Evaluation of electrodeposited tungsten chemical modifier for direct determination of chromium in urine by ETAAS

The direct determination of chromium in urine by electrothermal atomic absorption spectrometry (ETAAS) using graphite tubes modified with tungsten is proposed. Modification of the graphite is made by tungsten electrodeposition over the whole surface atomizer followed by carbide formation by heating the tube inside its own furnace. For tungsten electrocoating, the graphite tube and a platinum electrode were connected to a power supply as cathode and anode, respectively, and immersed in a solution containing 2 mg of W in 0.1% v/v HNO₃. Then, 5 V was applied between the electrodes during 20 min for tungsten electrodeposition over the whole atomizer. A SpectrAA 220 Varian atomic absorption spectrometer equipped with a deuterium background corrector was used throughout. Undiluted urine (20 μl) was delivered over the tungsten-treated tube and the chromium-integrated absorbance was measured after applying a suitable heating program with maximum pyrolysis at 1300 °C and atomization at 2500 °C. With electrodeposited tungsten modifier, the tube lifetime increased up to four times when compared to previous published methods for Cr determination in urine by ETAAS, reaching 800 firings. Method detection limit (3 S.D.) was 0.10 μg l⁻¹, based on 10 integrated absorbance measurements of a urine sample with low Cr concentration. Two reference materials of urines (SRM 2670) from National Institute of Standards and Technology (NIST) were analyzed for method validation. For additional validation, results obtained from eight human urine samples were also analyzed in a spectrometer with Zeeman effect background correction.     

Preparation and characterization of silica—polyimide composite membranes coated on porous tubes for CO2 separation

Silica-polyimide microcomposite membranes were prepared on γ-alumina-coated α-alumina support tubes, and their gas permeation properties were evaluated with He, N₂ and CO₂. Smoothing of the substrate surface and hybridization of silica and polyamic acid were both effective to form defect-free thin composite membranes. The CO₂ permeance of a membrane with a silica content of 68 wt% was one order of magnitude higher than that of a polyimide membrane having the same thickness. The permselectivity of CO₂ to N₂ was 30 at 30°C and 13 at 100°C. Contributions of the silica and polyimide phases to permeance of the composite membrane were analyzed with a two-phase permeation model. The effective thickness of the rate-controlling polyimide phase was less than one-tenth of the total thickness of the silica-polyimide membrane.     

Gas permeation of porous organic/inorganic hybrid membranes

Selective gas permeation of porous organic/inorganic hybrid membranes via sol-gel route and its thermal stability are described. Separation performance of the hybrid membrane was improved compared with porous membranes governed by the Knudsen flow, and gas permeability was still much higher than that through nonporous membranes. Additionally, it was shown that these membranes were applicable at higher temperatures than organic membranes.SEM observation demonstrated that the thin membrane was crack-free. Nitrogen physisorption isotherms showed the pore size was in the range of nanometers. Gas permeability through this membrane including phenyl group was in the range of 10^–8 [cc(STP) cm/(cm² s cmHg)] at 25°C. The ratios of O₂/N₂ and CO₂/N₂ were 1.5 and 6.0, respectively, showing the permeation was not governed by the Knudsen flow. The permeability decreased as the temperature increased. Furthermore, the specific affinity between gas molecules and surface was observed not only in the permeation data of the hybrid membranes but in the physisorption data. These results suggested that the gas permeation through the hybrid membrane was governed by the surface flow mechanism.Thermal analysis indicated that these functional groups were still stable at higher temperatures. The phenyl group especially remained undamaged even at 400°C.     

An Accurate Equation for the Electrolytic Conductivity of Potassium Chloride Solutions

An empirical equation has been developed to model the electrolytic conductivity of potassium chloride (KCl) solutions over the temperature range 0 to 55 °C (ITS-90) and molality concentrations from 0 to 5 mol⋅kg⁻¹ (H₂O). The National Institute of Standards and Technology (NIST) Demal values are treated as the defining data and selected historical data provided further data. Changes in the definition of the ohm, liter and temperature scales have been identified and the historical data were converted to modern units. The accuracy of the equation is estimated to be equal to 0.03% as suggested by NIST as the accuracy of these data.     

