An indentation technique for estimating the energy density as fracture toughness with Berkovich indenter for ductile bulk materials

A technique is proposed to estimate the energy density as fracture toughness for ductile bulk materials with an indentation system equipped with a Berkovich indenter based on the theory of plastic deformation energy transforming into the indentation energy of fracture. With progressive increase of penetration loads, the material damage is exhibited on the effective elastic modulus. A quadratic polynomial relationship between the plastic penetration depth and penetration load, and an approximate linear relationship between logarithmic plastic penetration depth and logarithmic effective elastic modulus are exhibited by indentation investigation with Berkovich indenter. The parameter of damage variable is proposed to determine the critical effective elastic modulus at the fracture point. And the strain energy density factor is calculated according to the equations of penetration load, plastic penetration depth and effective elastic modulus. The fracture toughness of aluminum alloy and stainless steel are evaluated by both indentation tests and K_IC fracture toughness tests. The predicted S_cr values of indentation tests are in good agreement with experimental results of CT tests.     

高载下单晶铜和单晶硅的径向纳动与损伤行为研究

采用纳米压痕仪研究了单晶铜和单晶硅径向纳动的运行特点和损伤过程.结果表明:径向纳动的残余压痕深度随循环次数增加急剧减小,而纳动循环中载荷-位移曲线在闭合前表现为1个迟滞环;试样在首次径向纳动循环中耗散的能量最大,其后逐渐减小并趋于稳定;材料的接触刚度和弹性模量在最初几次纳动循环中增加较快,随后变化趋于平缓;尽管2种材料的压痕投影面积均随纳动循环次数增加而增大,但由于损伤机制不同,使其径向纳动损伤显示出各自不同特点,其中单晶铜主要表现为压痕边缘的皱褶堆积,而单晶硅表现为塑性区边界裂纹的萌生与扩展.     

利用纳米硬度试验法确定Cr/Cu梯度材料的变形特性

利用纳米硬度仪研究了在Cu基底上的Cu／Cr梯度膜的机械性能。梯度膜是通过将Cu靶和Cr靶同时溅射到Cu基底材料上，但两个靶的相对溅射功率随溅射时间变化而制备。利用Oliver and Pharr方法得到了膜随其厚度变化的硬度和弹性模量。然后利用加载／卸载／再加载的方法得到了在不同深度(即膜的厚度)压头平均压力与相对压人深度之间的关系曲线，在此曲线上可以明显反映出材料的屈服特性。     

基于应变率阶跃测试的晶体铜压入应变率敏感性研究

纳米压入测试可以原位获取材料的诸多力学性能,包括弹性模量,硬度,屈服应力,应变率敏感指数等。本文利用应变率阶跃测试技术对多晶铜试样的应变率敏感性进行测试分析,硬度-位移曲线表明压头下方所存在的变形梯度对各阶跃应变率下的硬度值存在明显影响;采用基于晶体细观机制的塑性应变梯度理论对压入变形梯度效应予以修正,比较了修正与未修正数据所得的应变率敏感指数,在有效剔除压入变形梯度影响的基础上,应变率阶跃测试可实现单次压入下材料应变率敏感性的测试表征。     

Evaluation of the stress–strain curve of metallic materials by spherical indentation

A method for deducing the stress–strain uniaxial properties of metallic materials from instrumented spherical indentation is presented along with an experimental verification.An extensive finite element parametric analysis of the spherical indentation was performed in order to generate a database of load vs. depth of penetration curves for classes of materials selected in order to represent the metals commonly employed in structural applications. The stress–strain curves of the materials were represented with three parameters: the Young modulus for the elastic regime, the stress of proportionality limit and the strain-hardening coefficient for the elastic–plastic regime.The indentation curves simulated by the finite element analyses were fitted in order to obtain a continuous function which can produce accurate load vs. depth curves for any combination of the constitutive elastic–plastic parameters. On the basis of this continuous function, an optimization algorithm was then employed to deduce the material elastic–plastic parameters and the related stress–strain curve when the measured load vs. depth curve is available by an instrumented spherical indentation test.The proposed method was verified by comparing the predicted stress–strain curves with those directly measured for several metallic alloys having different mechanical properties.This result confirms the possibility to deduce the complete stress–strain curve of a metal alloy with good accuracy by a properly conducted instrumented spherical indentation test and a suitable interpretation technique of the measured quantities.     

