碳纳米管修饰电极检测特丁基对苯二酚

利用碳纳米管修饰玻碳电极(MWCNTs/GCE),对特丁基对苯二酚(TBHQ)进行了检测,采用循环伏安法(CV)和差分脉冲伏安法(DPV)考察了TBHQ在裸电极和修饰电极上的电化学行为。M WCNTs/GCE对TBHQ的氧化具有较好的电催化活性,在修饰电极上的氧化还原峰电位差从261 m V减小到30 m V。在0.10 mol/L磷酸盐缓冲溶液(p H 7.0)中,扫速为50 m V/s时,此修饰电极的DPV响应与TBHQ浓度在2~250μmol/L范围内呈线性关系,检出限为0.1μmol/L(S/N=3)。此修饰电极可应用于食用油中TBHQ的测定,回收率为92.0%~104.0%。     

基于纳米二氧化锆与铂微粒复合修饰玻碳电极的甲醛传感器研究

采用循环伏安法在玻碳电极表面依次电沉积纳米二氧化锆和铂微粒,制备了一种检测甲醛的新型电化学传感器。用电镜扫描对该修饰电极表面进行了表征,循环伏安法和线性扫描伏安法研究了甲醛在该修饰电极上的电催化氧化作用,优化了实验参数。结果表明,该修饰电极对甲醛有很好的电催化氧化作用,在0.1 mol/L H2SO4溶液中,甲醛的氧化峰电流与其浓度在1.0×10-6~5.0×10-3mol/L范围内呈良好线性关系,回归方程为Ip(μA)=79.95+2.005×105c(mol/L),相关系数r=0.999 3,检出限为5.0×10-7mol/L。     

基于氧化锆/石墨烯复合材料修饰电极测定亚硝酸根

用水热法制备了氧化锆(ZrO2)/石墨烯(GR)复合材料,采用循环伏安法研究了NO-2在ZrO2/GR/GCE上的电化学行为。ZrO2/GR/GCE对NO-2的氧化具有明显的电催化作用。利用示差脉冲伏安法测定NO-2,NO-2的氧化峰电流与其浓度在4.8×10-7~9.0×10-4mol/L范围内呈现良好的线性关系,检出限为7.8×10-8mol/L(S/N=3)。     

二氧化硅/金复合膜修饰玻碳电极用于双酚A的检测

该文制备了二氧化硅/金复合膜修饰玻碳电极(SiO_2/Au/GCE),提出了一种简便检测双酚A(BPA)的电化学分析方法。采用扫描电镜(SEM)和红外光谱(FT-IR)对SiO_2和SiO_2/Au的形貌和结构进行了表征,循环伏安法(CV)和交流阻抗法(EIS)研究了SiO_2/Au/GCE的表面电化学特性,同时用CV、计时库仑法(CC)、控制电位电解库仑法、线性扫描伏安法(LSV)和差分脉冲伏安法(DPV)等研究了BPA在SiO_2/Au/GCE上的电化学行为,优化了实验参数,并得到电化学动力参数。实验发现:SiO_2/Au/GCE对BPA具有良好的电催化活性,BPA在该修饰电极上的氧化峰电流为GCE上的3倍,且BPA在SiO_2/Au/GCE上的氧化过程为2电子2质子的完全不可逆电极过程。在最佳条件下,BPA的氧化峰电流分别在0.01~0.50μmol/L和0.50~25μmol/L浓度范围内呈良好的线性关系,检出限为1.9×10-8mol/L。用于一次性手套中BPA含量的测定,回收率为98.9%~105.3%,与高效液相色谱法(HPLC)进行对照,结果满意。     

原位氮掺杂石墨烯修饰电极同时检测苯二酚3种异构体

利用多巴胺的聚合及还原特性,制备聚多巴胺包覆还原氧化石墨烯,在氮气保护下煅烧,制得氮原位掺杂石墨烯(C/N-Graphene)。应用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外(FT-IR)光谱表征该复合物的形貌和结构。应用滴涂及Nafion膜固定法制备C/N-Graphene修饰玻碳电极(C/N-Graphene/GCE)。该修饰电极对苯二酚3种异构体的氧化反应表现出优异的电催化性能和选择性,差分脉冲伏安法(DPV)峰电流与对苯二酚(HQ)、邻苯二酚(CC)、间苯二酚(RC)的浓度呈良好的线性关系,其线性范围分别为0.5~1 000μmol/L、0.5~460μmol/L和0.1~580μmol/L,检出限分别为0.251μmol/L、0.144μmol/L和0.072μmol/L。该方法应用于药厂废水和江水检测,3种苯二酚异构体回收率为97.0%~103.0%,相对标准偏差(RSD)小于5%(n=5),结果表明C/N-Graphene/GCE修饰电极适用于污染水样的快速检测。     

