Evaluation of rheological properties and swelling behaviour of sonicated scleroglucan samples

Scleroglucan is a natural polysaccharide that has been proposed for various applications. However there is no investigation on its property variations when the molecular weight of this polymer is reduced. Scleroglucan was sonicated at two different polymer concentrations for different periods of time and the effect of sonication was investigated with respect to molecular weight variations and rheological properties. Molar mass, estimated by viscometric measurements, was drastically reduced already after a sonication for a few min. Sonicated samples were used for the preparation of gels in the presence of borate ions. The effect of borax on the new samples was investigated by recording the mechanical spectra and the flow curves. A comparison with the system prepared with the dialysed polymer was also carried out. The anisotropic elongation, observed with tablets of scleroglucan and borax, was remarkably reduced when the sonicated samples were used for the preparation of the gels.     

Theoretical and experimental study on a self-assembling polysaccharide forming nanochannels: static and dynamic effects induced by a soft confinement

It is well-known that the polysaccharide scleroglucan (Sclg) exhibits a triple-helix conformation (triplex) and it is able to form hydrogels in water solution. Furthermore, these hydrogels are influenced by the presence of borax, in terms of rheological and drug release properties. In previous works, we showed that the presence of borax stabilizes the intertriplex interactions and that the property variations, induced by borax, can be fully explained, considering that the Sclg triplexes can form nanochannel-like structures. In this paper, the stability of these aggregates has been experimentally studied by means of atomic force microscopy (AFM) and theoretically investigated by means of molecular dynamics (MD) simulations. The simulations indicate that the borax stabilizes nanochannel-like structures when seven triplexes are considered. The simultaneous presence of different Sclg triplexes in a narrow space strongly influences the properties of confined water molecules in a way similar, in many aspects, to that of water molecules located in the inner part of well-defined nanochannels (e.g., diffusion inside carbon nanotubes). As a consequence, also the conformational properties of flanking regions of Sclg triplexes are influenced. Furthermore, differential scanning calorimetry (DSC) data show that the well-known conformational transition occurring at 280 K for Sclg does not take place in the presence of borax. The MD simulations suggest that such lack of transition is a direct consequence of the presence of borax. The role of Na+ counterions in the hydrogel structure is also investigated.     

Optical vs. direct sorption and swelling measurements for the study of stiff-chain polymer-penetrant interactions

This work involves interferometric ‘optical thickness’ and refractive index measurements performed in an optical thickness meter (OTM), on supported cellulose acetate (CA) films equilibrated with various activities of methylene chloride (MC) vapor. The relevant equilibrium sorption and volume swelling isotherms were determined by application of the Claussius-Mossotti equation on the assumption that these films swell unidimensionally along the thickness direction, and were compared with corresponding direct equilibrium sorption (weight gain), elongation and thickness dilation measurements on similar free films performed in a vacuum sorption/swelling apparatus (VSA) and complemented with refractive index data. Combined elongation and thickness dilation data from the VSA showed that free glass-cast CA films exhibit pronounced swelling anisotropy. The said anisotropy, although it cannot be completely eliminated, by conditioning at high degrees of swelling, does not appear to affect the extent of volume swelling significantly, thus permitting quantitative comparison of sorption and swelling isotherms determined by the VSA and the OTM. Such comparison showed satisfactory agreement between these two sets of results up to an MC uptake of ca. 0.4 gMC/cm³ of dry CA corresponding to a degree of swelling of ca. 0.2. Increasing discrepancies are observed at higher MC concentrations, which are attributable to breakdown of the assumption used that the supported films swell unidimensionally along the thickness direction. The present CA-MC volume swelling data exhibit the negative deviation from volume additivity on mixing typical glassy polymers.     

Effects of concentration of nonionic surfactant and molecular weight of polymers on the morphology of anisotropic polystyrene/poly(methyl methacrylate) composite particles prepared by solvent evaporation method

The effects of the concentration of polyoxyethylene octylphenyl ether (OP-10) as a nonionic surfactant and the molecular weight of polymers (polystyrene (PS) and poly(methyl methacrylate) (PMMA)) on the morphology of anisotropic PS/PMMA composite particles were investigated. In the case of polymers with lower molecular weight (M _w ≈ 6.0 × 10⁴ g/mol), the PS/PMMA composite particles have dimple, via acorn, to hemispherical shapes along with the increase of the OP-10 concentration. On the other hand, when the polymers have higher molecular weight (M _w ≈ 3.3 × 10⁵ g/mol), the morphology of PS/PMMA composite particles changed from dimple, via hemispherical, to snowman-like structure while the concentration of OP-10 was increased. Furthermore, thermodynamic analysis was first simply made by spreading coefficients, and the results indicated that both the concentration of OP-10 aqueous solution and the molecular weight of polymers were very important to the final morphology of anisotropic composite particles.     

