Direct synthesis of plugged SBA-15 type mesoporous silica using alcoholamines

Plugged mesoporous SBA-15 having a 2-D hexagonal pore structure could be directly synthesized under acidic conditions using P123 as a supramolecular template, sodium metasilicate and alcoholamines. The use of alcoholamines seemed to play roles as capturing agents for silica sources that could form internal porous plugs.     

Inorganic/organic mesoporous silica as a novel fiber coating of solid-phase microextraction

Mesoporous materials were employed as fast, sensitive and efficient fiber coatings of solid-phase microextraction (SPME) for the first time. Three micrometer as-synthesized C₁₆-MCM-41 particles were immobilized onto stainless steel wire with 100 μm coating thickness. In combination with high performance liquid chromatography (HPLC), extraction efficiency and selectivity of C₁₆-MCM-41 were investigated using aromatic hydrocarbons. Effect of extraction and desorption time, extraction temperature, stirring rate and ionic strength on extraction efficiency were examined. Aanalytical merits of SPME with C₁₆-MCM-41 coating were evaluated. The chromatographic peak area is proportional to the concentration of anthracene in the range 0.5-150 μg l⁻¹. The limit of detection was 0.05 μg l⁻¹ (S/N=3) and the relative standard deviation (R.S.D.) was 0.033%.     

Electrodeposited polyaniline as a fiber coating for solid-phase microextraction of organochlorine pesticides from water

The study on the performance of polyaniline as a fiber coating for solid-phase microextraction (SPME) purposes has been reported. Polyaniline coatings were directly electrodeposited on the surface of a stainless steel wire and applied for the extraction of some organochlorine pesticides (OCPs) from water samples. Analyses were performed using GC-electron capture detection (GC-ECD). The results obtained show that polyaniline fiber coating is suitable for the successful extraction of organochlorine compounds. This behavior is most probably due to the porous surface structure of polyaniline film, which provides large surface areas and allowed for high extraction efficiency. Experimental parameters such as adsorption and desorption conditions were studied and optimized. The optimized method has an acceptable linearity, with a concentration range of 1-5000 ng/L. Single fiber repeatability and fiber-to-fiber reproducibility were less than 12 and 17%, respectively. High environmental resistance and lower cost are among the advantages of polyaniline fibers over commercially available SPME fibers. The developed method was applied to the analysis of real water samples from Yangtse River and Tianmu Lake.     

Determination of polycyclic aromatic hydrocarbons by solid-phase microextraction coupled to HPLC using a fiber with mesoporous silica coating

A novel SPME-HPLC method was developed for the determination of trace amounts of polycyclic aromatic hydrocarbons (PAHs). It was found that the SPME device with C₈H₁₇-SBA-15 (C ₈-SBA-15) mesoporous silica coating had high extraction efficiency, sufficient chemical and hydrothermal stability and good reversibility. The determination conditions for environmental pollutants like PAHs including extraction and desorption time, extraction temperature, ionic strength and stirring rate were optimized. Under optimized experimental conditions, results with good accuracy (with a recovery of 97.5–101.7%), precision (with a standard deviation of 0.15–1.07%) and low detection limit (LOD, 0.05–0.25 μg/L) were obtained, suggesting the SPME devices using chemical modified SBA-15 as coating material are promising in preconcentration, separation and determination of interested analytes in the future.     

Optimisation of alachlor solid-phase microextraction from water samples using experimental design

We have tested screening and response surface experimental designs to optimise the solid-phase microextraction (SPME) of the widely used herbicide alachlor. Extraction time and sample volume were the only statistically significant factors from those studied. In the final optimised conditions the procedure was applied to the SPME-HPLC analysis of alachlor in spiked water samples with excellent figures of merit.     

Amino-functionalized SBA-15 type mesoporous silica having nanostructured hexagonal platelet morphology

Amino-functionalized SBA-15 type mesoporous silicas having unique hexagonal platelet morphologies with short channels (100-300 nm) running parallel to the thickness of the nanostructured hexagonal platelet type morphologies have been directly synthesized by co-condensation of aminopropyltriethoxysilane (APTES) and sodium metasilicate as a silica source in the presence of Pluronic P123 triblock copolymer as a structure directing agent.     

