Synthesis of cobalt ferrite core/metallic shell nanoparticles for the development of a specific PNA/DNA biosensor

Controlled synthesis of cobalt ferrite superparamagnetic nanoparticles covered with a gold shell has been achieved by an affinity and trap strategy. Magnetic nanoparticles are functionalized with a mixture of amino and thiol groups that facilitate the electrostatic attraction and further chemisorption of gold nanoparticles, respectively. Using these nanoparticles as seeds, a complete coating shell is achieved by gold salt-iterative reduction leading to monodisperse water-soluble gold-covered magnetic nanoparticles, with an average diameter ranging from 21 to 29 nm. These constitute a versatile platform for immobilization of biomolecules via thiol chemistry, which is exemplified by the immobilization of peptide nucleic acid (PNA) oligomers that specifically hybridize with complementary DNA molecules in solution. Hybridation with DNA probes has been measured using Rhodamine 6G fluorescence marker and the detection of a single nucleotide mutation has been achieved. These results suggest the PNA-nanoparticles application as a biosensor for DNA genotyping avoiding commonly time-consuming procedures employed.     

Influences of non-selective interactions of nucleic acids on response rates of nucleic acid fiber optic biosensors

The immobilization of oligonucleotides to solid surfaces can provide a platform of chemistry that is suitable for the development of biosensor and microarray technologies. Experiments were performed using a fiber optic nucleic acid biosensor based on total internal reflection fluorescence to examine the effects of the presence of non-complementary DNA on the detection of hybridization of complementary target DNA. The work has focused on the rates and extent of hybridization in the presence and absence of non-selective adsorption using fluorescein-labeled DNA. A stop-flow system of 137 μL volume permitted rapid introduction and mixing of each sample. Response times measured were on the order of seconds to minutes. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on the extent of hybridization of complementary oligonucleotides, but actually reduced the response times of sensors to cDNA oligonucleotides. Received: 26 September 2000 / Revised: 24 November 2000 / Accepted: 30 November 2000     

Hybridization Study of PNA-DNA in the Solution and Surface-Solution Interface for Biosensor Application

Abstract

Hybridization of 12-mers peptide nucleic acid (PNA) to complementary DNA was investigated in solution and on gold surfaces. The oligomers were designed to improve mismatch discrimination and minimize formation of secondary structures. Thermal denaturation experiments indicate high thermal stabilities for PNA-DNA hybrid with T _m values close to calculated values. Hybridization of PNA-DNA at 45°C and room temperature showed no difference. Hybridization on gold surface was also investigated with complementary and noncomplementary DNAs. The results show that 12-mer PNA and DNA hybridization at room temperature retained high specificity within ～5 ng.     

Colloid Au-enhanced DNA immobilization for the electrochemical detection of sequence-specific DNA

We use colloidal Au to enhance the DNA immobilization amount on a gold electrode and ultimately lower the detection limit of our electrochemical DNA biosensor. Self-assembly of approximately 16-nm diameter colloidal Au onto a cysteamine modified gold electrode resulted in an easier attachment of an oligonucleotide with a mercaptohexyl group at the 5′-phosphate end, and therefore an increased capacity for nucleic acid detection. Quantitative results showed that the surface densities of oligonucleotides on the Au colloid modified gold electrode were approximately (1–4)×10¹⁴ molecules cm⁻². Hybridization was induced by exposure of the ssDNA-containing gold electrode to ferrocenecarboxaldehyde labeled complementary ssDNA in solution. The detection limit is 5×10⁻¹⁰ mol l⁻¹ of complementary ssDNA, which is much lower than our previous electrochemical DNA biosensors. The Au nanoparticle films on the Au electrode provide a novel means for ssDNA immobilization and sequence-specific DNA detection.     

Silica-nanoparticle-based interface for the enhanced immobilization and sequence-specific detection of DNA

A biocompatible and uniform interface based on silica nanoparticles derivatized with amino groups has been constructed for the effective immobilization and sensitive sequence-specific detection of calf thymus DNA. Atomic force microscopy (AFM) and scanning electron microscopy (SEM) results showed that a monolayer of silica nanoparticles can be formed on a gold electrode under our experimental conditions using cysteine self-assembly monolayer as binder medium. Electrochemical impedance spectroscopy and X-ray photoelectron spectroscopy (XPS) verified the successful immobilization of DNA on silica-nanoparticle-modified gold electrodes. Quantitative results demonstrated that enhanced immobilization of single-strand DNA (ss-DNA) up to 1.6×10^–8 mol cm^–2 could be achieved owing to the larger surface area and the special properties of silica nanoparticles. In addition, hybridization experiments demonstrated that the immobilized ss-DNA on silica nanoparticles could specifically interact with complementary DNA in solutions.     

