Harmful azo colorants in leather. Determination based on their cleavage and extraction of corresponding carcinogenic aromatic amines using modern extraction techniques

This study concerns the possibilities of using microwave-assisted extraction (MAE) or supercritical fluid extraction (SFE) for detection of harmful azo colorants in leather. After degreasing of the leather sample with SFE there follows a reductive cleavage of the azo colorants to their corresponding aromatic amines in the MAE or SFE equipment. The aromatic amines are subsequently extracted using either MAE or SFE and then finally determined by liquid chromatography with diode-array detection. The results have been compared with recoveries obtained using the German DIN method 53316. This standard method, based on conventional solvent extraction, is used in several European countries. Overall much better recoveries were obtained using MAE or SFE. With both MAE and SFE the amine recoveries of spiked leather samples were generally above 50%. The average recoveries were 62% for MAE and 60% for SFE (solvent collection) compared to 24% with the DIN method. For genuine leather samples the recoveries decreased, especially for benzidine. In this case the average values for MAE, SFE and DIN were 54, 38 and 19%, respectively. The quantification limits in leather samples using MAE or SFE were below 1 mg/kg for all amines investigated. The within-laboratory precision was generally better than 10%, varying somewhat with the analyte considered. With the proposed methodology, the amount of hazardous organic solvents used could be decreased and the sample throughput increased with at least a factor of two with less manual handling compared to the DIN method.     

Trace analysis of trichlorobenzenes in fish by microwave-assisted extraction and gas chromatography-electron-capture detection

An analytical method consisting of extraction, clean-up, and analysis by gas chromatography-electron-capture detection (GC-ECD) was developed for the determination of trichlorobenzenes (TCBs) in fish samples. Two extraction methods, saponification and liquid-liquid extraction (S-LLE), and microwave-assisted extraction (MAE), were evaluated. In both cases, n-pentane was used as the extraction solvent. For S-LLE, the recoveries ranged from 66.6+/-9.1% for 1-bromo-4-chlorobenzene (4-BCB) to 93.5+/-4.9% for 1,2,4-trichlorobenzene (1,2,4-TCB). The recoveries were significantly lower, between 31.0+/-3.9% for 1,2,3-trichlorobenzene (1,2,3-TCB) and 52.3+/-3.0% for 1,3,5-trichlorobenzene (1,3,5-TCB), in the absence of fish. Proteins and glycerides of the fish tissue seemed to compete with TCBs for the base, and hence decreased their decomposition rate. In the case of MAE, the recoveries were highly dependent on the pressure applied during extraction. At 5 bar, much higher recoveries were obtained, from 66.7+/-15.6% for 4-BCB to 79.9+/-13.6% for 1,2,4-TCB, than at 1 bar. Sulfur formation was, however, observed at 5 bar, and interfered with the GC-ECD analysis of TCBs. Sulfur was adequately removed by copper powder treatment, which was shown not to affect the recovery of analytes. The recoveries of target analytes by S-LLE and MAE did not differ statistically (t-test, alpha = 0.01). Both methods were appropriate for the detection of TCBs at concentration levels typically observed in marine biota, i.e. approximately 1 ng/g. S-LLE was, however, more time consuming, and required larger volumes of high-purity organic solvents than MAE.     

Considerations for analytical supercritical fluid extraction of sulfonyl ureas employing a modified fluid

Important considerations are discussed for analytical SFE method development employing methanol–modified carbon dioxide and solid-phase trapping. The focus of this study was to break the method development procedure into distinct steps so that the origins of low recoveries could be determined conclusively. Sulfonyl urea herbicides were used as probe analytes. Analyte solubility, analyte trapping, analyte trap removal (solid-phase), and extract analysis were all shown to be equally important in achieving quantitative SFE recoveries.     

