) or scanning tunneling microscopy (STM). A metallic or metallized tip is illuminated by a focused laser beam and the resulting strongly enhanced electromagnetic field at the tip apex acts as a highly confined light source for Raman spectroscopic measurements. This Review focuses on the prerequisites for the efficient coupling of light to the tip as well as the shortcomings and pitfalls that have to be considered for TERS imaging, a fascinating but still challenging way to look at the nanoworld. Finally, examples from recent publications have been selected to demonstrate the potential of this technique for chemical imaging with a spatial resolution of approximately 10 nm and sensitivity down to the single‐molecule level for applications ranging from materials sciences to life sciences.     

Conductance of alpha-helical peptides trapped within molecular junctions

Self-assembled monolayers of alpha-helical peptides on a gold surface were employed as model systems for the investigation of mediated electron transfer. The peptides contained 14, 15, 16, and 17 amino acid residues. The measurements of electron transmission through single molecules of helical peptides were performed using scanning tunneling spectroscopy (STS). The molecules were trapped between the gold tip and the substrate. Electrical contact between the molecule and the gold probe was achieved by the use of peptides containing thiol groups present at each end of the helix. The conductance behavior of the peptides was examined as a function of tip-substrate distance at fixed bias voltage. Measurements performed with peptides containing different numbers of amino acid residues indicate that the distance dependence of electron transmission through an alpha-helix is weaker than that through simple n-alkyl bridges.