Selective Immobilization of Gold Nanoparticles on the Surface of a Photoreactive Polymer

Summary. A photoreactive polymer containing thiocyanate (SCN) groups was employed for the immobilization of gold nanoparticles (AuNP). Upon UV illumination, isothiocyanate (NCS) groups are generated at the surface by photoisomerization. The illuminated areas of the polymer layer containing NCS were selectively modified with 2-aminoethanethiol to give SH terminated thiourea units at the surface. Gold nanoparticles were selectively immobilized in these areas by immersing the polymer surface in a colloidal solution of gold nanoparticles stabilized by citric acid. Depending on the time of immersion, different amounts of gold were deposited on the illuminated areas, while no immobilization of AuNP was observed in the non-illuminated areas. By using photolithographic masks, patterned gold structures (μm scale) were produced on the polymer surface.     

Selective Immobilization of Gold Nanoparticles on the Surface of a Photoreactive Polymer

A photoreactive polymer containing thiocyanate (SCN) groups was employed for the immobilization of gold nanoparticles (AuNP). Upon UV illumination, isothiocyanate (NCS) groups are generated at the surface by photoisomerization. The illuminated areas of the polymer layer containing NCS were selectively modified with 2-aminoethanethiol to give SH terminated thiourea units at the surface. Gold nanoparticles were selectively immobilized in these areas by immersing the polymer surface in a colloidal solution of gold nanoparticles stabilized by citric acid. Depending on the time of immersion, different amounts of gold were deposited on the illuminated areas, while no immobilization of AuNP was observed in the non-illuminated areas. By using photolithographic masks, patterned gold structures (μm scale) were produced on the polymer surface.     

Dispersions based on noble metal nanoparticles-DNA conjugates

Many biomolecules have specific binding properties in the nanostructure formation; they are attractive materials for nanotechnology. One such promising construction material for growing a well-defined nanostructure is deoxyribonucleic acid, due to its π-electron hydrophobic core and predictable recognition attributed to the specificity of Watson–Crick base-pairing. Hydrogen bonding provides the specificity behind the matching of complementary pairs of single-stranded (ss) DNA to hybridize into a double strand (ds) of helical DNA. The double-helical structure of DNA is determined by a subtle balance of noncovalent interactions among the DNA building blocks. The most prominent role is played by the interactions between the DNA bases, where two binding motifs can be recognized: planar hydrogen bonding and vertical stacking. DNA-based nanotechnology has generated interest in a number of applications due to the specificity, programmability, and reproducibility of DNA interaction with noble metal nanoparticles. 5′ and 3′ thiol moieties are used to prepare composite DNAs, DNA–gold nanoparticle conjugates and nanostructures with a variety of nanoparticle-based DNA assays. Particularly, color changes induced by the association of nanometer-sized gold particles provide a basis of a simple yet highly selective method for detecting specific biological reactions between anchored ligand molecules and receptor molecules in the milieu. Colloidal noble metal nanoparticles, in particular, have found application in a variety of assay formats in which analyte binding is coupled to particle adsorption. The extreme sensitivity of the bandwidth, the peak height, and the position of the absorption (or scattering) maximum of surface plasmon resonance spectra to environmental changes have prompted the development of approaches directly monitor the DNA hybridization. The same features that make DNA an effective molecule for the storage of genetic information also render it useful as an engineering material for the construction of smart objects at the nanometer scale because of its ability to self organize into desired structures via the specific hybridization of complementary sequences. Biocompatibility between gold nanomaterials and biological scaffolding is crucial to the development of smart biomaterials. These DNA/metal colloids are interesting for their fundamental properties as well as for applications in nanomaterials science and nanobiotechnology.     