Theoretical optimization of analyte collection in analytical supercritical fluid extraction

Summary Optimizing the extracted analyte collection step in analytical supercritical fluid extraction (SFE) is of key importance in achieving high analyte recoveries and extraction efficiencies. Whereas the extraction step in SFE has been well characterized both theoretically and experimentally; the analyte collection step after SFE has few theoretical guidelines, aside from a few empirical studies which have appeared in the literature. In this study, we have applied several theoretical approaches using experimental data to optimize analyte trapping efficiency in SFE. A vapour-liquid equilibrium model has been formulated to predict the trapping efficiency for extracted solute collection in a open collection vessel. Secondly, a simple solution thermodynamic model for predicting solute (analyte) activity coefficients in various trapping solvents has been shown to have utility in predicting collection efficiencies. Finally, effective trapping efficiency after SFE using sorbent media is related to the extent of analyte breakthrough on the sorbent-filled trap after depressurization of supercritical fluid. Using experimental data determined via physico-chemical gas chromatographic measurements (i. e., specific retention volumes), we have shown the relationship between analyte breakthrough volume off of the trapping sorbent and volume of depressurized fluid through the collection trap. The above theoretical guidlines should prove of value to analysts in designing and optimizing the best conditions for trapping analytes after extraction via analytical SFE. Names are necessary to report factually on available data; however the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA implies no approval of the products to the exclusion of others that may also be suitable.     

Optimization of an analytical procedure for the determination of banned azo dyes in leather

The possibility of improving an existing method, based on supercritical-fluid extraction (SFE) and microwave-assisted extraction (MAE), for the determination of banned azo dyes in leather has been studied. Thus, optimization of experimental conditions in different steps (degreasing, reduction, and extraction) of the analytical procedure was performed. The influence of different variables (reaction time, temperature, and concentration of reducing agent) on the reduction process was evaluated by use of a factorial design. It was found that the concentration of the reducing agent and the interaction between time and temperature were the most influential variables. Consequently, by applying a higher temperature, the reaction time could be halved. The use of acidified water as extraction solvent in MAE was also investigated. Usually 1 mol L^–1 HCl was superior to methanol and buffer in terms of extraction efficiency. In conclusion, the present method gave significantly higher recoveries in comparison with the original method. All dyes were determined indirectly by measuring their corresponding harmful amines, formed after reduction by use of sodium dithionite.     

Microwave-assisted extraction of OCPs, PCBs and PAHs concentrated by semi-permeable membrane devices (SPMDs)

Microwave-assisted extraction (MAE) has been evaluated as an alternative to dialysis for extraction of some water-borne hydrophobic contaminants sampled by semi-permeable membrane devices (SPMDs). Seven organochlorine pesticides (OCPs), 11 polychlorinated biphenyls (PCBs) and 13 polycyclic aromatic hydrocarbons (PAHs) were accumulated in SPMDs at nanogram levels and extracted with three 3-min irradiation cycles with 33 mL of a solvent mixture hexane–water (10:1,v/v) in each cycle. The developed MAE method gave for all analytes investigated statistically comparable extraction yields with those found by dialysis carried out with a total volume of 250 mL hexane for 48 h at room temperature. The recoveries of all the targeted contaminants were in the range of 65–105% with variation coefficients not exceeding 19%. The applicability of the MAE extraction was tested in field SPMDs samples deployed for 15 days in a sewage-treatment process. Our results show that MAE provides a remarkable reduction of time and solvent volume when used as an extraction method in the analysis of SPMDs.     

Extraction of polycyclic aromatic nitrogen heterocycles from spiked soil samples

Extraction recovery of 10 selected polycyclic aromatic nitrogen heterocycles (PANHs), quinoline, 2-methylquinoline, 6-methylquinoline, 8-methylquinoline, acridine, benzo[h]quinoline, phenantridine, indole, 2-methylindole, and carbazole from spiked soil samples was tested. Four different extraction techniques, pressurized solvent extraction (PSE), supercritical fluid extraction (SFE), Soxhlet warm extraction (SOXW) and standard Soxhlet extraction (SOX), were applied and compared. The RP-HPLC technique with a silica-based octadecyl stationary phase was used for recovery determination of individual PANHs. Supercritical fluid extraction has been found to be the most effective method for the extraction of selected PANHs from soil. PSE and SOXW methods offered similar results with slightly lower extraction recoveries compared with SFE. On the contrary, SOX is a time-consuming method with a low recovery of target analytes and is not suitable for the extraction of PANHs from soils.     