Simulations of nanowire bend tests for extracting mechanical properties

Mechanical properties of nickel nanowires are characterized based on the numerical simulations of bend tests performed with a customized atomic force microscope (AFM) and scanning electron microscope (SEM). Nickel nanowire specimens are subjected to bending loads by the tip of the AFM cantilever. The experimental force versus bending displacement curves are compared against simulations from finite element analysis and peridynamic theory, and the mechanical properties are extracted based on their best correlations. Similarly, SEM images of fractured nanowires are compared against peridynamic failure simulations. The results of this study reveal that nickel nanowires have significantly higher strengths than their bulk counterparts, although their elastic modulus values are comparable to bulk nickel modulus values.     

Two new expanding cavity models for indentation deformations of elastic strain-hardening materials

Two expanding cavity models (ECMs) are developed for describing indentation deformations of elastic power-law hardening and elastic linear-hardening materials. The derivations are based on two elastic–plastic solutions for internally pressurized thick-walled spherical shells of strain-hardening materials. Closed-form formulas are provided for both conical and spherical indentations, which explicitly show that for a given indenter geometry indentation hardness depends on Young’s modulus, yield stress and strain-hardening index of the indented material. The two new models reduce to Johnson’s ECM for elastic-perfectly plastic materials when the strain-hardening effect is not considered. The sample numerical results obtained using the two newly developed models reveal that the indentation hardness increases with the Young’s modulus and strain-hardening level of the indented material. For conical indentations the values of the indentation hardness are found to depend on the sharpness of the indenter: the sharper the indenter, the larger the hardness. For spherical indentations it is shown that the hardness is significantly affected by the strain-hardening level when the indented material is stiff (i.e., with a large ratio of Young’s modulus to yield stress) and/or the indentation depth is large. When the indentation depth is small such that little or no plastic deformation is induced by the spherical indenter, the hardness appears to be independent of the strain-hardening level. These predicted trends for spherical indentations are in fairly good agreement with the recent finite element results of Park and Pharr.     

The Influence of Indenter Tip Imperfection and Deformability on Analysing Instrumented Indentation Tests at Shallow Depths of Penetration on Stiff and Hard Materials

We report on the difficulties of extracting plastic parameters from constitutive equations derived by instrumented indentation tests on hard and stiff materials at shallow depths of penetration. As a general rule, we refer here to materials with an elastic stiffness more than 10 % of that of the indenter and a yield strain higher than 1 %, as well as to penetration depths less than ～ 5 times the characteristic tip defect length of the indenter. We experimentally tested such a material (an amorphous alloy) by nanoindentation. To describe the mechanical response of the test, namely the force-displacement curve, it is necessary to consider the combined effects of indenter tip imperfections and indenter deformability. For this purpose, an identification procedure has been carried out by performing numerical simulations (using Finite Element Analysis) with constitutive equations that are known to satisfactorily describe the behaviour of the tested material. We propose a straightforward procedure to address indenter tip imperfection and deformability, which consists of firstly taking account of a deformable indenter in the numerical simulations. This procedure also involves modifying the experimental curve by considering a truncated length to create artificially the material’s response to a perfectly sharp indentation. The truncated length is determined directly from the loading part of the force-displacement curve. We also show that ignoring one or both of these issues results in large errors in the plastic parameters extracted from the data.     

Analysis of elastic and plastic deformation associated with indentation testing of thin films on substrates

A study has been made of the elastic and plastic deformation associated with submicrometer indentation of thin films on substrates using the finite element method. The effects of the elastic and plastic properties of both the film and substrate on the hardness of the film/substrate composite are studied by determining the average pressure under the indenter as a function of the indentation depth. Calculations have been made for film/substrate combinations for which the substrate is either harder or softer than the film and for combinations for which the substrate is either stiffer or more compliant than the film. It is found, as expected, that the hardness increases with indentation depth when either the yield strength or the elastic modulus of the substrate is higher than that of the film. Correspondingly, the hardness decreases with indentation depth when the yield strength or elastic modulus of the substrate is lower than that of the film. Functional equations have been developed to predict the hardness variation with depth under these different conditions. Finite element simulation of the unloading portion of the load displacement curve permits a determination of the elastic compliance of the film/substrate composite as a function of indentation depth. The elastic properties of the film can be separated from those of the substrate using this information. The results are in good agreement with King's analytical treatment of this problem.     