Effect of clay on the corrosion protection efficiency of PMMA/Na-MMT clay nanocomposite coatings evaluated by electrochemical measurements

The preparation of PMMA-clay nanocomposites was investigated by using sodium dodecylbenzenesulfonate (SDS) and potassium peroxodisulfate (KPS) as a surfactant and chain initiator for an in situ emulsion polymerization reaction, respectively. The as-prepared nanocomposites were then characterized by Fourier transformation infrared (FTIR) spectroscopy, wide-angle X-ray diffraction (WAXRD) patterns and transmission electron microscopy (TEM).It should be noted that the nanocomposite coating containing 1 wt% of clay loading was found to exhibit an observable enhanced corrosion protection on cold-rolled steel (CRS) electrode at higher operational temperature of 50 °C, which was even better than that of uncoated and electrode-coated with PMMA alone at room temperature of 30 °C based on the electrochemical parameter evaluations (e.g., E_corr, R_p, I_corr, R_corr and impedance). In this work, all electrochemical measurements were performed at a double-wall jacketed cell, covered with a glass plate, through which water was circulated from a thermostat to maintain a constant operational temperature of 30, 40 and 50 ± 0.5 °C. Moreover, a series of electrochemical parameters shown in Tafel, Nyquist and Bode plots were all used to evaluate PCN coatings at three different operational temperatures in 5 wt% aqueous NaCl electrolyte. The molecular barrier properties at three different operational temperatures of PMMA and PCN membranes were investigated by gas permeability analyzer (GPA) and vapor permeability analyzer (VPA). Effect of material composition on the molecular weight and optical properties of neat PMMA and PCN materials, in the form of solution and membrane, were also studied by gel permeation chromatography (GPC) and UV-vis transmission spectra.     

Nanopore Size Growth and Ultrafiltration Performance of SnO2 Ceramic Membranes Prepared by Sol-Gel Route

Supported ceramic membranes have been produced by the sol-casting procedure from aqueous colloidal suspensions prepared by the sol-gel route. Coatings on a tubular alumina support have been successfully performed leading to crack free layers. Samples have been sintered at 400, 500 and 600°C, and the effect of heating treatment on the nanostructure and on the ultrafiltration properties are analyzed. The characterization has been done by high resolution scanning electron microscopy, nitrogen adsorption-desorption isotherms, water permeation and cut-off determination using polyethylene glycol standard solutions. The micrographs have revealed that grains and pore size increase with the temperature, whereas their shape remains invariant. This results is in agreements with N₂ adsorption-desorption analyses, which have revealed that the mean pore size diameter increases from 4 to 10 nm as the sintering temperature increases from 400 to 600°C, while the total porosity remains constant. Furthermore, the tortuosity, calculated from water permeability, is essentially invariant with the sintering temperatures. The membranes cut-off, determined with a retention rate equal to 95%, are 3500, 6500 and 9000 g·mol^–1 for 400, 500 and 600°C, respectively, showing that the permeation properties of SnO₂ ultrafiltration membranes can easily be controlled by sintering condition.     

Synthesis of Nd-doped barium cerate proton conductor from oxalate coprecipitate precursor

The decomposition process of barium, cerium and neodymium oxalates in air was investigated by DTA-TG. Decomposition of an oxalate coprecipitate precursor and formation of barium cerate were examined in air, N₂ and CO₂ atmospheres, respectively, by employing DTA-TG and XRD. The results showed that, in air, cerium oxalate could easily be decomposed to CeO₂ below 350°C and Nd₂O₃ could be obtained at 670°C, while a high temperature of >1400°C was needed to obtain BaO. Although some amount of BaCeO₃ was formed at 500°C in air, at 650°C in N₂ and at 800°C in CO₂, single perovskite phase of BaCeO₃ could only be obtained at a much higher temperature.This work is supported by the National Natural Science Foundation of China under Grant No. 59372103. F. L. Chen is grateful to Danish International Development Assistance (Danida) and State Science and Technology Commission (SSTC) of China for offering this joint Ph. D. study at Materials Department, Risø National Laboratory. Dr. N. Bonanos at Risø National Laboratory is acknowledged for his constant interest and encouragement to this work. Special thanks are given to P. V. Jensen and T. R. Strauss for their experimental assistance.     