Effect of High Pressure on the Polymorphs of Paracetamol

Effect of hydrostatic pressure on the two (I – monoclinic and II – orthorhombic) polymorphs of paracetamol was studied by X-ray diffraction in the diamond anvil cell at pressures up to 4.5 GPa (for the monoclinic form) and up to 5.5 GPa (for the orthorhombic form). The two groups of phenomena were studied: (i) the anisotropic structural distortion of the same polymorph, (ii) transitions between the polymorphs induced by pressure. The anisotropy of structural distortion of polymorphs I and II was well reproducible from sample to sample, also from powder samples to single crystals. The bulk compressibility of the two forms was shown to be practically the same. However, a noticeable qualitative difference in the anisotropy of structural distortion was observed: with increasing pressure the structure of polymorph II contracted in all the directions showing isotropic compression in the planes of hydrogen-bonded molecular layers, whereas the layers in the structure of the polymorph I expanded in some directions. Maximum compression in both polymorphs I and II was observed in the directions normal to the molecular layers. The transitions between the polymorphs induced by pressure were poorly reproducible and depended strongly on the sample and on the procedure of increasing/decreasing pressure. No phase transitions were induced in the single crystals of the monoclinic polymorph at pressures at least up to 4GPa, although a partial transformation of polymorph I into polymorph II was observed at increased pressure in powder samples. Polymorph II transformed partly into the polymorph I during grinding. The transformation could be hindered if grinding was carried out in CCl₄. This revised version was published online in August 2006 with corrections to the Cover Date.     

Selenomethionine‐Catalyzed Nickel Ion Reduction at a Mercury Electrode: Applications in the Analysis of Nutritional Supplements

Selenomethionine (SeMet) is a catalyst for Ni²⁺ reduction at a mercury electrode in a borax buffer at pH around 9 and gives rise to a differential pulse voltammetric peak, A, at ?0.74 V vs. the Ag|AgCl, (3 M KCl) reference electrode. Peak current is directly proportional to SeMet concentration over the concentration range 0.4–10 μM. Alkali and alkali‐earth ions depress to some extent the sensitivity but the current‐concentration relationships remains linear even under these conditions. Differential pulse cathodic stripping voltammetry (DPCSV) in 0.01 M borax results in two partially overlapped peaks. The more negative (A, at about ?0.74 V) is similar to that recorded with no deposition and is due to the catalysis by nonadsorbed SeMet, whereas the more positive one (B, at about ?0.60 V) results from the catalysis by adsorbed SeMet. Only the DPCSV peak A appears if 0.1 M KNO₃ is also present along with 0.01 M borax. Stearic acid, which is present in nutritional supplement tablets, improves the separation of the DPCSV peaks. Consequently, the peak B recorded with 0.01 M borax buffer allows determining SeMet in nutritional supplement tablets by the standard addition method and enables discriminating between the organic and inorganic selenium forms.     

Gold nanoparticle mediated formation of aligned nanotube composite films

We report on the formation of highly anisotropic nanotube composite materials, made by the attachment of gold nanoparticles to the surface of the single-walled carbon nanotubes, followed by preparation of an aligned composite film by compression in a Langmuir-Blodgett trough. The gold is attached in a one-step sonication procedure. The gold-modified nanotube material forms a stable suspension in toluene and has been characterized by atomic force and scanning force microscopy, energy-dispersive X-ray spectroscopy, and Raman spectroscopy. The aligned films have highly anisotropic electrical properties, with a factor of approximately 3000 difference in the conductivity between the aligned and perpendicular directions.     