Determination of organochlorine pesticides in ground water samples using solid-phase microextraction by gas chromatography-electron capture detection

A direct immersion solid-phase microextraction coupled with gas chromatography-electron capture detection (SPME-GC-ECD) method was optimized and validated for the quantitative determination of 18 organochlorine pesticides in ground water. Ionic strength, stirring speed, adsorption and desorption time and pH were some of the parameters investigated in order to select the optimum conditions for SPME with a 50/30 DVB/CAR/PDMS fiber coating. The SPME-GC/ECD method showed good linear response below 10 ng L⁻¹ with R² values in the range of 0.9950–0.9997. The repeatability of the measurements were lower than 10%. Values of relative recoveries located within the acceptable range (80–120%). Limits of quantification (LOQ) from 4.5 × 10⁻³ to 1.5 ng L⁻¹ were obtained. On average 8 organochlorines were found per sample, even so all the 18 organochlorines were quantified among them. Substances such as endrin ketone, γ-BHC and β-BHC were the pesticides determined in larger concentration (0.06–305 ng L⁻¹), while methoxychlor and aldrin in smaller amounts (0.151–1.55 ng L⁻¹). Measured levels of organochlorine pesticides were above the limits established by Brazilian regulations.     

High extraction efficiency for polar aromatic compounds in natural water samples using multiwalled carbon nanotubes/Nafion solid-phase microextraction coating

A novel solid-phase microextraction (SPME) fiber coated with multiwalled carbon nanotubes (MWCNTs)/Nafion was developed and applied for the extraction of polar aromatic compounds (PACs) in natural water samples. The characteristics and the application of this fiber were investigated. Electron microscope photographs indicated that the MWCNTs/Nafion coating with average thickness of 12.5 μm was homogeneous and porous. The MWCNTs/Nafion coated fiber exhibited higher extraction efficiency towards polar aromatic compounds compared to an 85 μm commercial PA fiber. SPME experimental conditions, such as fiber coating, extraction time, stirring rate, desorption temperature and desorption time, were optimized in order to improve the extraction efficiency. The calibration curves were linear from 0.01 to 10 μg mL⁻¹ for five PACs studied except p-nitroaniline (from 0.005 to 10 μg mL⁻¹) and m-cresol (from 0.001 to 10 μg mL⁻¹), and detection limits were within the range of 0.03–0.57 ng mL⁻¹. Single fiber and fiber-to-fiber reproducibility were less than 7.5 (n = 7) and 10.0% (n = 5), respectively. The recovery of the PACs spiked in natural water samples at 1 μg mL⁻¹ ranged from 83.3 to 106.0%.     

Enhanced release of itraconazole from ordered mesoporous SBA-15 silica materials

This in vitro study reports on the enhanced release of the hydrophobic drug itraconazole from the ordered mesoporous SBA-15 silica material and on the existence of a critical mesopore diameter for enhancing release.     

Methane sorption in ordered mesoporous silica SBA-15 in the presence of water

Methane or natural gas is a practical alternative fuel of vehicles. To develop more efficient technology of on-board storage, a possibility of using SBA-15 as the methane carrier is tested. An ordered mesoporous silica molecular sieve SBA-15 is synthesized aimed at collecting the data of methane sorption in the presence of water. The synthesized material is examined with SEM, TEM, and XRD analyses, and the hexagonal channel structure is confirmed. Its textual parameters are evaluated on the basis of the adsorption data for nitrogen at 77 K, and it gives the results of 802 m2/g for the specific surface area, 1.31 cm3/g for the pore volume, a narrow pore size distribution centered at 7.7 nm, and 4 nm for the width of the partition wall. Methane sorption isotherms on SBA-15 are collected with a volumetric method for samples of different contents of water, and the enhancement of the sorption capacity due to the presence of water is observed. A discussion on the mechanism of the sorption enhancement is presented.     