焊接接头局部塑性行为的循环压痕实验研究

基于纳米压痕技术,对转子钢焊接接头不同区域（母材、焊缝和热影响区）开展了压入位移控制的单向压痕实验和压入载荷控制的循环压痕实验研究．首先,通过压入位移控制的单向压痕实验,采用多次测试取平均值的方式获得了焊接接头各个区域的弹性模量和硬度分布特征,同时对各区域弹性模量中值点的载荷-压入深度曲线进行了分析;其次,对各个区域进行压入载荷控制的循环压痕实验,比较其压入深度随循环周次的演化特征．结果表明,焊接接头不同区域力学性能差异较大,热影响区的弹性模量、硬度、抗拉强度和抗循环变形能力最高,焊缝次之,母材最弱;三个区域在循环压痕载荷下的接触载荷-压入深度滞回环曲线均表现出类似棘轮变形的演化特征,且母材演化速度高于焊缝,高于热影响区．研究结果对汽轮机焊接转子的焊接工艺的优化、寿命预测和可靠性设计具有重要的借鉴意义．     

Nano-Indentation Hardness and Strain Hardening of Silicon,Sodium Chloride and Tungsten Crystals

Background

A previous review of micro- and nano-indentation hardness tests and their analyses gave emphasis to obtaining measurements of continuous nano-indentation load, P, versus, depth, h, recordings that monitor the full elastic–plastic deformation behavior of a localized crystal volume [1].

Objective

Attention is given to determining the complete, indentation-based, elastic–plastic deformation properties of the local volume, including the initial crystal elastic deformation behavior and, especially to evaluation of post pop-in plastic strain hardening.

Method

Stress–strain calculations are presented for an initial Hertzian elastic loading and follow-on crystal micro- and nano-scale plastic deformation responses [2].

Results

Applied load, P, dependencies on contact diameters, d_i, of silicon crystals are compiled on the basis of elastic, plastic and cracking predictions, giving indication at the lowest P values of an indentation size effect (ISE) for the crystal hardness. Elastic–plastic stress–strain curves are presented for sodium chloride and tungsten crystals. The hardness and strain hardening calculations also demonstrate an influence of the ISE.

Conclusions

The exceptional plastic strain hardening behaviors scale dimensionally with corresponding dislocation interactions and sessile reactions within the very localized plastic indentation zones. There is usefulness in determining elastic modulus values from the initial loading record. Micro- and nano-scale dislocation interactions/reactions account for the high stress and strain hardening levels as well as the occurrence of an ISE.

     

考虑塑性和刚度不匹配的焊接残余应力估算

现有残余应力计算方法未能考虑材料塑性变形和焊接接头刚度不匹配的影响,使得焊接残余应力计算结果和实际残余应力存在较大偏差.在2219-T87铝合金钨极氩弧焊焊接头残余应力测试基础上,提出一种基于非线性有限元和材料弹性模量分区的残余应力—释放应变曲线的残余应力计算方法,研究了材料塑性变形和接头刚度不匹配对焊接残余应力计算的影响.结果表明,焊接接头中非均质材料塑性不匹配可以引起对于残余应力计算的较大误差;材料塑性变形对残余应力的影响大于接头刚度不匹配对残余应力的影响.所提出方法修正了传统方法在焊接接头的残余应力计算中由于未考虑接头非均质材料塑性不匹配而引起的误差.     

二维材料力学行为的压痕测试

准确了解二维材料的力学性能对于推动其应用具有重要意义, 无基底压痕技术是目前最广泛采用的二维材料力学性能测试方法之一, 本文综述了二维材料压痕研究的最新进展以及所面临的问题, 并对将来的研究工作进行了展望.无基底压痕技术是将二维材料转移到带有沟槽或柱形孔的基底上, 制备二维材料"梁"和"鼓"模型, 然后利用原子力显微镜测量其在压针作用下的载荷--位移关系, 最后通过基于连续介质薄膜导出的压痕响应分析模型拟合实验结果, 估算出二维材料的弹性模量和本征强度.由于二维材料的厚度远小于连续介质薄膜, 来自于压头以及基底孔侧壁的范德华力对二维材料的压痕响应具有显著影响, 造成二维材料与传统压痕分析模型中的基本假设不符, 导致不能准确预测二维材料的弹性模量; 另外, 由于传统压痕模型无法准确描述二维材料在大变形下的非线性行为, 以及由缺陷等引起的应力集中, 导致由压痕测试表征的二维材料(特别是多晶二维材料)本征强度具有较大的偏差. 因此, 一方面需要正确了解由压痕技术获得的二维材料力学性能, 另一方面还需对目前的研究方法做进一步的改进和完善.      