Comparison of extraction techniques for the isolation of explosives and their degradation products from soil

A comparison of four extraction techniques used for the isolation of 14 explosive compounds (Method 8330-Explosives) from spiked soil samples is described. Soxhlet warm extraction (SWE), pressurized solvent extraction (PSE), microwave assisted extraction (MAE) and supercritical fluid extraction (SFE) were included. The effects of basic extraction conditions – i.e. type of extraction solvent, temperature, pressure, and extraction time – were investigated. The best extraction recovery of the monitored compounds from spiked soil was obtained using pressurized solvent extraction. Recoveries of explosives using the PSE technique were in the range from 65 to 112%. Extraction recoveries by Soxhlet warm extraction and supercritical fluid extraction reached 65–99% and 52–75%, respectively. The lowest extraction recoveries (28–65%) were obtained using microwave assisted extraction. A very low extraction recovery for tetryl was observed in all cases but the best results were achieved by pressurized solvent extraction (58%).     

Recent developments in sample preparation techniques for chromatography analysis of traditional Chinese medicines

Traditional Chinese medicines (TCMs) have a long history dating back thousands of years. Recently, there has been increasing interest worldwide in the use of TCMs for the prevention and treatment of various illnesses. In China, a large number of analytical tools, especially chromatographic techniques have been used to analyze the constituents of TCMs in order to control their quality and discover new bioactive compounds. In this paper, recent developments in sample preparation techniques for the extraction, clean-up, and concentration of analytes from TCMs are compared. These techniques include headspace solid-phase microextraction (HS-SPME), headspace liquid-phase microextraction (HS-LPME), microwave-assisted extraction (MAE), supercritical-fluid extraction (SFE), pressurized-liquid extraction (PLE), and microwave distillation (MD).     

Method development for the determination of wood preservatives in commercially treated wood using gas chromatography-mass spectrometry

Fungicides and insecticides are commonly used preservatives to protect wood products against microbiological degradations. Currently, there is a lack of analytical methods addressing the quantitative determination of a wide range of wood preserving species in wood matrices. In this study, a reliable method was developed for the determination of a mixture of wood preserving agents with differing chemical structures (i.e., properties), including tebuconazole (TAZ), propiconazole (PAZ), 3-iodo-2-propynyl butylcarbamate (IPBC), and permethrin (PER), in pine wood. The analyte recoveries obtained by Soxhlet and multiple-stage sonication extractions were compared. While both extraction methods yielded similar results (80–100%), Soxhlet extraction was found to be less labor-intensive and thus preferred providing also lower RSDs of 1–6%. In comparison to methanol, commonly used as an extraction solvent for triazoles, acetone yielded similar extraction efficiencies for all analytes while reducing the time of sample concentration. The solid phase extraction method for triazoles was adapted to allow for a separation of IPBC and PER from the wood matrix. As opposed to previous studies, three recovery standards were employed, which enabled the correction of individual analyte losses during the sample preparation. The matrix-affected limits of detection (LODs) using gas chromatography with mass spectrometric detection were nearly the same for triazoles 0.07 and 0.21 ng g⁻¹ for PAZ and TAZ in sapwood and 0.18 and 0.21 ng g⁻¹ in heartwood, respectively. Higher LODs were observed for IPBC and PER: 3.9 and 1.7 ng g⁻¹ in sapwood, and 2.0 and 6.0 ng g⁻¹ in heartwood, respectively. The recoveries in the wood submitted to commercial sample treatment showed gradient distribution of analytes depending on the penetration of the treatment.     

Comparaison de différentes méthodes d'extraction d'acides dicaféoylquiniques à partir d'une plante halophile

The aim of this study is the evaluation of different extraction methods for dicaffeoylquinic acids (diCQA), previously identified by a LC-DAD-ESI-QTOF dereplication strategy from a halophyte plant rich in polyphenols. Three different eco-friendly extraction methods are tested: microwave-assisted extraction (MAE), pressurized fluid extraction (PFE), supercritical fluid extraction (SFE). Various specific parameters are optimized for each of them. Global extraction yields are calculated for all extracts. Moreover, the extracts are analyzed by HPLC–DAD–ELSD, and the obtained profiles are compared to estimate qualitatively and semi-quantitatively their composition. The practicality of each technique is also discussed. The results show that the various parameters tested for PFE and MAE do not drastically affect the extraction of our interest compounds. However, the parameters tested on SFE are more decisive, such as the addition of a modifier in CO₂, which allows the extraction of diCQA.     