Frontal photopolymerization synthesis of multilayer hydrogels with high mechanical strength

Multilayer hydrogels were prepared by frontal photopolymerization of acrylamide and 2-acrylamido-2-methylpropane sulfonic acid using hydrophilic reactive microgels (HRM) as crosslinkers instead of conventional crosslinkers. The hydrophilic microgels (HM) were prepared by inverse emulsion photopolymerization and then were chemical modified by N-methylolacrylamide (NMA) to obtain HRM with CC double bonds. The HM and HRM was characterized by dynamic light scattering measurements, SEM, TEM and FTIR, respectively. It was found that the resulting multilayer hydrogels showed high fracture strength and high tensile elongation along parallel direction. However their fracture strength and tensile elongation along perpendicular direction was very weak. The swollen multilayer hydrogels were about 1.0–2.0 mm in thickness, the maximal equilibrium swelling degree was only 30.45. The multilayer hydrogels were characterized by DSC, TEM and XRD, respectively. The swelling property and mechanical strength of some typical multilayer hydrogels were studied.     

Anisotropic plasticity and chain orientation in polymer glasses

The anisotropic mechanical response of oriented polymer glasses is studied through simulations with a coarse-grained model. Systems are first oriented by uniaxial compression or tension along an axis. Then the mechanical response to subsequent deformation along the same axis or along a perpendicular axis is measured. As in experiments, the flow stress and strain hardening modulus are both larger when deformation increases the degree of molecular orientation produced by prestrain, and smaller when deformation reduces the degree of orientation. All stress curves for parallel prestrains collapse when plotted against either the total integrated strain or the degree of molecular orientation. Stress curves for perpendicular prestrains can also be collapsed. The stress depends on the degree of strain or molecular orientation along the final deformation axis and is independent of the degree of orientation in the perpendicular plane. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1473–1482, 2010     

Sliding charge-density wave conductivity in potassium molybdenum bronze

The monoclinic blue-bronze, K_0.30MoO₃, is an anisotropic metal that undergoes a charge density wave (CDW)-driven phase transition at 180 K, below which nonlinear current-voltage characteristics are observed. In this paper, we examine the anisotropy of the electric and magnetic properties of K_0.30MoO₃ and their relationship to observed CDW phenomena. We show that the conductivity is highest along the monoclinic b axis and 10 and 100 times lower in two directions perpendicular to b (in the ($\text{2}\text{0 1}$ plane and perpendicular to these planes, respectively). In the CDW state, the conductivity along the b axis is nonlinear when the applied electric field exceeds a small threshold on the order of 50 mV/cm, but is field-independent in perpendicular directions. A periodic response to a dc bias was observed in one small K_0.30MoO₃ sample, however, the observation of an NbSe₃-like response in K_0.30MoO₃ may depend on sample size or the quality of the electrical contacts to the sample.     

Liquid crystalline cellulose derivative elastomer films under uniaxial strain

Mesogenic cellulose derivative chains cross-linked into free-standing thin films were prepared by a shear-casting technique from anisotropic precursor solutions of thermotropic (acetoxypropyl)cellulose. After shear cessation a macroscopically oriented serpentine structure with the director in average along the shear direction is locked resulting in anisotropic optical and mechanical properties of the material. These films were submitted to an external uniaxial mechanical field perpendicular and parallel to the shear direction. Stretching perpendicular to the shear direction produced significant director rotations and a reset of order of the director order parameter for a deformation in the range 2–3 as detected by X-rays and optical microscopy. The different response found for strains imposed parallel and perpendicular to the initial average director orientation indicates that even though our system shows a serpentine director modulation that is either attenuated or reinforced by deformations parallel or perpendicular to the shear direction, its behaviour is similar to theoretical predictions for monodomain nematic elastomers described in the literature.     

Synthesis and characterization of new cross-linked terpolymer systems containing silyl group

A series of acrylic terpolymers containing silyl pendant groups was prepared by free radical cross-linking copolymerization. Me₃Si, Et₃Si and t-BuMe₂Si together with cubane-1, 4-dicarboxylic acid (CDA) were covalently linked with 2-hydroxyethyl methacrylate (HEMA). The silyl-linked HEMA are abbreviated as TMSiEMA, TESiEMA and TBSiEMA respectively. Cubane-1, 4-dicarboxylic acid (CDA) linked to two HEMA group is the cross-linking agent (CA). Free radical cross-linking terpolymerization of the methyl methacrylate (MMA) and methacrylic acid (MAA) with two different molar ratios of organosilyl monomers and CA was carried out at 60–70 ^∘C. The compositions of the cross-linked three-dimensional polymers were determined by FT-IR spectroscopy. The glass transition temperature (Tg) of the network polymers was determined calorimetrically. The Tg of network terpolymers increases with increasing of cross-linking degree. Equilibrium swelling studies were carried out in enzyme-free simulated gastric and intestinal fluids (SGF and SIF, respectively). The gels swelled more in SIF than in SGF. The swelling behaviour of the copolymers was dependent on the content of MAA groups and caused a decrease in gel swelling in pH 1 or an increase in gel swelling in pH 7.4. Based on the great difference in swelling ratio at pH 1 and 7.4 for P-1, P-6 and P-10 appear to be good candidates for colon-specific drug delivery.     

