Adsorption of Poly(ethylene oxide)-Poly(lactide) Copolymers. Effects of Composition and Degradation

The effect of chemical degradation of two diblock copolymers of poly(ethylene oxide) (E) and poly(lactide) (L), E(39)L(5) and E(39)L(20), on their adsorption at silica and methylated silica was investigated with in situ ellipsometry. Steric stablization of polystyrene dispersions was investigated in relation to degradation. Hydrolysis of the poly(lactide) block of the copolymers was followed at different temperatures and pH by using HPLC to measure the occurrence of lactic acid in solution. The block copolymers were quite stable in pH-unadjusted solution at low temperature, whereas degradation was facilitated by increasing temperature or lowering of the pH. Lower degradation rates of E(39)L(20) where observed at low temperature in comparison with those of E(39)L(5), whereas the degradation rates of the copolymers were quantitatively similar at high temperature. The adsorption of the copolymers at methylated silica substrates decreased with increasing degree of degradation due to the reduction in the ability of hydrophobic block to anchor the copolymer layer at the surface. At silica the adsorption initially increased with increasing degradation, particularly for E(39)L(20) due to deposition of aggregates onto the surface. After extensive degradation the adsorption of the copolymers at both silica and methylated silica resembled that of the corresponding poly(ethylene oxide) homopolymer. Overall, it was found that the eventual reduction in adsorption occurred at a lower degree of degradation for E(39)L(5) than for E(39)L(20). Mean-field calculations showed a reduced anchoring for the block copolymers with decreasing poly(lactide) block length at hydrophobic surfaces. In accordance with this finding, it was observed that polystyrene dispersions were stabilized by E(39)L(20) or E(39)L(5) in a way that depended on both the lactide block length and the degree of degradation. Upon degradation of the hydrophobic block, stabilization of the polystyrene dispersions was maintained initially, but eventually degradation resulted in destabilization. The average residual copolymer concentration required for stabilization of the polystyrene dispersions was much higher than the corresponding concentration of intact copolymer required for stabilization. Copyright 2001 Academic Press.     

Phase behavior in mixtures of a homopolymer and a block copolymer 1. FTIR and DSC studies

Miscibility in blends of three styrene-butadiene-styrene and one styrene-isoprene-styrene triblock copolymers containing 28%, 30%, 48%, and 14% by weight of polystyrene, respectively, with poly(vinyl methyl ether) (PVME) were investigated by FTIR spectroscopy and differential scanning calorimetry (DSC). It was found from the optical clarity and the glass transition temperature behavior that the blends show miscibility for each kind of triblock copolymers below a certain concentration of PVME. The concentration range to show miscibility becomes wider as the polystyrene content and molecular weight of PS segment in the triblock copolymers increase. From the FTIR results, the relative peak intensity of the 1100 cm^-1 region due to COCH₃ band of PVME and peak position of 698 cm^-1 region due to phenyl ring are sensitive to the miscibility of SBS(SIS)/PVME blends. The results show that the miscibility in SBS(SIS)/PVME blends is greatly affected by the composition of the copolymers and the polystyrene content in the triblock copolymers. Molecular weights of polystyrene segments have also affected the miscibility of the blends. ©1995 John Wiley & Sons, Inc.     

Analysis of glass transition and relaxation processes of low molecular weight polystyrene-b-polyisoprene diblock copolymers

The objective of this study is to analyze the glass transition temperature and relaxation processes of low molecular weight polystyrene-block-polyisoprene diblock copolymers with different compositions, synthesized via anionic polymerization. Thermal properties were investigated by differential scanning calorimetry and dynamic-mechanical thermal analysis, while the morphologies at room temperature were investigated by transmission electron microscopy and small-angle X-ray scattering. The χN values indicate that the diblock copolymers lie near the weak segregation regime. Three different experimental techniques were applied to determine the dynamic properties, i.e., linear viscoelastic shear oscillations, creep recovery experiments, and dielectric spectroscopy. The rheological experiments were performed above the order–disorder transition temperature where the diblock copolymers behave like a Maxwell fluid. Our results indicate that the presence of the polyisoprene segments strongly influences the monomeric friction coefficient and the tendency to form entanglements above the order–disorder temperature. Consequently, the zero-shear rate viscosity of a diblock copolymer is much lower than the zero-shear rate viscosity of the neat polystyrene block (the polystyrene precursor of the polymerization procedure). Dielectric spectroscopy enables the analysis of relaxation processes below the glass transition of the polystyrene microphase. Frequency sweeps indicate the dynamic glass transition of the polyisoprene blocks, which are partly mixed with the polystyrene blocks, which are always the majority component in the block copolymers of this study.     