Rapid method for the determination of organochlorine pesticides and PCBs in fish muscle samples by microwave-assisted extraction and analysis of extracts by GC-ECD

A procedure for the multiresidue determination of organochlorine pesticides and polychlorinated biphenyls in fish muscle samples has been developed. The method is based on the microwave-assisted extraction (MAE) of food samples from an acetonitrile-water (95 + 5, v/v) mixture followed by SPE cleanup of the extracts and analysis by GC with an electron capture detector. MAE operational parameters, such as the extraction solvent, temperature, and time, were optimized with respect to the extraction efficiency of the target compounds from food samples with 10-13% fat content. The chosen extraction technique allows reduction of the solvent consumption and extraction time when compared with methods already used. Acetonitrile is a good extraction solvent for low-fat matrixes (2-20% fat content), such as fish samples, because it does not significantly dissolve the highly polar proteins, salts, and sugars commonly found in food and gives high recoveries of a wide polarity range of analytes. For purification, SPE using LC-Florisil was shown to be sufficient for the removal of coextracted substances. Recoveries > 78% with RSD values < 15% were obtained for all compounds under the selected conditions. Method quantification limits were in the 5-10 microg/kg range. The method was applied to the analysis of samples of herring (Clupea harengus) purchased at the local fish market. The method is rapid and reliable for the determination of organochlorine analytes in fish muscle.     

Comparison of extraction procedures for the determination of arsenic and other elements in lobster tissue by inductively coupled plasma mass spectrometry

A variety of extraction procedures were evaluated for the extraction of arsenic and other analytes from lobster tissue samples using inductively coupled plasma mass spectrometry (ICP-MS) detection. Soxhlet, room temperature mixing, sonication, microwave assisted, supercritical carbon dioxide and subcritical water extractions were evaluated for a variety of solvent systems and optimum conditions determined using a partially defatted Lobster Hepatopancreas marine certified reference material, TORT-2 (National Research Council of Canada). The solubility trends and solvents into which the analytes extracted gave an indication as to the polar/non-polar nature of the compounds present. Analytes that prefer water are probably more polar or inorganic, while those preferring methanol solutions are less polar or organic in nature. Arsenic, cadmium, cobalt, molybdenum and selenium were probably all present in TORT-2 in both polar inorganic and non-polar organic forms. While TORT-2 may have contained similar amounts of selenium in both forms, the results suggested that more of the arsenic was present as less polar or more organic compounds, and cobalt existed mainly as more polar or inorganic species. Most of the extraction techniques suggested that, although there may be some less polar organic forms present, more of the cadmium was probably present as polar inorganic compounds. Additionally, most techniques indicated that molybdenum was possibly all less polar or more organic in nature. In general, microwave assisted extraction (MAE) yielded comparable or improved recoveries for all of the analytes monitored and usually required less solvent. Additionally, MAE proved to be the mildest, fastest, least complicated and most reproducible extraction technique evaluated. MAE at 75 degrees C for 2 min exposure time yielded quantitative recovery of arsenic from TORT-2. These conditions were evaluated for lobster tissue samples purchased from a local restaurant. Separate evaluation of the lobster meat and organs resulted in quantitative recoveries of arsenic from both tissue samples. The results indicated that the extraction efficiencies might have some dependence upon the extraction technique, extraction conditions, analyte, solvent, and sample matrix.     