氧化钕-单壁碳纳米管修饰玻碳电极对鸟嘌呤和腺嘌呤的电催化氧化

制备了氧化钕-单壁碳纳米管修饰玻碳电极(Nd2O3-SWNTs/GCE)。采用循环伏安法(CV)探究了鸟嘌呤(G)和腺嘌呤(A)在该修饰电极上的电化学行为。结果表明:该修饰电极对G和A的氧化具有良好的电催化能力。在最佳条件下,用示差脉冲伏安法(DPV)对G和A进行检测,其氧化峰电流与浓度分别在10~50μmol/L范围内呈现良好的线性关系,检出限(S/N=3)均为5.0×10-8 mol/L。该修饰电极可以用来同时测定DNA中的G和A。     

对硫磷在纳米氧化铝薄膜修饰电极上的电化学行为及其测定

制备了纳米氧化铝修饰玻碳电极(nano-Al2O3/GCE/CME),用循环伏安法(CV)、线性扫描伏安法(LSV)研究了对硫磷(TP)在nano-Al2O3/GCE/CME上的电化学行为.实验表明,该修饰电极与裸电极相比能显著提高TP的氧化还原峰电流并降低其氧化峰电位.在0.1 mol/L HAc-NaAc缓冲溶液(pH =5)中,TP在该修饰电极上产生1个不可逆的还原峰( Epc1=-0.567 V)和1对可逆氧化还原峰( Epa2=0.018 V和Epc2=-0.008 V) ,氧化峰电流与TP的浓度在2.5×10-9～1.0×10-7 mol/L和1.0×10-7～1.0×10-5 mol/L范围内具有良好的线性关系,回归方程分别为: ip(μA)=0.2529+4.201C(μmol/L), r=0.9984和ip(μA)=0.6752+0.3181C(μmol/L), r=0.9946.开路富集30 s后,检出限为1.0 ×10-9 mol/L(S/N=3).在1.0×10-5 mol/L TP试液中连续测定10次,其RSD为3.8%.用此方法测定了蔬菜中TP的含量,回收率为95. 6%～100.5% ,结果满意.     

8-羟基脱氧鸟苷在壳聚糖/石墨烯修饰电极上的电化学及DNA氧化损伤检测

采用循环伏安(CV)、线性扫描伏安(LSV)和示差脉冲伏安(DPV)等方法研究了8-羟基脱氧鸟苷(8-OHdG)在壳聚糖(Chi)/石墨烯(GR)修饰的玻碳电极(GCE)上的电化学行为,8-OHdG在该修饰电极上氧化峰电流与其浓度在3.5×10-7~1.4×10-4mol/L范围内呈良好的线性关系,检测限为6.4×10-8mol/L(S/N=3)。将Chi/GR/GCE用于检测DNA氧化损伤,8-OHdG在修饰电极上的氧化峰电流与损伤的DNA质量浓度在10~300 mg/L范围内呈良好的线性关系,损伤DNA检出限为0.026 mg/L(S/N=3)。     

纳米金/Nafion/石墨烯修饰玻碳电极检测对苯二酚的研究

采用一步电化学共还原的方法将纳米金(AuNPs)、Nafion、电化学还原石墨烯(ERGO)修饰到玻碳电极(GCE)表面,制成修饰电极AuNPs/Nafion/ERGO/GCE。以扫描电镜对其进行表征,用循环伏安法和微分脉冲伏安法研究对苯二酚在该修饰电极上的电催化行为。优化了实验参数,对苯二酚在2.0～100μmol/L及100～800μmol/L浓度范围内与其氧化峰电流呈良好的线性关系,检出限为0.3μmol/L。用该修饰电极成功地进行了实际水样中对苯二酚含量的测定。     