Towards quantification of butadiene content in styrene-butadiene block copolymers and their blends with general purpose polystyrene (GPPS) and the relation between mechanical properties and NMR relaxation times

The properties of styrene-butadiene-styrene (SBS) block copolymers do not only depend on the butadiene content and the degree of polymerisation but also on their chain architecture. In this contribution we present the results of a low-field time domain (TD) NMR study in which the transverse relaxation behaviour of different SBS block copolymers was analysed and correlated with findings from mechanical testing on pure and blended materials and transmission electron microscopy data which provide information on the microphase separation.The results indicate that while a straightforward determination of the butadiene content as in blended materials like ABS is not possible for these materials, the TD-NMR results correlate quite well with the mechanical performance of blends from SBS block copolymers with general purpose polystyrene (GPPS), i.e. industrial grade homopolymer polystyrene. Temperature-dependent experiments on pure and blended materials revealed a slight reduction in the softening temperature of the GPPS fraction in the blends.     

The synthesis and characterization of organometallic copolymers with Mn-Re binuclear transition-metal group in the side chain

Novel organometallic copolymers with Mn-Re binuclear transition-metal groups in the side chain are synthesized and characterized. The structure and properties of the copolymers are characterized by GPC, DSC, TG, NMR, FT-IR, UV-Vis spectra and elemental analysis. The glass transition temperature and UV-Vis spectra properties of these three organometallic copolymers are found to be different from the normal polystyrene. New synthetic strategy for the synthesis of or-ganometallic copolymer is developed.     

Poly(styrene-block-isoprene) nanocomposites: Kinetics of intercalation and effects of copolymer on intercalation behaviors

In addition to phase morphology, diffusion, and dynamics in the bulk, the behavior of block copolymers in the confined state has been of great interest. Although random and graft copolymers have been used in polymer-layered silicate nanocomposites, well-defined block copolymers have received relatively little attention. In this study, the kinetics of intercalation of a series of poly(styrene-b-isoprene) block copolymers into a layered silicate were examined via X-ray diffraction. Intercalation was observed even when the copolymer was in the ordered state, with no discontinuity around the order–disorder transition of the copolymer. As the size of the polystyrene block was increased, slower intercalation kinetics were observed, possibly because of the increased glass-transition temperature of the polystyrene segment. Finally, the clearing temperature of the copolymer in the nanocomposites as measured by small-angle X-ray scattering showed a large heating-rate dependence suggesting that the nanoparticles act as kinetics barriers to the disordering of the copolymer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 3264–3271, 2003     

Etude de la reaction d'addition de polystyrenes ω-vinylsilane avec une molecule-modele des α,ω-dihydrogeno-polydimethylsiloxanes

Three-block copolymers polystyrene-polydimethylsiloxane-polystyrene can be obtained by a hydrosilylation reaction between α,ω-dihydrogeno polydimethylsiloxane and ω-vinylsilane polystyrene molecules.The purpose of the present investigation was to establish by use of a model system, the optical conditions for the synthesis of three-block and multiblock copolymers: reaction temperature and concentrations of reactants and catalyst.     

Surface properties of styrene–ethylene oxide block copolymers

Hydrophobic–hydrophilic block copolymers were prepared by “living” anionic polymerization. They consist of polystyrene and poly(ethylene oxide) blocks, and are soluble in water. Their interfacial properties were investigated, employing aqueous solutions. The block copolymers lowered the surface tension of water in analogy with the low molecular weight surfactants such as sodium lauryl sulfate and heptaethylene oxide n-dodecyl ether. Their aqueous solutions exhibited solubilization properties differing from those of polyethylene glycol. Therefore, it is thought that the polystyrene blocks produce solubilization phenomena. In samples of the same styrene content, the precipitation temperature of a high molecular weight copolymer in water was lower than that of a low molecular weight copolymer at the same concentration in the same solvent. The surface tension and precipitation temperature of aqueous solutions seem to be influenced by molecular weight and composition.     

Synthesis of new smectic C* liquid-crystalline block copolymers

A series of smectic C^* liquid-crystalline (LC) block copolymers were successfully synthesized via the living anionic polymerization of polystyrene with optically active methacrylate monomers containing (S)-2-methylbutyl 4-(4-hydroxyphenylcarbonyloxy)-biphenyl-4′-carboxylate mesogens. These materials are the first reported smectic C^* block copolymers. Anionic polymerization in tetrahydrofuran (THF) at −70°C leads to LC block molecular weights of approximately twenty repeating units. The number-average molecular weight of the polystyrene block was varied from 7000 to 20000 to adjust the composition in the block copolymers. Differential scanning calorimetry and optical microscopy indicate that the smectic C^* phase is present in the systems over broad temperature ranges.     

