Formation of alkanethiol monolayer on Ge(111).

Alkanethiols, CH3(CH2)(n-1)SH, are shown to react readily with HF-treated Ge(111) surface at room temperature to form a high-quality monolayer. The resulting films are characterized by using contact angle analysis (CAA), atomic force microscopy (AFM), X-ray photoelectron spectroscopy (XPS), spectroscopic ellipsometry (SE), and high-resolution electron energy loss spectroscopy (HREELS). The octanethiol and octadecanethiol films on Ge(111) both exhibit 101 degrees and 40 degrees water and hexadecane contact angles, respectively. These values indicate that the thiol surface coverage is relatively high, and that the films possess a high degree of orientational ordering. The angle-resolved XPS analysis supports that thiols are bound to the Ge surface by Ge-S bonds at the monolayer/Ge interface. The film thickness values obtained by XPS and SE agree well with the earlier reported values on alkyl monolayers on Ge(111) prepared by Grignard reaction. On the basis of HREEL spectra taken after thermal annealing steps, the monolayers are found to be thermally stable up to 450 K. The thermal stability provides further evidence that thiols are covalently bonded to Ge(111).     

乙醇在碳载Pt纳米薄膜电极上吸附氧化过程研究Ⅰ.碱性介质中循环伏安和原位FTIR反射光谱

运用电化学循环伏安法在玻碳载体上制备纳米级厚度的Pt薄膜电极 ,用STM表征电极表面的形貌 ,测定了电沉积层的厚度、表面积和Pt载量 .同时 ,应用电化学循环伏安法和原位FTIR反射光谱研究了乙醇在碱性介质中的吸附和氧化行为 .结果表明 ,乙醇氧化的主要产物是CH3COO- ,仅存在少量乙醛 ,并未观察到任何CO谱峰 .与酸性介质中乙醇氧化的双途径机理不同 ,碱性介质中乙醇氧化未经过解离吸附中间过程     

Ni/Pt(111) bimetallic surfaces: unique chemistry at monolayer ni coverage.

We have utilized the dehydrogenation and hydrogenation of cyclohexene as probe reactions to compare the chemical reactivity of Ni overlayers that are grown epitaxially on a Pt(111) surface. The reaction pathways of cyclohexene were investigated using temperature-programmed desorption, high-resolution electron energy loss (HREELS), and near edge X-ray absorption fine structure (NEXAFS) spectroscopy. Our results provide conclusive spectroscopic evidence that the adsorption and subsequent reactions of cyclohexene are unique on the monolayer Ni surface as compared to those on the clean Pt(111) surface or the thick Ni(111) film. HREELS and NEXAFS studies show that cyclohexene is weakly pi-bonded on monolayer Ni/Pt(111) but di-sigma-bonded to Pt(111) and Ni(111). In addition, a new hydrogenation pathway is detected on the monolayer Ni surface at temperatures as low as 245 K. By exposing the monolayer Ni/Pt(111) surface to D2 prior to the adsorption of cyclohexene, the total yield of the normal and deuterated cyclohexanes increases by approximately 5-fold. Furthermore, the reaction pathway for the complete decomposition of cyclohexene to atomic carbon and hydrogen, which has a selectivity of 69% on the thick Ni(111) film, is nearly negligible (<2%) on the monolayer Ni surface. Overall, the unique chemistry of the monolayer Ni/Pt(111) surface can be explained by the weaker interaction between adsorbates and the monolayer Ni film. These results also point out the possibility of manipulating the chemical properties of metals by controlling the overlayer thickness.     

团聚铂纳米粒子电极在甲醇氧化中的电催化特性

用H2还原法并以Nafion作为稳定剂合成团聚的Pt纳米粒子，附载于玻碳表面制备电催化剂.透射电子显微镜（TEM）和扫描电子显微镜（SEM）表征结果指出,团聚Pt纳米粒子的平均尺寸约为400 nm.运用电化学循环伏安法(CV)和原位傅立叶变换红外反射光谱（in situ FTIRS）研究甲醇的氧化过程，发现团聚Pt纳米粒子电极具有较高的电催化活性.原位FTIRS研究结果检测到甲醇在所制备的电催化剂上氧化的中间体为线型吸附态CO物种，其红外吸收给出异常红外效应的光谱特征.     