Flow injection atomic absorption spectrometery for the standardization of arsenic, lead and mercury in environmental and biological standard reference materials

Results of a thorough study and application of flow injection atomic absorption spectrometry for the determination of As, Pb and Hg in parts per million to sub-parts per billion levels in environmental and biological samples have been described. Various standard reference materials from the National Bureau of Standards, USA, the National Institute of Standards and Technology, USA, the Community Bureau of Reference, Brussels, Belgium and the National Institute for Environmental Studies, Japan and Standard Chinese river sediment were used. By flow injection hydride generation AAS the standard reference materials were analyzed for As and Pb. Mercury was determined by cold vapour flow injection AAS from environmental and biological standard reference materials. The technique is fast, simple and highly sensitive. It takes only 30 s for each analysis from the digested solution. The detection limits of As, Pb and Hg are 1.8 μg L^–1 and 2.0 μg L^–1 and 1.5 μg L^–1, respectively. The results show good agreement with the certified values. Received: 9 May 1996 / Revised: 13 August 1996 / Accepted: 14 August 1996     

Evaluation of capillary gas chromatography for the measurement of hydrocarbons by participating in an intercomparison experiment

Summary By participating in an International Hydrocarbons Intercomparison Experiment, a method for the determination of nonmethane hydrocarbons was evaluated. The method involves Tenax-TA sampling, thermal desorption and preconcentration combined with capillary gas chromatography with flame ionization detection. Sixty target compounds from C₂ to C₁₁ were separated by using a megabore capillary column with a thick film of bonded nonpolar siloxane stationary phase (5 μm, Rtx-1). The unusually thick film in the column was an advantage for resolving light hydrocarbons (C₂−C₃) at room temperature. The percent difference between the National Institute of Standards and Technology (NIST) and our laboratory in the intercomparison experiment is in the range of 0.99%–19.70%.     

Biological reference materials for assaying human albumin in urine

Summary To assess the interlaboratory variation in the results of albumin measurements, we prepared albumin solutions in human urine at various concentrations within the normal range. Since some investigators have reported that albumin is unstable in some human urine samples stored at –20°C, we screened urine samples from 21 persons to identify samples that were stable under these conditions and that had low native albumin content. The urine of two donors met these criteria, and they provided urine, which we prefiltered, sterile-filtered, and spiked with commercially available human serum albumin. The albumin was characterized as pure by a Lowry assay of protein content with National Institute of Standards and Technology bovine serum albumin (standard reference material 926) as the standard and by the appearance of one band on agarose gel electrophoresis. To evaluate the necessity for additional stabilization when urine samples are stored at –20°C, a surfactant was included in one set of materials and not included in another. The materials with surfactant have been evaluated for 10.5 months and those without surfactant for 5 months. The preserved materials showed no significant loss of activity during this period. The unpreserved materials remained stable for 2 months, and then the two higher level materials appeared to loose activity. The negative slope of the highest level of unpreserved material was statistically significant (p=0.01) during this period. In our laboratory, the albumin recovered by enzyme immunoassay was 106.7% and 115.9% in two preserved normal-range materials and 102.2% and 106.3% in similar unpreserved materials.     

Isolation and characterization of hemicelluloses and cellulose from rye straw by alkaline peroxide extraction

Extraction of water-treated rye straw with 2% H₂O₂ at pH 11.5 for 12 h at 20 °C, 30 °C, 40 °C, 50 °C, 60 °C, and 70 °C, released 44.2–71.9% of the original hemicelluloses and 52.7–87.8% of the original lignin. As a comparison, treatment of the straw with a dilute alkaline solution at pH 11.5 for 12 h at 50 °C, in the absence of H₂O₂ yielded only 7.3% of the original hemicelluloses and 7.4% of the original lignin. Xylose was the predominant sugar constituent in the seven solubilized hemicellulosic preparations, and arabinose, glucose, and galactose were present in small amounts. The hemicellulosic samples were further characterized by Fourier transform infrared (FT-IR), and carbon-13 magnetic resonance spectroscopy (¹³C-NMR), gel permeation chromatography (GPC), and nitrobenzene oxidation of the associated lignin, and the results are reported. The most obvious feature was found that the alkaline peroxide treatment of the straw under the conditions used did not affect the overall structure of the hemicelluloses as compared to the hemicelluloses isolated with alkali from delignified rye straw.     