On the macro- and microphase separation of compatibilizers in immiscible polymer blends

Macro- and microphase separation of compatibilizing graft copolymers in melt-mixed polystyrene/polyamide-6 blends was studied by transmission electron microscopy and thermal analysis. Three different graft copolymers with main chains of polystyrene and side chains of poly(ethylene oxide) were used as additives at various concentrations. The polyamide-6 domain sizes decreased with increasing amounts of compatibilizing graft copolymers in the blends up to a saturation concentration, after which no further reduction was noted. Macrophase separation of the graft copolymers into discrete macrodomains 20–200 nm in size occurred at concentrations equal to or slightly lower than the saturation concentration. The macrodomains of the graft copolymers were microphase separated, and the sizes and shapes of the microdomains were found to largely depend on the graft copolymer structure and composition. As a consequence of microphase separation, poly(ethylene oxide) crystallinity was noted in blends with sufficiently high macrophase contents. Observations of a graft copolymer interphase between the polystyrene matrix and the polyamide-6 domains confirmed that the graft copolymer was present at the blend interfaces in some of the compatibilized blends. © 1996 John Wiley & Sons, Inc.     

Dynamic mechanical relaxation behavior of block copolymers at high temperatures

We carried out dynamic mechanical measurements to investigate three different examples of block copolymers: styrene–isoprene diblock copolymers and styrene–butadiene–styrene and styrene–(styrene butadiene)–styrene triblock copolymers. Isochronal and isothermal measurements of the real and imaginary parts of the complex shear modulus were performed over wide ranges of temperature and frequency. The measurements showed the presence of an additional relaxation process appearing at temperatures higher than those of the glass relaxation of the polystyrene phase, which has been misinterpreted by some authors as an order–disorder transition. The frequency dependence revealed that this process was a relaxation process and did not belong to a first‐order transition. Moreover, the influence of crosslinking via dicumylperoxide was measured, and we constructed complete master curves to confirm the presence of two relaxation processes. The high‐temperature relaxation process was strongly suppressed by crosslinking. Therefore, it was possible to detect the glass relaxation process of the polystyrene phase in a precise manner. The results were compared with those of homopolymers. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2198–2206, 2001     

聚苯乙烯-b-聚硅氧烷-b-聚苯乙烯三嵌段共聚物的合成及表征

采用乙烯基封端的聚 (二甲基硅氧烷 )与溴化氢反应制得末端含有C Br的双官能聚 (二甲基硅氧烷 ) ,以此聚 (二甲基硅氧烷 )大分子为引发剂 ,CuCl为催化剂 ,4 ,4′ 二 (5 壬基 ) 2 ,2′ 联吡啶为配体 ,通过原子转移自由基聚合法 ,制得分子量和结构可控的聚苯乙烯 b 聚硅氧烷 b 聚苯乙烯 (PSt b PDMS b PSt)共聚物 .     

Analysis of polystyrene-b-polyisoprene copolymers by coupling of liquid chromatography at critical conditions to NMR at critical conditions of polystyrene and polyisoprene

For the investigation of the molecular heterogeneity of polystyrene-b-polyisoprene block copolymers, a chromatographic separation method, namely liquid chromatography at critical conditions was developed. This method was coupled on-line with (1)H-NMR(where NMR stands for nuclear magnetic resonance) for the comprehensive analysis of the polystyrene-b-polyisoprene copolymers. The copolymers were synthesized by two different methods: sequential living anionic polymerization and coupling of living precursor blocks. While (1)H-NMR allows just for the analysis of the bulk chemical composition of the block copolymers, the coupling with liquid chromatography at critical conditions provides selective molar mass information on the polystyrene and polyisoprene blocks within the copolymers. The polyisoprene block molar mass is determined by operating at chromatographic conditions corresponding to the critical point of adsorption of polystyrene and size exclusion chromatography mode for polyisoprene. The molar mass of the polystyrene block is determined by operating at the critical conditions of polyisoprene. In addition to the molar mass of each block of the copolymers, the chemical composition distribution of the block copolymers was determined. By using the coupling of liquid chromatography at critical conditions to (1)H-NMR, one can also detect the homopolymers formed during synthesis. Finally the microstructure of the polyisoprene block in the copolymers was evaluated as a function of molar mass.     

The thermal decomposition of hydrocarbon copolymers-IV Kinetics of decomposition of copolymers incorporating styrene

The kinetics of thermal decomposition of a series of copolymers of structure with n = 0, 1, 3, 4 and 5 have been studied. Activation energies have been evaluated and used to compare the stabilities of the various copolymers with polyethylene and polystyrene. It was found that the apparent order of the overall decomposition reaction (as studied by weight-loss measurements) varied with conversion and temperature. It is concluded that the mechanism of thermal breakdown is complex.     

