Phase equilibria up to the solidus line in the V2O5−Cr2(MoO4)3 system

Phase equilibria being established in the subsolidus area of the V₂O₅?Cr₂(MoO₄)₃ system at the whole component concentration range have been studied basing on DTA and X-ray phase powder diffraction. It has been established that the system is not a real two-component system in the subsolidus area. The fact has been proved by the presence of fields in that area, where three solid phases remain in mutual equilibrium.     

Solid-state phase equilibria in the V2O5−Fe8V10W16O85 system

Phase equilibria being established in the solid state in the system V₂O₅?Fe₈V₁₀W₁₆O₈₅ were examined by X-ray phase powder diffraction and DTA. It has been found that the system of interest is a real two-component system with an eutectic temperature 620±5°C.     

Phase relations in the CoO–V<Subscript>2</Subscript>O<Subscript>5</Subscript>–Fe<Subscript>2</Subscript>O<Subscript>3</Subscript> system in subsolidus area

Thermal properties of Co₂FeV₃O₁₁ have been reinvestigated. It has been proved that this compound does not exhibit polymorphism. It melts incongruently at the temperature of 770±5°C and the phase with lyonsite type structure is the solid product of this melting. Phase relations in the whole subsolidus area of the CoO–V₂O₅–Fe₂O₃ system have been determined. The solidus area projection onto the component concentration triangle plane of this system has been constructed using the DTA and XRD methods. 15 subsidiary subsystems can be distinguished in this system.     

Calorimetric Investigations of Some Phases in the System Sodium Fluoride - Aluminium Fluoride

Beside the two well-known minerals cryolite, Na₃AlF₆, and chiolite, Na₅Al₃F₁₄, the binary system NaF-AlF₃ also contains a third compound, NaAlF₄, sodium tetrafluoroaluminate. Solid NaAlF₄ has been prepared from its vapour under controlled conditions. The stability of NaAlF₄ has been investigated by differential scanning calorimetry. It is shown that the disproportionation of the compound: 5NaAlF_4(s)=Na₅Al₃F_14(s)+2AlF_3(s) takes place at considerable rate between 700 and 900 K. The enthalpy of this reaction is calculated and found to be -66.9 kJ. Enthalpies of the two solid state transitions α-Na₃AlF₆ → β-Na₃AlF₆ and α-AlF₃ → β-AlF₃ have also been measured and new values are reported. The enthalpy of formation of chiolite, Na₅Al₃F₁₄, at 900 K has been recalculated from enthalpy increment data obtained by drop calorimetry. A value of ΔH₉₀₀ ^o = -7513.6±12.0 kJ mol^-1 has been obtained. This value is in disagreement with the recommended value given in JANAF Thermochemical Tables given at 900 K ΔH_f ^o = -7559.2 kJ mol^-1. This revised version was published online in July 2006 with corrections to the Cover Date.     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

Solid solubility of Yb2Si2O7 in β-, γ- and δ-Y2Si2O7

This paper examines the structural changes with temperature and composition in the Yb₂Si₂O₇-Y₂Si₂O₇ system; members of this system are expected to form in the intergranular region of Si₃N₄ and SiC structural ceramics when sintered with the aid of Yb₂O₃ and Y₂O₃ mixtures. A set of different compositions have been synthesised using the sol-gel method to obtain a xerogel, which has been calcined at temperatures between 1300 and 1650 °C during different times. Isotherms at 1300 and 1600 °C have been analysed in detail to evaluate the solid solubility of Yb₂Si₂O₇ in β-Y₂Si₂O₇ and γ-Y₂Si₂O₇. Although Yb₂Si₂O₇ shows a unique stable polymorph (β), Yb³⁺ is able to replace Y³⁺ in γ-Y₂Si₂O₇ and δ-Y₂Si₂O₇ at high temperatures and low Yb contents. IR results confirm the total solid solubility in the system and suggest a constant SiOSi angle of 180° in the Si₂O₇ unit across the system. The temperature-composition diagram of the system, obtained from powder XRD data, is dominated by the β-RE₂Si₂O₇ polymorph, with γ-RE₂Si₂O₇ and δ-RE₂Si₂O₇ showing reduced stability fields. The diagram is in accordance with Felsche's diagram if average ionic radii are assumed for the members of the solid solution at any temperature, as long as the β-γ phase boundary is slightly shifted towards higher radii.     