Temperature-programmed microwave-assisted synthesis of SBA-15 ordered mesoporous silica

The currently available microwave technology permits the development and implementation of a temperature-programmed microwave-assisted synthesis (TPMS) of ordered mesoporous silicas (OMSs). Unlike in previously reported syntheses of OMSs, in which only the final hydrothermal treatment was carried out under microwave irradiation, this work takes advantage of the existing capabilities of modern microwave systems to program the temperature and time for the entire synthesis of these materials. To demonstrate the flexibility of the proposed microwave-assisted synthesis, besides programming two consecutive steps involving initial stirring of the gel at a lower temperature and static hydrothermal treatment at a higher temperature, we explored the possibility of temperature programming of the latter step. A major advantage of microwave technology is the feasibility of temperature and time programming, which has been demonstrated by the synthesis of one of the most popular OMSs, SBA-15, over an unprecedented range of temperatures from 40 to 200 degrees C. Since the synthesis of OMSs has not yet been explored and reported at temperatures exceeding 150 degrees C, this work is focused on the SBA-15 samples prepared at higher temperatures (such as 160, 180, and even 200 degrees C). These SBA-15 samples show better thermal stability than those synthesized at commonly used temperatures either under conventional or microwave conditions. Moreover, a partial decomposition of the template during high-temperature microwave-assisted syntheses does not compromise the formation of well-ordered SBA-15 materials. This study shows that the simplicity and capability of temperature and time programming in TPMS allows one not only to tune the adsorption and structural properties of OMSs but also to easily screen a wide range of conditions in order to optimize and scale-up their preparation as well as to significantly reduce the time of synthesis from days to hours.     

Determination of organophosphorous pesticides in wastewater samples using binary-solvent liquid-phase microextraction and solid-phase microextraction: a comparative study

A simple and efficient binary solvent-based two-phase hollow fiber membrane (HFM)-protected liquid-phase microextraction (BN-LPME) technique for moderately polar compounds was developed. Six organophosphorous pesticides (OPPs) (triethylphosphorothioate, thionazin, sulfotep, phorate, disulfoton, methyl parathion and ethyl parathion) were used as model compounds and extracted from 10-mL wastewater with a binary-solvent (toluene:hexane, 1:1) mixture. Some important extraction parameters, such as extraction time, effect of salt, sample pH and solvent ratio composition were optimized. BN-LPME combined with gas chromatography/mass spectrometric (GC/MS) analysis provided repeatability (R.S.D.s ≤ 12%, n = 4), and linearity (r ≤ 0.994) and solid-phase microextraction provides comparable of R.S.D.s ≤ 13%, n = 4 and linearity (r = ≤0.966) for spiked water samples. The limits of detection (LODs) were in the range of 0.3-11.4 ng L⁻¹ for BN-LPME and 3.1-120.5 ng L⁻¹ for SPME at (S/N = 3) under GC/MS selective ion monitoring mode. In addition to high enrichment, BN-LPME also served as a sample cleanup procedure, with the HFM act as a filtering medium to prevent large particles and extraneous materials from being extracted. To investigate and compare their applicability, the BN-LPME and SPME procedures were applied to the detection of OPPs in domestic wastewater samples.     

Structure sensitivity of vibrational spectra of mesoporous silica SBA-15 and Pt/SBA-15

The vibrational properties of mesoporous silica (SBA-15) were investigated by deep ultraviolet (UV) Raman and infrared spectroscopies with and without the presence of platinum nanoparticles in the mesopores that were incorporated by sonication. Raman and IR spectral line assignments were made by comparison to amorphous silicas. This procedure permitted identification of vibrations of longitudinal (LO) and transverse (TO) optical lattice modes, the presence of Si-OH, and vibrational modes associated with the presence of three-, four-, and six-membered siloxane rings. Hydraulic pressing of the mesoporous silica with pressure in the range 3-7 tons cm(-2) destroys the X-ray diffraction pattern and strongly decreases the Raman peak (D2) associated with three-membered rings at the surface. In the presence of platinum nanoparticles in the silica mesopores, a peak attributed to a Pt-O stretching vibration appears at between 530 and 580 cm(-1) in the UV-Raman spectrum, which can be used to monitor the presence of the platinum particles and their interaction with the support. The D2 feature in the UV-Raman spectra also decreases with increasing Pt loading, which is attributed to interactions of the Pt nanoparticles with the silica surface.     

介孔涂层固相微萃取-高效液相色谱法测定水样中邻苯二羧酸酯化合物

以苯基官能化MCM-41介孔复合体作为固相微萃取(SPME)的吸附涂层, 与高效液相色谱(HPLC)联用测定了不同水样中邻苯二甲酸二甲酯(DMP)、邻苯二甲酸二乙酯(DEP)、邻苯二甲酸二丁酯(DBP)和邻苯二甲酸二辛酯(DOP)的含量, 对SPME的吸附和解吸时间、温度、搅拌速度进行了优化, 线性范围分别为1.19×10-4～119 μg/L、 1.12×10-4～112 μg/L、 1.05×10-4～105 μg/L和9.80×10-5～98 μg/L, 检出限依次为0.030、 0.027、 0.029和0.022 ng/L. 使用该方法测定了多种水样中邻苯二羧酸酯类化合物.     