Glass transition temperature of low molecular weight styrene–isoprene block copolymers

Different series of poly(styrene–isoprene) diblock and poly(styrene–isoprene–styrene) triblock copolymers were prepared. In each series, the low molecular weight polystyrene block was kept constant, and the molecular weight of the polyisoprene block varied. The glass transition behavior of these polymers was studied and their glass transition temperatures compared with those of the random copolymers of styrene and isoprene. It is concluded that some low molecular weight styrene-isoprene block copolymers form a single phase. Krause's thermodynamic treatment of phase separation in block copolymers was applied to the data. One arrives at a polystyrene–polyisoprene interaction parameter χ1,2 ≈ 0.1. The experimental and theoretical limitations of this result are discussed.     

Preparation de promoteurs azoiques macromoleculaires par voie anionique. Application a la synthese de copolymeres sequences

Polystyrene containing azo groups was prepared by deactivating anionic polystyrene with azobisisobutyronitrile. The influences of temperature and of the terminal carbanion were examined. The coupling of polystyrene chains through azo functions was greatest by using χ-methylstyrene or 1,1-diphenyl-ethylene terminal carbanions. These polymeric initiators were used to start the free radical polymerizations of methylmethacrylate and vinyl chloride. The formation of block copolymers was shown by fractionation of the reaction mixture.     

Diffusion and distribution of stable nitroxyl radicals in diene-styrene block copolymers

A method for studying the distribution and migration of additives between the phases of heterophase polymers has been developed. It is based on a photochemical reaction which selectively affects the additive contained in the phase with higher reactivity, thus sharply decreasing additive concentration in this phase. This method was used for studying the distribution of stable nitroxyl radicals between the phases of butadiene- or isoprene-styrene block copolymers and for determining diffusion coefficients of nitroxyl radicals in the polystyrene phase in the room temperature region. Diffusion coefficients for 2,2,6,6-tetramethylpiperidyl-l-oxyl in polystyrene and polybutadiene phases were also determined based on desorption curves for this radical.     

Dipole moments of (styrene-p-chlorostyrene) triblock copolymers in solutions

(Styrene-p-chlorostyrene) triblock copolymers of the ABA and BAB types (A—polystyrene; B—poly-p-chlorostyrene) were prepared by anionic polymerization and their conformational behaviours in solutions were studied from measurements of the dipole moments. Two solvents, toluene and cumene, were used for the study; toluene is a good solvent for both polystyrene and poly-p-chlorostyrene whereas cumene is a selective solvent, good for polystyrene but poor for poly-p-chlorostyrene. It was found that the dipole moments of the block copolymers measured in toluene are the same for the ABA and BAB copolymers; in cumene however the dipole moment of the BAB copolymer is smaller than that of the ABA copolymer. The results give an additional support to our previous conclusion that the conformation of the block copolymers in a good solvent such as toluene could be approximated with a pseudo-random coil form; in a selective solvent, however, some anomalies take place in the conformation of the block copolymers, as deduced from intrinsic viscosity, osmotic pressure and light scattering measurements.     

Study of molecular motion of block copolymers in solution by high-resolution proton magnetic resonance

Molecular motions of hydrophobic–hydrophilic water-soluble block copolymers in solution were investigated by high-resolution proton magnetic resonance (NMR). Samples studied include block copolymers of polystyrene–poly(ethylene oxide), polybutadiene–poly(ethylene oxide), and poly(ethylene oxide)–poly(propylene oxide)–poly(ethylene oxide). NMR measurements were carried out varying molecular weight, temperature, and solvent composition. For AB copolymers of polystyrene and poly(ethylene oxide), two peaks caused by the phenyl protons of low-molecular-weight (M?_n = 3,300) copolymer were clearly resolved in D₂O at 100°C, but the phenyl proton peaks of high-molecular-weight (M?_n = 13,500 and 36,000) copolymers were too broad to observe in the same solvent, even at 100°C. It is concluded that polystyrene blocks are more mobile in low-molecular-weight copolymer in water than in high-molecular-weight copolymer in the same solvent because the molecular weight of the polystyrene block of the low-molecular-weight copolymer is itself small. In the mixed solvent D₂O and deuterated tetrahydrofuran (THF-d₈), two peaks caused by the phenyl protons of the high-molecular-weight (M?_n = 36,000) copolymer were clearly resolved at 67°C. It is thought that the molecular motions of the polystyrene blocks are activated by the interaction between these blocks and THF in the mixed solvent.     

SIS的正电子湮没寿命谱的研究

用正电子湮没技术,在-80°～100℃温度范围内,测量了苯乙烯-异戊二烯-苯乙烯三嵌段聚合物(SIS)的正电子寿命谱。在长寿命成分的温度谱中,实验发现除了有和聚异戊二乙烯及聚苯乙烯的玻璃化温度相对应的温度转变区外,在37℃还存在一个温度转变区。这个中间转变温度可以解释为SIS嵌段共聚物的中间相的玻璃化转变温度。