Etude de phosphates condenses diagramme d’equilibre du systeme AgPO3−Pr(PO3)3 Données sur AgPr(PO3)4

The AgPO₃?Pr(PO₃)₃ system has been studied for the first time by differential thermal analysis, X-ray diffraction and IR spectroscopy. The system shows one compound AgPr(PO₃)₄ which melts in a peritectic decomposition at 1069 K. An eutectic appears at 761 K. AgPr(PO₃)₄ belongs to the monoclinic system with space group P2_t/c,Z=4. The parameters of the unit cell are:a=12.000(9),b=13.177(4),c=7.046(5) Å and β=123^o,81(6),Z=4. Its IR absorption spectrum is typical of chain phosphates.     

Ca2+-Mg2+-Zn2+体系在水溶性聚磷酸铵溶液中螯合规律的研究

近年来,水溶性聚磷酸铵在液体肥料和复合肥料的领域受到了广泛的关注,并在发达国家中得到了大面积的推广及应用。在pH值为5.5~8.0、温度为278.15 K~323.15 K的条件下,本文采用滴定法研究Ca_²⁺-Mg_²⁺-Zn_²⁺体系在聚磷酸铵溶液中的螯合规律。实验结果表明：相同质量分数的聚磷酸铵溶液对金属离子的螯合量会随着体系中Ca_²⁺、Mg_²⁺、Zn_²⁺的摩尔浓度的变化而变化;随着温度的升高而逐渐降低;随着pH的增加而逐渐增加;随着聚合度的升高而逐渐增加。采用傅里叶红外光谱对聚磷酸铵和A₁B₃C₃体系的螯合物进行表征。     

Cubic perovskite-related phases in the ternary SrO-CuO-Nb2O5 system

A careful phase analysis study of cubic perovskite-related phases in the ternary SrO-CuO-Nb₂O₅ system has been carried out via the synthesis and compositional analysis of a range of specimens within the ternary SrO-CuO-Nb₂O₅ system. Powder XRD in conjunction with electron probe microanalysis (EPMA) has been used to determine whether the synthesized specimens are single phase or not and to determine the compositions of the various reaction products. Three quite distinct such solid solution phases have been found and their quite distinct electrical and diffraction characteristics investigated.     

The system Y2O3−MgO−P2O5

The previously unknown ternary system Y₂O₃?MgO?P₂O₅ has been examined by thermal, X-ray and microscopic methods. Its phase diagram has been determined over the composition range: YPO₄?Mg₃(PO₄)₂?Mg(PO₃)₂?Y(PO₃)₃. In the system, the existence of two mixed phosphates: MgYP₃O₁₀ and MgY(PO₃)₅ has been found, and they occur, according to their composition, at the sections YPO₄?Mg(PO₃)₂ and Y(PO₃)₃?Mg(PO₃)₂, respectively.     

Characterization of an all Sol-Gel Electrochromic Device WO3/Ormolyte/CeO2-TiO2

Electrochemical lithium intercalation in thin films of CeO₂-TiO₂ and WO₃, prepared by the sol-gel technique was investigated with cyclic voltammetry and spectroelectrochemical techniques in propylene carbonate solutions. A solid state system having the configuration WO₃/Ormolyte/CeO₂-TiO₂ has been assembled. The solid electrolyte, an organically modified electrolyte (ormolyte), was prepared with different [O]/[Li] ratios. The transmittance variation of this system during a potentiostatic step from –0.7 V to 0.8 V was about 35% at 550 nm.     

Subsolidus area of the system CdO - V2O5 - Fe2O3

Phase diagrams in the subsolidus area of the systems FeVO₄ - CdO and FeVO₄ - Cd₂V₂O₇ have been deduced using the results of XRD and DTA analyses. On the basis of these diagrams and some additional verifying research, a projection of the subsolidus area of the CdO - V₂O₅ - Fe₂O₃ system onto the plane that comprises the components’ concentration triangle has been presented. The H-type phase is the only phase formed in this system. It co-exists at equilibrium with other phases in six subsidiary subsystems.      

Phase equilibria in the solid state in the V9Mo6O40-Cr2O3 system

Phase equilibria have been established in the solid state in the V₉Mo₆O₄₀-Cr₂O₃ system. The results obtained have permitted to state that the system of interest, in the subsolidus area, is not a real two-component system in the whole component concentration range.