立方体银纳米-聚二烯二甲基氯化铵/氧化石墨烯复合膜修饰电极用于多巴胺和亚硝酸根的同时检测

以聚二烯二甲基氯化铵( PDDA)为保护剂和还原剂,制备了PDDA功能化的银纳米颗粒( AgNPs),然后与氧化石墨烯( GO)复合,得到 PDDA功能化的立方体银纳米( C-AgNPs)/GO 复合膜,修饰于玻碳电极( GCE)表面,形成C-AgNPs-PDDA/GO/GCE。采用扫描电子显微镜表征了不同修饰膜的形貌,探讨了其对多巴胺( DA)和亚硝酸根( NO-2)的循环伏安行为,发现C-AgNPs-PDDA/GO复合膜对DA和NO-2表现出显著的电催化氧化活性。采用差分脉冲伏安法,修饰电极检测DA的线性范围为0.030~0.300μmol/L和0.300~300μmol/L,检测 NO-2的线性范围为30.0~2300μmol/L,检测下限分别为9.8 nmol/L 和12.6μmol/L (S/N=3)。此电极具有良好的抗干扰性、重现性和稳定性,可用于人体血清样品中DA和NO-2的同时测定,回收率分别为97.4%~104.2%和98.0%~102.8%。与分光光度法比较,两者测定结果一致。     

The Colloidal Stabilization of Carbon with Carbon: Carbon Nanobubbles as both Dispersant and Glue for Carbon Nanotubes

The superior physical properties of carbon nanotubes (CNTs) have led to their broad application. Intrinsically, CNTs tend to agglomerate from hydrophobic interactions, which is highly undesirable for solution processing and device fabrication. Commonly, a stabilizer consisting of organic surfactants or polymers is used to disperse CNTs. Recently, we synthesized nitrogen‐doped carbon hollow nanospheres (25–90 nm), termed carbon “nanobubbles”. They bear superior dispersability in water and distinctive graphitic order. Herein, we describe the nanobubble‐assisted dispersion of CNTs in aqueous solution upon sonication. This process relies on the π–π interaction between the two aromatic carbon nanostructures, which can process their carbon mixture in water into conductive filter membranes, ink, and discs. This stabilization can be extended to other aromatic carbons. In addition, the π–π interaction may create a new type of carbon p–n junction that can be used to improve charge separation.     

一维新型碳的同素异形体:碳链

碳链是一种完全一维的、具有电子轨道sp杂化结构的新型碳的同素异形体.正是由于碳链的独特的一维结构,使其拥有区别于富勒烯、石墨烯和碳纳米管的化学键,从而表现出更加优异的性能,如:理论预言碳链的机械强度是石墨烯的几倍;碳链的导热也类似于石墨烯和碳纳米管;碳链是具有直接带隙的半导体材料,且带隙的大小可以通过其长度来调控,其长...     

Adsorption of Carbon Dioxide on Activated Carbon

The adsorption of CO2 on a raw activated carbon A and three modified activated carbon samples B, C, and D at temperatures ranging from 303 to 333 K and the thermodynamics of adsorption have been investigated using a vacuum adsorption apparatus in order to obtain more information about the effect of CO2 on removal of organic sulfur-containing compounds in industrial gases. The active ingredients impregnated in the carbon samples show significant influence on the adsorption for CO2 and its volumes adsorbed on modified carbon samples B, C, and D are all larger than that on the raw carbon sample A. On the other hand, the physical parameters such as surface area, pore volume, and micropore volume of carbon samples show no influence on the adsorbed amount of CO2. The Dubinin-Radushkevich (D-R) equation was the best model for fitting the adsorption data on carbon samples A and B, while the Preundlich equation was the best fit for the adsorption on carbon samples C and D. The isosteric heats of adsorption on carbon samples A, B, C, and D derived from the adsorption isotherms using the Clapeyron equation decreased slightly increasing surface loading. The heat of adsorption lay between 10.5 and 28.4 kJ/mol, with the carbon sample D having the highest value at all surface coverages that were studied. The observed entropy change associated with the adsorption for the carbon samples A, B, and C (above the surface coverage of 7 ml/g) was lower than the theoretical value for mobile adsorption. However, it was higher than the theoretical value for mobile adsorption but lower than the theoretical value for localized adsorption for carbon sample D.     