Nanomechanics of the formation of DNA self-assembled monolayers and hybridization on microcantilevers

Biomolecular interactions over the surface of a microcantilever can produce its bending motion via changes of the surface stress, which is referred to nanomechanical response. Here, we have studied the interaction forces responsible for the bending motion during the formation of a self-assembled monolayer of thiolated 27-mer single-stranded DNA on the gold-coated side of a microcantilever and during the subsequent hybridization with the complementary nucleic acid. The immobilization of the single-stranded DNA probe gives a mean surface stress of 25 mN/m and a mean bending of 23 nm for microcantilevers with a length and thickness of about 200 microm and 0.8 microm, respectively. The hybridization with the complementary sequence could not be inferred from the nanomechanical response. The nanomechanical response was compared with data from well-established techniques such as surface plasmon resonance and radiolabeling, to determine the surface coverage and study the intermolecular forces between neighboring DNA molecules anchored to the microcantilever surface. From both techniques, an immobilization surface density of 3 x 10(12) molecules/cm(2) and a hybridization efficiency of 40% were determined. More importantly, label-free hybridization was clearly detected in the same conditions with a conventional sensor based on surface plasmon resonance. The results imply that the nanomechanical signal during the immobilization process arises mainly from the covalent attachment to the gold surface, and the interchain interactions between neighboring DNA molecules are weak, producing an undetectable surface stress. We conclude that detection of nucleic acid hybridization with nanomechanical sensors requires reference cantilevers to remove nonspecific signals, more sensitive microcantilever geometries, and immobilization chemistries specially addressed to enhance the surface stress variations.     

Fabrication of a Sensitive Impedance Biosensor of DNA Hybridization Based on Gold Nanoparticles Modified Gold Electrode

In this work, we report on the preparation of a simple, sensitive DNA impedance sensor. Firstly gold nanoparticles were electrodeposited on the surface of a gold electrode, and then probe DNA was immobilized on the surface of gold nanoparticles through a 5′‐thiol‐linker. Electrochemical impedance spectroscopy (EIS) was used to investigate probe DNA immobilization and hybridization. Compared to the bare gold electrode, the gold nanoparticles modified electrode could improve the density of probe DNA attachment and the sensitivity of DNA sensor greatly. The difference of electron transfer resistance (ΔR_et) was linear with the logarithm of complementary oligonucleotides sequence concentrations in the range of 2.0×10^?12 to 9.0×10^?8 M, and the detection limit was 6.7×10^?13 M. In addition, the DNA sensor showed a fairly good reproducibility and stability during repeated regeneration and hybridization cycles.     

Direct selective detection of genomic DNA from coliform using a fiber optic biosensor

Fiber optic biosensors operated in a total internal reflection format were prepared based on covalent immobilization of 25mer lacZ single-stranded nucleic acid probe. Genomic DNA from Escherichia coli was extracted and then sheared by sonication to prepare fragments of approximately 300mer length. Other targets included a 25mer fully complementary lacZ sequence, 100mer polymerase chain reaction (PCR) products containing the lacZ sequence at various locations, and non-complementary DNA including genomic samples from salmon sperm. Non-selective adsorption of non-complementary oligonucleotides (ncDNA) was found to occur at a significantly faster rate than hybridization of complementary oligomers (cDNA) in all cases. The presence of ncDNA oligonucleotides did not inhibit selective interactions between immobilized DNA and cDNA in solution. The presence of high concentrations of non-complementary genomic DNA had little effect on extent or speed of hybridization of complementary oligonucleotides. Detection of genomic fragments containing the lacZ sequence was possible in as little as 20 s by observation of the steady-state fluorescence intensity increase or by time-dependent rate of fluorescence intensity changes.     

Application of diazo-thiourea and gold nano-particles in the design of a highly sensitive and selective DNA biosensor

An effective procedure for constructing a DNA biosensor is developed based on covalent immobilization of NH_2 labeled,single strand DNA(NH_2-ssDNA) onto a self-assembled diazo-thiourea and gold nanoparticles modified Au electrode(diazo-thiourea/GNM/Au).Gold nano-particles expand the electrode surface area and increase the amount of immobilized thiourea and single stranded DNA(ssDNA) onto the electrode surface.Diazo-thiourea film provides a surface with high conductibility for electron transfer and a bed for the covalent coupling of NH_2-ssDNA onto the electrode surface.The immobilization and hybridization of the probe DNA on the modified electrode is studied by differential pulse voltammetry(DPV) using methylene blue(MB) as a well-known electrochemical hybridization indicator.The linear range for the determination of complementary target ssDNA is from 9.5(±0.1) × 10~(-13) mol/L to1.2(±0.2) x 10~(-9) mol/L with a detection limit of 1.2(±0.1) 10~(-13) mol/L.     