Comparison of extraction techniques for isolation of steroid oestrogens in environmentally relevant concentrations from sediment

The comparison of four extraction techniques for isolation of five native and one labelled steroid oestrogens from sediment was described. The three conventional extraction techniques Soxhlet warm extraction (SWE), accelerated solvent extraction (ASE), microwave-assisted extraction (MAE) and a promising technique QuEChERS were tested for isolation of low environmentally relevant oestrogen concentrations using different extraction conditions. The least expensive and time-consuming method QuEChERS provided the best extraction recoveries (53–84%) from all techniques. MAE achieved the highest recovery from conventional techniques for less polar oestrogens using dichloromethane: acetone 3:1 mixture as an extraction solvent (50–71%), but for extraction of the whole group of oestrogens including more polar estriol acetone or methanol must be used. ASE provided higher extraction recoveries using dichloromethane at 60°C (53–74%) for less polar oestrogens. However, the repeatability of results was unsatisfactory and recoveries using other extraction conditions were lower than for MAE. The most time-consuming SWE achieved the worst extraction recoveries and for isolation of low oestrogen concentrations from sediments, it is completely unsuitable.     

Polyamide as an efficient sorbent for simultaneous interference-free determination of three Sudan dyes in saffron and urine using high-performance liquid chromatography-ultra violet detection北大核心CSCD

With polyamide( PA)as an efficient sorbent for solid phase extraction( SPE)of Sudan dyes II,III and Red 7B from saffron and urine,their determination by HPLC was performed. The optimum conditions for SPE were achieved using 7 mL methanol/water( 1:9,v/v,pH 7)as the washing solvent and 3 mL tetrahydrofu-ran for elution. Good clean-up and high( above 90%)recoveries were observed for all the analytes. The opti-mized mobile phase composition for HPLC analysis of these compounds was methanol-water( 70:30,v/v). The SPE parameters,such as the maximum loading capacity and breakthrough volume,were also determined for each analyte. The limits of detection( LODs),limits of quantification( LOQs),linear ranges and recoveries for the analytes were 4. 6-6. 6 μg/L,13. 0-19. 8 μg/L,13. 0-5 000 μg/L( r2> 0. 99)and 92. 5% -113. 4%,respec-tively. The precisions( RSDs)of the overall analytical procedure,estimated by five replicate measurements for Sudan II,III and Red 7B in saffron and urine samples were 2. 3%,1. 8% and 3. 6%,respectively. The developed method is simple and successful in the application to the determination of Sudan dyes in saffron and urine sam-ples with HPLC coupled with UV detection.     

Optimization of parameters for the analysis of aromatic amines in finger-paints

A study for the optimisation of the supercritical fluid extraction (SFE) of some aromatic amines (4-chloro-o-toluidine, 2-naphthylamine, 4-aminobiphenyl and benzidine) in finger-paints was conducted. The influence of different variables related to the technique on recoveries was investigated. The analytes were subsequently analysed by gas chromatography after SFE. The study allowed the estimation of four main factors (temperature, pressure, static time and volume of modifier) on recoveries by the use of a two-level factor design, where most significant parameters as well as second- and third-order interactions were identified. Other factors, such as type and volume of modifier and time of contact between the spiker solution and the sample prior to extraction, were also studied. The influence of matrix on extraction recovery was also evaluated by applying the method to different finger-paints, and recoveries were similar or even higher in some cases. The drying process of samples was also studied, while classical drying in an oven and microwaves were compared, with similar efficiencies in both methods. The method was validated by extracting the aromatic amines from some commercial finger-paints.     

Evaluation of Soxhlet extraction, accelerated solvent extraction and microwave-assisted extraction for the determination of polychlorinated biphenyls and polybrominated diphenyl ethers in soil and fish samples

Three commonly applied extraction techniques for persistent organic chemicals, Soxhlet extraction (SE), accelerated solvent extraction (ASE) and microwave-assisted extraction (MAE), were applied on soil and fish samples in order to evaluate their performances. For both PCBs and PBDEs, the two more recent developed techniques (ASE and MAE) were in general capable of producing comparable extraction results as the classical SE, and even higher extraction recoveries were obtained for some PCB congeners with large octanol-water partitioning coefficients (K_ow). This relatively uniform extraction results from ASE and MAE indicated that elevated temperature and pressure are favorable to the efficient extraction of PCBs from the solid matrices. For PBDEs, difference between the results from MAE and ASE (or SE) suggests that the MAE extraction condition needs to be carefully optimized according to the characteristics of the matrix and analyte to avoid degradation of higher brominated BDE congeners and improve the extraction yields.     