Development of a transportable system for radionuclide analysis

Transportable radioanalytical systems were assembled and tested for quantitative determination of γ-emitting radionuclides and screening of β-emitting radionuclides. Standard operating procedures (SOPs), including instructions for assembly, disassembly, operation, sample collection and analysis, and all other procedures needed, were developed. Foods, as well as National Institute of Standards and Technology, International Atomic Energy Agency, and in-house Reference Materials were analyzed. An SOP for γ-emitting radionuclides was successfully tested at 3 locations.     

Extract–filter–shoot liquid chromatography with mass spectrometry for the analysis of vitamin D2 in a powdered supplement capsule and standard reference material 3280

An “extract–filter—shoot” method for the analysis of vitamin D₂, ergocalciferol, in a dry powdered dietary supplement capsule containing rice flour excipient and in a National Institute of Standards and Technology standard reference material 3280 is reported. Quantification of vitamin D₂ was done by atmospheric pressure chemical ionization mass spectrometry using selected ion monitoring, two transitions of selected reaction monitoring, and extracted ion chromatograms from full scans. UV detection was used for the quantification of Vitamin D₂ in the dry powder capsule, whereas interfering species rendered UV detection unreliable for standard reference material 3280. Average values for standard reference material 3280 ranged from 8.27 ± 0.58 to 8.33 ± 0.57 μg/g using internal standard calibration and response factor approaches, compared to the previous National Institute of Standards and Technology internal value for vitamin D₂ of 8.78 ± 0.11 μg/g, and the recently updated reference value of 8.6 ± 2.6 μg/g. The powdered supplement capsule was found to contain 28.19 ± 0.35 to 28.67 ± 0.90 μg/capsule for a capsule labeled to contain 25.00 μg. The triacylglycerol composition of the rice flour excipient in the powdered supplement capsule determined by atmospheric pressure chemical ionization mass spectrometry is also reported.     

Permeability control of metal ions using temperature- and pH-sensitive gel membranes

Temperature- and pH-sensitive copolymer gels were synthesized by the simultaneously occurring radiation-induced polymerization and self-bridging of acryloyl- -proline methyl ester (A-ProOMe) with acrylic acid (AAc) in aqueous solutions. The gel swelling behavior and the metal permeation characteristic of its gel membrane were investigated with regard to very slight changes of temperature and pH. The pH threshold of the swelling of a copoly(A-ProOMe/AAc, 70/30 mol%) gel in the range of 5–30°C lay in the region between pH 4.0 and 5.0. The permeability results of metal ions showed that at 40°C the gel membrane blocks the permeation of lithium (Li) and cesium (Cs) ions at pH values lower than 4.75 and 4.60, respectively. The permselectivity (P_Li/Cs value) of the two metal ions at 30°C was also studied and, as a result, its value was obtained to be 1.33 at pH 4.65 and 30°C. This permeation study indicates that the selective metal separation of copoly(A-ProOMe/AAc) gel membranes can be controlled by changing temperature and pH values.     

Neutron captue prompt gamma-ray activation analysis at the NIST Cold Neutron Research Facility

An instrument for neutron capture prompt gamma-ray activation analysis (PGAA) has been constructed as part of the Cold Neutron Research Facility at the 20 MW National Institute of Standards and Technology Research Reactor. The neutron fluence rate (thermal equivalent) is 1.5·10⁸ n ·cm^–2·s^–1, with negligible fast neutrons and gamma-rays. With compact geometry and hydrogen-free construction, the sensitivity is sevenfold better than an existing thermal instrument. Hydrogen background is thirtyfold lower.     

Ni-based amorphous alloy membranes for hydrogen separation at 400 °C

Amorphous alloy membranes composed primarily of Ni and early transition metals (ETMs) are an inexpensive alternative to Pd-based alloy membranes, and these materials are therefore of particular interest for the large-scale production of hydrogen from carbon-based fuels. Catalytic membrane reactors can produce hydrogen directly from coal-derived synthesis gas at 400 °C, by combining a commercial water–gas-shift (WGS) catalyst with a hydrogen-selective membrane. In order to explore the suitability of Ni-based amorphous alloys for this application, the thermal stability and hydrogen permeation characteristics of Ni–ETM amorphous alloy membranes has been examined. A fundamental limitation of these materials is that hydrogen permeability is inversely proportional to the thermal stability of the alloy. Alloy design is therefore a compromise between hydrogen production rate and durability. Amorphous Ni₆₀Nb_40−XZr_X membranes have been tested at 400 °C in pure hydrogen, and in simulated coal-derived gas streams with high steam, CO and CO₂ levels, without severe degradation or corrosion-induced failure. Ni–Nb–Zr amorphous alloys are therefore prospective materials for use in a catalytic membrane reactor for coal-derived syngas.     