Growth of Single-walled Carbon Nanotubes on Substrates Using Carbon Monoxide as Carbon Source

The growth of single-walled carbon nanotubes(SWCNTs) on substrates has attracted great interests because of the potential applications in various fields. Carbon monoxide(CO) was used as the carbon source for the growth of SWCNTs on silicon substrates. Random or oriented SWCNTs can be produced by varying the CO flow rate. When the flow rate of CO was as low as 20 sccm(sccm:standard cubic centimeter per minute), dense SWCNT networks with clean surface were produced. When the flow rate was above 50 sccm, vertically aligned SWCNT(VA-SWCNT) arrays were grown. Well-aligned VA-SWCNT arrays were obtained in the temperature range of 650-800℃ and the content of large-diameter(above 1.7 nm) tubes in the array increased with the temperature. The height of the array was affected by the growth temperature, the CO flow rate, and the growth time. These findings indicate CO can be used as an efficient carbon source for the growth of SWCNTs on substrates under low flow rates.     

埃洛石纳米管模板法一步法制备一维碳纳米管/碳纳米棒混合纳米碳材料

利用埃洛石纳米管(HNTs)特有的中空纳米结构,以及丰富的界面化学性质,以聚乙烯醇(PVA)为碳源,采用浸渍填充纳米孔方法实现了一步制备一维碳纳米管(CNTs)/碳纳米棒(CNRs)混合纳米碳材料。考察模板剂(HNTs)和碳源(PVA)之间的比例关系对混合纳米碳材料的结构影响,利用XRD、FTIR、Raman、N2吸附-脱附测试、TEM、SEM以及电阻率和分散性等表征手段分析混合纳米碳材料的结构变化。结果发现,PVA填充含量的增加将导致产物中CNRs的质量分数增加;当PVA和HNTs质量之比为1∶1时,所制备的CNTs/CNRs的孔体积达到最大值2.142 cm~3·g-1,比表面积达到583 m~2·g-1,并且表现出较好的电导率和分散性,表明低的PVA填充比例制备的混合碳材料中CNTs含量较高。     

Carbon clusters

Some of the most significant discoveries and achievements concerning the mass spectra and gas phase ion chemistry of carbon clusters are reviewed. These include (1) nanosecond and femtosecond laser ionizations; (2) ion structures through ion/molecule reactions, ion chromatography, and computational methods; (3) carbon cluster cooling through radiative decay, dissociative decay, and thermionic emission; (4) mechanisms and energetics of fragmentation reactions; (5) endohedral fullerenes including recent data on ion beam implantation, and (6) ion chemistry as a function of the fullerene charge state.     

二氧化碳与低碳经济发展

由于二氧化碳无色无味,又存在于大气中,因此它在植物生长中的重要性被人类忽略了。其实二氧化碳是光合作用的反应物,是植物生长的重要原料;又是一种新型绿色肥料。人类应该着力开发以二氧化碳为原料的新型肥料发展低碳经济。     

Ni/γ-Al2O3催化剂上CH4-CO2重整体系中积碳-消碳的研究

用动态热重技术和色谱技术联用以及XRD和TEM等表征手段,研究了Ni/γ-Al     

Palladium-Catalyzed Addition of Carbon Monoxide and Carbon Tetrachloride to 1-Octene in Supercritical Carbon Dioxide

The Pd-catalyzed addition of carbon monoxide and carbon tetrachloride to 1-octene gave coadduct [alkyl 2-( 2, 2, 2-trichloroethyl)octanoate] as the major product in supercritical carbon dioxide by using pyridine as the base. It was found that the selectivity and the yield of coadduct were greatly affected by the pressure of carbon dioxide, the reaction temperature and the amounts of alcohol and base used.     

碳纳米管含量对炭炭复合材料组织及力学性能的影响

炭纤维上原位合成了均匀生长且具有伸张形貌的碳纳米管,借助化学气相渗透制备了碳纳米管增强的炭炭复合材料,研究了不同含量的碳纳米管对炭炭复合材料组织和力学性能的影响。结果表明：炭纤维上生长碳纳米管改变了热解炭的沉积行为,诱导了各向同性热解炭的生成,且随着碳纳米管含量的增加,各向同性热解炭的厚度增加,但是复合材料的d002值却明显降低。微量的碳纳米管即可显著提高复合材料的力学强度,随着其含量的增加,复合材料的力学强度和模量迅速提高,但材料的断裂行为却急剧恶化,断裂模式由最初的假塑性断裂转变为脆性断裂。