Indentation tests investigation of mechanical behavior of two-dimensional materials

准确了解二维材料的力学性能对于推动其应用具有重要意义, 无基底压痕技术是目前最广泛采用的二维材料力学性能测试方法之一, 本文综述了二维材料压痕研究的最新进展以及所面临的问题, 并对将来的研究工作进行了展望.无基底压痕技术是将二维材料转移到带有沟槽或柱形孔的基底上, 制备二维材料"梁"和"鼓"模型, 然后利用原子力显微镜测量其在压针作用下的载荷--位移关系, 最后通过基于连续介质薄膜导出的压痕响应分析模型拟合实验结果, 估算出二维材料的弹性模量和本征强度.由于二维材料的厚度远小于连续介质薄膜, 来自于压头以及基底孔侧壁的范德华力对二维材料的压痕响应具有显著影响, 造成二维材料与传统压痕分析模型中的基本假设不符, 导致不能准确预测二维材料的弹性模量; 另外, 由于传统压痕模型无法准确描述二维材料在大变形下的非线性行为, 以及由缺陷等引起的应力集中, 导致由压痕测试表征的二维材料(特别是多晶二维材料)本征强度具有较大的偏差. 因此, 一方面需要正确了解由压痕技术获得的二维材料力学性能, 另一方面还需对目前的研究方法做进一步的改进和完善.     

核壳结构PS/CeO2复合微球弹性模量的AFM测定

利用原子力显微镜测定了聚苯乙烯(Polystyrene, PS)微球和核壳结构PS/CeO₂复合微球的力-位移曲线,并根据Hertz接触理论计算了微球样品的弹性模量.结果表明:粒径在120 nm左右的PS微球的平均弹性模量约为2.80 GPa,其数值略低于聚苯乙烯块体材料的弹性模量.复合微球的弹性模量随CeO₂壳层厚度的增加而增大,当CeO₂壳厚分别约为8、12和16 nm时,其平均弹性模量依次约为7.93、8.25和10.67 GPa.与纯氧化铈相比,PS/CeO₂复合微球的弹性模量更接近于聚苯乙烯微球.     

Mechanics of indentation of plastically graded materials—I: Analysis

The introduction of controlled gradients in plastic properties is known to influence the resistance to damage and cracking at contact surfaces in many tribological applications. In order to assess potentially beneficial effects of plastic property gradients in tribological applications, it is essential first to develop a comprehensive and quantitative understanding of the effects of yield strength and strain hardening exponent on contact deformation under the most fundamental contact condition: normal indentation. To date, however, systematic and quantitative studies of plasticity gradient effects on indentation response have not been completed. A comprehensive parametric study of the mechanics of normal indentation of plastically graded materials was therefore undertaken in this work by recourse to finite element method (FEM) computations. On the basis of a large number of computational simulations, a general methodology for assessing instrumented indentation response of plastically graded materials is formulated so that quantitative interpretations of depth-sensing indentation experiments could be performed. The specific case of linear variation in yield strength with depth below the indented surface is explored in detail. Universal dimensionless functions are extracted from FEM simulations so as to predict the indentation load versus depth of penetration curves for a wide variety of plastically graded engineering metals and alloys for interpretation of, and comparisons with, experimental results. Furthermore, the effect of plasticity gradient on the residual indentation pile-up profile is systematically studied. The computations reveal that pile-up of the graded alloy around the indenter, for indentation with increasing yield strength beneath the surface, is noticeably higher than that for the two homogeneous reference materials that constitute the bounding conditions for the graded material. Pile-up is also found to be an increasing function of yield strength gradient and a decreasing function of frictional coefficient. The stress and plastic strain distributions under the indenter tip with and without plasticity gradient are also examined to rationalize the predicted trends. In Part II of this paper, we compare the predictions of depth-sensing indentation and pile-up response with experiments on a specially made, graded model Ni-W alloy with controlled gradients in nanocrystalline grain size.     