Structural rearrangement of c(70) monolayers induced by octanethiol adsorption

Mixed monolayers of C70 and octanethiol are prepared on Au(111) by a sequential adsorption method. A partial C70 monolayer is first formed and characterized, followed by the vapor deposition of octanethiol. This results in a well-ordered alkanethiol film where single C70 molecules and small molecular clusters are located at domain boundaries and in disordered regions. Substrate step defects have a large influence on the spatial distribution of C70; adjacent to a substrate defect, C70 binds preferentially on the upper terrace and is depleted on the lower terrace. We explain these observations as resulting from the kinetics of alkanethiol monolayer formation, and we present a simple model for the evolution of surface structure in the C70/octanethiol system.     

乙醇在碳载Pt纳米薄膜电极上吸附和氧化过程研究——II.酸性介质中EQCM和原位FTIR反射光谱

运用电化学循环伏安 ,石英晶体微天平 (EQCM )和原位FTIR反射光谱等方法研究了酸性介质中乙醇在碳载纳米Pt膜电极上吸附和氧化行为 .结果表明 ,乙醇的电氧化与溶液酸碱性及电极表面氧物种有密切的关系 ,并指出乙醇电催化氧化是通过解离吸附产物和反应中间体双途径机理进行的 .在实验条件下 ,经原位FTIR反射光谱检测 ,解离吸附产物为CO ,反应中间体主要有CH3COOH和CH3CHO等物种 .     

Au@Pt纳米粒子单层膜对甲醇氧化的电催化性能及SERS研究

通过种子生长法合成Au@Pt核壳结构纳米粒子,采用两相成膜法制备单层粒子膜,并转移获得Au@Pt核壳纳米粒子单层膜电极,该电极表面纳米粒子分布均匀,具有较大的比表面,对甲醇的氧化具有较好的电催化活性.研究表明,利用内核Au的长程电磁场增强效应,该单层膜表现出均匀且优良的表面增强拉曼散射(SERS)活性,适合作为基底在分子水平上研究表面的吸附和反应.获得了Au@Pt核壳纳米粒子单层膜表面甲醇电催化氧化过程的SERS光谱,为深入分析表面反应机理提供了实验依据.     

Determination of thickness, dielectric constant of thiol films, and kinetics of adsorption using surface plasmon resonance

This paper describes the formation of a self-assembled monolayer of 11-mercaptoundecanoic acid (MUA) under different concentrations on a gold sensor disk, monitoring in situ and in real time using surface plasmon resonance spectroscopy (SPR). The film thickness and dielectric constant were determined for a fully formed monolayer using one-color approach SPR. The kinetic studies of the film formation in ethanol solution indicated that the self-assembled monolayer is formed in a two-step adsorption process. In this sense, this unpublished route was applied on the basis of a model where many molecules are adsorbed at an initial step and then can be desorbed and/or rearranged to form a perfect monolayer.     

Bonding and structure of glycine on ordered Al2O3 film surfaces

The interaction between glycine (NH2CH2COOH) layers and an ultrathin Al2O3 film grown epitaxially onto NiAl(110) was studied by temperature-programmed desorption, X-ray photoelectron spectroscopy, ultraviolet photoelectron spectroscopy, work function measurements, and near-edge X-ray absorption fine structure (NEXAFS) spectroscopy. At monolayer coverages at 110 K, there are two coexisting molecular forms: the anionic (NH2CH2COO-) and the zwitterionic form (NH3+CH2COO-) of glycine. As deduced from the photoemission data, the buildup of multilayers at 110 K leads to a condensed phase predominantly in the zwitterionic state. In contrast to the monolayer at 110 K, the monolayer formed at 300 K consists primarily of glycine molecules in the anionic state. The latter species is adsorbed with the oxygen atoms of the carboxylic group pointing toward the substrate. The polarization-dependent C K- and O K-edge NEXAFS spectra indicate that the glycinate species in the monolayer at 300 K is oriented nearly perpendicular to the surface, with the amino group pointing away from the surface.     

In situ electrodeposition of Pt nanoclusters on glassy carbon surface modified by monolayer choline film and their electrochemical applications

Pt nanoclusters attached to the monolayer choline (Ch) modified glassy carbon surface were successfully synthesized by use of in situ cyclic voltammetry (CV) method. Field emission scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), and electrochemical impedance spectroscopy (EIS) were used to characterize the properties of this modified electrode. It was demonstrated that Ch was immobilized onto the carbon surface forming a covalently planted Ch monolayer, which could induce the formation of Pt nanoclusters. The preliminary study found that the homogeneous nanostructured Pt/Ch film exhibited remarkable electrocatalytic activity towards the oxidation of methanol and nitrite.     