Construction of Deoxyribonucleic Acid Decorated Gold Nanostructures as Nanomedical Agents

Gold nanoparticles provide promising applications based on their versatile properties of electromagnetic scattering and absorption and the capability of photothermal transduction relying on their size and shape. Because of their high tolerance to the environment and their excellent biocompatibility, gold nanoparticles are the most recognized nanomaterial applied in biomedicine. Deoxyribonucleic acid (DNA) is a native biomaterial that stores genetic information in living organisms. Naturally, DNA can be combined with gold nanoparticles for a variety of biomedical purposes. For example, the reversible hydrogen bonding of the complementary double‐stranded structures has been employed to serve as a gate keeper for the control of drug release on demand. Besides, the complementary hybridization behavior has given the specific recognition in nucleic acid for sensing feature. Accordingly, this mini‐review describes how DNA–gold nanoconjugates have been formulated and aimed for drug release and sensing analysis as well as the hybrids of aptamer–gold analogy for biomedical studies. These nanoconjugates show the potential for preclinical and clinical treatments.     

Amplified electrochemical detection of nucleic acid hybridization via selective preconcentration of unmodified gold nanoparticles

The common drawback of optical methods for rapid detection of nucleic acid by exploiting the differential affinity of single-/double-stranded nucleic acids for unmodified gold nanoparticles (AuNPs) is its relatively low sensitivity. In this article, on the basis of selective preconcentration of AuNPs unprotected by single-stranded DNA (ssDNA) binding, a novel electrochemical strategy for nucleic acid sequence identification assay has been developed. Through detecting the redox signal mediated by AuNPs on 1, 6-hexanedithiol blocked gold electrode, the proposed method is able to ensure substantial signal amplification and a low background current. This strategy is demonstrated for quantitative analysis of the target microRNA (let-7a) in human breast adenocarcinoma cells, and a detection limit of 16 fM is readily achieved with desirable specificity and sensitivity. These results indicate that the selective preconcentration of AuNPs for electrochemical signal readout can offer a promising platform for the detection of specific nucleic acid sequence.     

Electroactive chitosan nanoparticles for the detection of single-nucleotide polymorphisms using peptide nucleic acids

Here we report an electrochemical biosensor that would allow for simple and rapid analysis of nucleic acids in combination with nuclease activity on nucleic acids and electroactive bionanoparticles. The detection of single-nucleotide polymorphisms (SNPs) using PNA probes takes advantage of the significant structural and physicochemical differences between the full hybrids and SNPs in PNA/DNA and DNA/DNA duplexes. Ferrocene-conjugated chitosan nanoparticles (Chi-Fc) were used as the electroactive indicator of hybridization. Chi-Fc had no affinity towards the neutral PNA probe immobilized on a gold electrode (AuE) surface. When the PNA probe on the electrode surface hybridized with a full-complementary target DNA, Chi-Fc electrostatically attached to the negatively-charged phosphate backbone of DNA on the surface and gave rise to a high electrochemical oxidation signal from ferrocene at ∼0.30 V. Exposing the surface to a single-stranded DNA specific nuclease, Nuclease S1, was found to be very effective for removing the nonspecifically adsorbed SNP DNA. An SNP in the target DNA to PNA made it susceptible to the enzymatic digestion. After the enzymatic digestion and subsequent exposure to Chi-Fc, the presence of SNPs was determined by monitoring the changes in the electrical current response of Chi-Fc. The method provided a detection limit of 1 fM (S/N = 3) for the target DNA oligonucleotide. Additionally, asymmetric PCR was employed to detect the presence of genetically modified organism (GMO) in standard Roundup Ready soybean samples. PNA-mediated PCR amplification of real DNA samples was performed to detect SNPs related to alcolohol dehydrogenase (ALDH). Chitosan nanoparticles are promising biometarials for various analytical and pharmaceutical applications. Figure The electrochemical method for SNP detection using PNA probes and chitosan nanoparticles takes advantage of the significant structural and physicochemical differences between PNA/DNA and DNA/DNA duplexes. Single-stranded DNA specific enzymes selectively choose these SNP sites and hydrolyze the DNA molecules on gold electrode (AuE) surface. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