Determination of trace and toxic elements in Korean rice CRM by INAA, ICP and AAS

Trace and toxic elements in Certified Reference Material (CRM) made of Korean rice at the Korea Research Institute of Standards and Science have been analyzed by Instrumental Neutron Activation Analysis (INAA). Data intercomparison from the measurement with those of Atomic Absorption Spectrometry (AAS) and Induced Coupled Plasma Spectrometry (ICPS) has been studied. The powdered samples were sterilized at 1.5·10⁶ rad in the bottles using a⁶⁰Co source after sieving and spiking to specific elements such as As, Cd, Cr, Cu and Hg and then the homogeneity of samples was assessed. Rice flour (SRM 1568a) and standard solutions made by the National Institute of Standards Technology (NIST) were used to construct the calibration curves for the INAA and the chemical methods, respectively. The uncertainties and concentration of constituent elements were determined and the possibility of their use for analytical quality control was considered.     

C2 and C3 hydrocarbon separations in poly(1,5-naphthalene-2,2′-bis(3,4-phthalic) hexafluoropropane) diimide (6FDA-1,5-NDA) dense membranes

The transport of olefin and paraffin namely ethane, ethylene, propane and propylene in aromatic poly(1,5-naphthalene-2,2′-bis(3,4-phthalic) hexafluoropropane) diimide (6FDA-1,5-NDA) dense membranes was investigated. The gas permeability coefficients were measured at pressures from 2.5 to 16 atm for the C₂ hydrocarbon gases and pressures up to 8.4 atm for C₃ systems at 35 °C. This membrane exhibits permeabilities of 0.15, 0.87, 0.023 and 0.24 Barrer with respect to pure ethane, ethylene, propane and propylene, and shows an ideal selectivity of 5.8 for the separation of ethylene/ethane, 10 for propylene/propane, 7.6 for nitrogen/ethane and 50 for nitrogen/propane. The olefins showed a preferred permeability to paraffins and discussion were drawn to the permeability, diffusivity and solubility coefficients. The activation energies of permeation, diffusion and solution were also reported and the effect of temperature on the permeation properties was discussed for the pure gas permeability data obtained from 30 to 50 °C. The plasticisation effect was also found for propane and propylene, respectively, although it was neither detected in the saturated nor unsaturated C₂ hydrocarbons at pressures up to 16 atm.     

Routine,high-sensitivity,cold vapor atomic absorption spectrometric determination of total mercury in foods after low-temperature digestion

A cold vapor atomic absorption spectrometric method was developed for the subnanogram-per-gram determination of total Hg in a wide variety of foods. Foods were weighed into 50 mL polypropylene centrifuge tubes and dried without charring at 55 degrees C in a circulating oven. Samples were then digested at 58 degrees C with HNO3, HCl, and H2O2. After matrix modification with solutions of 2% Mg(NO3)2, 0.01% Triton X-100, and Cu(II) at 10 microg/mL, samples were analyzed by using a CeTAC Technologies M-6000A dedicated Hg analyzer. Based on a 2 g sample weight, the detection limit of the method over 12 batches averaged 0.30 ng/g wet weight and ranged from 0.03 to 0.6 ng/g. Recoveries of Hg added to 17 different foods, analyzed in a routine manner, averaged 97%, and individual recoveries ranged from 77 to 107%. Accuracy was confirmed by analysis of 7 biological reference materials from the National Research Council of Canada and the National Institute of Standards and Technology. Stabilization of low concentrations of Hg in solutions containing no sample was required to prevent loss of Hg from blanks. In a comparison of NaCl, potassium dichromate, and Au(II), chloride was much more effective for stabilization than the other two, and HCl was used for subsequent stabilization.     

Direct measurement ofk o for monitor neutron activation analysis

This paper introduces the thermal column or the cold neutron guide beam of the 20 MW NBSR at the National Institute of Standards and Technology as a directk _o measurement facility. Measurement ofk _o at this facility not only produces accurate values, but avoids the additional correction factors needed in other measurement methods. Thek _o of Sb, Ag and Cr with respect to Sc as monitor have been measured and their values are comparable to values based on tabulated nuclear constants and to those measured by other researchers.