原位生长Pd/Ni(OH)2/NF复合催化剂及其析氢性能

采用水热合成法在泡沫镍上原位构建了低贵金属含量的钯/氢氧化镍纳米复合催化剂（Pd/Ni（OH）₂/NF）。通过扫描电镜,能谱仪,X射线衍射仪和X射线光电子谱仪等分析技术表征了催化剂的形貌和微观结构;运用线性扫描伏安法,电化学阻抗谱和计时电流法等手段研究了催化剂的催化析氢性能。实验结果显示复合催化剂具有特殊的微观构型,超薄的Ni（OH）₂薄片生长在泡沫镍表面,纳米尺寸的钯均匀地镶嵌在氢氧化镍薄片中。催化剂表面的氢氧化镍有利于促进水的解离,加快氢中间体的形成;均匀分散的钯极易吸附解离的氢中间体,快速地复合成氢气分子。我们发现复合催化剂能协同加快析氢反应过程,极大地降低析氢过电位,提高了析氢活性。此外,复合催化剂原位生长在泡沫镍上,有效地提高了催化电极的稳定性。     

Heat-stabilized glycosphingolipid films for biosensing applications

We have investigated a means of producing thin, oriented lipid monolayers which are stable under repeated washing and which may be useful in biosensing or surface-coating applications. Phosphatidylcholine and the glycosphingolipid GM1 were used as representative lipids for this work. Initially, a mixed self-assembled monolayer of octanethiol and hexadecanethiol was produced on a gold surface. This hydrophobic monolayer was then brought into contact with a thin lipid film that had been assembled at the liquid/air interface of a solution, allowing the lipid to deposit on the gold surface through hydrophobic interactions. The lipid layer was then heated to cause intermingling of the fatty acid and alkanethiol chains and cooled to form a highly stable film which withstood repeated rinsing and solution exposure. Presence and stability of the film were confirmed via ellipsometry, Fourier transform infrared spectroscopy, and quartz crystal microbalance (QCM), with an average overall film thickness of approximately 3.5 nm. This method was then utilized to produce GM1 layers on gold-coated QCM crystals for affinity sensing trials with cholera toxin. For these sensing elements, the lower detection limit of cholera toxin was found to be approximately 0.5 microg/mL, with a logarithmic relationship between toxin concentration and frequency response spanning over several orders of magnitude. Potential sites for nonspecific adsorption were blocked using serum albumin without sacrificing toxin specificity.     

Comparison of Si-O-C interfacial bonding of alcohols and aldehydes on Si(111) formed from dilute solution with ultraviolet irradiation

Aliphatic alcohols and aldehydes were reacted with the Si(111)-H surface to form Si-O-C interfacial bonds from dilute solution by using ultraviolet light. The resulting monolayers were characterized by using transmission infrared spectroscopy, spectroscopic ellipsometry, and contact angle measurements. The effect of different solvents on monolayer quality is presented. The best monolayers were formed from CH(2)Cl(2). The optimized monolayers were thoroughly characterized to determine the film structure and monolayer stability. The UV-promoted, alcohol-functionalized, and aldehyde-functionalized monolayers are of comparable quality to those previously prepared by other means. Although both molecules are tethered through a Si-O-C bond, the film reactivity is distinctly different with the aldehyde films being more chemically resistant. The differences in chemical reactivity, vibrational spectra, hydrophobicity, and ellipsometric thickness between the alcohol and aldehyde monolayers are attributed to a difference in molecular coverage and monolayer formation.     

Collision-induced annealing of octanethiol self-assembled monolayers by high-kinetic-energy xenon atoms

Collisions with high-energy xenon atoms (1.3 eV) induce structural changes in octanethiol self-assembled monolayers on Au(111). These changes are characterized at the molecular scale using an in situ scanning tunneling microscope. Gas-surface collisions induce three types of structural transformations: domain boundary annealing, vacancy island diffusion, and phase changes. Collision-induced changes that occur tend to increase order and create more stable structures on the surface. We propose a mechanism where monolayer transformations are driven by large amounts of vibrational energy localized in the alkanethiol molecules. Because we monitor incremental changes over small regions of the surface, we can obtain structural information about octanethiol monolayers that cannot be observed directly in scanning tunneling microscopy images.     

Expression of a supramolecular complex at a multivalent interface

The multivalent binding of a supramolecular complex at a multivalent host surface by combining the orthogonal beta-cyclodextrin (CD) host-guest and metal ion-ethylenediamine coordination motifs is described. As a heterotropic, divalent linker, an adamantyl-functionalized ethylenediamine derivative was used. This was complexed with Cu(II) or Ni(II). The binding of the complexes to a CD self-assembled monolayer (SAM) was studied as a function of pH by means of surface plasmon resonance (SPR) spectroscopy. A heterotropic, multivalent binding model at interfaces was used to quantify the multivalent enhancement at the surface. The Cu(II) complex showed divalent binding to the CD surface with an enhancement factor higher than 100 relative to the formation of the corresponding divalent complex in solution. Similar behavior was observed for the Ni(II) system. Although the Ni(II) system could potentially be trivalent, only divalent binding was observed at the CD SAMs, which was confirmed by desorption experiments.     