---

Zusammenfassung Im Festzustand des Systemes V₉Mo₆O₄₀-Cr₂O₃ wurden Phasengleichgewichte ermittelt. Die erhaltenen Resultate lassen darauf schließen, daß das fragliche System im Subsolidus-Gebiet über den gesamten Konzentrationsbereich kein reelles Zweikomponentensystem ist.

     

Determination of heats of aluminothermic redox reaction of V2O5 and MnO2

Differential thermal analysis has been used for quantitative determination of heats of aluminothermic redox reaction of MnO₂ and V₂O₅ over a wide range of temperatures. Heat of reaction V₂O₅?Al and MnO₂?Al systems have been determined using the calibration plot established. The experimentally determined values compare well with those predicted from thermodynamic data available in the literature. It has been found that V₂O₅?Al system involves a higher heat of reaction in comparison to the MnO₂?Al system.     

The pyrochlore to ‘defect fluorite’ transition in the Y2(ZryTi1−y)2O7 system and its underlying crystal chemistry

A careful investigation of the previously reported single phase, pyrochlore structure type Y₂(Zr_yTi_1−y)₂O₇, 0?y?0.9, (YZT) solid solution has been carried out. Given the known slow rate of diffusion of cations in fluorite-related stabilized zirconia systems and the consequent difficulty in achieving equilibrium, careful attention was paid to synthesis procedures while Guinier XRD and electron diffraction were used to investigate the synthesized materials. As a consequence, a subtle but nonetheless clear two-phase region separating a pyrochlore-type solid solution field (from 0?y?∼0.54) from a “defect fluorite” type solid solution field (from ∼0.68?y?1) has been found. The underlying crystal chemistry of the system has been investigated using the bond valence sum approach. The dielectric properties have also been measured as a function of composition. The dielectric constant and dielectric loss of the lowest y compounds are potentially quite useful but deteriorate rapidly with increasing Zr content.     

Study on Phase Relations in Zn3V2O8–ZnMoO4 System

The phase equlibria established in the Zn₃V₂O₈–ZnMoO₄ system over the whole component concentration range up to 1000°C have been investigated. A phase diagram has been constructed using the results of DTA and XRD methods. This revised version was published online in July 2006 with corrections to the Cover Date.     

General Route to Synthesize Monodisperse Oxide (Hydroxide) Nanoparticles

Mono-dispersed oxide and hydroxide nanoparticles have been synthesized through the solvothermal process in alcohol-water mixtures. The products were characterized by powder x-ray diffraction (XRD) and scanning electron microscopy (SEM). Plate-like nanoparticles are obtained for Bi₂O_2.33, Fe₂O₃, and Cd(OH)₂, and spherical nanoparticles are obtained for SnO₂. The growth mechanism for the mono-dispersed nanoparticles has been preliminarily discussed.     

A simple PdCl2/O2/DMF catalytic system for highly regioselective cyclotrimerization of olefins with electron-withdrawing groups

A highly regioselective cyclotrimerization of olefins with electron-withdrawing groups in a PdCl₂/O₂/DMF catalytic system is disclosed, and a possible mechanism has also been proposed, which reveals the PdCl₂-catalyzed cyclotrimerization of olefins with electron-withdrawing groups goes through a quite different pathway from that of alkynes.     

Diagramme de phases du systeme binaire LiNO3-NaNO3

Phase diagram of the binary system LiNO₃-NaNO₃ has been obtained by using direct and differential thermal analysis between 323 and 623 K. This system is characterized by an eutectic plateau at 467 K. The eutectic point is at 0.465 mole NaNO₃. A peritectic appears at 550 K. There is no miscibility in the solid state. These findings associated with some other thermodynamic results have been used to calculate the activities of the constituents along the liquids curve and the excess thermodynamic functions at 618 K. The constituents seem not to have a symmetrical influence on the thermodynamic quantities.

     

A new, efficient and simple method for the thionation of ketones to thioketones using P4S10/Al2O3

A simple, efficient and new method has been developed for the synthesis of thioketones by thionation of ketones using P₄S₁₀/Al₂O₃ in acetonitrile. It has been found that the P₄S₁₀/Al₂O₃ combination provides a simple and convenient method for the synthesis of thioketones.