脱氧核糖核酸在电极表面的固定化研究进展

介绍了电化学脱氧核糖核酸(DNA)传感器的原理并重点评述了DNA在不同材料电极表面的固定化技术,对比了吸附法、自组装法、亲和素一生物素法、共价键合法以及组合法固定DNA在构建电化学DNA传感器中的应用。参考文献77篇。     

The nanoscale description of acid penetration to the gold colloids encapsulated in silica sol–gel matrix

Various sizes of gold nano colloidal particles ranging from 5 nm to 100 nm of size were encapsulated in a silica based sol–gel, and these surfaces were exposed to a pH 1 acid solution. This enabled us to observe the process of solvent intrusion and interaction with gold colloids by the absorption spectrum as a function of time. The rate was analyzed by a single exponential analytical function, and the maximum rate was found for gold colloid of 15 nm size. The least acid interaction and colour change was observed for the size of 60 nm. It was speculated that the surface of these gold colloids were homogeneously covered by the sodium tetra-borate buffer which insulated silica gel layer, thus avoiding direct contact of the acid with the surface of the gold colloid. This study confirmed that the nano scale dopant size affects the rate of solvent penetration into a sol–gel cavity.     

Nonenzymatic synthesis of RNA and DNA oligomers on hexitol nucleic acid templates: the importance of the A structure.

Hexitol nucleic acid (HNA) is an analogue of DNA containing the standard nucleoside bases, but with a phosphorylated 1,5-anhydrohexitol backbone. HNA oligomers form duplexes having the nucleic acid A structure with complementary DNA or RNA oligomers. The HNA decacytidylate oligomer is an efficient template for the oligomerization of the 5'-phosphoroimidazolides of guanosine or deoxyguanosine. Comparison of the oligomerization efficiencies on HNA, RNA, and DNA decacytidylate templates under various conditions suggests strongly that only nucleic acid double helices with the A structure support efficient template-directed synthesis when 5'-phosphoroimidazolides of nucleosides are used as substrates.     

Study on the immobilization of anti-IgG on Au-colloid modified gold electrode via potentiometric immunosensor, cyclic voltammetry, and electrochemical impedance techniques

The immobilization of anti-IgG on Au-colloid modified gold electrodes has been investigated. A cleaned gold electrode was first immersed in a mercaptoethylamine (AET) solution, and then gold nanoparticles were chemisorbed onto the thiol groups of the mercaptoethylamine. Finally, anti-IgG was adsorbed onto the surface of the gold nanoparticles. Potentiometric immunosensor, cyclic voltammetry, and electrochemical impedance techniques were used to investigate the immobilization of anti-IgG on Au colloids. In the impedance spectroscopic study, an obvious difference of the electron transfer resistance between the Au-colloid modified electrode and the bare gold electrode was observed. The cyclic voltammogram tends to be more irreversible with increased anti-IgG concentration. Using the potentiometric immunosensor, the proposed technique is based on that the specific agglutination of antibody-coated gold nanoparticles, averaging 16 nm in diameter, in the presence of the corresponding antigen causes a potential change that is monitored by a potentiometry. It is found that the developed immunoagglutination assay system is sensitive to the concentration of IgG antigen as low as 12 ng mL(-1). Experimental results showed that the developed technique is in satisfactory agreement with the ELISA method, and that gold nanoparticles can be used as a biocompatible matrix for antibody or antigen immobilization.     

Synthesis and adsorption properties of colloid-imprinted mesoporous carbons using poly(vinylidene chloride-co-vinyl chloride) as a carbon precursor

A facile synthesis of micro- and mesoporous carbons has been proposed using colloidal silica nanoparticles with diameter of ∼24 nm and poly(vinylidene chloride-co-vinyl chloride) (Saran) as a carbon precursor. The resulting carbons possessed large specific surface area, ∼800 m²/g, and approximately the same volume of micro- and mesopores, each about 50% of the total pore volume. While the size of micropores was around 1 nm, the large and uniform spherical mesopores (about 24 nm) resemble the diameters of silica colloids used. Nitrogen adsorption measurements proved that these mesopores were interconnected and accessible. The well-developed microporosity was created mainly by decomposition of Saran copolymer during carbonization.