Characterization by mirage effect technique of dye diffusion in columnar discotic liquid crystals

The anisotropic behaviour of the matter diffusion in columnar discotic liquid crystals is studied by the 'mirage effect' technique. The D_h and D₀ mesophases of C₈HET and C₁₁HET, respectively, are considered. The impurity (a dye, the 1-[4-(xylylazo)xylylazo]-2-naphthol) diffusing in these mesophases is detected by the photothermal deflection technique. Measurements of the diffusion coefficients are performed in two perpendicular directions, along and perpendicularly to the molecular columns. Effects of impurity size, length and type of the branched chains on the discs of triphenylene, and molecule stackings in columns, are presented.     

Anisotropic swelling behavior of copolymeric gel film with crystalline oriented side chains

A copolymeric gel film with swelling anisotropy was prepared on a flat Petri dish by free-radical copolymerization of stearyl acrylate (SA) and acrylic acid (AA) with N,N′-methylenebisacrylamide (MBAA) as the crosslinking agent. An X-ray diffraction study of the gel film revealed that the SA side chains in the gel film SA/AA/MBAA:24.7/74.3/1.0 (in mol) were spontaneously oriented perpendicular to the film surface in order to minimize the interfacial free energy between the gel film surface and air. The one-dimensional swelling ratio perpendicular to the gel film surface in an ethanol/water mixture was greater than that in the direction parallel to the film surface. This swelling anisotropy can be explained on the basis of changes in the state of anisotropic aggregation.     

Molecular orientation and liquid crystal alignment properties of new cinnamate-based photocrosslinkable polymers

Isotropic thin films of three original phenyl substituted cinnamate-based polymers, here-after referred to as 'Para', 'Meta' and 'Metamet' have been exposed to linearly polarized UV light and their photoinduced molecular orientations have been studied. The resulting photocrosslinked anisotropic polymer films were characterized using UV, conventional and polarization modulation (PM) FTIR spectroscopies. From UV and PM-IR linear dichroism measurements, at least two simultaneous orientation processes appear to play a key role in these phenyl substituted cinnamate-based systems. On the one hand, isomerization reactions deplete chromophores along the polarization direction (P) of the UV light and induce a preferential orientation of remaining 'trans'-isomers perpendicular to P; on the other hand, cycloaddition reactions lead to the formation of either head to head or head to tail photodimers aligned preferentially along P in the 'Para' and to a lesser extent in the 'Meta' and 'Metamet' systems. These last results are related to the different liquid crystal alignment properties of the films, and the influences of the chemical structure of the chromophores are discussed.     

Mass and momentum transfer in polymers. III. Effects of liquid penetrants on tensile stress relaxation of amorphous polymers

Sorption, diffusion, swelling, and tensile stress relaxation measurements were made at room temperature (23°C) for the systems poly(n-butyl methacrylate) (PBMA) with liquid methanol and ethanol, and poly(methyl acrylate) (PMA) with liquid water. Stress relaxation curves for the fully swollen polymers could be superimposed approximately with those for the dry polymers by appropriate shifting along the long axes. For PMA–water the measured curve for stress relaxation with concurrent sorption could be predicted accurately by using a moving boundary theory with data measurements of stress relaxation of the unswollen and swollen polymer combined with sorption data. The modified moving boundary theory is generalized to include the effects of dimension changes through swelling and the larger effects of plasticization associated with sorption of liquids. This improved theory accurately predicts measured curves of stress relaxation with concurrent sorption for the PBMA–alcohol systems from individual stress relaxation, sorption, diffusion and swelling data. The general approach should be applicable to other amorphous polymer–liquid swelling agent systems. The anisotropic nature of swelling of polymer films and its effect on calculated diffusion coefficients are discussed briefly.     

