2,7-二溴-4-氨基芴的合成及其光学性质

以芴(1)为原料,通过溴代、硝化、还原反应合成了2,7-二溴-4-氨基芴(4),其结构经1H NMR,13C NMR,IR和ESI-MS确证。分别对溴化、硝化和还原反应条件进行优化。结果表明:在最佳溴化反应条件[CHCl3为溶剂,Cu Br2为催化剂,1 90 mmol,n(1)∶n(Cu Br2)∶n(Br2)=1.0∶0.025∶2.89,于0℃反应24 h]下,溴化产物2,7-二溴芴(2)的产率93.8%;在最佳硝化反应条件[2 30 mmol,混合酸(85%硝酸+96%硫酸)为硝化试剂,n(2)∶n(HNO3)=1.0∶4.6,于70℃反应1 h]下,硝化产物2,7-二溴-4-硝基芴(3)的产率94.7%;在最佳还原反应条件(3 30 mmol,Zn/Ca Cl2为还原剂,回流反应4 h)下,4的产率89.5%。运用UV-Vis和荧光光谱初步研究了4的光学性质。结果表明:4的λmax为352.4 nm;在352.4 nm波长激发下,4的λem位于388.4 nm和412.2 nm,光带隙低至2.66 e V。     

壳聚糖缩合呋喃甲醛螯合树脂的合成及性能研究

利用壳聚糖C2 位上活泼氨基与呋喃甲醛缩合反应 ,合成了一种新型树脂。通过L9(34 )正交试验 ,研究了缩合反应的最佳条件 :80℃乙醇中溶胀 1h ,反应 5h ,pH =4.0～ 4.5 ,反应物配比 (氨基摩尔∶醛基摩尔 )为 1∶4,缩合率达到 90 %以上。并测定了上述螯合树脂对过渡金属离子的吸附性能。     

间氯磺酰基苯甲酰氯的合成

三氯甲苯和氯磺酸反应制备了间氯磺酰基苯甲酰氯。反应的最佳条件为:三氯甲苯10 mL(70 mmol),n(三氯甲苯)∶n(氯磺酸)=1∶2,于120℃反应2 h。在最佳反应条件下,收率达81%。     

由聚乙烯醇醇解液合成苄氧胺盐酸盐

首次采用聚乙烯醇醇解废液(Ⅰ,其中乙酸甲酯含量71%,甲醇含量28%)、盐酸羟胺(2)和氯化苄(4)为原料,经酰胺化、醚化和水解反应合成了苄氧胺盐酸盐,纯度99.3%,总收率90.2%,其结构经IR确证。分别采用L9(33)和L9(43)正交实验对酰胺化反应和醚化反应条件进行优化。最佳酰胺化反应条件为:2 70 mmol,n(2)∶n(Ⅰ)∶n(NaOH)=1.00∶2.03∶2.00,于40℃反应3 h,收率95.3%。最佳醚化条件为:乙酰氧肟酸(3)70 mmol,n(3)∶n(4)=1.00∶1.05,DMF 30 mL,于90℃反应5 h,收率92.0%。     

Na_(12)[WZn_3(H_2O)_2(ZnW_9O_(34))_2]催化剂的制备及其催化活性

采用重结果法制备了催化剂Na12[WZn3(H2O)2(ZnW9O34)2](CatZn)。以1,2-丙二醇(1)催化选择性氧化制备羟基丙酮(2)为探针反应考察了CatZn的催化性能。在最佳反应条件[1 50 mmol,n(CatZn)∶n(1)=0.06,n(H2O)∶n(1)=1.4,n(H2SO4)∶n(1)=0.15,于70℃反应1.5 h]下,收率43.85%,选择性68.87%。     

4-氯苯乙醇的合成

以4-氯苯乙酸为起始原料,耦合酯化和还原反应合成了4-氯苯乙醇(1),其结构经1H NMR和MS表征。较适宜的反应条件为:4-氯苯乙酸30 mmol,无水乙醇120 mmol,n(4-氯苯乙酸)∶n(SOCl2)∶n(NaBH4)=1.0∶0.5∶1.6,于室温反应3 h完成酯化反应,产物不经分离直接于75℃反应5 h完成还原反应,1收率高于95%,含量大于99%。     

4-(3,4-二甲氧基苯基)-5-硝基哌啶-2-酮的合成

以3-(3,4-二甲氧基苯基)-4-硝基丁酸甲酯(4),氨水和甲醛为原料,异丙醇溶液为溶剂,经曼尼希-酯胺解偶联反应合成了新化合物4-(3,4-二甲氧基苯基)-5-硝基哌啶-2-酮,其结构经1H NMR,13C NMR和EI-MS表征。在最佳反应条件{4 1.0 mmol,n(4)∶n(27%氨水)∶n(37%甲醛)=1.00∶1.30∶1.05,异丙醇[V(异丙醇)∶V(水)=5∶1]7.5 m L,于100℃反应12 h}下,收率74.1%。     

叔丁基二苯基氢硅烷的合成方法研究

以叔丁基二苯基氯硅烷(SCl)为原料,硼氢化钾/氯化锌(KBH_4/ZnCl_2)为还原体系,制备了叔丁基二苯基氢硅烷(SH),产物结构经~1H-NMR确证。通过单因素、正交实验和放大重复性实验确定了最佳反应条件为n(KBH_4)∶n(ZnCl_2)∶n(SCl)为2∶1.25∶1,100℃反应18h,平均收率为93.7%。该法具有原料易得,反应温和,操作方便,收率高,对环境友好等优点,适合工业化生产。     

离子液体/相转移催化剂促进的二茂铁基查尔酮的合成

乙酰基二茂铁与芳香醛在离子液体或相转移催化剂作用下进行Claisen-Schmidt缩合,高产率地合成二茂铁基查尔酮.其中,相转移催化剂能更有效地催化该反应,优化后的反应条件为:无水乙醇溶液,35℃,n(乙酰基二茂铁)∶n(芳香醛)∶n(四丁基六氟磷酸铵)∶n(NaOH)=1∶1∶2.5∶0.75.     

新型含双长链和苄基的有机硅季铵盐的合成

以双十二胺(1)为原料,与氯化苄经取代反应制得中间体苄基双十二胺(2);2与γ-氯丙基三甲氧基硅烷(3)经季铵化反应合成了一种新型的含双长链和苄基的有机硅季铵盐(4),其结构经UV-Vis和FT-IR表征。通过正交实验L9(34)优化了2和4的反应条件。合成2的最佳工艺条件为:以乙腈为溶剂,1 5 mmol,n(1)∶n(Bn Cl)=1.0∶1.2,回流反应20 h,收率80.4%。合成4的最佳工艺条件为:以乙二醇为溶剂,2 5mmol,n(2)∶n(3)=1.0∶1.6,于110℃密闭反应80 h,收率57.8%。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.