十八硫醇自组装膜对TiO2光电氧化甲醇的敏化作用

纳米电极;甲醇光电氧化;十八硫醇自组装膜对TiO2光电氧化甲醇的敏化作用     

Comparative electrochemical study of self-assembly of octanethiol from aqueous and aqueous ethanol solutions on a gold electrode

The self-assembly of octanethiol (OT) on the surface of a polycrystalline gold electrode in aqueous and aqueous ethanol thiol-containing (1 × 10^–4 М) 0.1 М NaClO₄ solutions was studied. The blocking properties and electrochemical stability of monolayer OT films were studied by chronopotentiometry during OT adsorption under the open circuit conditions (chronoamperometry at a fixed potential) combined with cyclic voltammetry for modified Au/OT electrodes. It was found from the change in the rate of electrochemical reactions in the range of monolayer stability potentials that in aqueous media, compact insulating OT monolayer films formed at a open circuit potential within ~100 s, and the shift of the adsorption potential toward negative values (to–0.6 V) allowed a considerable decrease in the monolayer self-assembly time. The potential shift toward higher negative values (–0.9 V) leads to a removal of OT from the electrode surface during the reductive desorption, with a multipeak current signal recorded on the voltammograms. A transition from aqueous to aqueous ethanol solutions accelerated the formation of an insulating OT monolayer (≈6 s) and led to a change in the shape of the desorption current peak, whose value was almost independent of the ОТ accumulation time and potential.     

Fabrication of Ni nanoparticles by selective oxidation of permalloy thin film during imidization of polyamic acid

Ni nanoparticles embedded in a polyimide (PI) matrix were fabricated by selectively oxidizing a layer of Ni(80)Fe(20) metal film sandwiched between two PI precursor layers. Ni nanoparticles, formed in a monolayer between two PI layers, had an average particle size of approximately 5 nm. X-Ray photoelectron spectroscopy confirmed that Fe in the film was preferentially consumed, resulting in the formation of Ni nanoparticles.     

计算机硬盘基片CMP中表面膜特性的分析研究

目前,普遍采用化学机械抛光(Chemical-mechanical polishing,CMP)技术对计算机硬盘基片(盘片)表面进行原子级平整。CMP加工中,盘片表面膜及其特性对CMP过程及CMP性能具有关键作用。本文分别采用俄歇能谱(AES)、X射线光电子能谱(XPS)、扫描电镜(SEM)、纳米硬度计、电化学极化法等分析手段对盘片表面物理、化学及机械特性进行了研究,发现盘片CMP后表面发生了氧化,氧化膜在盘片的表层,厚度在纳米量级,氧化产物为Ni(OH)₂;氧化膜为较软的、疏松的、粗糙的多孔结构;氧化膜的存在加快了盘片表面的腐蚀磨损。结合盘片CMP试验结果,推测盘片的CMP机理为盘片表面氧化生成机械强度较低的Ni(OH)₂氧化膜及随后氧化膜的机械和化学去除,二者的不断循环实现表面的全局平面化。     

Formation of alkanethiol and alkanedithiol monolayers on GaAs(001)

The formation of alkanethiol (H-(CH2)n-SH, n = 8-18) and 1,8-octanedithiol (HS-(CH2)8-SH) monolayer films on n-type GaAs(001) has been systematically studied. We observed a nonlinear dependence of the film thickness on molecular length, which is drastically different from monolayer films of the same molecules on metals. For 8 < or = n < or = 14, the films are only 3-4.5 A thick, significantly smaller than the corresponding molecular length. For n = 16 and 18, the measured film thicknesses were 9 and 11 A, respectively, consistent with molecules orienting with a tilt angle of approximately 60 degrees from the surface normal. Unlike the alkanethiols, the thickness of the 1,8-octanedithiol monolayer is almost the same as its molecular length, indicating that dithiol molecules orient vertically with only one thiol end group bound to the GaAs surface. Additional support for this conclusion comes from the fact that X-ray photoelectron spectroscopy of the 1,8-octanedithiol monolayer clearly resolves two types of S atoms in the monolayer: those bound to the GaAs surface and those existing as free thiols. A suggestion was made on the mechanisms for alkanethiol and alkanedithiol monolayer formation.