Formation of titanium nitride nanoparticles within mesoporous silica SBA-15

We report the first synthesis of titanium nitride (TiN) nanoparticles inside the nanoscale channels of mesoporous silica SBA-15. The TiN precursor, Ti(NMe(2))(4) in toluene, was incorporated into the methyl group-modified channels of the SBA-15 powder. The functionalization of pore surfaces with methyl groups generates hydrophobic surfaces that facilitate impregnation with Ti(NMe(2))(4) and minimizes reactions between the TiN precursor and the hydroxyl groups on the surface of SBA-15. Formation of TiN nanoparticles inside the mesoporous channels of SBA-15 was carried out by subsequent ammonolysis at high temperatures (700-750 degrees C). The final products have been characterized by TEM and EELS images, powder XRD patterns, FTIR spectra, UV-vis absorption spectra, and nitrogen adsorption isotherm measurements to confirm the presence and distribution of TiN nanoparticles in the SBA-15 samples.     

Determination of organochlorine pesticides and their metabolites in soil samples using headspace solid-phase microextraction

An analytical procedure was developed using headspace solid-phase microextraction (HS-SPME) for the determination of organochlorine pesticides (OCPs) and their metabolites in sandy soil samples. The developed procedures involving fiber selection, temperature effect, absorption time, soil matrix and the addition of solvents of different polarity were optimized. Also, the results were compared to those achieved using Soxhlet extraction standard method. The 100-microm polydimethylsiloxane (PDMS) and 65-microm PDMS-divinylbenzene showed good extraction efficiency for 18 organochlorine pesticides. An increase in the extraction efficiency of organochlorine pesticides and the metabolites was observed when the temperature increased, and an optimum temperature of 70 degrees C for extracting OCPs was obtained. The application of other hydrophilic solvents had different effects on the extraction of organochlorine pesticides and the metabolites. Higher responses of OCPs were obtained when 5 ml of water was added to the soil. Good linearity of OCPs between 0.2 and 4 ng/g soil was observed. The relative standard deviation was found to be lower than 25%. Also the limits of detection were between 0.06 and 0.65 ng/g, which were lower than those obtained using Soxhlet extraction. Moreover, the optimized HS-SPME procedure was applied to the analysis of OCPs in certified reference material (CRM) 804-050 soil and compared with Soxhlet extraction procedure. Results obtained in this study were in good agreement with those obtained using Soxhlet extraction. The mean values obtained using HS-SPME technique were in the range of 16.5 to 1459.6 mg/kg, which corresponds to the recoveries of 68% to 127% of the certified values of CRM soil.     

Formation of indium nitride nanorods within mesoporous silica SBA-15

We report the first formation of arrays of InN nanorods inside the nanoscale channels of mesoporous silica SBA-15. In(NO3)3 dissolved in methanol was incorporated into SBA-15 powder without prior pore surface functionalization. Formation of InN nanorod arrays was carried out by ammonolysis at 700 degrees C for 8 h. The final products have been characterized by FT-IR spectra, (29)Si MAS NMR spectra, Raman spectra, XRD patterns, TEM images, nitrogen adsorption-desorption isotherm measurements, and optical spectroscopy. The freestanding InN nanorods observed after silica framework removal with HF solution show diameters of 6-7.5 nm and lengths of 25-50 nm. Formation of a trace amount of In2O3 was also verified. The InN nanorods exhibit a broad band centered at around 550-600 nm, and a band gap energy of 1.5 eV was determined. No light absorption in the near-IR region was measured. The nanorods give a weak emission band centered at around 600 nm. These optical properties are believed to be related to the possible incorporation of oxygen during InN nanorod synthesis.     

Synthesis and characterization of large-pore vinyl-functionalized mesoporous silica SBA-15

Ordered mesoporous silicas SBA-15 with high loadings of pendant vinyl groups have been synthesized via co-condensation of tetraethoxysilane (TEOS) and triethoxyvinylsilane (TEVS) templated with a triblock copolymer.