市售蘑菇中微量元素测定分析

采用原子吸收分光光度法测定了银川市大型超市里10种新鲜蘑菇中的锰、铁、锌和铜含量。各元素测定方法的变异系数为1.9%~4.2%,回收率在92.1%~104.0%之间。结果表明,锰、铁、锌和铜在蘑菇中含量的分布分别为6.75%~23.64%,80.37%~233.40%,28.00%~118.7%,2.55%~40.69%。测定结果对评价市售蘑菇微量元素营养价值具有参考意义。     

全蝎中4种微量元素的形态分析

对中药全蝎中铜、锌、铁和镁4种微量元素存在的形态及含量进行了研究。文中叙述了全蝎样品中元素的各种形态(可溶态、悬浮态、无机态、有机态)的提取方法和分离,采用火焰原子吸收光谱法测定了各试液中4种微量元素的含量。结果显示,全蝎中4种元素的总提取率在39.9%~63.2%之间,浸留比在73.6%~126.0%之间,悬浮态颗粒吸附率在10%左右,铜、锌、铁、镁的有机态与无机态的比例在250.0%~550.0%之间。     

微波消解-ICP-AES法同时测定绞股蓝中4种微量元素

采用微波消解法,以HNO3-H2O2对样品进行处理,用电感耦合等离子体发射光谱法(ICP-AES)同时测定了绞股蓝中的铁、锰、铜、锌4种微量元素。结果表明,所测样品中的元素含量按铁、锰、锌、铜顺序递减,各元素测定结果的相对标准偏差在1.0%~3.8%之间,回收率在88%~97%之间。方法简单,有实用意义。     

原子荧光光谱法测定铜合金中铋元素含量方法改进

基于原子荧光光谱法测定铋元素时检出限低、测定结果稳定且准确等优点,研究原子荧光光谱法测定铜合金中铋元素含量的方法。在标准系列中加入相近浓度的铜元素标准溶液,原子荧光光谱法测定铜合金中铋元素含量。称取0.1 g样品,加入10 mL硝酸溶解,10%硫脲-5%抗坏血酸溶液7.5 mL预处理样品。在20μg/L的铋标准溶液中加入6 mL浓度为1000μg/mL的铜元素标准溶液。结果表明:在0~20μg/L范围内,该方法线性关系良好,线性方程为I=138.1670c+43.8572,相关系数为0.9996,所测定的样品中铋元素含量的相对误差在-4.3%~7.7%之间,精密度在0.4%~4.7%之间。原子荧光光谱法可作为铜合金中铋元素含量测定的方法。     

电感耦合等离子体发射光谱法测定稀土发火合金中铁、镁、铜和锌

采用盐酸辅以加热的方式处理稀土发火合金样品,以电感耦合等离子体原子发射光谱法测定稀土发火合金中铁、镁、铜和锌含量。采用矩阵模拟实验优化分析谱线,利用多点定标校正曲线法计算测量结果。在最佳实验条件下,稀土发火合金中的基体元素对待测元素的测定结果无明显影响,各元素在检测范围内线性关系良好,相关系数均为0.999 9,方法检出限为0.001~0.010μg/m L。测定结果的相对标准偏差为1.10%~1.75%(n=11),样品加标回收率在96.00%~104.05%之间。该方法简便、快速且具有较高的灵敏度,适用于稀土发火合金中铁、镁、铜、锌等非稀土元素的测定。     

微波消解-火焰原子吸收光谱法测定中药女贞子中9种金属元素

用微波消解法处理样品,用硝酸-过氧化氢(4+1)混合溶液作为消解剂进行微波消解,火焰原子吸收光谱法测定了中药女贞子中钙、镁、钾、钠、铁、锶、锰、铜和锌元素含量。9种元素检出限(3S/N)在0.000 6~0.024 8 mg.L-1之间,回收率在93.0%~107.3%之间,相对标准偏差(n=10)在0.86%~4.39%之间。试验结果表明:女贞子中钾、钙、镁、铁、钠、锌、锰、铜和锶质量分数分别为16 940,1 790,1 640,467.8,116.0,24.5,15.0,9.6,1.9μg.g-1,锌与铜含量的比值为2.55。由此可见,女贞子中钙、镁、钾元素含量丰富,铁含量也较高。为探讨中药金属元素种类及含量与治疗心血管疾病的关系等提供有用数据。     

乌贼骨中微量元素测定方法对比

乌贼骨样品经高压消化罐消解,采用电感耦合等离子体原子发射光谱法(ICP-AES)和火焰原子吸收光谱法(FAAS)分别测定了样品中铁、锌、铜、锰、钙、镁、钴、镍、钾、铬、硅、铝、鉛和镉等14种微量元素的含量。结果表明:两种方法的回收率分别在96.5%~107.1%(FAAS)和96.7%~100.3%(ICP-AES)之间,相对标准偏差分别为0.7%~3.0%(FAAS)和0.2%~2.2%(ICP-AES)。经F法和t法检验,ICP-AES和FAAS测定微量元素含量的测定值之间无显著性差异。     

花椒中五种微量元素含量的测定

采用原子吸收光谱法,测定了河南太行山区花椒及椒皮、椒籽中锰、铁、铜、锌、铅的含量。结果显示,各元素在实验范围内,线性关系良好,回收率在92%~103%之间。花椒及椒皮、椒籽中均含有微量元素,花椒中锰、铁、铜、锌、铅的含量分别为78.851、90.868、11.571、18.818、0.086μg.g-1,其中锰、铁含量丰富,有害元素铅的含量极低。椒籽中铁、铜、锌的分布量大于椒皮;椒皮中锰的分布量大于椒籽。为探讨花椒的高药用价值提供了有力的证据,椒籽中铜、锌、铁含量高于椒皮,应大力开发利用。     

ICP-AES法测定菜头肾中多种微量元素

为探讨测定菜头肾中多种微量元素的方法,采用HNO3-HC lO4体系湿法消化,运用ICP-AES法测定了菜头肾中的多种微量元素。结果表明,菜头肾中K、Ca、Mg、P、S、A l、Na、Fe、Mn等元素含量相对较高,变异系数范围在0.23%~8.92%之间,元素的回收率在82.9%~106.1%之间。该法简便快速,可同时测定菜头肾中多种微量元素。     

火焰原子吸收法测定煤渣和煤质活性炭中铁、钙、镁、锌、铅

建立了火焰原子吸收法测定煤渣和煤质活性炭中微量金属元素铁、钙、镁、锌、铅含量的方法。煤渣样品采用干灰化后消解,煤质活性炭样品采用稀酸提取进行处理。煤渣中铁、钙、镁元素用标准曲线法定量,活性炭中铁、锌、铅则采用标准加入法定量以减少基体干扰的影响。样品测定结果与文献报道相一致,煤渣尤其是燃烧处理后的煤渣中微量元素含量较高,而煤质活性炭通过复杂工艺处理后,微量元素大大减少。样品中被测元素的加标回收率在88.5%~105.5%之间,测定结果的相对标准偏差小于2%(n=7),两类样品中6种元素的检出限分别为0.010,0.015,0.005,0.012,0.013,0.110 mg/L。火焰原子吸收法测定微量元素准确度高、重现性好,适合煤渣和活性炭中微量金属元素的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.