Modeling elasto-plastic indentation on layered materials using the equivalent inclusion method

This paper develops a fast semi-analytical model for solving the three-dimensional elasto-plastic contact problems involving layered materials using the Equivalent Inclusion Method (EIM). The analytical elastic solutions of a half-space subjected to a unit surface pressure and a unit subsurface eigenstrain are employed in this model; the topmost layer is simulated by an equivalent inclusion with fictitious eigenstrain. Accumulative plastic deformation is determined by a procedure involving an iterative plasticity loop and an incremental loading process. Algorithms of the fast Fourier transform (FFT) and the Conjugate Gradient Method (CGM) are utilized to improve the computation efficiency. An analytical elastic solution of layered body contact (O’Sullivan and King, 1988) and an indentation experiment result involving a layered substrate (Michler et al., 1999) are used to examine the accuracy of this model. Comparisons between numerical results from the present model and a commercial FEM software (Abaqus) are also presented. Case studies of a rigid ball loaded against a layered elasto-plastic half-space are conducted to explore the effects of the modulus, yield strength, and thickness of the coating on the hardness, stiffness, and plastic deformation of the composite body.     

Determining the Elastic Modulus of Compliant Thin Films Supported on Substrates from Flat Punch Indentation Measurements

Instrumented indentation is a technique that can be used to measure the elastic properties of soft thin films supported on stiffer substrates, including polymer films, cellulosic sheets, and thin layers of biological materials. When measuring thin film properties using indentation, the effect of the substrate must be considered. Most existing models for determining the properties of thin films from indentation measurements were developed for metal and dielectric films bonded to semiconductor substrates and have been applied to systems with film-substrate modulus ratios between 0.1 and 10. In the present work, flat punch indentation of a thin film either bonded to or in contact with a substrate is examined using finite element modeling. A broad range of film-substrate modulus ratios from 0.0001 to 1 are investigated. As the substrate is effectively rigid compared to the film when the film-substrate modulus ratio is less than 0.0001, the results are also useful for understanding systems with lower film-substrate modulus ratios. The effects of the contact radius, film thickness, elastic properties, and friction between the film and the substrate on the measured stiffness were quantified using finite element modeling in order to understand how the elastic properties of the film can be extracted from indentation measurements. A semi-analytical model was developed to describe the finite element modeling results and facilitate the use of the results to analyze experimental measurements. The model was validated through analysis of indentation measurements of thin polyethylene sheets that were supported on substrates of various stiffness.     

金属材料的强度与应力-应变关系的球压入测试方法

压入法获取材料单轴应力-应变关系和抗拉强度对服役结构完整性评价有重要的基础意义.假定材料均匀连续、各向同性、应力应变关系符合Hollomon律,基于能量等效假定,即代表性体积单元(representativevolume element, RVE)的vonMises等效和有效变形域内能量中值等效假定,本文提出了关联材料载荷、深度、球压头直径和Hollomon律的四参数半解析球压入(semi-analyticalspherical indentation,SSI)模型.通过球压入载荷-深度试验关系获得材料的应力-应变关系和抗拉强度.考虑压入过程中的损伤效应,针对金属材料提出了用于球压入测试的材料弹性模量修正模型.对11种延性金属材料完成了球压入试验,采用本文提出的球压入试验方法测到的弹性模量、应力-应变关系和抗拉强度与单轴拉伸试验结果吻合良好.      

Sample boundary effect in nanoindentation of nano and microscale surface structures

Nanoindentation is a widely used technique to characterize mechanical properties of materials in small volumes. When the sample size is comparable to the indent size, the indentation-induced plastic zone can be affected by the sample boundary which may cause inaccurate interpretation of the mechanical properties. In this study, the sample boundary effect is investigated by performing experiments and atomistic simulations of nanoindentation into nano- and micro-scale Au pillars and bulk Au (0 0 1) surfaces. In experiments, a more compliant deformation is observed in pillar indentations compared to bulk Au. The elastic modulus decreases with increasing indent size over sample size ratio. Atomistic simulations are performed to gain insights on the mechanisms of pillar deformation and pillar boundary effect. The reduced modulus has a similar trend of decrease with increasing indent size over sample size ratio. Significantly different dislocation activities and dislocation interactions with the pillar boundary contribute to the lower value of the reduced modulus in the pillar indentation. The presence of the free surface would allow the dislocations to annihilate, causing a higher plastic recovery during the pillar unloading process.