Reentrant behavior of poly(vinyl alcohol)–borax semidilute aqueous solutions

 The reentrant behavior of Poly(vinyl alcohol) (PVA)–borax aqueous semidilute solutions with a PVA concentration of 20 g/l and borax concentrations varies from 0.0 to 0.20 M was investigated using dynamic light scattering (DLS) and dynamic viscoelastic measurements. Two (fast and slow modes) and three (fast, middle, and slow) relaxation modes of PVA semidilute aqueous solutions without and with the presence of borax, respectively, were observed from DLS measurements. The fast and middle relaxation modes were q ²-dependent (q is the scattering vector) characteristic of diffusive behavior; however, the slow modes were q ³-dependent, characteristic of intraparticle dynamics. The experimental results showed that the slow relaxation mode dominates the DLS relaxation. The DLS slow mode relaxation time, τ_s, and the viscoelastic modulus G′(ω) and G′′(ω) data had a similar trend and demonstrated reentrant behavior as the borax concentration was increased from 0.0 to 0.20 M, i.e. τ_s, G′(ω), and G′′(ω) fluctuated with increasing borax concentration. The excluded-volume effect of polymers, charge repulsion among borate ions bound on PVA molecules, and intermolecular cross-linking didiol–borate complexation caused an expansion of the polymer chain; however, the screening effect of free Na⁺ ions on the negative charge of the borate ions bound on PVA and intramolecular cross-linking didiol–borate complexation led to a shrinkage of the polymer chain. The reentrant behavior was the consequence of the balance between expansion and shrinkage of the PVA–borate complex. Received: 26 March 1999/Accepted in revised form: 3 September 1999     

Controlled release from directly compressible theophylline buccal tablets

The aim of the current study was the development of theophylline buccal adhesive tablets using direct compression. Buccal adhesive formulations were developed using a water soluble resin with various combinations of mucoadhesive polymers. The prepared theophylline tablets were evaluated for tensile strength, swelling capacity and ex vivo mucoadhesion performance. Ex vivo mucoadhesion was assessed using porcine gingival tissue and the peak detachment forces were found to be suitable for a buccal adhesive tablet with a maximum of 1.5 N approximately. The effect of formulation composition on the release pattern was also investigated. Most formulations showed theophylline controlled release profiles depended on the grade and polymer ratio. The release mechanisms were found to fit Peppas’ kinetic model over a period of 5 h. In general the majority of the developed formulations presented suitable adhesion and controlled drug release.     

Molecular dynamics study of the liquid-vapor interface of acetonitrile: equilibrium and dynamical properties

The equilibrium and dynamical properties of the liquid-vapor interface of pure acetonitrile are studied by means of molecular dynamics simulations. Both nonpolarizable and polarizable models are employed in the present study. For the nonpolarizable model, the simulations are carried out for two different system sizes and at two different temperatures whereas the simulation with the polarizable model is done for a single system. The inhomogeneous density, anisotropic orientational profile, the width of the interface, and also the surface tension are calculated at room temperature and also at a lower temperature of 273 K. The dynamical aspects of the interface are investigated in terms of the single-particle dynamical properties such as the relaxation of velocity autocorrelation and the translational diffusion coefficients along the perpendicular and parallel directions and the dipole orientational relaxation of the interfacial acetonitrile molecules. The results of the interfacial dynamics are compared with those of the corresponding bulk phases at both temperatures. The convergence of the calculated results with respect to the length of simulation runs and the system size are also discussed.     

Anisotropic Conductivity at the Single‐Molecule Scale

In most junctions built by wiring a single molecule between two electrodes, the electrons flow along only one axis: between the two anchoring groups. However, molecules can be anisotropic, and an orientation‐dependent conductance is expected. Here, we fabricated single‐molecule junctions by using the electrode potential to control the molecular orientation and access individual elements of the conductivity tensor. We measured the conductance in two directions, along the molecular plane as the benzene ring bridges two electrodes using anchoring groups (upright) and orthogonal to the molecular plane with the molecule lying flat on the substrate (planar). The perpendicular (planar) conductance is about 400 times higher than that along the molecular plane (upright). This offers a new method for designing a reversible room‐temperature single‐molecule electromechanical switch that controllably employs the electrode potential to orient the molecule in the junction in either “ON” or “OFF” conductance states.