Coupled solid phase extraction–supercritical fluid extraction–on-line gas chromatography of explosives from water

A method has been developed for the quantitative extraction of nitrotoluenes (2,3-dinitrotoluene, 2,4-dinitrotoluene and trinitrotolugene) from water using a Bakerbond^TM phenyl sorbent. The average solid phase extraction recoveries for spiked standards ranged from 80 to 95 percent for reagent water and 52 to 95 percent from well and surface water in the low ppb and ppt levels. After the nitrotoluenes had been trapped on the solid sorbent they were quantitatively eluted using SFE. Adding toluene to the extraction cell increased the rate of extraction, but did not improve analyte recovery versus unmodified CO₂. The extracts were analyzed off-line with GC–ECD using an internal standard. Extraction losses were due to analyte breakthrough, and not from poor SFE recoveries. This demonstrates that supercritical fluid extraction is a suitable elution technique for analytes trapped on solid phase extraction sorbents. Also, a method for the direct on-line coupling of SPE to GC, using SFE, has been developed and evaluated. Supercritical CO₂ is ideal for directly coupling SPE to GC, since carbon dioxide is a gas under ambient conditions. One potential problem of on-line SPE–SFE–GC is the presence of residual water trapped on the active sites of the Bakerbond¹³ phenyl sorbent. This problem was dealt with by using a split interface previously described by Hawthorne. From the results of this study, the relative standard deviation of the on-line SPE–SFE–GC interface was determined to be between 4 and 10 percent. In addition, there was no significant difference in the precision of the method with or without the use of an internal standard. A calibration curve was also constructed (r² = 0.995) from spiked controls, demonstrating that the method is quantitative.     

Selective on-line immunoextraction coupled to liquid chromatography for the trace determination of benzidine, congeners and related azo dyes in surface water and industrial effluents.

A new extraction immunosorbent involving antigen-antibody interactions was coupled on-line to liquid chromatography for the selective extraction in aqueous samples of benzidine and congeners, widely used as intermediate compounds in the manufacturing of dyes and pigments. Due to the cross-reactivity of the antibodies for analytes with chemical structures closely related to that of the analyte used for immunization, the immunoextraction sorbent was shown to be able to extract aminoazobenzene and related azo dyes with good recoveries. The on-line coupling was optimized for the trace determination of benzidine, dichlorobenzidine, aminoazobenzene and some azo dyes with detection limits in the range 0.1 to 1 microgram/l. The high selectivity of the immunoextraction was shown by comparing the analysis of an industrial textile effluent obtained using precolumns packed either with a non-selective polymeric sorbent or with the anti-benzidine immunosorbent. In such complex samples, extraction and clean-up are achieved in the same step.     

An efficient and fast microwave-assisted extraction method developed for the simultaneous determination of 18 organochlorine pesticides in sediment

An efficient and fast microwave-assisted extraction (MAE) method followed by gas chromatographic separation with mass spectrometric detection (GC–MS) was developed for the extraction of 18 organochlorine pesticides (OCPs) from sediment. Parameters affecting the MAE procedure such as the type and volume of the extraction solvent, irradiation power, temperature and irradiation time were successfully optimised. Under the optimal conditions, extraction efficiencies in the range of 73.4–119% were obtained with THF–HEX (9:1, v/v) for all OCPs studied. The method was linear over the range of 2.9–5000 ng g^?1 with determination coefficients (r²) higher than 0.992 for all analytes. The limits of detection, LODs (S/N = 3), obtained varied from 1.0 to 2.2 ng g^?1 and limits of quantification, LOQs (S/N = 10) were between 2.9 and 6.8 ng g^?1. The proposed method was successfully applied to the analysis of real sediment samples and acceptable recoveries from 70.1 to 124% with RSDs ≤14.8% were obtained. 10 OCPs were determined below their LOQ and 8 OCPs in the range of 124–2830 ng g^?1. The MAE method was compared with Soxhlet, shake flask and ultrasonic solvent extraction techniques. Thus, the MAE–GC–MS method could efficiently be used for selective extraction and quantification of the target analytes from the complex sediment matrices.